Search Documents

By Eric Keller, Jamal Rostami, Wenpeng Liu

"Roof and rib instability is an important issue in underground mining. To optimize ground support design, enhance ground stability, and reduce the possibility of roof or rib failure with minimal use of artificial ground support, it is essential to have an accurate understanding of ground conditions. This includes the location of voids, cracks, and discontinuities, as well as information about the different strata in the immediate roof. This paper briefly introduces ongoing research on void detection by using the roof bolter feed and rotation pressure. The goal of this project is to improve the sensitivity of detection programs to locate smaller joints and reduce the number of false alarms. This paper has presented a brief review of the testing procedures, data analysis, logic, and algorithms used for void detection. In addition, this paper has discussed the results of preliminary laboratory tests and statistical analysis of the data from these two drilling parameters used for void detection.INTRODUCTIONRoof falls are one of the most serious and frequent accidents in underground mining. Each year, personnel are injured or killed because of roof falls. Equipment can also be damaged when this occurs. According to Mine Safety and Health Administration statistics collected from 1999 to 2008, ground falls were the largest cause of fatal accidents in underground coal mining, causing around 40% of all fatalities (NIOSH, 2015a). Out of 8 to 10 fatalities and over 800 injuries are recorded each year in underground mines, there are nearly 2,000 reportable non-injury ground falls every year (NIOSH, 2015b).Certain features in the ground, such as voids, cracks, and discontinuities, are significant factors that cause roof support failures and roof fall accidents. Currently, several manufacturers provide smart roof bolters with limited capabilities for void detection. While successful in many instances, in laboratory experiments, the existing void detection systems have limited success in detecting void openings that are less than 1/8 inch This limited success was observed in testing concrete blocks with gaps in between, simulating a rock medium with voids. Detection programs have missed some voids, while, in some cases, they have shown false detection. These algorithms need to be more accurate in sensing voids to improve the capabilities of these programs."

Jan 1, 2016

By H. Wotruba, J. Heizmann

"The use of shotcrete is a mandatory means for rock support and therefore for safety in many underground mining operations. If shotcrete gets into the flotation feed though, it can negatively influence the flotation process. This especially occurs when sublevel stoping, cut-and-fill or room-and-pillar methods are applied because as the mining face moves on, formerly applied shotcrete layers are mined together with the ore.As shotcrete does not differ significantly from fluorspar ore in its physical properties it gets moved through the comminution process and is fed to the flotation plant like the ore. To prove the influence of shotcrete on the flotation process, a laboratory test series was conducted at the Unit of Mineral Processing (AMR) of the RWTH Aachen University. The shotcrete grade of the flotation feed was varied between 0 and 10% through addition of pure shotcrete. Flotation parameters and also reagent dosage were held constant apart from the addition of the pH regulator, which was dosed to reach a constant pH of 8 at the flotation start. Results showed that with increasing shotcrete grades in the flotation feed the fluorspar recovery as well as general mass recovery decreased. The enrichment factor of Fluorspar also decreased with increasing shotcrete grades in the feed.In an effort to eliminate the shotcrete contamination of the flotation feed, a feasibility study for use of sensor-based sorting prior to the comminution process was conducted. Rock sorting not only reduces the bad influence of shotcrete on the flotation process, but also reduces comminution costs. INTRODUCTIONShotcrete is used in underground mining on a regular basis. It is used for rock support and therefore to increase safety in the underground mining environment. In mineral processing the presence of shotcrete can cause difficulties for example in the concentration processes. In flotation the highly sensitive reagent mixtures can be disturbed by the chemical activity of shotcrete and therefore recovery rates and selectivity of the process can suffer.Shotcrete is a special form of concrete which is applied pneumatically with high velocities and is compressed by its impact energy. Since the process is especially suitable for work in difficult environments and overhead areas, it is established in underground mining for many years. Shotcrete is not only applied in pre-processing of the mines, but particularly of use for cut and fill, as well as room and pillar mining methods. There it is used to secure excavation chambers. When the mine face is secured with shotcrete and subsequently the mining continues, the applied shotcrete will automatically be mixed with the ore."

Jan 1, 2016

By J. D. T. Steyl, C. A. Biley

"The chemistry of electrolyte systems containing iron remains generally poorly understood despite their prevalence in many natural and industrial processes, particularly in hydrometallurgy. These systems are typically challenging to study and model due to their affinity for complex formation and precipitation even at low pH. Recent developments in the hydrometallurgical processing of nickel laterites at Anglo American have called for a deeper understanding of the fundamental chemistry of the Fe2(SO4)3–FeSO4–H2SO4–H2O system. This paper details the development of an internally consistent, Pitzer ion-interaction model of this system, with explicit recognition of important contact ion pairs (CIPs). The primary application of this model is a thermodynamic framework for the interpretation of kinetic processes occurring during iron(III) reduction with SO2. Adopting a rigorous thermodynamic basis for the system chemistry facilitates the formulation of simple rate expressions that are capable of inherently capturing complex effects. While the iron(III) reduction case study remains the focus of this work, the developments have more universal applications and the thermodynamic speciation model can be extended into other systems containing acidic ferric sulfate.INTRODUCTIONIron is present in nearly all hydrometallurgical refining circuits typically as both a necessary and unwanted impurity and needs to be removed and disposed in a safe and efficient manner. This is generally performed by precipitation to form a range of solids such as hematite, goethite or jarosite. Numerous studies in the open literature have focussed on the removal of iron from refractory gold sulfide ore (Berezowsky & Weir, 1989; Berezowsky et al., 1991) and zinc pressure leaching (Buban, 1999; Ismael, 2003), and PGM matte sulfide circuits (Dutrizac & Monhemius, 1986). Moreover, since ferric iron is a strong oxidizing agent, it has been used extensively as a leaching agent for sulfide minerals (Dreisinger, 2006). Given the outlook of challenging economic conditions, declining ore grades and increasing levels of impurities, effective iron management is going to become increasingly critical to all hydrometallurgical processes.Against this background, and considering the widespread importance of acidic iron sulfate systems throughout natural and industrial processes, it is unexpected that the knowledge of the fundamental solution chemistry of these systems contains such significant gaps, particularly at the conditions typically found in hydrometallurgical applications. Existing literature describing the measurement and modelling of solution speciation in these systems have highlighted their significant chemical complexity (Magini & Caminiti, 1977; Magini, 1979; Lee & Tavlarides, 1985; Stipp, 1990; Papangelakis et al., 1994; Gil et al., 1995; Majzlan & Myneni, 2005; Kormanyos et al., 2008; Yue et al., 2014). Partially responsible for the lack of quantitative speciation measurements is the strong tendency of ferric to hydrolyse at even low pH (Flynn, 1984), complicating the laboratory study of such systems. Moreover, the large number of aqueous species that may co-exist simultaneously makes the study of individual species and the modelling of the numerous interactions between these species extremely difficult (Dry & Bryson, 1988; Stipp, 1990; Majzlan & Myeni, 2005; Kobylin et al., 2007)."

Jan 1, 2016

By Jochen Petersen, Alison Lewis, Cledwyn Mangunda

Run-off and waste water streams high in dissolved metal content are generated in all mining operations. The metals pose a threat to life due to their persistent bio-accumulative toxic (PBT) characteristics. Hence, there is a need to treat mine waste water effectively. Lime precipitation is the technology of choice through which Fe, as the major metal species, is removed as Fe (III) oxyhydroxides with other metals co-precipitated and/or adsorbed. Sulphates are removed as gypsum or incorporated into the Fe phases. The resulting sludge has poor dewatering characteristics and is deposited in landfills, with an inherent risk of returning the Fe back into the water cycle through leaching. This study seeks to understand the mechanisms behind the formation of this sludge in terms of product quality. The relationship between process conditions and product characteristics has been investigated through exploring the effect of Fe (III) concentration on the precipitate product characteristics (particle size distribution (PSD), size, morphology and structure) and quality (in terms of filterability, settling ability, etc.) in a simplified system. Neutralisation of acidic synthetic aqueous Fe (III) sulphate streams containing 50, 400 and 800 mg/L Fe(III), respectively, was effected by mixing it in a continuous stirred tank reactor (CSTR) with dissolved calcium hydroxide for pH control at a residence time of 15 minutes. Precipitate samples analysed for morphology and PSD, using nanoSEM and Zetasizer respectively, showed a general decrease in PSD and zeta potential with increases in feed Fe (III) concentration. These results were used to infer the particle size enlargement mechanisms of Fe (III) oxyhydroxide precipitates under a given set of operating conditions. Preliminary product quality results indicate that a high concentration (800 mg/L) leads to the rapid formation of metastable precursors with poor product quality, whilst a low concentration (50 mg/L) leads to formation of thermodynamically more stable precipitates with good product quality. The approach demonstrates a potential route forward in terms of linking operating conditions to the attainment of desirable characteristics rather than specific precipitate phases which are difficult to identify.

Jan 1, 2016

By A. J. Smethurst, S. B. Hearn, S. Boskovic

"The problem of crud in solvent extraction is well known and can be a major handicap and operational issue. Colloidal silica can cause a number of problems including interfering with flocculation, initiating crud formation in solvent extraction (SX), decreasing SX extraction kinetics and increasing SX phase disengagement times. Flocculation can be utilized to remove some of the troublesome particulates but colloidal silica does not flocculate well and presents a different problem requiring innovative chemistry to solve. Coagulants can assist by facilitating the removal of this colloidal silica by promoting the agglomeration of the particles to a size which can be more readily settled or flocculated in solid/liquid separations. This is achieved when the coagulants bind to the surfaces, displacing water and destabilizing the colloids, whereupon they bind to each other which facilitate their amenability to conventional flocculation.INTRODUCTIONSilicate minerals are abundant in the upper layers of the Earth’s crust, and there are few mineral deposits without significant levels of gangue silicates. Silicate minerals include the pure silicas, such as quartz and other silicate containing minerals such as clays, chlorites, feldspars, as well a vast number of less common silicates.During the acid leaching of ores, two types of fine silica particles are released in solution from the dissolution of the host mineral. The first consists of partly depleted silicates, and the second is colloidal silica, which forms in solution. It is this second type which has the potential to cause crud formation as well as poor solution clarities, slow filter rates and excessive flocculant usage (Figure1)."

Jan 1, 2016

By X. L. Song, G. W. Zhang, F. Y. He, X. Xiao, L. L. Huang

This paper presents the design of a model and process simulation of a vertical mill based on a population balance model. The simulator, Simulink, which is a systematic modeling tool within MATLAB, was used for the simulation. The model will simulate the real time variation trend of each size fraction in the feed material to the vertical mill, as well as, the size distribution of the batch grinding products. Breakage distribution and selection functions are calculated based on batch grinding laboratory experiments using Back-calculation method. The simulated size distributions correspond with those in the actual mill operation having a relative error of less than 0.50%. This work lays the foundation for future research on modelling and simulation of a closed circuit grinding operation consisting of a vertical mill with hydrocyclone classifier.

Jan 1, 2016

By D. Runnels, Daniel Roy, Ricardo Esteban, J. Torrealba-Vargas

"An intuitive way to reduce power consumption in grinding operations is to feed the grinding circuit with finer feed by enhancing blasting and fragmentation control. The optimization of blasting with the objective of minimizing power consumption in grinding is not new.The study was based on a Canadian mine that processes a very hard ore. BBA conducted blasting/fragmentation and grinding circuit surveys in 2014. The results of the exercise were used to develop a base case model to simulate the effect of blasting in the operation on the grinding circuit. Tools for fragmentation simulations, particle size measurement and crushing/grinding simulations were used with the objective of reducing the OPEX costs including power consumption.The paper describes the steps involved in the model optimization as well as an economical evaluation of the OPEX savings.INTRODUCTIONIn 2014 BBA was retained by one of its clients to conduct a crushing and grinding survey. The objective of the survey was to update the grinding circuit model with production data and also to develop a tool to investigate opportunities for process improvement.A second phase of the study involved the development of drilling and blasting and crushing models. The models were used to diagnose the operations and to investigate opportunities for process improvement.The objective of the present study is to describe the approach and to identify potential improvements to overall mine site operating costs by better integrating mining and milling operating costs with blasting and grinding models."

Jan 1, 2016

By M. O. Makwarela, M. W. Erwee, K. Bisaka

"Energy efficiency in mining and minerals processing forms part of Mintek’s long-term research strategy which includes a specific programme designed at overcoming the challenges faced by the South African pyrometallurgy industry.The electric smelting industry is currently severely constrained by the global economic downturn as well as by the availability and increasing cost of electricity. Efficient utilisation of electricity through energy recovery systems and improved smelting process flowsheets can significantly contribute towards creating sustainable operations.Apart from efficient engineering design and solid process control, smelting of either cold or hot pre-reduced ores has been shown to decrease furnace electricity consumption by more than 40%. Various methods of solid-state reduction tests have been carried out at Mintek in order to select the most appropriate process option in the context of the South African industry. This paper summarises a subset of the results obtained, specifically on pre-reduction tests done on South African chromite and manganese ore pellets.In this set of tests, it was found that the use of an organic binder, together with B2O3 as flux, promotes manganese ore pre-reduction, but retards the pre-reduction of chromite. By pre-reducing the manganese ore feed, significant cost savings can be achieved in subsequent smelting processes and there is potential to minimise manganese losses as a result of fuming, due to possible lower operating temperatures."

Jan 1, 2016

By J. Oyunaa, P. Munkhbaatar, A. Sarnai

"The molybdenum mining process used at Mongolia Erdenet Company is a selective flotation of molybdenite from the copper porphyry ores in which the extraction of molybdenum comes as a byproduct of the ongoing copper production.The mineralogical composition of molybdenum concentrate is 99.4% molybdenite (MoS2), 0.09% molybdenum oxide (MoO3), 0.52% powellite (CaMoO4) and wulfenite (PbMoO4) and content 47.76– 47.92% molybdenum, 1.5–2.67% copper, 0.04% renium.From compared solvents sodium and carbonate and ammonia are like extracted molybdenum than hydrochloric acid, which contained 96.23–97.72 p.c. of its total amount. Hence to take into consideration abundance, cheap and suitable for analysis and processing the molybdenum concentrate ammonia is choosing as a basic solvent. By direct evaporation of ammonia extract solution, we obtained ammonium ortomolybdate, which contains 73.47% MoO3. INTRODUCTIONMolybdenum occurs in the earth’s crust in an abundance of about 10–14%, mainly as molybdenite, MoS2. Small quantities are also associated with other metals having similar chemical properties. Thus wulfenite (PbMoO4) is found in oxidized parts of sulfidic lead deposits in many regions of the world; powellite [Ca(Mo,W)O4] is a calcium molybdate usually formed from the modification of molybdenite in deposits containing tungsten as scheelite (CaWO4) and tungsten substitutes for molybdenum up to about 10%. Ferrimolybdite (Fe2Mo3O12·8H2O) is the product of oxidation of molybdenite in the presence of iron (III) compounds. Molybdenite is the primary source of molybdenum. Should demand for molybdenum rise so that additional sources become necessary, wulfenite, powellite, and ferrimolybdite may become commercially significant. Molybdenum ore is mined by underground and open-pit methods. A typical primary molybdenum ore body contains 0.05–0.25% Mo, and secondary ore bodies (copper porphyry ores) average 0.3–1.6% Cu and 0.01–0.05% Mo. Flotation remains the preferred and almost exclusive method of upgrading the molybdenite mineral to an industrial-grade molybdenite concentrate containing 90–95% MoS2, the balance being gangue (Habashi, 1997)."

Jan 1, 2016

By Jean-Sébastien Lambert, Serge Roberge

"At the end of 2014, Holcim Canada (Demix Aggregates Division) considered the possibility of drillingand blasting a big volume of rock in order to expose a high-quality limestone bench in one of their urbanarea quarries in Laval, Quebec (Canada). The project includes many challenges and has thus been qualified as a high-risk operation."

Jan 1, 2016

By R. Amata

"The Gakara Rare Earth deposit in Burundi (East Africa) is unique for its high grade (e.g., 54.3% TREO on average) and low uranium and thorium levels. The majority of the light rare earth (RE) elements in material from Gakara are contained within the familiar RE minerals bastnaesite and monazite. Extensive metallurgical test work was conducted by SGS Minerals Services on mineral samples collected from the Gakara deposit. Various whole ore hydrometallurgical processing routes were examined in a scoping level test program. Preliminary beneficiation testing was also conducted, though it was determined that only marginal upgrading would be achieved with significant RE losses. Thus a hydrometallurgical process on whole ore was developed to minimize the overall process complexity and achieve maximum RE recovery. Results from the test work will be presented, along with the selected base case flowsheet involving agitated atmospheric sulphation of the RE minerals, RE double sulphate precipitation, caustic conversion, redissolution, and carbonate precipitation. Following the base case flowsheet, a purified cerium free mixed RE carbonate with low levels of radioactive elements was produced.INTRODUCTIONRainbow Rare Earths Limited (Rainbow) is a mining company engaged in the exploration and development of the Gakara rare earth deposit in Burundi; Figure 1 shows the project location. The project is located in the Bujumbura Province and 45 km from the Burundi capital of Bujumbura. Notable for its exceedingly high in-situ grade – 54.3% on average total rare earth oxide (TREO), low uranium and thorium levels and familiar rare earth minerals, bastnaesite and monazite – Gakara is the world’s richest rare earth deposit. The project, a previously operating mine from 1948–1978, has a significant mineral inventory base, a long life of mine, well understood mineralogy, and robust economics. Rainbow is focused on bringing Gakara into production in the near term, ramping up to produce 5,000 t/y of a 54%+ TREO concentrate."

Jan 1, 2016

By F. Baerhold, S. Mitterecker

"Acid recovery is an important process step in pickling and leaching processes. Pyrohydrolysis in spray roasters and fluidized beds is a well-established technology to recover hydrochloric acid, but the hydrolysis in the liquid phase is more and more considered as an alternative new process route. The characteristic features of these three processes will be discussed along with select industry trends. For example, hydrochloric acid based leaching processes for ilmenite and nickel laterite ores produce far larger volumes of waste acid streams than the steel industry. Scaling-up of the spray roasting technology to the highest possible capacity is necessary in order to become more cost effective. In addition, process routes based on ferric chloride pyrohydrolysis allow the production of super-azeotropic HCl (up to 30 wt.%). Finally, the new ECOmode concept optimizes the operation of both pickling lines and the spray roast acid recovery plant. Long term results from industrial applications show that fuel savings in the spray roaster of 25% are easily achieved without additional process steps. An attractive feature is also to upgrade existing installations to higher plant capacities.INTRODUCTION Pyrohydrolysis is the conversion of metal halides into metal oxides at elevated temperatures in the presence of water vapor. Reaction products are a hydrogen halide gas and a metal oxide. The process was originally developed and introduced into the market by ANDRITZ Ruthner in the 1960’s. It has found wide technical application in the field of acid recovery and oxide production. The introduction of this process has revolutionized pickling technology. The use of hydrochloric acid has strongly increased over the last decades, since pyrohydrolysis is available for the total recovery of waste pickle liquors from mild steel pickling, as illustrated in Figure 1.Chloride media are also used increasingly in the metallurgical industry. Oxide production processes for Mg, Co, Ni, and Al have been installed. Processes using hydrochloric acid are known for the leaching of ores as well as for the re-extraction of metals from organic solvents. In both cases the recycling of HCl is of substantial importance to achieve highly economic processes and to reduce waste."

Jan 1, 2016

By S. Banisi, E. Arghavani, A. Akbari, Gh. A. Parsapour, S. Darvish Tafvizi

The new copper processing plant of the Sarcheshmeh copper complex consists of two parallel circuits. After a primary crushing, the ore is sent to a SAG mill and the product is further ground in a ball mill. The overflow of the hydrocyclones is fed to a flotation circuit which contains 8 rougher tank cells (RCS130), 3 cleaner cells (RCS50), 5 scavenger cells (RCS50) and a 4 x 12 m flotation column as recleaner. The circuit was initially designed to process a feed containing 0.8% Cu, but because of the ore type change, the feed grade decreased to 0.6% Cu. This resulted in a reduction of final concentrate grade and recovery from 28 and 85.5% to 24 and 84.4%, respectively. Based on the original design, the copper and silica recovery in the cleaner cells should be 69 and 55%, respectively, but these values increased to 85 and 75% because of a higher retention time. The rather high silica recovery (i.e., 75%) was found to be the main source of the lower final concentrate grade. In order to reduce the retention time of particles in the cleaner cell from 13.7 to 6.9 min, the rougher concentrates of two parallel circuits were fed to only one cleaner-scavenger and regrind circuit. This modification increased the cleaner and final concentrate grade from 15.1 and 24.5% to 17 and 26%, respectively. To prevent a possible reduction in the copper recovery, the froth depth in the scavenger cells was reduced. The overall outcome of the circuit modification was evaluated to be a 10% reduction in the energy consumption without any loss in the overall copper recovery.

Jan 1, 2016

By V. I. Ryaboy, S. A. Kondratyev

"The paper describes influence of desorbed species (DS) of a number of xanthates and higher dialkyldithiophosphates on the collective ability of these reagents. Adsorbed on mineral DS of the reagents in the form of products of non-stoichiometric interaction between xanthates and heavy metal salts can pass to the gas–liquid interface and remove liquid from the layer between mineral particle and water surface. A high-speed video recording displays the process of spreading of DS of xanthates and dialkyldithiophosphates over water at the moment of local rupture of the water layer. Expansion of “dry” spot on the mineral surface after DS of xanthate capture and displace liquid from the layer has been proved with video images. The comparative analysis of collecting ability and dynamic surface activity of dialkyldithiophosphates shows that these characteristics are in good correlation. The forces exerted by spreading film of the reagent’s DS on liquid in the water layer are evaluated, and the water flow rate from the layer is determined. The line of the reduction in thickness of the water layer behind the front of spreading film of DS of dialkyldithiophosphates and xanthates coincides with the line of the increase in their dynamic surface activity. Their force on the liquid volume in the water layer characterizes collecting ability of the DS film of xanthates and dialkyldithiophosphates. It has been supposed that the collecting ability of DS of a reagent is a part of its overall flotation activity, conditioned by surface tension of solution and, thus, defined by the structure of hydrocarbon fragment of the reagent.INTRODUCTIONIt is believed that collecting ability and selectivity of collecting reagents is mainly governed by adsorption of a reagent at the solid–liquid interface. A few studies have shown that activity of collecting reagents at the gas–liquid interface may have deep influence on their collecting capacity and selectivity. Experimental researches have revealed correlation between surface pressure in a carboxylic acid film on liquid’s free surface and floatability of useful components (Kulkarni & Somasundaran, 1975; 1980; Quast, 2006). According to Quast (2006), it is not always that surface pressure of a reagent film influences collecting ability of carboxylic acid. For instance, pH range of adsorption of tetradecanoic acid on hematite does not coincide with pH range of high surface pressure. So, surface properties of this acid contribute little to flotation efficiency.The correlation between reagent film surface pressure and mineral floatability has been reveled for quartz and cationic reagents, too (Bleier, Goddard, & Kulkarni, 1977). Finch & Smith (1973) showed that combination of adsorption of ion–molecular amine complexes on mineral surface and high surface tension of “fresh bubbles” was favorable for flotation performance. The use of bubbles with reduced surface tension resulted in a decrease in quartz floatability."

Jan 1, 2016

By Robin Dill, Wei Song, Andrew Perham, Leo Martin

"AECOM completed a subsurface exploration program for an 18-foot diameter, approximately 4-mile long rock tunnel project in Hartford, CT. The tunnel crosses the regional geologic trend through the middle of a sedimentary basin, passing through four separate rock formations, including two volcanic flows. Faulting is prevalent, with at least 15 faults encountered during the site investigation. Severe artesian flows were also experienced in several of the borings, requiring highly specialized drilling equipment. Sixty-two borings and associated testing were performed to characterize the structural geology, hydrogeology, rock properties and ground conditions. A phased program was carefully planned and implemented with participation of geotechnical and geologic specialists, with thoughtful evaluation along the way to react to the ground conditions encountered, and make appropriate refinements. This paper will discuss the subsurface program details; the integrated efforts used to effectively characterize the ground; and will summarize the final characterization presented in the GBR. PROJECT DESCRIPTION The South Tunnel Conveyance and Storage Tunnel project is part of the Metropolitan District (MDC’s) Long Term Control Plan to address discharges to various water bodies throughout the greater Hartford area. This program includes a main conveyance and storage tunnel; a tunnel boring machine (TBM) launch shaft and retrieval shaft; adit tunnels with associated drop shafts and connection structures; consolidation conduits and manholes; and a tunnel pump station (TPS) at the downstream end of the main conveyance tunnel. AECOM is serving as prime designer for the MDC on this project. The main conveyance tunnel (hereinafter referred to as the “South Tunnel”) will be a deep rock tunnel with an invert depth of approximately 180 feet at its downstream end and approximately 218 feet at the TBM retrieval shaft. The tunnel will have a finished diameter of 18 feet. The tunnel will rise in grade at a slope of 0.1 percent to its upstream end. Total invert depth along the deep tunnel alignment ranges from about 180 ft. to as high as 320 feet. The total length of the tunnel will be 21,754 feet. The South Tunnel will be constructed using a shielded TBM and fully lined with pre-cast concrete segments."

Jan 1, 2016

By Kirsten Corin, Margreth Tadie, Cyril O’Connor, Jenny Wiese, Wonder Chimonyo

"Relating flotation performance to the electrochemical characteristics of a pulp remains a complex issue both in fundamental research and in practice. For example, in the case of thiol collectors different Eh values can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by the control of pH and dissolved oxygen levels in the system. It is also possible to vary the potential by the addition of modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). The objective of the present study was to investigate the effect of the addition of the oxidising agents, NaClO and H2O2, on valuable mineral recoveries and grades in the flotation of sulphides from a PGM bearing Merensky ore. Batch flotation tests were conducted at pH 9.2, the natural pH of the system, in the absence and presence of a xanthate collector and Eh modifiers, viz. NaClO or H2O2. Most importantly in this way it was possible to vary Eh at constant pH and DO levels. The results indicate that in the absence or presence of xanthate the addition of H2O2 reduced both the recovery and grade of copper and nickel. In the absence of xanthate, the addition of NaClO improved the recovery of copper slightly and both the recovery and grade of nickel significantly, but in the presence of xanthate NaClO addition resulted in unchanged copper recovery and grade, but those of nickel were reduced. Based on anecdotal evidence that the addition of trace amounts of a potential modifier could improve flotation performance further tests were conducted the results of which suggest improved flotation performance.INTRODUCTIONIn the Merensky Reef, platinum group minerals (PGM) are commonly associated with base metal sulphides (BMS) and this has an effect on the way in which these minerals can be concentrated by flotation (Vermaak, Venter & Pistorius, 2004; Wiese, Harris & Bradshaw, 2005; Schouwstra, Kinloch & Lee., 2000). A major problem stemming from this association has been reported to be the loss of valuable minerals (PGM) associated with the loss of BMS (Wiese et al., 2005) during flotation. Shackleton (2007) suggested that PGMs behave in a similar manner to sulphides during flotation. Therefore, in order to recover the PGM, base metals are targeted. There is thus a need to investigate ways to improve the flotation performance of the sulphide minerals. The electrochemistry of the flotation of sulphide minerals has been studied for over half a century and there is consensus that sulphide minerals float only under a suitable redox environment (Heyes & Trahar 1979). This implies that reducing and oxidizing conditions during flotation of ores such as Merensky can be manipulated/varied to achieve an optimum flotation response.During flotation, sulphide minerals interact with thiol collectors in an electrochemical reaction to form hydrophobic species at the mineral surface (Finkelstein & Goold 1972; Rand & Woods 1984). The sulphide minerals are semiconductors and their interaction with collectors involves transfer of electrons. As such, a potential difference results which is responsible for driving electrons between reacting species (Fuerstenau, Jameson & Yoon, 2007). The magnitude of the potential difference affects the relative energies of charge carriers (electrons) at the mineral/solution interface hence controlling the direction and rate of charge transfer or rate of reaction (Bard & Faulkner, 2001). In a mixed mineral system the mineral/solution interface potentials account for the mixed potential which is critical to the process of flotation (Chander, 2003; Woods, 2003)."

Jan 1, 2016

By Matthew Wilcock, Kenichi Soga, Peter Wright

"This paper discusses how an existing grey cast iron segmental tunnel lining responds to construction of a new SCL tunnel transversely beneath with zero clearance; how the damage assessment for the existing tunnel was conducted for impact of longitudinal movement; how the tunnel is subsequently instrumented to observe both movement and stress manifestation at its longitudinal connections and how the results from the instruments compare with the prediction. An assessment of neutral axis of the tunnel in longitudinal flexure is also explored using interpolated horizontal displacement data from a conventional monitoring system. INTRODUCTION The Royal Mail Tunnel (RMT) (formely Post Office Tunnel or ‘Mailrail’) was constructed using semi-mechanised deep level construction techniques from 1914 and 1917 (Lee 1938). Commencing full commercial operation in 1926, the system was until 2003; conveying parcels the 6.5 miles between seven sorting offices in the center of London, and linking the system with main line rail stations, Paddington and Liverpool Street (The British Postal Museum & Archive 2013). A single tunnel of 2.74m internal diameter facilitated a bi-directional twin narrow-gauge (~611mm gauge) railway road system for electric driverless operation. The tunnel lining is segmental grey cast iron (grade 10) made up of six flanged segments and a smaller flanged key segment; constructed into a ring of width 508mm The external diameter of the tunnel is 2.971m. For further details of the tunnel lining and material properties are outlined by (Devriendt & Alhaddad 2014).London Underground Bond Street Station is a major station of the London Underground system in the very center of London; in its vicinity, the RMT runs west-east perpendicularly above the north south Jubilee Line tunnels. Historic survey record of the Jubilee Line’s (the then Fleet Line) construction in 1974 and its impact on the RMT case is documented in (Crossrail 1993): it is one of only a hand full of case-studies frequently cited when assessing the impact of new construction scenarios of this type; not least including the assessment of the same tunnel, at the same site some 40 years later, and the subject material for this paper: It noted significant vertical displacement of ~90mm to the RMT without noticeable serviceability or operational impediment."

Jan 1, 2016

By A. Ducastel, S. Connemann, A. Stark, F. Bouillot, C. Fricke-Begemann, LSA, H. Knapp, L. Horckmans

"Refractory materials are essential for all high-temperature applications in industry. Depending on the position in the furnace and specific process requirements, refractories are produced from several raw materials, such as dolomite, magnesite, bauxite, graphite or chromite. Most of these raw materials are not rare but strict quality requirements limit the producers of refractories to only a few deposits in the world. Thus, raw material supply is a critical factor for the production of refractories and accounts for 40-50 % of the total costs of refractories.A possible way to lower dependency on raw material supply is recycling of spent refractories. Main challenge in recycling is the separation of different brick types from each other and the removal of impurities, such as steel or slag. The European FP7 project REFRASORT aims to apply sensor-based sorting for separation of spent refractories. Sensor-based sorting is known from food industry, recycling and mineral processing and has proven its reliability. Nevertheless, some adjustments are necessary compared to applications in mineral processing because of other sensor-types and a higher number of products in one sorting step. This paper presents the results of feasibility tests for sensor-based sorting of refractories with near infrared spectroscopy and laser-induced breakdown spectroscopy (LIBS). Both sensors showed the potential to identify different brick types but the most promising results were obtained using LIBS technology. INTRODUCTIONRefractories are solid, ceramic products, which can sustain temperatures of more than 1500°C, without losing their stability or shape. Bricks of refractories have to withstand corrosion in contact with liquid steel or slag. Various high temperature applications, such as the production of glass, steel, copper or cement, require high quality refractories. The quality requirements of refractory bricks are strict, because small impurities can lower the thermal strength significantly."

Jan 1, 2016

By M. P. Sinha, Rashmi, Tata Steel Ltd., S. Jaiswal, A. Bhatnagar, P. Garg

Reagents form a crucial part of flotation process as they have the power to control the surface properties of minerals. In case of coal flotation, collectors and frothers are two the important and commonly used reagents. But other types of reagents such as promoters, modifiers and depressants are also finding wide applications because of their availability to improve selectivity and increase recovery. Because of these chemicals the scenario has changed from flotation being used mostly for high rank hydrophobic coals to low rank, oxidised or inferior coals. In the present work a case is presented in which two non-ionic surfactants (abbreviated as A & B) known to act as emulsifier have been studied to get a better flotation performance for a preparation plant with varying feed characteristics. Laboratory flotation tests were conducted with both the surfactants using three feed samples of the plant by varying the dosage at three different levels. The highest combustible matter recovery (more than 80%) was obtained for surfactant B at a dosage of 75 ppm (parts per million) for feed 1. But at the same dosage the recovery decreased by 21% and 10.2 % respectively for feed 2 and 3. On the other hand surfactant A showed a consistent result for all the three feed samples giving the highest value at a dosage of 50 ppm followed by a decrease beyond this point. The tests were complemented by contact angle measurements that demonstrated the same trend. In addition to this the reproducibility of data for Surfactant A was checked and found that the standard deviations for both separation efficiency and combustible matter recovery were within the permissible range (less than 5%). Finally an in-plant process optimization study to evaluate the performance and applicability of surfactant A at industrial level was done and has been discussed.

Jan 1, 2016

By Philip Antunes, A. E. (Tony) Reschke

"INTRODUCTION Tunnel Boring Machine (TBM) operations require the injection of material into the annular tail voids as the machine advances ahead of the segmental concrete lining. This annular gap is created because the cutting diameter of the TBM has to be larger than the outer diameter of the concrete segments of the tunnel lining. Fundamentally, the two basic types of annular grout are thick, concrete like mortars and thin, mobile, two-component grouts. While some European countries seem to still favor the concrete like mortars, from a global perspective it is now the two-component type grouts that dominate the industry. Two-component type grouts are comprised of an “A” component grout (typically cement, flyash, bentonite and a retarder/stabilizer) and a “B” component accelerator (sodium silicate or water glass as it is sometimes known). They are thus sometimes referred to as A/B type or bi-component grouts and were pioneered by the Japanese over 30 years ago. They offer a host of operational benefits over thick mortars, such as reduced settlement (Feddema et. al., 2001), effective penetration of the void space, with less energy, and reduced strain on the segmented linings (Robinson et. al., 2007). Two-component grouts are highly mobile and can be pumped many kilometers. The use of a retarder/stabilizer can also extend the shelf life of the “A” component grout for several days while the early strength of the accelerated grout stabilizes the ground and supports the segmental liner almost immediately. The batch plants that prepare the two-component grouts use one of two possible mixing methods for preparing the “A” component grout. The simplest plants use paddle type mixers and numerous tunnels worldwide have been successfully grouted using this technology. However, a superior type of mixer is available, namely the high shear colloidal mixer. Keller Colcrete successfully pioneered the development of the colloidal mixer back in 1937 and for over 75 years colloidal mixers have been internationally recognised as the most efficient method of mixing cement based grouts (Houlsby, 1990). These mixers are used in grout preparation for radioactive waste encapsulation, hydro dam grout curtains, soilcrete jet grouting, soil nailing, and numerous other geotechnical applications. In tunnelling, these mixers are also used for ground treatment, compensation grouting and for the preparation of bentonite lubrication for pipejacking. It has been only within the last decade however that these high-shear colloidal mixers have been adapted for use in the preparation of two-component grouts."

Jan 1, 2016