Search Documents

By Y. Wang, L. Liu, G. Xu, Y. Lv J. Sheng H. Zhang

In order to increase the service life of large scale coke dry quenching furnaces, the damage mechanism of lining was investigated, and the structure and properties of lining refractories used in cooling section were researched. The results showed that the abrasive wear volume of lining bricks at one fourth height section under skew tunnel was smaller than other sections. The wear loss of mullite brick and dense clay brick used in the lining of cooling section were respectively 8.02 cm3 and 11.65 cm3 in fifteen minutes. The mullite brick was laid with clay brick alternatively. By the different wear rate, the surface of lining was rough and uneven in the later service life, and short brick was easily dropped from lining. During the service, the basis wore off more easily than the aggregate. It is necessary to improve the wear resistance property, which will increase the service life of cooling section’s lining for coke dry quenching furnaces.

Jan 1, 2016

By Mehmet Bu daycı, Onuralp Yücel, Ahmet Turan, Murat Alkan

In this study, iron based alloys (Fe, Fe-Cr-Ni-Mo, etc.) were produced by using metallothermic methods starting from Mill Scales obtained continuous casting processes. During the process, the combustion was realized by ignition and the produced wave propagates throughout the reactant mixture yielding the desired product. In this work, Mill scale used as an iron source, which includes +2, +3 values iron oxides. Aluminum, Magnesium and Silicon were used as reductants. In these metallothermic experiments, different ratios of reductants were examined, and their effects on the metal recovery and alloy compositions were investigated. The samples were characterized by using chemical analysis (AAS), XRD and XRF techniques.

Jan 1, 2016

By Mei-le He, Min Chen, Xiang Shen, Lei Xu, Lei Liu, Nan Wang, Xue-liang Yin

In the current study, Al2O3-MgO-CaO refractories were prepared at 1400-1600 by the addition of MnO micro-powders, and the effect of MnO addition on densification behavior of the refractory was discussed. The results showed that the doped MnO dissolved to MgAl2O4 phase, and promoted the growth of MgAl2O4 grains by the formation of MgAl2O4 solid solution. As a result, the dense microstructure was obtained, with the apparent porosity decreased from 19.2% to 5.4% and the bulk density increased from 2.78g/cm3 to 3.15g/cm3 after firing at 1600 for 2h by the addition of 4% MnO. In addition, a texture microstructure was observed, which is considered to be favorable to improve mechanical properties and the service life of Al2O3-MgO-CaO system refractories.

Jan 1, 2016

By Caryn Wendt, Donna Post Guillen, Armando McDonald, Erik R. Coats, Chaston Ellis, Kevin Feris

Dairy operations constitute ~2.5% of annual U.S. greenhouse gas (GHG) emissions, making dairies one of the largest sources of industrial GHG emissions. We are developing a novel, integrated system to achieve a net reduction in dairy GHGs while producing value-added materials and products. This integrated manure-to-commodities system converts dairy manure to bioenergy, sequesters carbon by converting volatile fatty acid-rich fermenter supernatant to bioplastics, and utilizes anaerobic digester (AD) and polyhydroxyalkanoate (PHA) reactor effluents to produce algae that can be harvested and internally recycled to enhance PHA production and sequester carbon. A decision-making tool is being developed for the integrated system that quantifies net GHG reduction, carbon sequestration, nutrient management and economics.

Jan 1, 2016

By Qian Xu, Guangshi Li, Xionggang Lu, Xingli Zou, Hongwei Cheng, Cong Xu, Changyuan Lu

The roasting of nickel-bearing sulfides is a complex but important process which has not been adequately characterized. Combination of X-ray diffraction and scanning electron microscopy has been proved to be useful for such experiments. The leaching results of nickel, copper, iron and cobalt was analyzed by ICP methods. Process possibility of polymetallic sulfide concentrates through a three-step procedure (oxidation roasting - chlorination - water leaching) was suggested. Ammonium chloride could react with nickel/copper oxides to produce intermediate complexes. At the temperature range of 280~340 oC, these complexes further decomposed to the corresponding simple chlorides. Roasting sulfide concentrate using NH4Cl is effective for complex ores.

Jan 1, 2016

By M. Wenzel, Dang Thanh Tung, Nguyen Anh Duc, Nguyen Huu Luong, Dang Van Sy, N. Kelly, K. Gloe, K. Kretschmer, Phuc Nguyen Le, K. Schnaars, S. Robles M, L. Götzke, J. J. Weigand

The recovery of rare earth metals from secondary sources has attracted much attention due to their ever expanding demand in the high-tech industry. The studies reported here focus on the hydrometallurgical recovery of lanthanum and cerium from spent fluid catalytic cracking (FCC) catalysts in a two-step process: leaching with nitric acid and solvent extraction by tri-n-butyl phosphate (TBP) and di(2-ethylhexyl)phosphoric acid (D2EHPA). The experiments show a high dissolution yield of about 93% lanthanum and 42% cerium in a single leaching step with 2 M (126 g/L) HNO3 at 80 °C; only 11% aluminum has been dissolved simultaneously. In the subsequent solvent extraction step the best results for this leach liquor could be achieved using a 1:1 mixture of 25% (v/v) TBP (0.92 M) and 25% (v/v) D2EHPA (0.76 M) in n-decane without the need for any pH adjustment. In that case La(III) and Ce(III) can be extracted with 60% and 74% yield respectively in one stage from the majority of accompanying matrix elements. In particular no extraction of Al(III) could be observed under these conditions.

Jan 1, 2016

By Shengfan Zhou, XUEWEN WANG, Bianfang Chen, Mingyu Wang

Vanadium was leached from roasted stone coal by NaOH solution, and the effect of leaching temperature, leaching time, addition of NaOH, liquid to solid ratio, the grinding fineness of stone coal, and stirring speed on the vanadium leaching rate was studied. The kinetics analysis for the process is presented by the shrinking core model. The results show that the vanadium leaching ratio of roasted stone coal can be beyond 75% at the 6% NaOH addition, leaching temperature of 95°C, leaching time of 7h, liquid to solid ratio of 1.2mL/g, and grinding fineness of 0.111mm. The leaching process is controlled by interfacial reaction kinetics and the apparent activation energy was 59.36kJ/mol.

Jan 1, 2016

By Zhengjie Chen, Wenhui Ma, Jijun Wu, Kuixian Wei

The gasification reactivity of PC (petroleum coke), strengthened by addition of different potassium carbonate proportions using different grinding medium, was investigated by using thermogravimetric analysis (TGA). Results showed that the gasification reactivity of PC not only increased with the increase of catalyst-loaded, but also showed the effective improvement by anhydrous alcohol. The PC was mixed with potassium carbonate [K2CO3] catalyst at 0.5%, 0.8%, 1.0% and 1.5%, and then ground wet with distilled water. The CO2-gasification rate of PC was only 77.35%, 80.55%, 84.07% and 85.88% under the gasification temperature 1100 °C and holding time 120 min, at different K2CO3 respectively. However, when the PC was ground in anhydrous alcohol at the same condition of catalyst-loading, the gasification rate of PC reached 95.43%, 96.63%, 95.50% and 95.61% at the holding time of 108 min, 101 min, 74 min and 35 min, respectively. It was shown by FTIR, SEM and EDX determinations that the anhydrous alcohol used as the grinding medium can further improve the gasification reactivity of PC when compared with the distilled water.

Jan 1, 2016

By Qiang Zhong, Bin Xu, Qian Li, Wei Gao, Yongbin Yang, Yaxuan Wang

Lump coal with high volatility is used for providing heat and reductive gas, and ensuring permeability in COREX. However, it is apt to be pulverized in transport and storage process. Therefore, comprehensive utilization of the pulverized coal to produce coal briquettes with appropriate binders is significant, among which the molasses binder cannot meet the technological requirements. In this paper, coal tar pitch binder and BJ additive were used in briquetting and carbonizing process of coal powder. The results showed that BJ effectively activated cold state cohesiveness of the pitch and make it bond the coke particles to a firm briquette at room temperature .Carbonizations of coal and coal tar pitch achieved obvious constriction and formed a carbonized skeleton. The drop resistance of wet briquettes reached over 50 times/1meter. When cured at 1000 °C for 1h under nitrogen atmosphere, the compressive strength of carbonized briquettes came to 6.43 Mpa.

Jan 1, 2016

By ZhiLong ZHAO, Lin Lin, Zhancheng Guo, Jingtao GAO, Huiqing Tang

Grain sticking often occurs in the fluidized bed reduction of f ine iron ore, which is closely related to the precipitation morphology of metallic iron on the surface of ore particles. In this work, simulating the gas-solid reduction process of iron ore, in situ observations were carried out to investigate effects of doping mineral oxides on the precipitation morphology evolution of metallic iron during reduction of iron oxides with CO. Results indicate that the precipitation morphology of metallic iron is related to the quantity of doped mineral oxides. The minimum mole fraction of doped oxide ( xyOA N ) that can inhibit the growth of iron whiskers is related to its cation radius ( Ax r ), extranuclear electronic layers ( Ax n ) and valence electrons ( Ax q ). Their relation can be expressed as:

Jan 1, 2016

By Yuanbo Zhang, Zhixiong You, Li Qin, Guanghui Li, Tao Jiang

Low-grade manganese oxide ore is generally characterized by high iron content. In this work, sulfidation roasting of an iron-rich manganese oxide ore with elemental sulfur was characterized. The experimental results indicated that manganese dioxide can be selectively reduced over iron oxide by using elemental sulfur. The manganese phases in roasted product included low-valence manganese oxide, manganese sulfide and manganese sulfate, while those of iron mainly depended on the sulfur addition. Iron oxide would only be reduced or sulfidized at larger sulfur additions. The effect of roasting temperature and S/Mn mole ratio on the phase transformations was also investigated; extractions of Mn/Fe by sulfuric acid were evaluated. An extraction of Mn greater than 95% was obtained while that of Fe was controlled less than 10% under the optimal conditions.

Jan 1, 2016

By Linfeng Zhou, Yuanbo Zhang, Rong Sun, Guanghui Li, Zhiwei Peng

The volatilization behavior of rhenium in the process of oxidative roasting of a molybdenite concentrate with 43.55 wt.% Mo and 321 g/t Re is explored based on identifying the relationship between volatilization of sulfur and rhenium. The results show that rhenium volatizes after sulfur and precise control of operating variables plays an important role in separating rhenium from molybdenite concentrate. When the roasting parameters are optimized as follows: roasting temperature 600 oC, roasting time 2 h, roasting atmosphere air, the volatilization rate of rhenium reaches 89.26%. In the process of solidification roasting, the volatilization rate of rhenium decreased almost to zero when the ratio of slaked lime/molybdenum concentrate was 10% excess to the stoichiometric requirement at 600 oC for 2 h.

Jan 1, 2016

By Xiaoyan Xiang, Wenqiang Yang, Wentang Xia

Magnesium aluminate spinel is widely used in the metallurgical industry as refractory material, however, natural magnesium aluminate spinel is rare and most of the magnesium aluminate spinel is synthetic. The traditional synthesis of magnesium aluminate spinel often needs high temperature, which leads to more energyconsumption. In this article, solid phase sintering process was employed to synthesize magnesium aluminate spinel, in which, magnesium and aluminum oxide were used as raw materials and magnesium and aluminum powder were used as composite additives. The mass ratio of magnesium and aluminum on the effect of synthesis of magnesium aluminate spinel and the characteristic of the synthesis at different temperature and time was discussed. Experiment found that the synthesis temperature was observably lowered when the addition of magnesium and aluminum was 2.0% and 1.0% respectively.

Jan 1, 2016

By Yuanbo Zhang, Bingbing Liu, Zhuyin Chen, Xiao Kang, Chen Liu

Composite agglomeration process (CAP) is an effective method to utilize the iron-bearing dusts generated in the ironmaking plants, by which the dust percentage in the sinter feed can be increased up to 20 wt %. In the current study, a comparison on behavior of iron-bearing dust in the conventional sintering process (CSP) and CAP was characterized. The results showed, in the CSP products, the scattered iron-bearing dust in the mixture was disadvantageous for the sintering indexes and consolidation of the finished sinters. In the CAP products, the main phase in the iron-bearing dust pellets was well-crystallized Fe2O3 grain particles. In the matrix parts, there were more Fe3O4 particles generated, which caused to high RDI+3.15 and low RI of the finished products. The pellets and the matrix parts were bonded by iron oxides and acicular calcium ferrite.

Jan 1, 2016

By Cong Wang, Siyang Long, Pengcheng Zhang, Haibin Zuo

This paper introduced the research progress of microwave treatment on coal. The mechanics of microwave treatment mainly include thermal effects and non-thermal effects. Thermal effects, which lead to cracks and changes of pore structure, attribute to the selective heating of microwave. Non-thermal effects involve the removal of oxygen functional groups, improvement of coal rank and decomposition of minerals. Therefore, microwave treatment of coal has a lot of potential applications, mainly including drying, desulfurization, improvement of grindability, enhancement of coal-water slurry property and change the combustion and gasification properties.

Jan 1, 2016

By Qian Xu, Xionggang Lu, Xingli Zou, Zhongfu Zhou, Shuhua Geng, Hongwei Cheng

Herein we report an electrochemical route from oxides (SiO2, TiO2)/sulfide (MoS2)/carbon mixture precursors to Mo-Si-Ti-C composites in molten salt. The electrochemical process was carried out in molten CaCl2 at 800 °C with a potential of 3.1 V, and a graphite-based anode was used in the electroreduction process. The reaction mechanism and the influences of the stoichiometry of the initial mixture precursor on the morphology and phase composition of the final products were investigated. It has been found that Mo5Si3/MoSi2/Mo3Si/Mo, Mo5Si3/MoSi2/Mo2C/SiC, and Mo5Si3/Mo2C/Ti3SiC2/TiC/Mo composites can be electrosynthesized directly from their oxides/sulfide/carbon mixture. The preliminary experimental results suggest that the electroreduction process can be used for the controllable electrolytic production of alloys/carbide-containing composites from oxides/sulfides/carbon precursors.

Jan 1, 2016

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By Drew M. Kurtz, Jeff L. Rai, Sara F. Frailey, Mohammad Ayub Iqbal

"This paper presents the foundation changes made for a five-span bridge over the Lehigh River constructed as a design-build project. During excavation within the cofferdam at Pier 2 for the construction of a spread footing to bear on rock, it proved extremely difficult to control the water entering the excavation as the sheet pile tips were variable due to the bedrock pinnacles and a weathered rock zone above the top of rock allowing water to pass below the sheeting. Water also entered from the bottom of the excavation, possibly due to the presence of solution openings within the dolomite bedrock. After repeated failures to achieve subgrade elevation and maintain a dry excavation, a design change to drilled shafts was made. Additional borings were performed for each of the shaft locations to explore the area underlain by karstic dolomite rock. A seal consisting of tremie concrete with adequate weight was placed to counter the differential head of water and the three drilled shafts (with minimum 25 feet [7.62 meter] rock sockets) were installed. A detailed construction sequence was followed and advanced quality control testing was performed. The construction of Pier 2 was completed successfully.1. INTRODUCTIONThis paper presents the description of the design change made from spread footing to drilled shafts as a result of site conditions encountered during the excavation for the spread footing for a bridge pier in the Lehigh River in Allentown, Pennsylvania. The bridge is located in an area underlain with dolomite rock, presenting karstic conditions including irregular top of rock and solution openings that provided high hydraulic conductivity below the top of rock. Also, the presence of a zone of weathered rock and pinnacle rock prevented the advancement of sheet piles when constructing the cofferdam. Thus, the difficulties of advancing the excavation to the desired spread footing level resulted in the design change to drilled shafts during construction. Since the project was Design-Build, the design could be changed by a collaborative process through the efforts of the Contractor, its geotechnical and structural engineers, and the State's (owner's) geotechnical and structural engineers and construction management staff."

Jan 1, 2016

By Verya Nasri, Mehdi Bakhshi

"Fiber reinforcement has emerged as an alternative to steel bars in precast concrete segments due to advantages such as saving cost and reducing production time while developing a more robust product with improved handling and long-term durability. ACI recently drafted a new report as the first design guideline on FRC tunnel segments to provide specific guidance for this emerging technology. ACI document offers general information on the history of FRC precast segments from tunneling projects throughout the world; a procedure for structural analysis and design based on governing load cases, and a description of the material parameters, tests and analyses required to complete the design. This paper summarizes the design considerations in this ACI guideline prepared by the authors of this paper as the main contributors. Application of this guideline to design of a tunnel with an internal diameter of 5.5 m (18 ft) results in elimination of steel bars.INTRODUCTIONPrecast concrete segments are installed to support the tunnel excavation behind the Tunnel Boring Machine (TBM) in soft ground and weak rock applications. The TBM advances by thrusting off the completed rings of precast concrete segments that provide both the initial and final ground support as part of a one-pass lining system. These segments are typically designed to resist the permanent loads from the ground and groundwater as well as the temporary loads from production, transportation and construction. Tunnel segments are generally reinforced to resist the tensile stresses at both the Serviceability (SLS) and the Ultimate Limit States (ULS). With traditional rebar, a significant amount of labor is needed to assemble the cages and place the rebar, which results in higher production costs.Fiber Reinforced Concrete (FRC) can be used to enhance the production, handling, and placement of precast concrete segments. This is because of the uniform dispersion of fibers throughout the segment to include the concrete cover, which is very advantageous for resisting the bursting and spalling stresses. These stresses develop as a result of the high loads induced on the segments during the TBM jacking process. The presence of fiber in the concrete matrix helps mitigate against unintentional impact loads during segment handling and tunnel construction operations."

Jan 1, 2016

By Georgios Kafantaris, Carsten Bonde, Nataša Katic

Within the investigation works for the Copenhagen Cityring metro, Geo/CMT have carried out 90 geotechnical boreholes. Together with the previously available investigation, this resulted in more than 15 km of vertical drillings and several thousands of laboratory tests. The design is made for 17 stations, four shafts and two parallel 16 km long tunnels. The geotechnical investigation and design have been carried out in several stages comprising appropriate refinement of structural design and design of excavation operations, including TBM break-in and launching operations at each station shaft. Acceptance of the solution and / or refinement of the investigation and design schedule in the next stage were based on the geological conditions, area availability at surface level, planning and cost-control criteria. The applied recursive design refinement is presented herein with an example of the Østersøgade shaft location.

Jan 1, 2016