Search Documents

Resolution Copper Mine is planned to be a 2000 m deep panel cave mine with virgin rock temperatures above 80°C in rock with a high crystalline silica content. The planned run-of-mine production rate is 120 kt/day. The project is in prefeasibility evaluation. This paper discusses features of the ventilation system design, which include multiple ventilation shafts with total flow of about 3000 m³/s and both surface and underground refrigeration systems with more than 140 MW total capacity. This will be a very challenging mine to ventilate, but this work has demonstrated that it will be technically achievable with the application of existing technology.

Jan 1, 2014

By Andrew J. Brennan, Jonathan A. Knappett, Lewis Hamilton, Michael J. Brown

"Abstract This paper investigates the compressive behaviour of screw piles in sands and the key design parameters which control this. These types of foundation elements have typically been used as screw anchors onshore (i.e. for their tensile capacity), but there is increasing interest in their potential use as compression piles for supporting offshore marine renewable energy (MRE) devices (e.g. wind and tidal turbines) in deeper water. For such foundation applications, the compressive capacity is as important as the tensile capacity and is not well understood, particularly in cohesionless soils which are a likely seabed condition in MRE applications. A 1-g laboratory study was initially conducted on small scale model screw piles in sand beds of various relative density between 25 – 88%. These experiments were used to validate a Finite Element (FE) model having a stress-dependent constitutive model, making it useful for future up-scaling of the pile size for field applications. Following validation, the FE model was used to conduct a parametric study on the effects of flange spacing ratio (s/Dflange) and flange to shaft diameter ratio (Dflange/Dshaft). By using a validated FE model for this study, it was possible to observe the failure mechanisms (through the shear strain distribution) within the soil and correlate these with the pile capacity. This information was then used to comment on the most optimal (cost-effective) pile design for supporting compressive loads. This study represents a key step towards producing design tools appropriate for the design of screw piles in MREapplications.IntroductionAs defined in this paper, screw piles consist of a central small diameter hollow steel shaft, around which thin circular steel flanges run. Their principle of operation is that the flanges are spaced so as to trap the soil between them, thereby acting as an equivalent solid pile of the outer flange diameter, with a fully-rough ‘shaft’ interface (as shearing is soil-soil). One of the most important design decisions relates to the spacing of the flanges – if the flanges are spaced too far apart, then the soil will not be effectively trapped and the pile have a lower axial capacity and stiffness (controlled by the shaft friction along the central shaft and the bearing resistance arising from the individual flanges; If the flanges are spaced too close together, then there are potentially flanges which are not contributing to the pile capacity, therefore making the pile more expensive than it needs to be."

Jan 1, 2014

By H. E. Bartlett

Previously, the grade of ore at the shaft head was taken to be equivalent to the grade measured in the faces by means of chip sampling. The tonnage mined from the stopes is determined from survey volumetric measurements. Estimates of shaft head grade and tons include the grades and tons of waste, development ore, sweepings from old areas, and other sources, not all of which are sampled. The tonnage of ore delivered at the shaft is often estimated using skip factors. These factors are subject to manipulation and not all the skips are filled to the same level. Consequently, both the grade and tonnage of ore delivered at shaft head are subject to a measure of uncertainty. For many years, these uncertainties have led to disputes between shaft managers and metallurgists over the reconciliation between shaft tons and grade and plant tons and grade. These problems are compounded when several shafts feed a central processing plant. Shaft bonuses and a shaft?s profitability are affected by poor gold allocation methods. Without measurement of the grade and tonnage from all shafts, a poorly performing shaft could benefit at the expense of the other shafts. In order to improve the measurement of grades and tonnage at the shaft head, which is the custody transfer point between the mine and surface operations, South African mining companies have developed a methodology to measure the mass of ore from each shaft using rail weighing equipment, and the run-of-mine grades delivered from each shaft using cross-stream (go-belt) sampling. Harmony Gold Mining Company has implemented the rail weighing and go-belt sampling methods for their shafts. This paper deals with the statistical tests on the procedures and control measures that are in place to establish confidence in the gold allocations. The metal accounting system for examining the allocations follows the first principle of the AMIRA P754 Metal Accounting Code of Practice namely ?The metal accounting system must be based on accurate measurements of mass and metal content. It must be based on a full check-in check-out system?. The check-in is mass and grade of run-of-mine ore and the check-outs are the plant input grades and the recovery and residue from the plant. The balances between check-in and check-out are the subject of the statistical analyses, which have been conducted using the classical statistical tests and procedures that are generally used in all fields of endeavour. It is concluded that the gold allocation procedures that rely on go-belt sampling and rail weighing of ore from shafts has been successfully implemented, and that the system, which has been in operation at Harmony since 1993, has won general acceptance from stakeholders, with the gold allocations being perceived as being fair to all. Apart from the on-mine issues of bonuses and fair allocations, accurate metal accounting assists in the broader issues of generating accurate production figures for management. An added benefit of weighing and sampling ore at the shaft head has been that shafts now have daily moving average grades, which are used for grade control. The go-belt sample at the shaft head is the first accurate sample of production in the value chain from face sampling to gold bullion. Keywords metal accounting, go-belt sampling, run-of-mine sampling, codes of practice, AMIRA P754, train weighing, statistical analysis, gold split, allocation of gold, metal balance, grade control.

Jan 1, 2014

By R. S. Wang

The flotation of pyrite which be pretreated by electrochemical ways under external controlled voltages in different pH is explored. The floatability of pyrite is increased indistinctively after being pretreated in acidic and xanthate environment; Whereas, it is increased obviously between 400~800 millivolt in alkaline and xanthate condition. The reason for higher recovery of pyrite is that oxida-tion reaction, which results in S0 and S02, takes place on its surface, and that ethyl xanthate is oxi-dized into dixanthogen. In the meantime, the kinetics and mechanism is also studied.

Jan 1, 2014

By Marius Jacobs

"Safety performance in many companies and even industries has stalled in the few years. Accidents rates are at a "plateau" and yet, serious accidents and fatality rates are not. In more dramatic cases, such as in the BP Texas disaster, organizations that have "exemplary" safety statistics, suddenly have a catastrophic or multi-fatality event occurring. Other classic examples are the Piper Alpha disaster and NASA’s Challenger and Columbia disasters and even the Chernobyl nuclear reactor. Looking into the root causes of these accidents provides an insight into the events and deficiencies that led up to the accident, but what are the common features in the organization’s mindset? What characterizes these organizations’ decision-making, their approach to safety and to risk and are there specific cultural features that can be delineated? The research and review presented in this paper covers a period since 1994, which started in the Australian resource industry and since then covered international events. The features of these organizations are summarized as the seven deadly delusions, based on extensiveresearch since 1997 of organizations that suffered unexpected disasters.The Piper Alpha Oil Rig disaster in the North Sea, on the 6 July 1988, was one of the most pivotal events in safety around the world. It changed the thinking and focus of governments, whole industries and led to numerous books and papers. It resulted in new legislation, textbooks and a critical self-examination by the oil and gas industry.In short, an explosion and fire occurred when a pipe started leaking gas and ignited. A temporary flange, with no safety valve, was used to block off this pipe during a maintenance operation the previous shift. The permit to advise operators not to start the pumps on this line was misplaced and lost. Several deficiencies, problems and system failures coincided. A key factor was that the water deluge system was inoperable at the time and failed to extinguish the large fire that erupted, followed by an even larger gas explosion. The accommodation unit, situated on top of the oil rig, was the main "killing field" - most men gathered here to await instructions (which never came) and where they died from smoke inhalation. Later, a large explosion of the gas pipeline from an adjoined rig exploded and killed more people.The line of events and the associated system failures are all very relevant in the analysis of the accident, and provide the only insight into what caused the accident. But much "further back", inside the organization’s culture, lurks more dark matter. The first inclination is to ask what was "deficient" in the culture. Did they not care enough about safety, or about their people? Did they have a culture where production decisions were more important than safety considerations? Did they ‘coerce’ supervisors and employees to ignore safety precautions or did they just "fly by the seat of their pants"?Not surprisingly, it is very difficult to identify the true nature of the culture in that business because in such an aftermath of death and destruction, no one dare say that the safety culture was a ‘positive one, focused and caring’ or that the company was doing well in safety and that this is only a freak accident. Indeed, there were many deficiencies in the organization’s systems and procedures, such as the permit to work system.But there are some niggling questions: How is then that the Piper Alpha Oil Rig was actually considered the company’s most productive and safest oil rig in the North Sea? Why would this rig win a safety competition, 6 months before the disaster, with the deficient permit as its most outstanding successful system?"

Jan 1, 2014

By Gabriel Barrios, Juan Pérez-Prim, Marcelo Tavares

"The application of High Pressure grinding Rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits generally supporting this trend are better energy efficiency, improved grinding capacity, less sensitivity to ore grindability variations and higher metal recovery in downstream processes such as heap leaching and flotation. The HPGR machine comprises a pair of counter-rotating rolls mounted in a sturdy frame. One roll is fixed in the frame, while the other is allowed to float on rails and is positioned using pneumohydraulic springs. The feed material is introduced in the gap between the rolls and is crushed by the mechanism of interparticle breakage. Comminution performance is largely determined by the pressure exerted on the bed of particles by the floating roll hydraulic system. The operating bed pressure depends on the hydraulic system start-up parameters and the loading response of the feed material. The work describes how the coupling of the multi-body dynamic simulation with Discrete Element Method in which particle breakage is described using the particle replacement method, can be effectively used to predict the performance of the HPGR. The model considers important variables as the HPGR rolls geometry and design, the hydraulic spring system start-up parameters and the material loading response, to describe operational key outputs as material throughput, operating gap and roller pressure distribution. The preliminary version of the model has been used to predict the effect of material properties on the operating gap and the load distribution on the surface of the rolls, demonstrating that it can describe qualitatively the HPGR operation, indicating that the model will be a power full tool for the simulation and selection of industrial HPGR units."

Jan 1, 2014

By Tom Snyder, John Brulia

Part I is the first of a series of articles by the authors on hazardous materials (HM) transportation safety and compliance for shippers and carriers who offer and transport commercial explosives in commerce on public highways in the U.S.

Jan 1, 2014

During incineration of municipal solid waste (MSW), various environmentally harmful elements and heavy metals are liberated partly into bottom ash, and partly carried away with the off-gases and subsequently trapped in fly-ash. If these waste incineration residues are not properly processed and immobilized, it can lead to secondary environmental pollution to the air, soil and water. The stricter environmental regulations require a higher immobilization efficiency of the waste incineration residues, which is the main objective of the present cooperation research. Within the present project, a systematic scientific research on various MSWI residues has been carried out, including sampling, low or high temperature processing and leaching tests. In the present paper, the major results have been summarized. The research results reveal that through appropriate combined pre-processing and high temperature vitrification, the bottom ash and fly ash can be efficiently stabilized. The results achieved provide a valuable alternative route to treat the solid residues from incinerators, and to make efficient recycling and safe utilization possible.

Jan 1, 2014

By Cheng Xiang, Nan Ye, Xinyuan Ke, Yang. Jiakuan, Huabin Wang

Bayer red mud is a highly alkaline residue produced by the alumina industry through the Bayer process. Its disposal is a worldwide problem. The high alkali content and poor pozzolanic activity is aconstraint for its utilization on construction materials. In this study, the red mud was activated through an alkali-thermal method to improve its activity so that it can be utilized in geopolymerization. The red mud was mixed with different amounts of sodium hydroxide, and calcined under 800 °C to produce geopolymer precursors, and then mixed with water directly to prepare one-part geopolymer. X-ray diffraction was conducted to study the phase transformation of red mud and the mechanism of its geopolymerization. Nitrogen Isothermal Adsorption tests were conducted to analyze the pore structure of the geopolymer binders. The results show that calcinations with alkali would promote the Al in red mud transforming into glassy SiO2 to form the N-A-S phase which is soluble in water. When the red mud was calcined at 800 °C with a Na2O addition more than 10%, the dissolving of Si and Al from red mud was greatly improved. The thermal-alkali activated red mud with 10% Na2O obtaining a compressive strength of 9.77 MPa after it reacted with water and cured for 7 days at 20 °C and 95% RH. But the strength decreased as the curing time extended to 28 days. The reason is suggested to be that the polymerization of Al-O and Si-O is unstable due to the low Si/Al ratio of red mud. The alkali in the structure dissolves again into the pore water and corrupts the pore structure. Therefore, the thermal-alkali red mud should be combined with other reactive aluminosilicate materials such as granulated blast furnace slag to absorb the alkali released by the thermal-alkali red mud at the latter curing days.

Jan 1, 2014

By Masaki Kitazume, Yoshiaki Kikuchi

"Abstract Pile foundation is one of fundamental techniques to improve the bearing capacity and settlement characteristics of superstructures. Wide varieties of piles having various shape, size and material were developed and have been applied to a lot of construction projects throughout the world. The deep mixing method, an in-situ admixture stabilization method, was developed in 1970s in Japan and the European countries, and has been frequently applied to many construction projects for various improvement purposes such as increasing bearing capacity and horizontal resistance, reducing ground settlement, preventing liquefaction and so on. The design methods, execution procedure and quality control and assurance (QC/QA) of the method are standardized or specified in many countries. These standards, specification and/or technical manual have been a remarkable contribution to spread the techniques throughout the world. The QC/QA is one of the major concerns for clients and engineers who have poor or no experience of the technologies. In order to assure the high quality of deep mixing work in the global market, it is necessary to establish the concept of QC/QA and correlate the output of different procedures. Upon the request by the organizing committee of the DFI-EFFC International Conference on Piling & Deep Foundations, the authors conducted survey of the specifications and standards on the piling and deep mixing technologies in Asian countries. In this manuscript, the results of survey are briefly introduced by comparing these specifications and standards.IntroductionThe pile foundation is one of fundamental techniques to improve the bearing capacity and settlement characteristics of superstructures. Wide varieties of piles having various shape, size and material were developed and have been applied to a lot of construction projects throughout the world. The design method, execution procedure and quality control and assurance of pile foundations are standardized in many countries based on the accumulate research results, laboratory and field experiences. In Japan, steel pipe piles are mainly constructed by hammer driven in port construction. On the other hand, precast pre-stressed concrete piles or cast-in-place piles are mainly used in on land construction. When precast pre-stressed concrete piles are constructed, piles are usually set by inner excavation method because of preventing noise and vibration problems. More than 50 years ago, noise and vibration problems had not been serious problem in Japan, but around 50 years ago, they became serious and now less noise and vibration construction methods are used for pile construction on land in Japan. In Asian countries, though piles used for construction have a lot of variety, precast pre-stressed piles are commonly used. In this report, execution controls of construction methods of steel pipe piles and precast concrete piles are mainly considered."

Jan 1, 2014

By Roberto Galery, Priscila Esteves, Braz Cardoso, Marcelo Stopa

"It was developed in this work a computational tool to aid in anomaly detection present in the operation of ball mills. The tool uses a torque estimator that is based on measurements taken exclusively in the drive motor. The ball mill equipment widely used in the mining industry has, inherent to its principle of operation, high energy consumption and low efficiency. These characteristics are accentuated when the mill operates outside the ideal conditions of velocity and loading. Direct measurement of these variables is extremely difficult because it requires the installation of sensors in moving parts of the mill. Thus, systems that can help monitoring the operating conditions and predict anomalies are useful because they contribute to improving the performance of the process, help to reduce the energetic consumption, wear on the mill surface and frequency of maintenance shutdowns. The detection strategy implemented in this work is based on the fact that operational anomalies such as an inadequate percentage of balls and incorrect angular velocity manifest itself as a change in spectral components of the torque signal in the mill driven by an electric motor. The mill torque was estimated by processing motor variables measured by sensors commonly used for control purpose and installed exclusively in the motor. The mill was operated at various fault operating conditions and signals from electric motor and vibration on the mill shaft were measured. The spectral components present in the estimated torque signal were then compared with signals from a vibration sensor in order to establishing a correlation with anomalous operation condition of the mill. The experimental results showed that the signals obtained has an excellent correlation with other variables obtained by direct measurement and have potential to be used to construct a system for automatic fault detection in the operation of ball mills."

Jan 1, 2014

By Adam Powell, Salvador Barriga, Matthew Earlam

"The inert anode is a key enabling technology for dramatic energy and emissions reduction in extractive metallurgy. In molten salts, the materials challenge is nearly insurmountable: the anode must conduct electrons at high temperature in a pure oxygen and molten salt environment. A solid electrolyte, e.g. zirconia, between the salt and anode removes the molten salt stability constraint, and can act as a container for a liquid metal anode. This can be liquid silver for oxygen-generating inert anodes, or several metals for natural gas-fueled anodes; it is possible to switch between these modes. The solid electrolyte brings several other benefits: it eliminates molten salt contamination of the anode gas, creates a reducing environment enabling low-cost steel vessels, increases current efficiency, and eliminates carbon contamination of the product. New developments presented here, including current collector and low-cost anode designs, amplify these benefits for producing aluminum, magnesium, rare-earths, and other metals.IntroductionReactive metals such as magnesium, aluminum and rare-earths play increasing roles in efficient transportation and clean energy. In response to new fuel economy standards, automotive OEMs are planning large increases in use of aluminum and magnesium to reduce vehicle weight. Rareearth permanent magnet motors and generators exhibit better power-to-weight and efficiency than induction motors and other designs, making this today's primary motor technology for hybrid and electric vehicles, and for wind turbines. Nickel metal hydride (NiMH) batteries with lanthanum are dominant in hybrids. In 2011, transportation comprised 28.6 out of 103.1 EJ of US energy consumption [1] and 1,845 out of 5,471 million metric tonnes (MMT = 109 kg) CO2e of US greenhouse gas (GHG) emissions [1], creating big targets for economy-wide reductions.Unfortunately processes for making reactive metals for these applications are very inefficient and heavily-polluting. In primary aluminum production, Hall-Heroult cell electricity use [2] is more than double the reaction enthalpy due to heat losses through frozen cryolite side-walls and anode gases, graphite anode plants add significant energy use and GHG emissions [2] (see Table 1). Magnesium is even worse: silicothermic reduction by the Pidgeon process in China produces about 85% of the world's magnesium using coal or coke gas [3]. Chloride electrolysis begins with high-purity MgO and requires carbochlorination or hydrochlorination and costly chloride dehydration [4]—rendered unnecessary for aluminum by the Hall-Heroult cell. Production of neodymium and lanthanum with graphite anodes leads to inconsistent carbon content: small cells make 1 kg batches for analysis, sorting and sale by carbon content, with very high labor and analysis costs. And vertical electrodes give no incentive to reduce anode effect: some reports indicate that China's rare-earth metal industry emits more CF4 and C2F6—with global warming potential (GWP) 6500 and 9200 times CO2 respectively—than China's aluminum industry [5]."

Jan 1, 2014

By P. A. Crane, N. Shirley, Aung Moe, H. M. Nicholson, D. Kan

Kazakhstan’s first commercial copper-leach solvent extraction-electrowinning plant, Central Asia Metals’ Kounrad project, was commissioned in April 2012. Exploiting low grade waste stockpiles produced during Soviet era open pit mining, a 10,000 tpa copper cathode plant was designed, constructed and commissioned within 18 months. Overcoming initial challenges with a workforce unfamiliar with the technology and with extensive periods of sub-zero conditions during winter the project has consistently met targets and produced high quality copper cathodes at cash costs of less than US$1/lb. Challenges encountered during the first two years of operation are described and future plans briefly discussed.

Jan 1, 2014

By Qiuyang Hong, Bo Li, Dongyun Liang

"A weathering-crust niobium-rare earth-bearing deposit is formed by the weathering alterationof alkaline granite, which is refractory due to its low grade and complex properties. The mineralogicalcomposition of ore, the grain size of majorminerals as well as the occurrence of Nb and REE are studied in this paper using MLA combined with traditional methods. According to the results, a wide range of Nb-Ti-REE compound minerals including titanoniobite, uranpyrochlore, chlopinite, samarskite and ilmenorutile areformed for the extensive isomorphous substitution among the elements of Nb, Ta, REE, Fe, Ti, U and Th. The occurrence of REE is extremely complex. First, the REEexistingas rare earth minerals including monazite, xenotime, bastnaesite,etcaccount for 21%. Second, the REEexist in the lattice of Nb and Zr minerals as isomorphous additions, which account for 18%. Third, the REE exist as colloidal rare earthdeposit,which account for 35%. Last, the REEexistingas ion-adsorption-type rare earth,which are adsorbedon the kaolinite in the form of hydrated hydroxyl ions, account for 26%.Based on the results of mineralogy, the combined technology process "mineral processing- hydrometallurgical separation" is needed to deal with the ore. The mineral processing tests show that, for the feed ore containing Nb2O5 0.065%, REO 0.13%, an Nb-REE concentrate containing Nb2O5 1.38%, REO 1.98% can be gained by "high intensity magnetic separation-regrinding-gravity separation by shaking tables". The recovery of Nb2O5 and REO is 62.42% and 44.78% respectively. The Nb-REE concentrate is dealt by the metallurgy process "direct reduction- acid leaching & acidulating- neutralization & precipitation- chlorination & distillation" and the rare earth oxide of 92.34% REO as well as the Nb-Zr oxide of 24.62% Nb2O5 can be obtained with the recovery of REO and Nb2O5 being 76.83% and 59.37% respectively."

Jan 1, 2014

By Y. Nakamura, T. H. Okabe, S. A. Sunkar, K. Nose

Ruthenium (Ru) is known as a platinum group element with a very small production volume. In fact, the worldwide annual production of primary Ru metal is only about 20-30 tons, and it depends on the amount of Pt produced, since Ru is a byproduct from Pt smelting. The primary uses of Ru are as a material for resistors, as a catalyst for electrode materials, and as a sputtering target for hard disk memory storage. In order to recover Ru from the spent sand-blasting abrasive media generated during the cleaning of the apparatus used for Ru sputtering, a hydrometallurgical recovery process using hypochlorite solution has been investigated. In this study, various types of recycling processes that are presently under development are also introduced, and their features and differences are discussed. The advantages and disadvantages of the new recycling processes are evaluated, and the possibility of establishing new recycling processes in the future is discussed from a multilateral perspective.

Jan 1, 2014

By G. Jenny

The particle size distribution of ground minerals is of decisive importance for downstream processes like floatation, separation, drying or others. In order to optimize the process efficiency on one hand and the final product quality on the other hand an early control of the grinding or classification stage is essential. The ultrasound based particle size analyser OPUS is capable of performing on-line particle size distribution (PSD) and solid content measurement of mineral slurries such as iron ore, copper ore, fluorspar, or quartz sand and alumina directly in heavy and rough process environment. The instrument provides a PSD of 31 size classes and can be applied for particles from nanometer range up to several millimetres. Arbitrary interpolations in between the 31 measured points are available. Typical residue values show an excellent agreement to off-line particle size analysis methods such as e.g. sieve analyses or laser diffraction. OPUS is designed as rugged in-line probe made from stainless steel. The applied technique is independent of product flow dynamics, contamination, optical properties, vibrations, pressures or changes in solid concentrations. The instrument provides all data on the system?s PC or on the process control system by a variety of interfaces.

Jan 1, 2014

By N. Aslin, R. Clark, G. Heferen

The methods of harvesting copper from stainless steel mother plates has been investigated from fundamental and operational experience perspectives. At least five different harvesting techniques have been identified that have different effects on product quality, current efficiency, current distribution, growth morphology and ease of stripping. Each method is examined from fundamental principles to understand what occurs during the harvesting process and why the particular effects are manifested. Experience from plants operating the harvesting method is provided to show that the fundamental understanding is relevant. Best practice harvesting method and harvesting management are described.

Jan 1, 2014

By Yuanyuan Wang, Yuhao Ding, Hao Bai, Kang Zhou, Guangwei Du

"In this paper, the list analysis of GHG emissions of aluminum industry was conducted based on the data from typical electrolytic aluminum plants of a China’s northwest province. The results show that under the conditions of average anode effect coefficient as 0.16 times/(cell• day) and anode duration as 5 minutes per day, equivalent emissions of CO2 reached 1.23 ton per ton of aluminum, in which PFC emissions accounted for about 71%. Compared with foreign advanced level, which is 0.87 ton per ton of aluminum under the conditions of average anode effect coefficient as 0.01 times/(cell•day) and anode duration as 0.46 minutes per day, there is much room for China’s aluminum industry to reduce GHG emissions. Since anode effect plays an important role on PFCs generation in electrolytic aluminum process, how to control anode effect strictly becomes the key factor for remarkable reduction of GHG emissions in China’s aluminum industry.IntroductionTechnology of aluminum electrolysis is a mature and efficient process of aluminum production. Due to the huge demand on aluminum worldwide, so resource consumption, energy consumption and pollutant emissions in the process of aluminum production are still large. The global output of aluminum reached 45193 kt in 2012. A large amount of CO2 and PFCs are produced in the process of aluminum production, and the greenhouse effect and environmental pollution caused by emissions of them is a concern. PFCs belong to a powerful greenhouse gas, thus emission reduction of PFCs is very important for aluminum electrolysis industry. At present, China's aluminum production accounts for about 33% of the world's aluminum production, and controlling PFCs emission has become the key point of pollution control of aluminum electrolysis industry in China [1].Taking the case of a typical electrolytic aluminum plant of a China’s northwest province, this paper studies the list analysis of GHG emissions of aluminum industry in China. GHG emissions of a China’s northwest province were calculated through investigating existing situation of aluminum electrolysis industry in the province, knowing capacity, output, main production technology and equipment level of aluminum electrolysis industry, and using the calculation framework and methods of GHG emissions of aluminum electrolysis industry, which were put forward by the intergovernmental panel on climate change (IPCC), the international aluminum association and other organizations at home and abroad. The list analysis of GHG emissions of aluminum electrolysis industry will offer useful information in promoting emission reduction of GHG in aluminum electrolysis industry, improve the efficiency of energy utilization."

Jan 1, 2014

By Andy L. Shaffer

A novel liquid settlement system (LSS) was installed in advance of mining at a western United States (U.S.) longwall mine to measure total roof sag from the time of cutting to days after mining during gate road development. The system was used to compare differences in roof sag between conventional place-change mining using a Joy continuous miner and a Fletcher roof bolter and mining using a miner-bolter. The LSS was installed with an intrinsically safe, miniature data acquisition system (MIDAS) to record roof response at four locations in the same gate road. The system utilized pressure transducers to measure roof sag by the principle of falling head (fluid pressure) in fluid-filletubes installed in the immediate roof. Details of the LSS design, installation, data collection, post-processing, and future applications are discussed.

Jan 1, 2014

By N. Nehoroshev, P. Solozhenkin, N. Voyloshnikova, A. Pshennikov

"Molecular modeling of clusters of major bismuth minerals, Bi2S3, was carried out whereby molecular models of minerals and reagents clusters were created. Their HOMO and LUMO energy levels were calculated and using known modelling equations, the absolute hardness ?, eV and electronegativity were calculated. The charges of separate atoms of clusters and the change of properties of the minerals were determined which allowed predictions of the flotation properties of raw ores containing rare bismuth minerals. Modeled complexes containing the clusters of minerals and various collectors were constructed, consisting of atoms and bonds within clusters of minerals. Major physical and chemical parameters were determined for the complexes created, including the total and electronic energy. Based on the energy calculations, predictions of the collector efficiency were proposed. The efficiency of collector was established for various thiolic reagents, the compounds of phosphorus (III) and mixtures of reagents. Theoretical results were checked and confirmed against laboratory ore flotation tests. A gold-bismuth-magnetite ore type was studied where gold, bismuth and iron (magnetite) are of industrial interest. The ore contains 2.8 g/t Au, 1.0 g/t Ag, 0.26% Bi, 45% Fe and 1.25% As. Sulphide mineralization can be mainly found in the form of pyrrhotite, pyrite and arsenopyrite. Bismuth can be mainly found in the form of bismuthite and native bismuth. Gold is fine. A flow sheet for Zhelezny Kryazh ore treatment was proposed. This flow sheet consists of grinding to 95-98% -74 µm, sulfide flotation with two cleaner with xanthate addition, cyanidation of flotation concentrate and flotation tailings included treatment with with CaO (6 kg, 6 hours), cyanidation (8 hours) and CIL (8+24 hours). Saleable products are gold doré, bismuth and iron concentrate."

Jan 1, 2014