Search Documents

By A. Ghirian

Once cemented paste backfill (CPB) is transferred and placed into a mine stope, various coupled mechanisms will take place in the CPB material or structure. It will be subjected to strong coupled thermal (T), hydraulic (H), mechanical (M), and chemical (C) processes. Field studies have shown that the in-situ properties and performance of CPB differ from those obtained in the laboratory. This is mainly due to effects of the aforementioned coupled THMC mechanisms or processes. For a reliable and cost-effective design of a CPB structure and barricade, it is crucial to have a proper understanding of the THMC behaviour and evolution of CPB. Also, it is important to consider the effect of coupled THMC factors (e.g., self-weight pressure, drained/undrained and thermal conditions, pore pressure) while curing the CPB specimens. For this purpose, a laboratory setup is developed to investigate the properties of CPB materials. The setup is capable of curing CPB specimens (10 cm in diameter and 20 cm in height) under controlled vertical pressure (curing under stress) and various coupled THMC conditions, while continuously monitoring the evolution of total stress, pore pressure, suction, temperature, water drainage, chemical composition of the pore water and vertical deformation. Once the required curing time is achieved, the specimen can be extracted and then subjected to experimental tests of interest, such as those that determine the Unconfined Compressive Strength (UCS), shear strength parameters, saturated hydraulic conductivity and thermal properties. In this paper, we describe the developed experimental setup and present some results of the THMC behaviour of CPB under various curing stresses and rates of backfilling. The obtained results show that the THMC properties of CPB are strongly coupled due to several mechanisms, such as self-weight pressure, heat of hydration and suction development as a result of self-desiccation. The findings can assist researchers and practitioners to better understand THMC behaviour and thus design more cost-effective CPB structures.

Aug 1, 2013

By K. Esmaieli

The Synthetic Rock Mass (SRM) approach has the potential to capture the mechanical behavior of large rock samples. In order for the method to be used with confidence it is necessary to gain a good understanding of the factors that influences its analysis. This paper reports on a series of numerical experiments, based on field data from a large underground mine, to investigate the influence of intact rock mass strength of a constructed (SRM). A jointed rock mass defined by three fracture sets was simulated by a Discrete Fracture Network (DFN) model. The generated fracture network was subsequently embedded into six different intact rock samples, simulated by a bonded particle model in PFC3D, generating six SRM samples. Each intact rock sample was 7 m × 7 m × 14 m and assigned different mechanical properties. The first intact rock sample was assigned a uniaxial compressive strength of 205 MPa and an elastic modulus of 104 GPa with the UCS and elastic modulus values of the other samples downgraded by 10% until the weakest sample had a UCS value of 121 MPa and an elastic modulus value of 61 GPa. All SRM samples were loaded under uniaxial compression to obtain the complete stress strain curve. It was observed that the compressive strength of the rock mass samples decreased by 10% following the same trend as the rock material strength. However, the elastic modulus of the rock mass samples decreased non-linearly with reduction of the elastic modulus of the rock material. The Poisson's ratio of rock mass samples does not change with decrease of rock material properties. For the post-peak behaviour the results show that both the brittleness index and the residual strength of rock mass samples decreased as the rock material properties degrades.

Aug 1, 2013

By M. Desjardins

The Hoyle Pond underground mine, located in the Porcupine Gold Camp, east of the city of Timmins, Ontario, Canada, is the cornerstone of Goldcorp Canada Ltd?s Porcupine Gold Mines. Cut and fill, shrinkage, longhole and panel mining methods are employed to excavate the narrow gold bearing structures. In order to meet increased flow requirements of 256 m3/s at the mine, a new Fresh Air Raise (FAR) and new surface fans were commissioned in early 2005. The newly acquired fans were capable of supplying the desired volume of air within a range of 1.5 and 2.0 kPa. Upon commissioning of the surface fans the total pressure was found to be exceedingly high; far beyond the design capabilities of the new installation. Consequently only one surface fan could be operated at any given time providing about half the required volume of air. Extensive work was immediately started aimed at reducing the system resistance in order to permit operation of the two fans in parallel and achieve the required mine flows. Larger booster fans were installed in parallel at the 900 m level, a 3 m raise bore linking the 450 and 900 m levels was developed to twin the existing fresh air circuit, and the FAR from surface to the 450 m level was twinned with the original FAR. This strategy, completed in 2012, resulted in a drastic reduction in system resistance and pressures, allowing the two surface fresh air fans to be safely operated in parallel and meeting the flow requirements. This paper describes details of the engineering design work and commissioning of the modified ventilation system, successfully ensuring the long term viability of the project.

Aug 1, 2013

By C. R. Tang

The respirable dust real-time monitoring equipment export information is complex, and electromagnetic wave wireless transmission is affected largely under mine conditions. The respirable dust concentration information transmission method based on led light equipment is proposed. The respirable dust concentration data of the individual real-time monitoring equipment is encoded to fit the system transmission; the encoded signal is modulated onto the LED mine lamp; the light signal is transmitted by the spatial channel; the signal is received by the receiver to the photoelectric conversion to restore the respirable dust concentration data for subsequent processing. Simulation and verification experiments showed that the respirable dust concentration information transmission method based on led light equipment can achieve the LED miners? lamps visible light wireless data transmission.

Aug 1, 2013

By H. Golzarpoor

Life Cycle Analysis (LCA) is a methodology for evaluating the environmental impacts associated with a product during its life cycle. LCA is identified as the most reliable method for verifying environmental impacts; however, current LCA-based approaches have certain limitations for environmental analysis of construction products. Integration of the LCA methodology with Discrete Event Simulation (DES) provides a sound framework for modeling and analysing the environmental impacts of construction products. LCA and DES is one possible combination for analysing the cause and effect of various scenarios where time, resources, and randomness of input variables affect the outcome and, therefore, has the potential to address the shortcomings of LCA in construction. Recent studies in disciplines other than construction such as manufacturing systems have revealed positive effects on evaluation of environmental metrics while integrating LCA with DES; however, this integration has not yet been applied for environmental analysis of construction products. By implementing LCA data in a DES model, this research proposes an environmental model of earthmoving operations in a case study. Environmental variables are simultaneously assessed with production variables in the same simulation model and the integration of DES and LCA is discussed.

Aug 1, 2013

By E. Brzychczy

Artificial intelligence techniques are ever more frequently implemented in the modern world. One of their numerous uses is supporting enterprise management. Intelligent techniques and intelligent information technology (IT) systems can be implemented in mining-related issues as well. The author of this article concentrates on supporting the process of planning mining operations by intelligent systems and techniques. The author also underlines the importance of knowledge accumulation in a mining enterprise (especially tacit knowledge) as well as its efficient storing and using. Additionally, the author provides a short description of characteristics of intelligent IT systems and indicates their capabilities in planning mining operations. She presents two solutions, namely: an advisory system which supports the process of planning preliminary works and exploitation works in hard coal mines, and a method of modeling and optimizing mining operations. Finally, the author indicates a few possible future development trends of intelligent systems - the intelligent systems of decision support.

Aug 1, 2013

By Amir Zavichi

Today, with the necessity of timely, on-budget and high quality completion of projects, proper use of construction equipment is essential to ensure project success. Construction equipment places a large monetary burden on the project and if not utilized efficiently, it can result in economic losses. Cranes are one of the most important and expensive operational devices on construction sites. They play a central role, and often activities that rely on crane services fall on the project?s critical path. Currently, material-handling scheduling is done by the crane operator or by an on-duty superintendent using his/hers personal judgment, making the process manual and timeconsuming. Thus, developing an optimal schedule, which considers different dynamic constraints in construction job site, may not be possible based on the current practice. This leads to longer operation times and a negative impact on project cost. This paper presents the latest results of an ongoing study, which aims to design and implement a nearreal time crane operation decision support system to be utilized directly by the crane operator or as an aid for the superintendent in scheduling optimal operation services. This system has several advantages such as maximizing the efficiency of crane operations, guaranteeing the best operation possible to reduce the crane?s travel time, reducing crews and equipment idle time, and minimizing the dependence on subjective human judgments.

Aug 1, 2013

By M. Uszko

The paper presents the conditions for determining the selection of methods for methane drainage in Polish hard coal mines. Various factors for the evaluation of methane drainage performance are used, including the methane drainage effectiveness ratio. However, as will be discussed there are limitations to the methane drainage ratio approach resulting from the characteristics of the deposits extracted in Kompania Weglowa S.A. coal mines.

Aug 1, 2013

By Yutaro Fukase

Various types of service robots have recently been developed for guarding facilities, caring for the elderly, carrying objects, and cleaning buildings. As barrier-free facilities improve and their use expands, these robots have more space within which to move inside buildings. Yet robots that move autonomously rely on position-detection systems. Though improving rapidly, these systems are far from perfect in determining positions in certain situations, especially when robots navigate large areas or cross various locations. Our group is working to solve this problem by developing a position-detection system using random-dot patterns on a floor. First, we construct a floor with a random-dot pattern and register the positions of all of the dots into a database. As the robot moves across the floor, a camera on the robot captures an image of the floor beneath it and crops the dot pattern in the image. The cropped dot pattern is matched to the dot patterns in the database to determine the position of the robot and the direction in which the robot is facing or moving. In this paper we propose a self-localization system and matching algorithms derived from a space technology and present the results of several experiments.

Aug 1, 2013

By L. Yaun

In underground coal mining operations, gas content in a coal seam is used to assess the risk of coal and gas outbursts. To estimate the gas content, a number of systems have been developed, however issues remain about the rapidness and accuracy of these systems. To address these issues, a new and improved system has been developed that includes a sampling-while-drilling unit for coal sampling, a coal canister, an underground-based portable measurement unit, a surface-based measurement apparatus, and gas content calculation software. The system has been successfully applied in underground coal mines at Huainan, China. This new, rapid and accurate system, its main components and field trials are described in this paper.

Aug 1, 2013

By X. Wu

Tunnel Boring Machines (TBMs) are widely used for tunneling in urban areas because of their high advance rate, precise as-built profile and minimal impact to buildings and traffic on the ground. For a tunnel built by a TBM, there are strict requirements on alignment control and safety. To meet these requirements, it is important to monitor the position of the TBM. In the current practice, the TBM position data, including advance distance and line and level deviations, are reported manually to the managers on a daily basis. To interpret and analyze the position data, the managers also need to refer to various construction drawings. This practice is untimely, inefficient, and error prone for decision making. To improve the current practice, an automatic approach for real-time as-built tunnel product modeling and visualization is proposed, based on TBM position and orientation data autonomously sourced from the Virtual Laser Target Board (VLTB) TBM Guidance System developed at University of Alberta. Related information of the tunnel project, such as the as-designed alignment, soil layers, the ground, existing utility lines, is also visualized together with the model of the as-built tunnel. The modeling algorithm is presented step by step. Its application in a real-life drainage tunnel project is discussed and limitations are also identified.

Aug 1, 2013

By V. V. Zubkov

The systems of geophysical monitoring have been already put into operation at coal mines and ore mines. Since at present it is rather difficult to conduct mine experiments; it is necessary to start a new step in joining of geomechanics and seismic. The linking geomechanical and geophysical monitoring at coal mines and ore mines today became possible due to progress in development of numerical methods of modeling of stress state and technology for processing of seismic information. This paper describes one potential step in linking geomechanical and seismic monitoring at coal mines and ore mines.

Aug 1, 2013

By F. Vahdatikhaki

Simulation techniques have offered significant boosts toward a cost-and-time-optimized planning of construction projects by enabling project managers to effectively comprehend the behavior of projects. Using historic data from projects of like nature, simulation considers uncertainties involved in a project through accommodating the stochastic modeling parameters. However, the heavy reliance on the statistical data and not taking into account the context-specific features of the project cause the degradation in the realism and accuracy of the simulation models. Similarly, the extent to which a historic pattern could be retrofitted to new projects will decrease in line with the growing uniqueness of the projects and the novelty of construction methods. Furthermore, the existing real-time simulation frameworks are not capable of distinguishing the transient environmental changes, with minimal long-term impacts on the productivity, from the influential changes that will greatly impact an operation. In addition, existing simulation tools are devoid of location awareness, resulting in the inability to consider safety threats in their representation of the project. To address these issues, this research proposes a framework based on the integration of new tracking technologies used in Automated Machine Guidance (AMG) with simulation-driven 4D modeling methods. The proposed framework automates the adjustment of the simulation model based on the updated data from the site, and thus transforms simulation from a predictive tool used at the planning phase to a proactive monitoring platform usable throughout the planning and construction phases. A prototype is developed to test and demonstrate the effectiveness of the proposed approach.

Aug 1, 2013

By Du Xinfeng

The resource quantity of the low rank coalbed methane (CBM) accounts for 47% of the total resource quantity of CBM in China. Compared with the exploration and development of the high rank CBM in Qinshui Basin, China and the low rank CBM in Powder River Basin, USA and Albert Basin, Canada, the exploration and development of the low rank CBM are still in the initial test stage. In this paper, on the basis of analyzing the mining geological conditions such as that the Huanglong Jurassic Coalfield is largely situated in the hills and gullies zones, and the coal reservoir has the features such as the low metamorphic degree, large coal seam thickness, simple coal matrix texture, high permeability and small CBM content and so on, it discusses the key technologies such as the development pattern of CBM, well location arrangement, drilling and well completion technology and fracturing technology and so on. It indicates that the underbalanced drilling and the cavity well completion based on the reservoir protection will be the development directions of the CBM development technology in this area.

Aug 1, 2013

Induced microseismicity monitoring is: ?Essential tool in improving the geotechnical understanding about a mine and its inaccessible surrounding rock masses. It helps to determine: -Event timing, location, and magnitude - identification of highly stressed areas -Event source mechanism - the physics of fracturing in its seismic source region -Seismic strain-rate distribution in 5D - identification of stress concentration or migration patterns -Geomechanical interpretation - identification of hidden geological structures or weaknesses in the ground -Strategy for mining e.g. by a block caving method - maximization of mine production and to optimize ground support design -Potential of future seismic hazards -Large event re-entry protocol, to improve mine safety ?The norm as part of mine safety maintenance and long-term mine design practices

Aug 1, 2013

By B. R. Rakishev

When transferring from the railway transport to the combined automobile-conveyor transport by stripping works at coal mines, it was proposed to form at the working zone a concentration horizon for reloading part of the stripping volumes at the railway transport. The procedure is adduced for substantiating parameters of bloc-panels, depending on the step of transferring of reloading points in interrelation with the intensity of the working zone?s development with observing the balanced movement of parts of the stripping zone relative to the temporary concentration level.

Aug 1, 2013

By W. Abdellah

Underground mine developments, such as haulage drifts and cross cuts, play a vital role in providing access to ore extraction areas for mine production. The stability of mine developments is thus of crucial importance during the life of a mine plan. Many Canadian mines use longhole mining methods or one of its variants. These methods require access to the orebody through mine developments such as haulage drifts and cross cuts on multiple levels. This paper examines the stability of mine development access intersections with respect to the planned mining sequence. A case study, the #1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario, is presented. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) was created for a development intersection situated 1.5 km below ground surface. The stability, or performance of the intersection, is evaluated in terms of the strength-to-stress ratio. The ratio threshold is set at 1.4 for temporary openings. Unsatisfactory performance is defined as a strength-to-stress ratio less than this threshold value. The performance of the intersection stability is evaluated at various modelled mining stages and the probabilistic method of analysis is then invoked to study the probability of unsatisfactory performance of the intersection. The results are presented and categorized with respect to probability, instability, and mining stage.

Aug 1, 2013

By A. Grimod

Rockfall drapery systems are commonly used as a simple, fast and cheap measure against the rock falling trajectories affecting very steep slopes. The system basically consists of a steel mesh, which is held on the top edge with a longitudinal cable fixed by means of a suitable number of anchors. The effect of this kind of intervention is to control the falls of the rocks, which are driven toward the bottom with slow velocity, or are stabilized on place. It can be used on any kind of slope to protect sensitive target in the mining industry, roads and railways, and inhabited areas. The falling blocks, typically smaller than 0.6 - 1.0 m in diameter, pile up into a trench (or into a ?pocket of mesh?) at the bottom. In comparison to other types of rockfall interventions, the simple drapery is cheaper, and its maintenance is easier, but on the other hand it cannot be considered the remedy for shallow instabilities, because it can only mitigate the effect of the falling trajectories. The design of simple draperies requires the analysis of several factors like the slope features (height, gradient, morphology), the geological and dynamic features (nature of the ground or rock, type of instability, erosion problem, blocks size), the environmental condition (presence of vegetation, aesthetical problem), the installation problem (accesses to the slope, safety for the workers, safety for the surrounding areas) and finally the performance required (temporary or permanent intervention, required maintenance, cost). Finally the most problematic design-step is the choice of the suitable mesh, the top longitudinal cable, and the top anchors type. Because of the highly variable nature of rockfall behaviour these structures cannot be standardized, but they have to be analyzed and designed for each case. Maccaferri has developed a new software application (MacRO 2) has a practical tool to define the mesh and the related supporting structure composed by up-slope cable and anchors. The software, based on the approach proposed by Muhunthan B. et al. (2005), allows designers to verify the top longitudinal cable, the anchors, and the mesh drapery, and to plan for maintenance procedures. Even if the method seems quite simple and rough, it is effective and lets the designer correctly foresee the materials and the geometrical features to be used on the interventions. This paper analyses the condition for the simple drapery installation, the main steps for the calculations, and it will present a case study in a U.S. mine. Nevertheless, even if the software allows a quick and simple calculation approach, onsite observations are always recommended in order to achieve a good design, with the ultimate goal of protecting property and human lives.

Aug 1, 2013

By R. Blazej

Machinery Systems Division (MSD) in the Institute of Mining Engineering at Wroclaw University of Technology specializes in belt conveying systems analyzing, calculating and design. Within the division operates the certified Laboratory of Belt Transportation (LTT) and Laboratory of Rollers. Since few years, a group of several people have begun work on developing a comprehensive system for the automatic evaluation of condition of conveyor belts working in the mines. Group uses both magnetic devices developed by specialized companies servicing belts and its own machine vision system developed for assessment of belts covers and edges during belt movement (up to 7 m / s) on the specially designed for this purpose the test conveyor. Recently they have got the research grant funded by the National Centre for Research and Development (NCBiR) for development of the system for automatic diagnosing of conveyor belts? condition and aiding of rational belt management. On the basis of previously created diagnostic tool called ABCDE (Automatic Belt Condition Diagnostic Equipment) the five modules: vision-A magnetic-B, preventive-C, forecasting?D, and determining safety factor-E will be developed. They will automatically interpret data about conveyor belts? condition to indicate the extent and timing of repairs, to prevent failures and to select the optimum moments for their replacements. The system will use results of ongoing research & development and planned research concerning modeling of belt wear using evolutionary genetic algorithms. The reached stage of research can not yet allow to start the implementation work by potential users. It is therefore necessary to pursuit research in real scale, the development of new modules (C-E) and intensive testing of the system in working condition with system calibration to optimize the economic effects.

Aug 1, 2013

By William Gleason

There was a time, not too long ago, when the most daunting challenges facing those in the mining and mineral processing industries could be solved through better technologies and better practices. But now the challenges that come from the actual acts of mining and processing are just part of the bigger picture. SME?s Colorado Section of the Mineral Processing Division (MPD) hosted its 63rd annual meeting at the Broadmoor Hotel in Colorado Springs, April 25-27 and, while the conference had its fair share or mineralolgy and processing presentations that were heavy on the technical side of things, this year?s conference was also focused on the issues of permitting, regulation compliance and legislative issues. The so-called ?softer? issues, that, if not addressed, can lead to very real and very hard challenges. Under the theme ?Mine your own business - permits, startups, expansions and resources,? even the most dedicated metallurgists were drawn into the discussions of politics and legislation, and how those issues affect their business. Fittingly, Colorado Mining Association (CMA) president Stuart Sanderson was honored with the Arthur C. Daman Lifetime Achievement Award. Sanderson, an outspoken proponent for the mining industry in Colorado and beyond, also presented the keynote address to the lunch crowd where he spoke about framing public opinion toward mining and the efforts of the CMA to move the public opinion dial in a direction more favorable to mining. Sanderson explained that Colorado, once a Republican stronghold, turned after 2002 and now is controlled by Democrats who are traditionally less supportive of the mining industry. Sanderson said the deciding factor in the power shift was money, as supporters of Democrats outspent Republicans in the most recent election cycles. CMA has done its part to keep mining going in the state with a broad marketing campaign that was outlined by Sanderson.

Aug 1, 2013