Search Documents

By R Redden

"The Didipio Gold-Copper project in the Philippines has been a well-defined reasonably high gold grade porphyry for almost two decades. OceanaGold are now bringing the project into production in late 2012 and have recently reoptimised the project with the goal of combining the inherent high grades with higher through-put than previously proposed that will see strong initial metal production. The project was discovered and well defined by 1995, but has seen some obstacles to development, namely sovereign risk, capital cost and project funding. The project strengths over this time that have kept the flames alive are: strong grades large orebody with low stripping ratios a simple beneficiation process and a clean high-grade concentrate strong support from the Philippines government.The initial study in 1998 used Gold and Copper price assumptions of $325/oz and $0.95 lb respectively. Today reserves are based on $950 and $2.85. So, being a porphyry with a large reducing grade halo, the deposit now lends itself to extraction on a much larger scale than before, without any significant capital expenditure as a larger open pit now dominates the project.Didipio is a game changer for OceanaGold, so it has been important to learn from history and to capitalise on a strong initial metal production profile. The project sits in a reasonably remote mountainous area of Luzon which sees annual typhoons and numerous short duration high intensity rainfall events and two rivers flowing through the project area, so it has not been without some innovative technical solutions.CITATION:Redden, R, 2012. Didipio - Learning the lessons, adapting and getting ready for production, in Proceedings Project Evaluation 2012, pp 67-76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By Jian Liu

The dissolubility of a natural sphalerite (ZnS) in the entire pH range was theoretically calculated, and its practical dissolution in an aqueous solution at different pH values in an inert environment, together with its surface properties after dissolution, was fully investigated. The results of the investigation indicate that the total concentration of Zn (CZnT) decreases significantly with the increase of pH value, while the pH value is set below 8; however, it reverses when the pH value reaches 8. Such a tendency is similar to that of the theoretical calculations, although the experimental CZnT were much higher than those of the theoretical calculations. The X-ray photoelectron spectroscopy (XPS) of the sphalerite surface after its dissolution under alkaline solution shows that a polysulfide (Sn 2-) surface layer with a binding energy (BE) value of 162.96-163.25 eV is present on the surface, and the percentage of Sn 2- increases significantly with an increase in pH value; the undissolved and dissolved sphalerites under the acidic solution have a negligible difference in S2p peaks. The surface S/Zn ratio of all dissolved sphalerites shows a marked Zn enrichment and S deficiency. An atomic force microscope (AFM) view of the sphalerite surface, after its dissolution under the alkaline solution at a pH of 12, shows that the surface is significantly different in morphology from that of the undissolved one.

May 1, 2012

The roasting process of copper concentrates containing variable quantities of arsenic in a fluidized bed regime was analyzed, considering the technical literature published on the topic in the last quarter century. Although emphasis has been given to the analysis in the fluidized bed regime, other processes have also been considered, under a reducing, neutral or oxidizing atmosphere. The kinetic mechanisms of roasting, as well as the models that have been applied or those likely to be used to explain the kinetics of arsenic removal, are analyzed. Regarding the kinetic mechanisms, those that have been applied to copper concentrates with both high and low arsenic content are included. The roasting kinetic model includes the kinetic data analysis techniques, general models, equations and an estimation of the conversion degree through dynamic, differential and integral methods, as well as particular models for mineralogical components, such as smelter dust and copper concentrates with low and high arsenic content.

May 1, 2012

By Jennifer J. Swenson

El presente texto describe los problemas de deforestación, precios e importaciones de mercurio en la minera artesanal aurífera de Madre de Dios. En ese sentido, a medida que la interconexión de la economia mundial avanza, es más difícil que países en desarrollo aprovechen las fuerzas lucrativas de la demanda global para lograr una sostenibilidad social y ambiental. En consecuencia, los países en desarrollo contienen un peso ambiental desigual en relación con los países desarrollados qie importan materias primas. Como ejemplo de ello, el precio del oro aumentó, así como la minería aurífera informal y no industrial en los países en los países en desarrollo y el mal manejo del mercurio en el uso del oro, repercutió en el medio ambiente y los mismos mineros, al igual que el problema de la deforestación. Por ello, se plantea un programa para enfrentar dchos problemas en la región de Madre de Dios y reducir el aumento de la minería informal.

May 1, 2012

By I M. Platten, S C. Dominy

The evaluation of historical goldfields is currently topical, reflecting a high gold price, improvements in knowledge and technology. and lack of greenfield sites. Many goldfields comprise narrow gold-quartz veins which are structurally complex with an irregular distribution of gold; variable geometry and architecture; and display late deformational effects. The study of historical mine records can be an important tool during early and advanced project evaluation since it contributes to understanding the orebody, exploration target size and setting expectations. The historic Engineer Mine property is located 32 km west of Atlin, British Columbia on the east side of Tagish Lake. The economically important Engineer and Double Decker veins belong to a NNE-SSW vein set. These are narrow, commonly <2 m dilational veins with a minor sinistral strike component and of an epithermal type. Documented ore production between 1910 - 1952 is recorded as approximately 14 263 t at 39.4 g/t Au and 19.5 g/t Ag (for 18 000 oz Au and 8950 oz Ag). The underground workings consist of about 5500 m of tunnels, shafts, raises and stopes over eight levels. The mine is currently being re-evaluated. In 2011, an Inferred Mineral Resource of 41 000 t at 19 g/t Au for 25 000 oz Au (at a 5 g/t Au cut-off) was defined from historical data supported by modern drilling into the Engineer and Double Decker veins. A surface and underground bulk sampling and milling program was undertaken in 2011.CITATION:Dominy, S C and Platten, I M, 2012. Application of historical data to estimate a mineral resource at the Engineer gold mine, British Columbia, Canada, in Proceedings Narrow Vein Mining 2012 , pp 81-100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By M P. Sandy, J B. Albrecht

"Narrow vein mining can be loosely defined as mining operations involving orebodies with a true thickness of less than 4 m. Some authors have limited the term to steeper-dipping orebodies where the ore will rill under gravity. However, ænarrow veinÆ can also legitimately refer to some of the flatter orebodies, such as many of the platinum, chrome and gold deposits of Southern Africa, and several in Australasia including Bullen (at Norseman), Sunrise Dam, Telfer (Patterson, 1993) and the famous æflatmakesÆ at the Emperor Gold Mine in Fiji (Gordon and Harmse, 1993). Where the orebody dip is less than about 40¦ additional effort is usually required to remove the broken ore, including the use of scrapers, hydraulic monitors or remote-operated excavators (Tombs, Buckingham and Hancock, 2008).Working in such narrow orebodies presents particular operational and geomechanics challenges. A range of mining methods have been developed or adapted to exploit narrow orebodies including:cut-and-fill,narrow vein bench or longhole stoping,Alimak stoping,shrinkage stoping, and methods for shallow dipping orebodies (including Airleg and mechanised methods).The paper discusses some of the advantages and disadvantages of each method with a focus on geotechnical aspects including mining sequence options, stress management, ground support requirements, dilution and recovery.CITATION:Sandy, M P and Albrecht, J B, 2012. An overview of geotechnical issues in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 185-194 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

By V Mutton, L Potts, D Joyce

This paper describes the method of extracting sill pillars within the underground operation from under unconsolidated mullock fill at the Cracow Gold Mine. This pillar recovery method was initially successfully used to recover sill pillars at Crusader Mine, Western Australia in 2001. Globally significant resources have been sterilised due to the placement of loose rock fill above crown pillars and within adjacent stopes. The method described here offers significant opportunities to increase recovery of sill pillar recoveries.The royal orebody sill pillars at Cracow Gold Mine form a significant resource. Extraction of these pillars needed to be undertaken with minimal ore dilution and maximum ore recovery. The application that was selected to consolidate the loose mullock fill above each pillar used an injection grouting process (Minova FB200).Cracow Gold Mine mining method is bottom up bench mining. The pillars were left within the orebody to allow for stoping to commence whilst the decline was being developed. Due to the remainder of the orebody being extracted the only access to consolidate the backfill was from the sill pillar extraction level. Numerous problems were encountered and overcome from product selection and trial, system of injection to extraction.This pillar recovery process achieved a 95 per cent recovery of the sill pillar compared with an estimated 60 per cent typical for other mining options.CITATION:Potts, L, Mutton, V and Joyce, D, 2012. Pillar recovery at Cracow gold mine using grouted consolidated mullock, in Proceedings Narrow Vein Mining 2012 , pp 179-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By G B. Ebsworth, J Krokowski de Vickerod

Several drilling programs at Maldon have produced 7790 core samples, which were assayed for gold, with 2825 of the samples assayed for nine other metallic elements. There is a lack of correlation between gold and all other elements. The situation, however, changes dramatically when sorted according to the abundance of arsenic. In the populations where As >200 ppm, there are strong, positive correlations between gold and several elements. There is also a strong positive correlation of Au with the weighted sums and products of all elements with the elemental averages as a weighting factor, and Bi*Sb and Bi*As elemental products. In these populations, there is also a strong positive correlation between the logarithms of Au and logarithms of each element, as well as the elemental sums and products described above. The correlation coefficients increase with higher As cut-off values.All elemental distributions but especially gold show a high-nugget effect and display high skewness and dispersion, low kurtosis, and common outliers. The distributions of their logarithms are several magnitudes less scattered and without outliers. Thus, the logarithmical distribution correlations are best for practical use.Correlation coefficients were T-tested and are statistically significant. The elemental correlations, particularly those of logarithmic values of weighted sums and Bi, could be used as a gold path finding tool at Maldon. After a preliminary assay for gold and arsenic, only samples with As > 200 ppm should be assayed for other elements. Higher values of gold-correlated elements or elemental ratios, in samples with low gold grades, may increase confidence that gold is under reporting due to its highly nuggetty nature.CITATION:Krokowski de Vickerod, J and Ebsworth, G B, 2012. Correlation as a gold path finding tool at Maldon, Victoria, in Proceedings Narrow Vein Mining 2012 , pp 131-144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By I M. Platten, S C. Dominy

The Clogau St DavidÆs gold mine has a recorded production of around 81 000 oz Au and it is the largest mine in the Dolgellau gold-belt and BritainÆs most prolific historical producer. The original mine was first worked for copper, however; in 1854, gold was found in waste material from the St DavidÆs section. In recent times the mine has operated intermittently between 1983 - 2007. The principal black shale-hosted gold-bearing reef (Main Reef) can be traced for about 3 km, striking approximately NE-SW and dipping steeply between 60¦ - 90¦ SE. The reef system pinches and swells, changes strike and splits into a number of smaller branches. Reef width is variable, ranging from over 6 m to a few cm and in places reducing to small irregular blobs. The reef is internally complex and composed of swarms of narrow (1 - 300 mm) subparallel veins separated by country rock sheets. The gold-bearing veins within the reef package are discontinuous; though generally possess bonanza grades running 10s - 100s oz/t Au. It has historically been shown that some gold-rich vein segments can grade up to 300 oz/t Au. The predictability of the gold-rich segments is poor, but has been shown to be related to presence of the Clogau (black shale) Formation, and/or the mechanical interactions of the reef with greenstone sills, reef branching and splitting and/or cross-fractures to form ore shoots. The mine is currently being re-evaluated as a potential small-scale selective operation.CITATION:Dominy, S C and Platten, I M, 2012. Geology, mineralisation and potential of the Clogau St DavidÆs mine, Dolgellau gold-belt, Gwynedd, Wales, in Proceedings Narrow Vein Mining 2012 , pp 101-120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By G Morgan, C Kemp

In December 2010, a trial of borehole radar technology was conducted to test the usefulness of the technique in better refining the position and geometry of narrow vein orebodies away from the primary data sources of drilling and mapping of development excavations. This paper summarises the reasons why the technique was applied, describes the testing methods selected and summarises the outcomes of the trial.Poor reconciliations of recovered metal from a section of an orebody at Jundee mine site, Western Australia, led to an investigation that identified insufficient understanding of the geometry of a narrow vein orebody as a potential cause. This orebody was situated between mapped development excavations and away from surrounding drill holes. Borehole radar was identified as a possible technique that could supply information on vein location and continuity away from other data sources allowing more accurate orebody modelling and subsequent stope optimisation.A borehole radar instrument (10 - 100 MHz frequency) was inserted into pairs of purpose-drilled boreholes on either side of relatively well-constrained mineralisation and the radar reflection data was collected. This process was repeated in five locations across the mine to represent the most common geological settings, lithologies and orebody varieties encountered at Jundee to determine the suitability of applying the technique in each of these settings. Collected, processed and interpreted radar data was compared to other geology data collected independently for verification and interpretation.Conclusions drawn from the analysis were that the technique could effectively determine the following features of the mineralised veins in the majority of test environments: geometry of veins, magnitude of offsets where structures intersect and orientations of planar structures with short strike length. The technique was very useful in selecting the appropriate structural interpretation where available data could lead to multiple, equally likely, interpretations.CITATION:Kemp, C and Morgan, G, 2012. Using borehole radar to refine orebody interpretations in a narrow vein gold deposit, in Proceedings Narrow Vein Mining 2012 , pp 121-130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By S Hall

Mining schools around the world, many unfortunately now closed, were often established to teach the techniques of narrow vein mining and associated processing to students studying part-time while working in the industry. This arrangement ensured graduates (or æassociatesÆ) had a mix of skills and knowledge invaluable to the industry.It is argued that there is still a need to educate students in these narrow vein techniques and that there will be a growing demand for such graduates with a high level appreciation of this type of mining. There is also a need for innovation in narrow vein mining and processing to develop specific technologies and allow the use of techniques applied in æbulk miningÆ to achieve improvements in productivity, safety and economic performance.This paper aims to review the situation with regard to education and innovation in narrow vein mining.CITATION:Hall, S, 2012. Narrow vein education - back to the future?, in Proceedings Narrow Vein Mining 2012 , pp 23-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By P B. Hills, R J. Walton

Narrow vein tabular orebodies are prone to mining induced seismicity. The Tasmania Mine is a complex example of a seismically active tabular orebody, where the contrasting material properties of the host strata and of the orebody itself, serve to exacerbate the seismic response. Analysis of a continuous record of seismicity over a period of seven years has provided significant insight into the fundamental mechanics of the rock mass. Understanding seismicity to permit safe extraction of the orebody has been enhanced by instrumentation of rock mass behaviour in response to mining and mining induced seismicity. It is the purpose of this paper to explore that understanding in respect to the adoption of an alternative down-hole Avoca stoping method for use in particular circumstances.Intensive instrumentation of the Tasmania Mine over a period of four years has provided insight into the behaviour of the rock mass in response to extraction of the narrow vein orebody it encompasses. A range of instruments have been installed in clusters or single installations in order to measure changing stress conditions and the impact of those changes on the rock mass and the reinforcement system.Instruments are often installed in very close proximity to active production stoping. While it has been possible to observe the impact of the mining and mining induced seismicity at very close quarters, instruments installed in these locations are vulnerable to damage and consequently, the level of instrumentation is high. Instruments are continuously logged, typically on a six hourly basis coinciding with the end of regular blasting times. The response of the instrumentation to changed rock mass conditions is considered against the background of development and production blasting and against the seismic record to assess the viability of downhole Avoca stoping.CITATION:Hills, P B and Walton, R J, 2012. Continued observations of rock mass behaviour in response to stoping at the Tasmania mine, Beaconsfield, Tasmania, in Proceedings Narrow Vein Mining 2012 , pp 169-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By B Besa, E K. Chanda

It has long been recognised that narrow vein mining needs innovative approaches to mine access and mining methods in order to improve the economics of this vital part of the mining industry. The mining equipment used currently requires large openings in narrow vein-type deposits making mining operations uneconomical. In view of this and other shortcomings of the current mining practices, a study was initiated to investigate the potential of using low profile electric loader with mounted conveyor in conjunction with the electric monorail haulage system (EMTS) to load and haul the blasted material, particularly in decline development and main haulages. Computer simulation based on the General Purpose Simulation System/Henrikson (GPSS/H) is used to model the system and evaluate its performance. The results are compared with those for conventional mining using trucks and loaders. The EMTS provides competitive haulage rates in substantially smaller excavations than is currently achievable. According to simulation results, the electric loader in conjunction with the EMTS had the same number of blasts as the conventional system and hence the same advance rate of 3.33 m per 12 hour shift. Furthermore, the total drill-blast-load-haul cycle time was less than the conventional system by one hour.CITATION:Besa, B and Chanda, E K, 2012. Evaluation of low profile electric loader in conjunction with electric monorail haulage system in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 221-228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By J Hadjigeorgiou

Narrow vein mining, as most types of mining, faces important geotechnical challenges. The specificity of geotechnical challenges in narrow vein mines stems from the nature of the deposits, which are often inclined, discordant and found within fractured rock or faults or in shear zones within country rock. This complicates the construction of representative geomechanical models and limits the applicability of several engineering design tools. Furthermore, in certain cases, the severity of encountered geotechnical problems is considerably greater in narrow vein than in wider orebodies. This paper provides an overview of geotechnical and other challenges in narrow vein mines with a focus on how these are currently addressed. Of particular concern is the use of manual labour working close to the mining face where there is greater exposure to geomechanical hazards. This review concludes with a particular emphasis on understanding the limitations of commonly used engineering tools and techniques to address geotechnical problems in narrow vein mines.CITATION:Hadjigeorgiou, J, 2012. Geotechnical challenges in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By F Owusu-Mensah, F Nsarko

The Obuasi Mine has been in operation for the past 100 years. Within this period a host of mining methods have been employed during its various changing phases. The causes for the changes are multiple, ranging from orebody capability, dynamics, technology, safety, economics, production levels, geotechnical, etc. Mining methods applied have also ranged from timber square setts, conventional cut-and-fill, shrinkage stoping, sublevel caving, mechanised cut-and-fill, longitudinal and transverse open stoping, and lately longitudinal retreat mining method (LRMM).The Obuasi Mine has a world class underground resource potential of about 27 million ounces. A third of this is in reserve. The orebody is subvertical, with multiple lodes and with widths ranging from 1.5 - 40 m. It stretches along 8.5 km N/S strike. A cursory statistical analysis on the various resource ore widths show a higher percentage (60 per cent) of the resource being within the range of about 1.5 - 10 m. Thus a high proportion of the resource is amenable to narrow vein mining methods. This has enhanced the choice of LRMM as an alternative method. Also, with the increasing cost of mining over time, LRMM, which eliminates expensive and time consuming footwall drives, will become far more advantageous as compared to the transverse/longitudinal open stoping methods which currently constitute about 40 per cent of the total underground production.The LRMM currently delivers about 20 per cent of the Obuasi Mine production. Plans are underway to improve total underground production from the current average of 160 000 tpm to about >180 000 tpm in the next few years and about 20 - 40 per cent more in the foreseeable future. Recoverable ounces will also increase from 26 000 to about 34 000 ounces per month. The proportion of LRMM in the business plan is also expected to increase from the current modest level to about 50 per cent. Despite its tremendous advantages in terms of economics and productivity, the method is facing some challenges during its inception. The objective of this paper is to highlight some of the emerging challenges and their effect on production and offer possible remedies that could mitigate the current and possible future challenges.CITATION:Nsarko, F and Owusu-Mensah, F, 2012. The Obuasi mine - longitudinal retreat mining method application and challenges, in Proceedings Narrow Vein Mining 2012 , pp 59-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By K Rees

In the ideal world of an underground mining engineer, all narrow vein orebodies would be perfectly straight and continuous, thus would be a dream to mine. However, this is usually not the case. Narrow vein orebodies generally occur in association with shear zones and while shear zones do form linear trends, they most commonly preserve undulating expressions that need to be closely monitored, particularly when overprinted by post-formed structures. The surge in mines using fibrecrete as a primary form of ground support effectively reduces the time available for geological interpretation down to a 30 minute window between bogging and shotcreting. Thus, if the quality of the data collected is not up to scratch, then there is only a limited ability to reassess using 2D face photographs. To negate this, Xstrata Nickel AustralasiaÆs Cosmos mine has upgraded its data collection procedure. Geological information is now collected using photogrammetry survey, producing 3D images of the drive. Once created, the digital image of the drive is loaded into Vulcan, thus enabling geological interpretation to be carried out along entire drives, between levels and in association with all other data (eg drill holes, seismic data, etc). In addition to this, the 3D image can be used to accurately model the location of the ore, enabling stoping panels to be confidently positioned to maximise grade and minimise dilution. However, with the focus at Cosmos changing from narrow vein mining, to bulk mining methods in a more geotechnically complex terrain, the use of the 3D images has become paramount in understanding the structural geometry. Continual interpretation of the data has enabled drive profiles to be maintained through the increased use of ground support in poor ground and the redesign of development to enable optimal intersection of structures. Nevertheless, while the collection of quality data is important, it is only the effective use of the data, which enables significant gains in understanding.CITATION:Rees, K, 2012. The benefits of using photogrammetry in the geological interpretation of the Cosmos nickel mine, in Proceedings Narrow Vein Mining 2012 , pp 145-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By H S. Welideniya, K Ekanayake

Carbon rich graphite deposits found in Sri Lanka are of inorganic origin and they occur as narrow steeply dipping veins. The vein width of these deposits varies from a few centimetres to metres, with an average vein thickness of 1 m. It is believed that the carbon rich fluid intruded into fracture zones under high pressure and the temperature has crystallised into graphite. This process has also generated many minuscule graphite veins centred on main mineralisation, which has reduced the host rock overall rock mass rating. These discontinuities could also be considered as joints with graphite infill. Graphite mining at Bogala Mines, Sri Lanka is a unique example of narrow vein mining faced with numerous wall stability issues resulting from weak graphite infilled joints.The Bogala vein type graphite orebody has an average vein width of 1 m. Overhand cut-and-fill mining method is used for stoping. The stope consists of two boundary winzes for material handling, access and ventilation. Mining is done on the strike of the vein and the average mining slice height is 2 m. A void to the height of one mined slice is left below the mining level during mining. Waste rock resulting from vein blasting and mine development is dropped into this void as fill rock. Any void height left greater than a single slice height will increase stresses in the stoping zone. This will increase formation of rock blocks and their effective separation from wall rocks. Split miniscule veins occurring around main mineralisation intensifies rock block formation in an environment of mining induced stress release. Consequently, any rock blocks sliding into stopes on graphite infilled joints will behave under constant normal stiffness (CNS) conditions and their shear strength will converge rapidly towards remoulded shear strength of graphite alone. Unlike with general infill deposited in joints, graphite has a very low friction angle and with its slippery nature, a small thickness may affect in great deal to reduce joint shear strength.In addition to immediate filling of excavated voids, controlled vein blasting and spot bolting have improved mine safety. Furthermore, rock bolts connected to each other through iron plates and anchored to anchor bolts installed in non-fractured solid rock are practiced to stabilise rock falls and wedge failures in narrow vein graphite mining. These practices have significantly contributed to safe mining without any rock bursts and catastrophic failures.CITATION:Welideniya, H S and Ekanayake, K, 2012. Challenges faced by narrow vein graphite mining and influence of graphite infill on wall stability, in Proceedings Narrow Vein Mining 2012 , pp 71-76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By B M. Wilson, B J. Turner, S Sinclair, R J. Buerger

The Trident Gold Deposit is centred on the historical Higginsville Mining Centre, between the world class gold centres of St Ives (+15 Moz) and Norseman (+6.5 Moz) in Western AustraliaÆs productive eastern goldfields. It lies towards the southern end of the Norseman-Wiluna Greenstone belt in the Archaean Yilgarn Craton. The current in situ resource for Trident is estimated at 840 000 ounces, with production to date in excess of 500 000 ounces.Trident is hosted primarily within a thick, weakly differentiated gabbro with subordinate mafic and ultramafic lithologies and comprises a series of north-northeast trending, shallowly north plunging ore zones. The deposit comprises two main mineralisation styles; thin, lode-style, nuggety laminated quartz veins (Athena and Artemis) that formed along major shear zones primarily at the contacts between the various mafic and ultramafic lithologies; and large wallrock-hosted ore-zones comprising sigmoidal quartz tensional vein arrays and associated metasomatic wall rock alteration (eastern zone, western zone and Apollo) hosted exclusively within the gabbro.The thin laminated quartz vein lodes are important to the Trident Gold Deposits production profile as they constitute 33 per cent of the metal from only 14 per cent of the tonnes. The delineation, grade estimation and extraction of these lodes require a disproportionate amount of geological and engineering input due to the small scale variability in width, grade and direction. Over time, a robust and thorough process has been developed at the Trident Gold Deposit to understand and then successfully mine these complex mineralised systems.CITATION:Sinclair, S, Wilson, B M, Buerger, R J and Turner, B J, 2012. The mining industry needs to be shaken and stirred, in Proceedings Narrow Vein Mining 2012 , pp 155-166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By J. T. Carlson

Dolomite [CaMg(CO3)2] is an intolerable impurity in phosphate ores, due to its MgO content. The need to develop a cost-effective method for the removal of dolomite from high-MgO phosphate ores becomes increasingly important as high-grade reserves become depleted. The jigging process has been investigated as a method for the beneficiation of phosphate ores. A laboratory-scale jig was constructed and tested using a semicontinuous, ?through-the-screen? jigging process. Two types of sedimentary phosphate ore were used; a sample from Plant 1 in the 4.00 x 0.85-mm size range, containing 1.55% MgO, and a sample from Plant 2 in the 3.40 x 0.85-mm size range, containing 3.07% MgO. These were tested, using previously optimized jigging parameters, at high and low feed rates. For the Plant 1 phosphate ore, a phosphate concentrate that contained 0.89% MgO was achieved with a bone phosphate of lime (BPL) recovery of 32.0%. For the Plant 2 phosphate ore, a phosphate concentrate that contained 1.38% MgO was achieved, with a BPL recovery of 74.7%. Minimum achievable MgO grades were also determined by analyzing hand-separated phosphate samples.

Feb 1, 2012

By N. Chow

The recovery of manganese from lower-grade resources has been studied for a number of years. Of key importance in prior work was the discovery that higher-valent manganese can be readily leached with sulfurous acid. This eliminates the need for high-temperature reduction roasting that is conventionally used in processing high-grade material. High-temperature roasting is energy intensive, emits a large amount of carbon dioxide and would not be economical for processing lower grade material. While the prior work provides important information for extracting manganese from lower-grade resources, the production of unwanted byproducts and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems that to this point have precluded commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low-cost, environmentally friendly manner. The emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted byproducts.

Feb 1, 2012