Search Documents

By Xiaozhu Chen, Qi Ping, Pu Yuan, Qinyong Ma

"In order to investigate the fractal feature of coalmine deep rock fragments under impact loads, variable cross-section split Hopkinson pressure bar apparatus, 50 mm in diameter, was adopted to conduct impact compressive test for rock specimens from -962m deep coalmine. Various impact pressures, such as 0.3, 0.6, 0.9 and 1.2MPa, were selected to implement different loading rates. Sieving statistical analyses were conducted for rock fragments after being impacted, and the particle size distribution of broken rock in various loading rates were calculated with the fractal method and then the corresponding fractal dimension was obtained. Test results shows that there is a good self-similarity and fractal feature in fragments distribution of deep coalmine sandstone under impact loads. The fractal dimension of fragments is between 1.9 and 2.7. The research also indicates that there is an approximate power relationship between dynamic compressive strength and fractal dimension, and a strength power relationship between fractal dimension and average strain rate. Moreover, there is a linear relationship between fractal dimension and specimen absorbed energy. The rock fractured process can be quantitatively described through fractal dimension, which can reflect the deep rock broken degree and is an ideal index to evaluate the distribution of rock fragments.INTRODUCTIONBroken rock is one of the most basic processes in mining operations, rock fragmentation has always been an important index to evaluate rock breaking effect (Xu & Yu, 1984). Macroscopic fragmentation of rock material is the final results of continuous development, expansion, gathering and cutthrough of internal micro-cracks. This process, developing from microscopic damage to macroscopic fragmentation, is an energy dissipation process and shows fractal characteristics (Xie, 1993). Turcotte (1986) has conducted statistical analyses of fragmentation for different kinds of geological materials under various broken conditions, and arrived at the conclusion that fragmentation distribution is a fractal."

Jan 1, 2015

By Boyd Davis, Brook Zaback

"Among the first published papers from Prof. Torstein Utigard was work on imaging the aluminum electrolysis process and in-situ measurements of aluminum in cryolite melts. He and Prof. Jim Toguri used an x-ray radiographic technique to measure interfacial tension of aluminum drops. Publications using this equipment for aluminum electrolysis spanned from 1985 to 2006. As well, other methods were used to better understand electrolysis in molten salts, including hot-stage microscopy, direct observations from above the bath and water modeling techniques. For chloride systems (for magnesium and lithium), it is possible to see side-on the electrolysis using a quartz cell. In honour of Prof. Utigard’s contribution to this field, this paper presents a summary of work on visualization of molten salt electrolysis, including work done at the authors’ labs and others around the world. The paper will summarize key findings and their possible impact on molten salt electrolysis."

Jan 1, 2015

By Sakellariou M., Ferentinou M.

Determination of the nonlinear behavior of multivariate dynamic systems often presents a challenging and demanding task. Therefore, complex geomechanics systems are an ideal area for the application of intelligent methods. Often the physical problem is controlled by nonlinear equations, conveying to the use of neural networks. Hudson, (1992a), aiming at efficient engineering modelling and design, introduced and developed Rock Engineering Systems (RES) approach, through the implementation of generic interaction matrix GIM. This approach has been used for a wide variety of rock engineering and other problems, resulting in many case studies available, which illustrate the application of RES to rock engineering problems. Considering the spectrum of the coding methods for the Generic Interaction Matrix, we suggest an objective coding approach. Among the five proposed coding GIM methods, the coding method according to the slope of Pi and Pj relation is relatively accurate, but it might be difficult or impossible to establish or estimate the exact relation of Pi vs Pj for most of the variables involved within a rock engineering system. Self organising maps, are a special type of unsupervised artificial neural networks, which can learn from complex, multidimensional data, and transform them to visually decipherable clusters. The proposed, coding of the GIM, is performed through the combined use of scatter plots produced through, (SOM), and the coding according Pi vs Pj slope. Naghadehi et al., (2013) constructed a database of worldwide experience, in open-pit mine slope stability, the selection of the principal factors was based on Hudson (1992a) who proposed an ‘atlas’ of factors affecting the stability of rock slopes. Slope classification was performed according to status of stability. The rating of the GIM matrix was completed, coupling scatter matrix produced by SOM training, and Pi vs Pj slope plot. Results refer to the identification of clusters, according to status of stability within the original multivariate data set, and the rating of the principal factors according to the dominance and interaction intensity within the open pit mines RES.

Jan 1, 2015

By M. A. Halim, V. I. Lakshmanan

Recycling is one of the key elements for sustainable process development for the recovery of value-added products and reducing environmental impact. Process Research ORTECH Inc. has developed several innovative and sustainable technologies, which minimizes the use of water, and chemicals for the recovery of gold, vanadium and gallium from secondary sources by maximizing the recycling of reagents, and reuse of water from process effluents.

Jan 1, 2015

By M. Deutsch, E. González, M. Williams

"Uncertainty exists in ultimate-pit limits due to geologic variation and unpredictable economic landscapes. In this work, we show how this uncertainty affects the ultimate pit and how it can be analyzed to improve the mine planning process. A stochastic framework using geostatistical simulation and parametric analysis was used to model the effects of geologic and economic variations on ultimate-pit limits and overall project economics. This analysis was made possible by a new pit optimization implementation that can be automated and set up to calculate ultimate pits for hundreds of different scenarios in a matter of hours. Quantifying ultimate-pit uncertainty early in the mine planning process allows mining engineers to make informed decisions regarding infrastructure placement and to mitigate the possibility of incurring substantial costs to relocate critical mine facilities. Resumen ¦ Existen dudas sobre los límites del pit final por causa de la variación geológica y lo impredecible de los paisajes económicos. En este trabajo les mostramos como esta incertidumbre afecta el pit final y como puede ser analizada para mejorar el proceso de planificación de la mina. Se usó un marco estocástico con simulación geoestadística de análisis paramétrico con el fin de poder hace la modelación de los efectos de las variaciones geológicas y económicas en los límites de pit finales y proyectos económicos en general. Este análisis fue posible gracias a una nueva implementación de optimización de pits que puede ser automatizada y configurada para calcular pits finales para cientos de escenarios diferentes en cuestión de horas. La cuantificación temprana de la falta de certeza en pits finales durante el proceso de planificación permite a los ingenieros de minas tomar decisiones informadas en lo que respecta a la ubicación de infraestructura y en la mitigación de posibles costos sustanciales por causa de la reubicación de instalaciones clave de la mina."

Jan 1, 2015

By C. Derek Martin

"Predicting the ground response for tunnels in weak shales remains challenging. Predicting the ground response is challenged by difficulties in characterising the material, and our ability to predict deformations that are driven by coupled hydromechanical processes, when this material yields. The techniques that are used for characterizing weak shales are reviewed, and three case histories are examined that demonstrate the behaviour of these weak rocks during tunnelling. A general framework is provided for assessing the squeezing potential for weak shales.1 INTRODUCTIONGeologically, shale is an argillaceous fine-grained sedimentary rock that forms from the compaction of silt and clay-size mineral particles commonly referred to as ""mud"". Because of this grain size, the material is generically classed as Mudstone (Figure 1). Shale is distinguished from other mudstones because it is made up of many thin layers (laminated) and readily splits into thin pieces along the laminations (fissile). While the geological classification of shale appears straightforward, the classification for engineering purposes is often confusing. Underwood (l967) provided the first description of shale that made the distinction between “soil-like” compaction shales and “rock-like ""cemented"" shales. He coined the term ‘clay shale’ to capture the characteristics of hard clay yet recognizing its origin as a shale. In this paper weak shale is synonymous with clay shale and have strengths that typically range from R1 to R2 (1 to 25 MPa). Characterising these materials draws on methods from both soil and rock mechanics."

Jan 1, 2015

By H. J. McQueen

About 1973 the abrupt decrease in crude oil shipments due to political action by Middle Eastern suppliers, caused a shortage and a steep price rise. In response, Canada had to develop strategies of diminishing consumption and increasing production in both traditional and environmentally friendly resources. To clarify the situation in Canada, there are brief histories of energy (discovery, pipelines), manufacturing and science development, 1800-1970. Energy strategies, both nationally and in Quebec, succeeded in curbing consumption and in expanding production while fostering research in renewable sources. The industry-sector committees provided free exchange of conservation techniques through the federal energy ministry, with progress reports issued annually. Pipeline history in North America is reviewed along with manufacture and construction plans in Canada. Considerable success in all the aspects provided long lasting benefits, but after the embargo was lifted, many research initiatives were gradually abandoned for political reasons. Sustainability is the goal; society must conduct conserver analysis, legislation and action to enhance it.

Jan 1, 2015

By Arístides Sotomayor

El presente texto señala el comportamiento del mercado nacional de cobre en el período 2000- 2013, donde se analiza la evolución de la producción minera metalúrgica a través de la identificación de las tendencias anuales en el mercado peruano.

Jan 1, 2015

By Da-Qiang Cang, Qingde Wang, Wei Wang, Wen-Bin Dai, Min Guo, Yu Li

Utilization of both slag and its heat for hot slag is a great challenge for iron and steel industry. Many methods of hot slag modification for directly converting hot slag into value-added materials were researched in recent years, and waste heat of hot slag could thereby be transformed into inner energy or chemical energy of the materials. In this paper, an experiment of converting hot slag directly into glass ceramics by hot slag modification method was conducted. A cooled modifiers mainly composed of fly ash were firstly heated though a cyclone furnace and then fell into a molten bath to mix with hot steel slag. Half of hot slag was used as raw materials and accordingly about half energy consumption, about 5MJ/kg for melting raw materials was saved in the process compared with that of traditional producing method. Frit quenched from the modified hot slag had a higher basicity of 0.6-0.7 than traditional frits in order to reduce the needed amount of cold modifiers and accordingly utilize more hot slag and its waste heat. Glass ceramics were further prepared from the frit and a heat treatment of one-stage method is more suiter to such frit than that of two-stage method. The glass-ceramics with basicity of 0.6 and heat-treated by one stage method had the best performance with bending strength of 146.46 MPa, Vickers hardness of 6.79 GPa, water absorption rate of below 2% and shrinkage rate of around 10%.

Jan 1, 2015

By William Gleason

"It is safe to say that the coal industry, in the United States and globally, is currently suffering through one of the hardest times in its history.A perfect storm of competition, changing energy demands, politics and public perceptions have collided, inflicting significant harm to the industry that many say is irreparable. This, in turn, has led to massive job losses in some regions, heavy cuts in production and even bankruptcy filings from two of the largest coal mining companies in the nation.Cheaper natural gas can certainly take a large share of the blame for the struggle of coal, as utility companies switch from coal to natural gas for power generation. According to the U.S. Energy Information Administration (EIA) the amount of coal used for electricity generation in the United States is at a 45-year low.November 2015 marked the fifth consecutive month that natural gas was the leading source of power generation in the United States. EIA said generators produced 101,866 thousand megawatt hours (MWh) of electricity with gas in November versus just 87,789 thousand MWh with coal, the lowest monthly level since May 1980 when monthly coal use was 84,884 thousand MWh.According to Robert Godby, director of the Center for Energy Economics and Public Policy at the University of Wyoming, there are a number of factors playing a role in the decline of coal, but he points to the advances in fracking as the tipping point.“A lot of people will argue that regulation is the cause of the decline, and it has played a part, for sure, but the story of the recent past is more about what competition has done to the energy market,” Godby told Mining Engineering. “The war on coal was originally declared by natural gas in 2008.”The price of natural gas, which was at $13 per million Btu before the gas fracking boom, has fallen to as low as $1.68 in December 2015. Likewise, Godby said the cost of wind generation is now lower than the cost of generation from coal and the cost of solar generation is coming down as well. In addition to that, the demand for energy has changed in the past five years with more efficiencies in everything from building design to lightbulbs."

Jan 1, 2015

By K. Hanumantha Rao, A. Javadi Nooshabadi

"Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by chalcopyrite (CuFeS2), which is a copper iron sulfide mineral, during grinding, was investigated. It was observed that chalcopyrite generated H2O2 in pulp liquid during wet grinding and also in the solids when placed in water immediately after dry grinding. The generation of H2O2 during either wet or dry grinding was thought to be due to a reaction between chalcopyrite and water where the mineral surface is catalytically active in producing •OH free radicals by breaking down the water molecule. The effect of pH in the grinding medium or in the water in which solids are added immediately after dry grinding showed that the lower the pH value, the higher the H2O2 generation. When chalcopyrite and pyrite are mixed in different proportions, the formation of H2O2 was seen to increase with increasing pyrite fraction in the mixed composition. The results of H2O2 formation in pulp liquid of chalcopyrite and together with pyrite at different experimental conditions have been explained by Eh-pH diagrams of these minerals. This study highlights the necessity of revisiting the electrochemical and/or galvanic interaction mechanisms between the chalcopyrite and pyrite in terms of their flotation behavior.IntroductionHydrogen peroxide causes nonselective oxidation of sulfide minerals if present in pulp liquid. Oxidation of sulfide minerals takes place when they are exposed to atmosphere and during the grinding process when the particle size is reduced for flotation. The oxidation of chalcopyrite leads to iron dissolution from the particle surface and from a metal-deficient, sulfur-rich surface (Fairthorne et al., 1997). Other studies report the formation of iron hydroxide on the surface with the metal ion dislodged on the surface (Buckley and Woods, 1984; Chander, 1991). The chemical reactions for the oxidation of chalcopyrite in alkaline and in acidic solutions with the addition of oxidants, such as oxygen or hydrogen peroxide, are shown in Eqs. (1) and (2), respectively (Shi and Fornasiero, 2010)."

Jan 1, 2015

By O. Hungr, V. Gischig, G. Preisig

Deep-seated landslides are characterized by slow time-dependent movements induced by constant gravitational creep, and periods of acceleration associated with stress changes within the rock and the preexisting fracture network. Natural stress changes are typically caused by seasonal variations in surface temperatures and groundwater pressures, but also by rare and more violent events such as earthquakes. These processes are responsible for cyclic loading and unloading that leads to rock mass damage, fatigue and progressive failure with time, and may explain sudden, unexpected rock slope acceleration phases. In this work, we present a set of distinct-element models to investigate and compare the role of hydromechanical fatigue and seismic fatigue in the history of a deep-seated landslide. Hydromechanical fatigue arises from the fluctuation of pore pressure in fractures accompanying periods of significant groundwater recharge. In alpine areas, there are usually one or two cycles per year associated with snow melt and intense rainfall periods. In the presence of a deep confined aquifer within the rock slope, the amplitude of pressure fluctuations may reach values of 0.25-0.5 MPa. Hydromechanical models considering such pressure changes are able to reproduce observed slope accelerations-decelerations phases. Substantial accelerations may occur even in the absence of a cycle of exceptional amplitude, depending on the current state of fatigue. At a given time, one or more fractures may be critically-stressed, and a small change in applied stress is enough to cause local failure and induce a crisis of enhanced slope acceleration. This is augmented if the rock slope contains planes of weakness associated with its tectonic history, glacial debuttressing, etc. The corresponding behaviour is analogous to laboratory experiments on rock and metal fatigue. Similar fatigue effects have also been proposed for repeated earthquake events in seismically active regions. Unlike hydromechanical stress changes that occur in a more localized portion of the rock slope, those induced by passing seismic waves involve the entire rock mass. Moreover, the frequency and amplitude of stress perturbations due to earthquakes are different than those induced by pore pressure variations, although both likely contribute in combination to the degradation and progressive failure of large deep-seated landslides when both are present. The results presented illustrate that: (1) assessment of slope stability near critical infrastructure (e.g., hydroelectric reservoirs) should not only consider static stability, but also failure mechanisms related to fatigue that evolve over time and may result in an apparently stable slope progressing towards a critical state due to relatively small but repetitive stress changes; and that (2) characterization of fatigue processes affecting a deep-seated landslide requires multiparametric continuous monitoring at different observation points.

Jan 1, 2015

By J. P. Piguet, A. Hosni, J. P. Josien, H. Baroudi, R. Hadadou

"The iron ore mines in the Lorraine region of north-eastern France cover a surface area of approximately 3,900 km2 and involve more than 150 cities. A total extraction method was usually used during exploitation, but this technique was sometimes replaced by the room and abandoned pillar technique when it was necessary to protect surface buildings and infrastructure. Rooms and abandoned pillars were initially designed to ensure long-term mine stability. However, this aim was not always reached and numerous collapses occurred in the Lorraine iron basin, either during production or several years after closure. Several subsidence events were identified during a period of one century; the most recent event occurred in 2012. Two groups of events were identified. The first group represents events characterized by sudden surface movement, and the second group includes event characterized by progressive subsidence.Numerous studies conducted during the last decade helped improve our understanding the origin mechanism of spontaneous or progressive (slow) events. These studies led to identifying long-term potentially unstable underground zones (hazard zones), particularly deep zones located under buildings and infrastructure. The latest are currently monitored by microseismic networks. A similar high requirement level is needed for unstable zones without taking into account the kinetics of the subsidence, which is very important for safety. Thus, GEODERIS initiated this study, primarily to acquire a better understanding of the kinetics of the progressive events group and identify the main parameters that could explain why some pillars zones developed a maximum amplitude subsidence on surface within a few hours or days, while it took several weeks to months for others. In practice, the results of this study will facilitate adapting the requirement level of microseismic monitoring system to the kinetics of pillar collapse.To retrieve the real kinetics for each event, historical and sparse documentation was used. Firstly, archives research was conducted, especially testimonies and newspaper articles published during the events. This work helped to gather useful information that sometimes contained a precise description of subsidence duration. The archives research helped to classify some progressive events according to the subsidence kinetics. Secondly, a diagnostic of geotechnical and geomechanical parameters of historic events was realized, combined with a cross analysis of the data. The analysis took into account dimensions of underground workings (e.g., pillar lengths, widths, heights, introduction of a “pillar shape factor”, and stress amount). An original expression was highlighted to connect the pillar geometry to the stress state. The kinetics expression was calibrated to classify the historic events taken into account according to the kinetics of movements. The kinetic criterion was applied to predict subsidence kinetics for the potential unstable zones currently monitored by a microseismic system."

Jan 1, 2015

By K. M. Wild, C. D. Martin, F. Amann

"Argillaceous rock formations, in particular clay shales, are notorious for creating challenges in rock engineering. Due to their generally low hydraulic conductivity and their complete saturation in their natural state at depth, the behavior of clay shales is usually characterized by a strong hydro-mechanical coupling.This paper presents typical pore pressure responses monitored in different underground rock laboratories and explores alternative ways for their interpretation. The underpinning processes and their relevance are identified based on analytical and conceptual numerical models. Pore pressure monitoring data from Opalinus clay at the Mont Terri Underground laboratory, the Boom Clay at the Mol facility and the Callovo-Oxfordian clay in the Meuse/Haute–Marne URL show a similar pore-pressure response associated with stress changes accompanying tunnel construction although the tunnels were built in different rock types, at different locations, and under different in-situ conditions.The numerical analyses in this study shows that the pore pressure response around an excavation in low permeable clay shales may have different explanations. Pore pressure drops observed in the tunnel near field can theoretically be explained by both, a pure elastic response in an isotropic or anisotropic rock mass with an anisotropic stress state, or a inelastic response and related dilatancy. However, a comparison between the numerical models and the in-situ measurements revealed that the latter is more likely. This conclusion is justified by the observation that pore pressure drops occur significantly ahead of the tunnel face which is not the case in elastic numerical simulations. Pore pressure measurements in the far field, where failure processes are unlikely to occur, can only partly be explained by a linear poroelastic models. The introduction of an anisotropic material plays a key role in reproducing the responses, conceptually."

Jan 1, 2015

By M. L. Free, N. Dhawan, M. S. Safarzadeh, J. D. Miller, M. S. Moats

"The drum agglomeration of nickel laterite and gold ores has been optimized through the design of experiments (DOE) using a Taguchi L16 (45) orthogonal array to determine the optimum conditions for maximizing average agglomerate size and minimizing the amount of fines. The effects of controllable operating factors including moisture content (nickel laterite ore: 34-37%; gold ore: 7-10%), retention time (2-3.5 min), drum speed (15-45% critical speed), drum load (nickel laterite ore: 8-32 %; gold ore: 6-22%) and acid concentration (150-600 g/L) on the performance of the agglomeration process were studied.For nickel laterite ore, maximum average agglomerate size and minimum percent fines (-1 mm) occurred under the following conditions: drum load (23.7%), moisture (36.5%), time (3 min), drum speed (30% critical speed) and acid concentration (150 g/L). Under the studied nickel laterite ore conditions, the most effective parameters for maximizing average agglomerate size and minimizing the amount of fines were found to be drum load and acid concentration, respectively. Drum speed had a statistically significant effect on minimizing the amount of fines. Maximum average agglomerate size and minimum percent fines (-1 mm) for gold ore occurred under the following conditions: drum load (19.3%), moisture (8.5%), time (2 min 15 s) and drum speed (40% critical). The most significant factors for maximizing average agglomerate size and minimizing the amount of fines for gold ore were found to be drum load, time and moisture.IntroductionSeveral heap leach operations have experienced problems in terms of poor recovery due to percolation issues caused by low-grade complex ores, tailings and clayey deposits. Poor percolation can lead to low metal extraction due to solution channeling or the development of impermeable/dead zones within the heap (Dhawan et al., 2012; Kappes, 2005). Improper heap building practices such as the use of loose agglomerates and inadequate attention toward the presence of clay minerals have been among the main reasons for percolation issues. During the transport of ore material, severe segregation of the material can occur. To overcome percolation problems, a major improvement was made through the introduction of agglomeration prior to ore placement. If the ore particles and agglomerates are of similar size, segregation can be avoided to a great extent (Dhawan et al., 2013; Kinard and Schweizer, 1987; McClelland and van Zyl, 1988). Agglomeration improves the uniform percolation of solution through ore heaps and is applicable to many ores, wastes and milled tailings (Bouffard, 2005; Dhawan et al., 2013). Manning and Kappes (2005) reported agglomeration/ stacking accounts for ~14% of the total heap leaching operating cost. The cost of binder is a primary contributor toward the total cost. Also, the lack of consistent quality control tests for agglomerate often leads to operational problems. The details are mentioned elsewhere (Dhawan et al., 2013). Considering the significant contribution of the agglomeration/stacking step toward the total heap leach operating cost, it is appropriate to study the agglomeration behavior and its optimization for two different ores. The reason to study the same parameters for different ores is the fact that significant variability in the agglomeration behavior of different ores has been reported to exist in industrial operations."

Jan 1, 2015

By Z. S. Shao, X. Z. Li

"Sub-critical crack growth plays an important role in long-term creep failure in brittle rock. Based on micromechanics established by using relationship between micromechanical wing crack growth model and macroscopic strain, and comparing theoretical model with testing results, a method, which applies the theory to real rock, is suggested in this paper. Using this method, properties of creep, damage and progressive failure in brittle rock are investigated. Effects of stress state on creep failure time and steady-state creep rate are analyzed and graphically presented. The results are helpful to support structure design and service life evaluation of underground structures with high geostatic stresses. INTRODUCTIONDuring the long-term operation in underground space with brittle surrounding rock, due to chemical action between pore water and rock, the failure of rock often occurs at stresses below its short-term failure strength, which brings serious effect on the long-term stability of underground structure. Thus, the long-term strength of brittle rock attracted wide interests of scholars around the world. The static fatigue limit was predicted by exponential function that is derived from abundant experiment data of stress level and failure time(Schmidtke & Lajtai, 1985), and similar result by relationship between stress state and failure time was also suggested (Lau & Chandler, 2004; Aubertin et al., 2000; Sangha & Dhir, 1972). According to relationship between steady creep rate and stress state during creep, a critical stress that transforms steady-state creep to accelerated creep was studied and the long-term strength was suggested (Tsai et al., 2008; Ma & Daemen, 2006; Lajtai et al., 1991). Based on the results of experiment in compression, the long-term strength of rock was defined by stress at volume strain reversal. When applied stresses are larger than the long-term strength, the microcracks in the rock will grow constantly, damage of rock will increase and failure of rock will occur finally (Chandler, 2013; Bieniawski, 1967; Brace et al., 1966)."

Jan 1, 2015

By A. Mehinrad, F. Rafia

"The Dez River flows from the Zagros Mountains into the great Khuzestan plain, Southwest of Iran. The 203 m high Dez Dam is a double curvature thin concrete arch dam, with a Pulvino, founded on thick bedded to massive conglomerate of Bakhtiary Formation, mainly horizontal and very less jointed at the dam site. Construction work was completed in 1963, creating a reservoir with a total storage volume of 3’315 million m3. The dam body, with some 350’000 m3 volume and (W/H=1.1/1.0), is the dominant feature of the project.Geological and geotechnical studies at the dam site started in 1957 and continued during the whole period of dam construction. Simultaneously, two extensive programs of laboratory testing were carried out in New York and Milan.Most of the results were recorded in the project design documents and in two very well-known papers of Talobre et. al. (1964) and Dodds (1966), however, no detail results are available for most of tests.In order to estimate geomechanical parameters of the rock mass foundation for numerical modeling of the dam body and its foundation, reassessment of the in-situ and laboratory test results using the recent rock mechanics methods was required.This paper explains how the outcomes of those tests, performed more than 50 years ago, were reevaluated and how the definitions and parameters presented in the project reports were re-interpreted using the recent rock mechanics concepts and definitions. Also, the results of classification of Bakhtiary conglomerate using GSI system and application of Hoek & Brown failure criterion for estimating rock mass parameters have been described.INTRODUCTIONThe Dez River flows from its headwaters in the Zagros Mountains into the great Khuzestan plain. Just before entering the plane, the river passes through a narrow, steep gorge that is about 17 km long. The Dez Dam is located at the entrance to this gorge, some25-km upstream of the city of Dezful and 150-km upstream from the provincial capital Ahwaz (Figure 1)."

Jan 1, 2015

By Y. Wang, S. Liu, K. Jiang

China is the world’s largest producer and consumer of non-ferrous metals. In recent years, significant progress has been made in research and commercial application of pressure leaching technology to produce some nonferrous metals. Research and development activities include a low-pressure, low-temperature leaching technology for complex copper concentrates, a hematite process to treat pressure leach solutions from zinc concentrates, and a pressure leaching - solvent extraction process for molybdenum and rhenium. Examples of commercial practices include a two-stage pressure leach technology in a zinc plant in Danxia, a direct leaching technology in a zinc plant in Zhuzhou, a high pressure acid leaching process for a nickel laterite project in RAMU, and a pressure leaching technology to treat arsenic sulfides in a plant in Guixi. The development of pressure leaching technology for the recovery of lead, vanadium, gallium, germanium, and precious metals in China will also be described in this paper.

Jan 1, 2015

By K. Chattopadhyay

Fluid flows in metallurgical reactors play a vital role on liquid metal cleanliness for both ferrous and non-ferrous metallurgy. Thus, it is absolutely critical to understand different fluid flow mechanisms, and the use of computational methods to model the complex non-isothermal, turbulent, single- and multiphase-flows, has to be appreciated. The present case study emphasizes on controlling the flow of liquid steel in a tundish and enhancing liquid metal cleanliness. CFD modeling was used to build a robust mathematical model, and effects of flow control furniture and non-isothermal conditions were analyzed. The mathematical model was validated against water model experiments. Parameters that were conducive for inclusion removal were identified and implemented in the plant. Some flow control devices could increase inclusion removal to a great extent compared to the existing configurations. In cases, where a hot ladle was poured into a relatively cooler tundish, inclusion removal was better, whereas results were catastrophic in cases where colder liquid was poured from ladle to the tundish. Similar techniques can be applied for other liquid metals including light metals and non-ferrous metals.

Jan 1, 2015

By Patrick K. Wong, Richard Kelly

"The variability in strength and compressibility of in situ deep soil mixing products can be greater than the variability of the natural soil. However, satisfactory performance can be achieved by careful construction and an appropriate QA/QC program. This paper presents a case study on the use of deep dry soil mixing columns to support several embankments over soft clay along a highway project. Post-construction settlement monitoring indicated that good performance is achieved where the acceptance criteria are met, except in an area with high organic content. Embankments with contrasting performance are compared to the quality control test results which comprised laboratory testing of core samples as well as in situ test results such as pull-out and push-in vanes and conventional cone penetration tests. Drawing on the performance results and quality control testing, discussions and guidelines are given on quality assurance acceptance criteria and construction control testing regime for future projects.INTRODUCTIONBetween 2008 and 2012, the largest deep dry soil mixing (DSM) contract during that time in the southern hemisphere was carried out for the Ballina Bypass project. The project, comprising 12 km upgrade of the Pacific Highway located in northern New South Wales close to the border of Queensland, was commissioned by the Roads and Maritime Services (RMS) of NSW. The ground improvement contractor was Keller Ground Engineering (KGE) Australia. Seven different types of ground improvement techniques were employed for the project, ranging from low embankment strategy with nominal preloading, to surcharge with wick drains, light weight bottom ash fill, DSM, vibro-replacement stone columns, dynamic replacement, and vacuum consolidation (installed by Menard Bachy Pty Ltd). Different techniques were chosen depending on time program, cost, and performance requirements relative to proximity to piled structures (e.g. bridge abutments) and post-construction settlement and differential settlement for either rigid or flexible pavements at different locations.DSM was the most utilized ground improvement technique employed on the project, comprising a total of about 285 km of 0.8 m diameter columns to depths up to 18 m for the purpose of supporting bridge approach embankments and culverts with embankment heights up to 6 m. DSM was chosen due to the very soft nature of the clay soil with moisture content practically at liquid limit, and the relative speed and economy of the system. Dry cement powder at rates of 160 kg/m3 to 200 kg/m3 were pneumatically discharged via the hollow stem of the mixing tool, and mixed with the soil (using multiple horizontally mounted paddles on a single vertical stem) at high speed as the mixing tool is withdrawn."

Jan 1, 2015