Search Documents

By Tianming Sun, Gabriella Tranell, Ragnhild E. Aune, Mark William Kennedy

Rare Earth Elements (REEs) are critical for the production of many advanced materials and products. Mining and primary production of REEs are generally associated with significant environmental impacts. By recovery of REEs from secondary sources, through recycling or as a byproduct, the adverse environmental impacts may be partly avoided. In the present study apatite concentrate originating from iron ore beneficiation done by LKAB in Kiruna, Sweden, is explored as a possible source for REEs. The composition and distribution of the REEs within the concentrates are studied using ICP-MS, XRD and SEM-EDS/EPMA, as well as the melting point and heat of fusion using DTA-TGA-MS. The behavior of the material during melting has also been studied through wetting and slag saturation experiments. The overall aim of the study is to evaluate the implications for future smelting experiments aimed at concentration and recovery of the REEs.

Jan 1, 2015

By ZHANG Ting

In view of the high consumption and contamination of traditional vanadium extraction technology, a new process of leaching the converter vanadium slag without roasting with titanium dioxide waste was proposed. Extraction mechanism of P204 in the leaching solution had been researched and single factor experiments show that after a prereduction of Fe, and under conditions: ambient temperature，leaching solution original pH=2.5, phase ratio (A/O)=1:3, shaking time 8min, the extraction rate of V is more than 98.62% meanwhile the separation rate between V and Fe is up to 135.3 in the 20%P204-10%TBP-Sulfonated kerosene extraction system.

Jan 1, 2015

By Jose Carlos D’Abreu, Edelink Efrain Tinoco Falero, Mauricio Marcos Otaviano, Helio Marques Kohler

Nowadays the most important Direct Reduction - DR processes in shaft furnaces has to deal with carbon fines precipitation and DRI carburization issues. Based in a cooperative research program joining Catholic University (PUC-Rio) and SAMARCO Mining Co, a project dealing with pellets reduction and those two phenomena was established. This work analyzes kinetically the three reactions mentioned before, considering typical values for the operational variables temperature, flowrate, pressure and gas composition, parameters commonly used to control the DRI formation in the Reduction Zone - RZ of the shaft furnaces. From laboratories experimental results, the kinetic equations for those reactions were established and, using the superposition principle, generated a specific global kinetic model for the iron oxide reduction and the soot formation. Finally, using those experimental results and applying a planned statistical factorial analysis for the experiments, the numerical coefficients for each equation were calculated and the correlation factor determined for the proposed global kinetic equation.

Jan 1, 2015

By Ruiling DU, Jiazhi Zhang, Yong Zhao, Keng Wu

Reaction kinetics of metallurgical physical chemistry which was successfully applied in metallurgy (as ferrous metallurgy, non-ferrous metallurgy) became an important theoretical foundation for subject system of traditional metallurgy. Not only the research methods were very perfect, but also the independent structures and systems of it had been formed. One of the important tasks of metallurgical reaction engineering was the simulation of metallurgical process. And then, the mechanism of reaction process and the conversion time points of different control links should be obtained accurately. Therefore, the research methods and results of reaction kinetics in metallurgical physical chemistry were not very suitable for metallurgical reaction engineering. In order to provide the definite conditions of transmission, reaction kinetics parameters and the conversion time points of different control links for solving the transmission and reaction equations in metallurgical reaction engineering, a new method for researching kinetics mechanisms in metallurgical reaction engineering was proposed ,which was named stepwise attempt method. Then the comparison of results between the two methods and the further development of stepwise attempt method were discussed in this paper. As a new research method for reaction kinetics in metallurgical reaction engineering, stepwise attempt method could not only satisfy the development of metallurgical reaction engineering, but also provide necessary guarantees for establishing its independent subject system.

Jan 1, 2015

By QIE Jun-mao, DONG Fang, DENG Hao-hua

The DIL402C thermal dilatometer and STA449C thermal analyzer were employed to test the linear expansion and contraction coefficient，CP and DSC curve of 304 stainless steel. The result showed that the linear expansion coefficient range was 20.9700×10-6～21.5712×10-6 and the linear contraction coefficient range was 21.2528×10-6～21.9471×10-6.The linear expansion and contraction coefficient were higher than other steel grade，so the 304 stainless steel belonged to the crack sensitive steel. Because of the crystal phase transformation occurred during the 1000~1400 ℃,the curve of CP fluctuated obviously and the defects of casting blank occurred easily. Chosen 1414℃ as the liquidus temperature of 304 stainless steel based on the analysis results of DSC. The curve of DSC was unsmooth during 1450～1100℃，the crystal phase transformation occurs and thermal stability of slab was inferior.When the initial solidified shell formed in this temperature range,the thickness of the shell would be nonuniform and the surface defects occurred more easily.

Jan 1, 2015

By Yi Tan, Kazuki Morita, Yaqiong Li

Molten Si-Al alloy, with the addition of Sn, was used for metallurgical grade Si purification by a low-temperature solidification method, with the aim of improving the recovery rate of Si. In this ternary melt, bulk Si was grown with a planar front by a directional solidification process under a well-controlled thermal gradient and growth rate conditions, thereby reducing the contamination of solvent metals. Effects of cooling rate, amount of Sn addition, and temperature gradient on the quality of bulk Si were determined. The criterion for constitutional supercooling for single-phase growth from multicomponent melts was employed to evaluate the growth process.

Jan 1, 2015

By Huimin Lu, Liyuan Zhao, Zhijiang Gao

The aluminum matrix composite reinforced by graphene was successfully fabricated using high pressure torsion (HPT). With only 0.5wt% graphene, the grain size was reduced to 100nm while that of pure Al was about 500nm. The hardness of the composite increased from the center (64HV) to the edge (120HV) of the sample. Moreover, the tensile strength of this composite reached 197MPa, while that of pure Al was 157MPa. The enhancement in mechanical properties was induced by grain refinement, load transfer from the matrix to the reinforcement and dislocations piled up at the grain boundaries.

Jan 1, 2015

By Antoine Allanore, Guillaume Lambotte, Bradley R. Nakanishi

Current industrial methods used for rare earth element (REE) extraction involve: 1) ore enrichment, 2) separation of rare earth oxides (REOs), 3) chlorination or hydrofluorination, and 4) individual electrowinning of REEs from a molten halide electrolyte. The complexity of REE extraction is inherited from their electronic configuration. Recently, molten oxide electrolysis (MOE) has been used to produce reactive metals directly from their oxides, e.g. titanium. As a single-step alternative to processes 3) and 4), or laboratory has investigated rare earth extraction by MOE. A key challenge is to find a molten electrolyte more stable than REOs. One possibility is to use binaries of REOs directly as a solvent. We have, therefore, developed two experimental approaches for studying molten REOs at temperatures exceeding 2200oC. The present work reports the most recent experimental results obtained with La2O3-Y2O3. Those promising results demonstrate potential for operating with molten REOs and refine the underlying materials challenge for electrodes to enable metal recovery.

Jan 1, 2015

By Min Chen, Lei Xu, Weijun Huang, Shuai Zhang

For the purpose of extending the service life of MgO-C bricks used as linings of vanadium-extraction converters, the effect of Fe addition on properties of MgO-C bricks was investigated. The results showed the addition of Fe could effectively improve the sinterability of the oxidized layer of the MgO-C refractory at 1400°C due to the effect of FeO (formed by oxidation of Fe) on formation of MgO-FeOss and modification of the microstructure, and excellent corrosion resistance against vanadium containing slag was also obtained due to the increase of compactness of the oxidized layer and concentration of FeO in the oxidized layer. Consequently, it is considered that MgO-C brick by introducing the new phase of Fe is a favorable substitute of MgO-C refractory to be used as linings of vanadium-extraction converters.

Jan 1, 2015

By Junli Xu, Xianwei Hu, Kaiyu Xie, Liangxing Li, Zhongning Shi, Zhaowen Wang, Bingliang Gao, Aimin Liu

Al-Ti master alloys were prepared by aluminothermic reduction between the dissolved titanium dioxide and aluminum in cryolite melts at 960oC. The kinetic analysis by differential scanning calorimetry indicated that the apparent activation energy of the reaction of reducing titanium dioxide by aluminium is 22.3 kJ/mol, and the reaction order is 0.5. The products were analyzed by means of X-ray diffraction, X-ray fluorescence, scanning electron microscopy and energy dispersive spectrometer. Results from X-ray diffraction showed that the phase compositions of produced alloys are Al and Al3Ti. In addition, Al-Ti master alloys containing 2-6 mass% Ti were formed at different reduction time of 2-5h in aluminothermic reduction experiment.

Jan 1, 2015

By Baozhong Ma, Qian Li, Yonggang Wei, Shiwei Zhou, Bo Li, Chengyan Wang, Hua Wang

The magnesium-rich nickel oxide ore (w (Ni) =1.09 %, w (MgO)=29.08 %) mixed with 6 % and 8 % anthracite were roasted at different temperatures. XRD and SEM/EDS techniques were utilized to characterize the phase and microstructure transformation of the ores. The results show that lizardite and chrysotile of raw ore were converted into forsterite and enstatite during reduction roasting process. Simultaneously, iron and nickel oxide were reduced and migrated from the initial magnesium silicate. Fe3Si were formed when the roasting temperature went up to 1300 ℃ and 1350 ℃, and a small amount of Ni was observed in it. Temperatures got too high were not benefit to the polymerization of ferronickel.

Jan 1, 2015

By Kexin Jiao, Zhijia Zhang, Jianliang Zhang, Zhengjian Liu

Carburization behavior of molten iron in blast furnace is an essential part of BF long campaign technology. Maintaining carbon content stable is an important prerequisite to ensure the high production of the blast furnace. In this paper, the important aspects of the research progress which mainly including the study of iron carburization at the upper and the lower parts of the blast furnace was reviewed. Indirect carburizing is the main way at the top of the blast furnace. The content of carbon in metallic iron increases with the reducibility of iron ore improved. The thermodynamics and kinetics conditions are good for carburization reaction to take place at the bottom of the blast furnace. Carbon content of molten iron increased by coke carburizing. Meanwhile, the drawbacks of the existing literature on iron carburization behavior were analyzed and new research directions of iron carburization were proposed in the future.

Jan 1, 2015

By Pedro A. Netto, Giulio R. Altoé, Sergio N. Monteiro, Ygor M. Moraes, Frederico M. Margem, Gabriel O. Glória

Since environmental issues are becoming more and more important Worldwide. Nowadays, Natural fibers are been used to substitute the synthetic ones. Although PALF fiber is an important natural fiber and its mechanical Properties surpass in various aspects some other lignocelluloses fibers, such few studies have been conducted with the fiber obtained from leaf of PALF plant. In order to better evaluate the mechanical properties and possible applications, this paper aims to improve the elastic modulus of the PALF fiber by Weibull statistics, by evaluating their mechanicals properties and possible applications. The fibers were divided in diameter intervals and the tensile strength and elasticity modulus were measured in each range. The fractured surface was examined using scanning electron microscopy. The results, interpreted by the Weibull statistical method, showed a correlation between the fiber elastic modulus and its diameter.

Jan 1, 2015

By Yuanbo Zhang, FENG ZHOU, Guanghui Li, Zhengwei Yu, RuijunWang, Tao Jiang

Composite agglomeration process (CAP) of iron ore fines has been proved an effective route for ironmaking burden production, and is characterized by low the fuel consumption and high the productivity compared with the traditional sintering process. Sintering behavior of pelletizing feed in CAP has not been studied fully yet. In this study, individual pellet and simulated CAP cells were roasted under the simulated sintering conditions. The compressive strength, FeO content and microstructures of roasted samples were investigated. The results show that pelletizing feed either from magnetite ore hematite concentrate can be indurated under the conditions of conventional iron ore sintering. Hematite pelletizing feed has better sintering property than magnetite pelletizing feed. Pelletizing feed consolidation in CAP cells is identical to the individual pelletizing feed, but the strength of CAP cells is much higher than the individual pelletizing feed. Higher basicity in both pelletizing feed and matrix feed is beneficial to the strength of CAP cells. Individual strength of pelletizing feed is not the decisive factor in CAP as the pelletizing feed has been embedded into the matrix with high basicity and formed an organic whole. The main chemical compositions and basicity of pelletizing feed and basicity matching with matrix feed is important.

Jan 1, 2015

By Jun Chang, Jin-hui Peng, Jing Chen, Li-bo Zhang

The leaching of indium from refractory zinc oxide flue dust(ZOFD) is attempted to utilize microwave sulfating roasting process, followed by water leaching. The ZOFD and roasted product were characterized by XRD and SEM/EDS analysis. The effects of various roasting parameters, such as roasting temperature/duration, the proportion of sulfuric acid, as well as the leaching parameters such as the leaching duration and liquid/solid ratio, were assessed. The results indicate that nearly 97% of indium could be leached under the following conditions: mass ratio of concentrated sulfuric acid to ZOFD to be 0.5, roasting temperature of 150 ℃ and duration of 1.5 hours; while the optimal leaching conditions hold at temperature of 25 ℃ for 1 hour, with 4:1 of liquid/solid ratio. The indium leaching rate by the microwave roasting increased by 8% as compared with the conventional roasting process under identical conditions.

Jan 1, 2015

By Guanghui Li, Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Xiaohui Fan, Zhiyuan Yu

With the increase of proportion of biochar(without modified) replacing coke breeze, the physical strength of sinter decreases due to the faster burning speed of biochar. An investigation upon passivating biochar with boric acid was then conducted to strengthen sintering in this paper. A layer of thin film of B2O3 distributed in the surface of biochar was observed, which could reduce the contact between reaction gas and biochar. So the burning speed of biochar was decreased properly after passivation, and the combustion efficiency increased due to the inhibition of carbon gasification. The comprehensive effects of above changes could increase the maximum temperature of sintering bed, which facilitated to the mineralization of sintering mixtures. Eventually sintering indices got reinforced. Thus the indices of sinter as applying 40% passivated biochar were comparable with that of 100% coke breeze.

Jan 1, 2015

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Army Research Laboratory (ARL) has an interest in the recovery and processing of rare earth elements. At Montana Tech, elevated temperature chlorination of rare earth oxides is presently being investigated as a potential methods leading to the selective separation and recovery of rare earth elements from mineral ores and concentrates. After preliminary evaluation, ytterbium oxide was selected as a representative surrogate material for more extensive chlorination studies. Methods used to determine the conversion and recovery include X-ray diffraction (XRD) and inductively coupled plasma (ICP) analysis. These data have been used to establish and confirm process conditions that consistently yield high conversion efficiencies. Based on the promising results, further experimentation is underway to ascertain the metallurgical response of other rare earth oxides and carbonates to the roasting process. The end goal is to create a robust process for industrial application that has greater efficiency and reduced costs as compared to current practice.

Jan 1, 2015

By Yanhui Liu, Xuewei Lv, Chenguang Bai

A thermodynamic model for determining the surface tension of molten slag by considering the surface tension and molar volume of the pure oxide component, and their ionic radii was extended to the slag bearing high TiO2 (varying from 80 to 67%) at 1973 K. The iso-surface tension curves for the FeO-TiO2-Ti2O3 ternary system at 1973 K are almost parallel to the FeOTi2O3 line. TiO2 plays a role of surface-active solute, and its surface-active effect is attenuating with increasing the TiO2 content. The iso-surface tension curve shifts away from the TiO2 corner, indicating that the surface tension of the ternary slag decreases along with the addition of SiO2. The reasons include the addition of SiO2 with lower surface tension and the decrease of the total ion moment at the surface. Both CaO and MgO can bring about that the iso-surface tension curve shifts towards the TiO2 corner, indicating that the surface tension of the ternary slag increases along with the addition of CaO or MgO. CaO has a more pronounced effect on increasing the surface tension of the ternary slag than MgO at an equimolar amount addition. The increase of the surface tension results from both the compositional change and the variation of the slag structure.

Jan 1, 2015

By Mingming Zhang, Marshall S. Coe, Marcelo W. Andrade

To supply iron units and flux burden in blast furnaces, sinter basicity is one of the vital parameters for sinter plants. The sinter basicity also plays an important role in sinter quality since it imparts the formation of different mineral phases in sinter. Pot-grate sintering tests were carried out with low and high basicity to investigate the effects of sinter basicity on sinter mineralogy, properties and productivity. It was found that with an increase in sinter basicity, both sinter productivity and reducibility (RI) increased. Tumbler index (TI) and low temperature degradation index (LTD) of high basicity sinter were comparable to low basicity sinter. Softening and melting tests showed that sinter with 3.5 C/S basicity had slightly higher softening temperature comparing to lower basicity sinter with C/S 2.6, acid and fluxed pellets. XRD analyses confirmed the formation of silico-ferrite of calcium and alumina (SFCA) and calcium ferrite (CF) in the tested sinter samples.

Jan 1, 2015

By Onuralp Yucel, Ahmet Turan, Murat Alkan, Hasan Ozer

SHS (Self-propagating High-temperature Synthesis) is one of the important methods to synthesize B4C powders. The process contains the reaction of boron oxide powders (B2O3) with magnesium reducing agent and carbon black carburizer. SHS products are leached in HCl media to purify synthesized B4C powders in the following step. In the present study, effects of various functional additives (KClO3, KHSO4, MgSO4.7H2O, NaCl, MgO and Na2SO4) in the SHS stage were carried out. Various proportions of the additives were mixed with the initial SHS charge mixtures. Two different molar ratios were employed in the initial SHS mixtures as 1:3:0.8 B2O3:Mg:C and 1:2.5:0.8 B2O3:Mg:C. After the SHS step, HCl leaching process was applied to the SHS products. Filter cakes were dried and characterized by using X-Ray Diffraction Spectroscopy, BET and chemical analysis techniques.

Jan 1, 2015