Search Documents

By Erik S. Bernard

"INTRODUCTION Reinforced Concrete (RC) members such as beams and columns are usually required to include stirrups to maintain post-crack shear capacity, and some may include stirrups that act as confining steel to maintain structural integrity during a seismic event (eg. NZS3101, ACI 318). To achieve seismic resistance, the spacing between stirrups is usually required to be much closer than is ordinarily prescribed for non-seismically resistant structures. Each stirrup must also fully enclose the longitudinal reinforcement with long end-hooks to ensure that the contained concrete is sufficiently restrained during reverse-cycle loading and the reinforcing bars are confined to prevent buckling. The close spacing between stirrups can lead to congestion of reinforcement within members, and can also be expensive to construct due to the labor-intensive nature of steel fixing. A possible alternative to closely-spaced stirrups is the use of fibers to provide restraint and confinement during a seismic event, although this is not yet recognized in codes. Previous experimental research (Jiuru et al, 1992; Filiatrault et al, 1995; Bayasi and Gebman, 2002; Billington and Yoon, 2004) has demonstrated that steel fibers are relatively effective in this application, but suffer the problem that their stiffness can make them difficult to consolidate within an already tight reinforcement cage, especially if they are relatively long (>40 mm). Moreover, steel fiber reinforced concrete (SFRC) is subject to embrittlement with the passage of time, leading to a steady loss of ductility beyond crack widths of 1-2 mm (Banthia and Trottier, 1994; Bernard and Hanke, 2002; Bernard, 2014; Bjontegaard et al, 2014; Bernard, 2015). Since cracks during seismic events are generally much larger than this, embrittlement may present a challenge to the long-term efficacy of SFRC during seismic events. An alternative to steel fibers for enhancement of seismic resistance is the use of macro-synthetic fibers. This type of fiber usually offers the advantage of being flexible so that consolidation is easier between reinforcing bars. They also offer superior durability compared to steel fibers and can reduce flexural crack widths (Bernard, 2016). Several recent small-scale investigations (Ma et al, 2012; Carnovale, 2012; Osorio et al, 2014) have indicated that macro-synthetic fibers can produce meaningful improvements in seismic resistance if used in combination with conventional steel reinforcing bars. The present investigation has extended research in this field by examining whether embossed macro-synthetic fibers can be used to increase the spacing between stirrups while maintaining seismic resistance."

Jan 1, 2016

By Mohamad Sabsabi, André Hamel, André Moreau, Paul Bouchard

"Laser-Induced Breakdown Spectroscopy (LIBS) is an atomic spectroscopy technique used to measure elemental concentrations. It is well-adapted to in-situ and in-line measurements during materials processing in general, and pyrometallurgy in particular. It is an optical non-contact technique and it can measure nearly all elements, including light elements. Our group has developed a mobile prototype system to measure molten metals. The system includes a tube, also called a lance, one end of which is immersed in the molten metal. An inert gas flows in the tube and bubbles out below the surface. The LIBS measurement is made through the tube and onto the bubble’s surface. This is done to avoid measuring contaminants, slag, or fluxes often found at the surface of the melt. An added benefit is that the molten surface is constantly renewed and thus, more representative of the bulk. An alternative to using our lance is to use a tuyère, such as a gas injection tuyère in a converter, as we did several years ago in a nickel matte converter. In this presentation, we will show various applications emphasizing more recent developments. This includes the simultaneous measurement of the concentrations of Cu, Ni, Fe, Co and S in molten matte at 1125 °C. The more obvious industrial applications of the technology include determining the best time to end oxygen blowing in the converter and elemental concentration measurement during alloying.INTRODUCTIONThe mining industry continually faces challenges in optimizing cost and productivity. Because of the large volumes of materials that are being processed, small improvement can have a big impact on benefits. Better real-time information can help improve this optimization."

Jan 1, 2016

By Alejandro Ferrada Vergara, Héctor Espinoza Muñoz

Drilling and blasting stages are considered factors that impact downstream processes significantly and over all the mining business value chain. Adequate control of these processes may represent energy savings in comminution processes. There has historically been a resistance to design change as this implies more drilling and implementation costs due to new technologies in explosives, which added value is difficult to quantify.

Jan 1, 2016

By N. Moemise, M. B. Shongwe, P. A. Olubambi, M. M. Ramakokovhu

"Near-infrared (NIR) spectroscopy sorting technology is incorporated in an automated optical mineral sorter that can discriminate between materials using the differences in characteristics when exposed to near-infrared radiation. During September 2014 to April 2015, a pilot plant that utilized NIR technology to discriminate between kimberlite and waste materials was commissioned to determine the viability of including this technology in the diamond winning process flow sheet at Cullinan Diamond Mine. The plant was used to minimize the waste content in the size fraction -70+35 mm that reports to the crushing section and then to the dense media separation process. This paper describes the initial test work, conducted at Mintek, that led to the decision to conduct a pilot-scale study. The mineralogical characterization of the feed and product streams to establish the sorting criteria and the operational data obtained during the pilot plant campaign are described. The results indicated a good possibility of discriminating between the kimberlite and waste material using NIR technology. However, the consistency of discrimination was not good enough to avoid the risk of potential diamond loss. Furthermore, a lower than expected availability of the machine reduced the throughput capabilities. IntroductionUsing near-infrared spectroscopy (NIRS) technology for ore sorting is a new concept for the mineral processing and mining industry. NIRS has been used for decades in the laboratory for the identification of pure minerals, and has its roots in the recycling, food, and pharmaceutical industries (Salter and Wyatt, 1991; Robben et al., 2009). Ore sorting in itself is not a new concept; it was introduced during the Stone Age with handsorting being the first method to separate valuable materials from gangue (Wills and Napier-Munn, 2006; Sassos, 1985). However, over the years the scale of mining has increased and hand-sorting has become challenging to implement (Joensson, 2014).Sensor-based sorting is an advanced technology that can help overcome problems such as ore dilution experienced in mineral processing operations. The benefits are lower energy and water costs, reduced ore dilution, lower environmental impact, and improved profit margin (Mathew, 1974; Jonsson, 2014; Salter and Wyatt, 2009; Death et al., 2009). In sensor-based sorting, materials are mechanically sorted based on certain physical properties that are detected by a sensor (Dalm, 2013). Research has found that with NIR scanners it is possible to obtain a ‘fingerprint’ of a sample that is directly related to its mineralogical composition. According to Woutruba et al. (2009), molecules absorb NIR radiation by means of electronic and vibrational transitions. Nowadays, there are many sensors available in the market that utilize different material properties; the choice of a sensor is dependent on the mineralogy of the ore."

Jan 1, 2016

By Akiyoshi Horiuchi, Manabu Kanno, Shigeki Sato, Taro Aichi

"AKITA ZINC Co., Ltd. (Iijima Zinc Refinery), jointly owned by DOWA METALS & MINING Co., Ltd.(DMM), has used the company’s own hematite process for iron control since the beginning of operations in 1971. The hematite process consists of reductive leaching with SO2 gas and iron removal in autoclaves by high temperature hydrolysis. This process enhances not only zinc recovery but also the recovery of gold, silver, copper, lead and rare metals, which is carried out at another DOWA metallurgical plant. All by-products produced in the hematite process are marketed and sold. This paper presents an overview of the hematite process and the recent process improvements made.INTRODUCTION DMM carries out mining and smelting activities for precious metals, PGMs, rare metals and base metals such as copper, lead and zinc. It owns KOSAKA SMELTING & REFINING, producing copper and lead, and the AKITA ZINC Co., Ltd. (AZC) in Akita Prefecture. DOWA is a specialized smelting company which has established a metallurgical complex for copper, lead and zinc, including a recycling business. AZC was established in 1971 at a production capacity of 72,000 t/y zinc; it is jointly owned by DMM and five other non-ferrous metal companies. AZC has increased its capacity continuously and now produces 210,000 t/y of zinc. Figure 1 shows the changes in zinc production and capacity at AZC."

Jan 1, 2016

By Takayoshi Otsuka, Taher Elsamni, Ashraf Bou-Krisha, Takaya Takimoto

"INTRODUCTION Tunnel is a closed space structure and it is necessary to ensure the sufficient time and route for safe evacuation for the tunnel users in case of a tunnel fire. In order to do so, damages and collapse of the tunnel linings and the secondary disasters can be avoided. Furthermore, the road tunnel is one of important infrastructural facilities and stopping its function for a long time for a tunnel fire could cause a great economic loss. Therefore, the tunnel structure shall be the one which can be repaired as soon as possible, and the fire protection methods need to be selected among those which enable the service to start as early as possible. The necessity of the fire protection works is evaluated for the tunnel structure with the consideration of the expensive tunnel construction cost and the economic effects of the tunnel service. Naturally, the fire protection works, which can protect the tunnel linings from the tunnel fire with small repairs, are inevitable. Design engineers of the fire protection works estimate the scale of fire from the degree of damages on the linings and its repair cost, the effect of fire extinguishers placed inside of the tunnel, the secondary disasters in accordance with the tunnel lining damages if any, and the ratio of fire protection cost calculated from tunnel operation cost. Based on this information, the engineers design the fire protection works according to the permissible limits Among the design cases of the tunnel fire protection in Japan, as shown in Table 1, there is no cases that used the fire temperature-time curve to design the fire protection works for large fire caused by vehicles catching fire. However, the most of cases used 30-60 minutes for fire duration based on the entry prohibition of dangerous goods carrying vehicles or the effect of early fire fighting. This paper will study the variation between different methods used for fire protection in road tunnel in Japan to evaluate them and try to found some recommendations. Especial l care will be attention to Polypropylenes (PP) which is starting to be applied lately."

Jan 1, 2016

By Andrew Cho, Changsoo (Kevin) Moon, Richard Flanagan, Brian Larsen

"INTRODUCTION Project Background The U.S. Army Corps of Engineers (USACE)/Port Authority of New York & New Jersey (PANYNJ), as part of their New York and New Jersey Harbor Deepening Project, will dredge this shipping channel to a depth of 16.5 m below mean low water (MLW). By deepening the channel, the new generation of larger, “post-panamax” container ships coming to U.S. waters as a result of the expansion of Panama Canal can be accommodated in local marine terminals, helping to retain the nearly 300,000 jobs and $12 billion in annual wages the PANYNJ provides to the region. The existing siphons are situated at a depth that could be compromised by the planned dredging of the channel (nycedc.com). The purpose of this project is to build a new 1.83 m diameter water main inside a 3.66m diameter tunnel replacing the two existing siphons in order to provide the necessary backup water supply to Staten Island across the Anchorage Channel within the Upper New York Bay from Brooklyn. The proposed tunnel is approximately 2.9 km long and at a depth of at least 26 m below MLW. The project is funded jointly by New York City’s Department of Environmental Protection (NYCDEP) and PANYNJ and is managed by New York City Economic Development Corporation (NYCEDC). The contractor of the project is Tully/OHL JV, the designer is CDM/HMM JV, and the CM is LiRo/PB JV. History of New York City’s Soft Ground Tunneling The New York City area has a relatively long history of soft ground tunneling, commencing in the late 19th century. Construction of the first Hudson River tunnel crossings was begun (but not completed) in 1874 for the Hudson & Manhattan Railroad using compressed air supplying a shield. The work continued intermittently until the project finally opened for service in 1907. These 1.72km long tunnels (maximum depths of 29 m) are still in operation and now operated as the PATH Tunnels. They are approximately 5.5m diameter utilizing cast iron segments. The river bed consisted of primarily silt with shallow rock near the New York side. Air “leaks” occurred during the compressed air excavations resulting in some serious “blows” with water and soil entering the tunnel, including one incident with 20 deaths."

Jan 1, 2016

By Braden Lusk, Paul Sainato, Josh Calnan, Hiago Vasconcelos, Luis Felipe Marinho

"Blasting and rock fragmentation is one the most important unit operations in mining. Since itsintroduction into the mine production cycle, mining has become more efficient in mineral production(Hartman, 2002). Widely used with the main objective of breaking rock mass in smaller fragments to be loaded and hauled at a minimum cost, blasting is optimized when stemming materials properly confine drillholes charged with explosives. Halim Cevizci (2013) performed a stemming application using Gypsum plaster, a kind of material that exhibits solid-like behavior when it is dry. Based on his theory, the present article reports an experiment using another type of material that shows similar behavior, non-Newtonian fluids. The primary goal of this study is to measure the confinement effectiveness provided by a non-Newtonian mixture as the stemming component. The study also analyzes the explosives’ energy propagation throughout the rock mass relating to the stemming materials applied. Currently, mining literature recommends the application of dry granular materials in stemming columns, because of its inertial and high frictional effects (Hagan, 1973). However, the test verified that the mixture added to the stemming column was able to reduce energy and gas losses to the atmosphere, because of the liquid’s property of filling voids in the material. The solid-like behavior of the non-Newtonian mixture was investigated for its capability to improve borehole confinement, since the mixture reacts like a solid when under shear stress. The results were compared to those from sand and air stemming applications, configured in different arrangements. It was concluded that the non-Newtonian mixture yielded high results due to its better confinement effectiveness, a reduction of air overpressure, and an increase of the strain propagation and ground vibration throughout the rock."

Jan 1, 2016

By S. Tuylu, D. Adiguzel, A. Bascetin, E. G. Savas, O. Ozdemir

"Paste Technology has some advantages comparing to other surface disposal methods. With this method, it is possible to pump high concentrated solid materials to very long distances without segregation problem. However, it is known from Literature that pumpability of materials is completely related to rheological properties of the materials. For this reason, in this study, the rheological parameters (e.g. yield stress and viscosity values) of the paste material prepared from Pb-Zn tailings at various solid ratios (60-85%) were obtained in order to determine the pumpability of the paste material. Additionally, slump tests, which are usually used in mining industry, was carried out. Finally, regression analysis was made between the slump values and rheological parameters of the paste material to find a correlation between two independent parameters. The results showed that there is a great correlation between the slump values and the yield stress of the material. On the other hand, there was no correlation with viscosity: ty=430.28-16.877Sv (R2= 0,94; ty: Yield Stress (Pa), Sv: Slump Value (cm)). Based on the results obtained from this study, it can be clearly concluded that the slump values obtained from a simple test can be used to predict yield stress values of paste materials. INTRODUCTION Recently, surface disposal of mining tailings has become one of the biggest problems in mining industry in terms of environmental issues. Therefore, several researches have been focused on this subject in order to find a best solution or method for this problem. These studies showed that paste technology has some advantages compared to other conventional methods. Tailings thickened to the extent show no segregation of particles during transportation, and relatively small amount of settling occur post-deposition which are often called “paste” (Cincilla et al. 1997). Paste tailing technology has two applications in the industrial area as underground paste fill and surface paste disposal. Paste tailing technology was first started to be used in Grund mine, Germany in the late 1970s (Grice, 1998). Process tailing material, water and - if needed - cement materials, which are the components of the paste, must be blended to obtain a homogenous mixture suitable for pumpability. Consistency behavior of the paste material is determined using a conventional sedimentation cone concrete test (slump). Meanwhile, the slump value of the paste must be between 200 and 250 mm for surface applications (Newman et al., 2001). Additionally, in the case of underground paste system, the optimum slump value must be between 150 and 200 mm. On the other hand, the water content and density of paste at certain slump value change depending on the amount of fine particles in the tailing sample. While moisture of the material will be high, its density will be low because of surface area of particles which increases with decrease in particle size (Meggyes and Debreczeni, 2006). For pumpability of the paste to long distances, slump value of the paste must be good enough to be accepted for use of surface paste disposal. Paste material has a yield stress because they show non-Newtonian behavior and generally is classified as a Bingham plastic fluid. (Cooke, 2008; Theriault, 2003). In addition, the appropriate viscosity value of the paste along with the yield stress must be between 100 and 250 Pa (Bascetin et al., 2013; Bascetin et al., 2014; Bascetin et al., 2015)."

Jan 1, 2016

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. Contrary to most copper sulfide minerals where recovery is principally liberation controlled, the recovery of molybdenite is much more complex with fully liberated particles commonly lost to tailings. It is this complexity that facilitated the necessity for a geometallurgical investigation of molybdenite from the Bingham Canyon deposit. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes (i.e. morphology, angularity, liberation, size) have on the recovery of molybdenite in the processing circuit. A set of samples was collected from the ores and products produced by Rio Tinto Kennecott’s Copperton Concentrator. All samples were analyzed using normal polarized reflective light, Mineral Liberation Analyzer (MLA) and X-ray diffractometery (XRD) techniques. The results of this investigation revealed the presence of two distinctly different types of molybdenite, which have been identified as the two polytypes of molybdenite, i.e. hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the core of the Bingham Canyon deposit. The 3R polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Concerning their metallurgical behavior each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. For instance, the 2H polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high quality molybdenum concentrate under normal operating conditions common to most copper concentration operations. In contrast, the 3R polytype is difficult to grind and kinetically “slower” floating with surface attributes that less amenable to recovery under normal operating conditions. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to the normal operating parameters may be necessary to improve the recovery of molybdenum. Finally, a preliminary investigation into the metal budget of porphyry Cu and Mo deposits indicates that a positive correlation may exist between the total economic metal budget and the polytype content. For example, higher concentrations of the 3R polytype appear to be more prevalent in Au-enriched porphyries versus Mo-enriched porphyries. This observation may also serve to help explain why it is easier to obtain high rates of recovery in Mo ± W-rich deposits, which contain little to none of the 3R-polytype. Consequently, the potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present, as well as its impact on the economics (exploration) and/or on the processing circuit (plant design) could exist. In conclusion, this investigation highlights the necessity of understanding the mineralogical properties or characteristics of molybdenite and/or other economic mineral(s), as these can and will have a direct impact upon the performance and plant optimization."

Jan 1, 2016

By Longjiang Li, Song Mao, Zhengyang Qiao, Qin Zhang, Guizhou University, Ling Wang

"After a study on the advantages and disadvantages of flotation column, according to the limitation of ordinary flotation column only is used for a flotation of microgranular minerals, the paper designed a new kind of layered convection coarse particle flotation column.Using a bauxite to test the rationality of the flotation column.The test results show that the new layered convection coarse particle flotation column is feasible.It has certain advantages about coarse particles flotation.INTRODUCTIONFlotation column has many advantages, for example,a simple structure, high efficiency and energy saving, the obvious advantage of fine particles flotation , the index superior and so on. The advantages gradually getting people's recognition. Research of flotation column has been a breakthrough, however, due to it only is used for the flotation of microgranular minerals, and the microgranular mineral particles will lead to a series of problems, and makes the processing cost is increased. Due to increase grinding fineness can save the grinding time and reduce the cost of grinding, also can avoid the disadvantage of fairly granular mineral particles cause a deterioration in the flotation. So it is necessary to research a kind of coarse particle flotation column.After a research on the advantages and disadvantages of flotation column, the authors designed and manufactured a new layered convection coarse particle flotation column, the flotation column both in theory and operation is better than flotation machine.DESIGN OF THE LAYERED CONVECTION COARSE PARTICLE FLOTATION COLUMNAdvantages and Disadvantages of the Traditional Flotation ColumnIn the field of mineral processing, as the increasing proportion of ore that has low grade, fine dissemination size, complex mineral composition characteristics. The limitations of traditional flotation machine is increasing[1],for instance, the high energy consumption, severe wear, inconvenient configuration , large amount of maintenance and so on. Compared with flotation machine, the flotation column with high separation efficiency, low investment and production cost, covers a less area low installation cost, less reagent dosage, more suitable for separation of fine particles and can automatically control, etc[2]. At present, the ore is facing the world energy crisis situation, and becoming increasingly difficult to flotation. So it is important to invent a coarse particle flotation column."

Jan 1, 2016

By M. Rahmanpour

"Mine planning is a multidisciplinary procedure that aims to guarantee the profitability of a mining operation in changing and uncertain conditions. Mine plans are normally classified as long-term, intermediate-term, and short-term plans, and many factors affect the preciseness of these plans and cause deviations in reaching the objectives. Commodity price is the heart of mine planning, but it has a changing and uncertain nature. Therefore, the determination of mine plans in the presence of uncertain mineral price is a challenge. A robust mine plan reduces the risk of early mine closure. A procedure is presented to determine the value at risk (VaR) in any possible mine planning alternative. VaR is considered together with downside risk and upside potential in order to select the most profitable and least risky plan. The model is tested on a small iron ore deposit. IntroductionMining projects are normally evaluated with the objective of maximizing economic value, as measured by the net present value (NPV). The aim of mine planning is to develop a yearly extraction plan that guides the mining operation to the highest NPV (Dagdelen, 2007; Yarmuch and Ortiz, 2011). This plan considers the technical constraints such as blending requirements, block sequencing, and pit slope (Caccetta and Hill 2003). Thus, the mine plan affects the economics and the payback period of mining operations.Mine planning is a procedure based on which the profitability of the mining operation is guaranteed in changing and uncertain conditions (McCarter, 1992). However, conventional mine planning ignores the volatility and uncertainty of future commodity prices and does not allow for managerial flexibility. It is common practice to assume a deterministic and constant commodity price through the mine life. The problem with this approach is that the commodity price is the heart of the mine planning procedure and governs the profitability and feasibility of the operation; thus ignoring price volatility will result in a sub-optimal mine plan."

Jan 1, 2016

By L. Vinnett, I. Panire, J. Yianatos, F. Ruiz

"The effect of operating variables on the flotation performance at steady-state has been extensively used for modelling and simulation of separation processes. However, the dynamic characterization of key variables such as gas dispersion (Sauter mean diameter of bubbles, D32, and bubble surface area flux, SB) and froth discharge rate is rather scarce. In this paper, an experimental design allowed identifying the dynamic response of the flotation process in a laboratory scale flotation cell, using a two-phase system, airwater. The installation included automatic control for the superficial gas rate, JG, and the pulp level. Gas dispersion was evaluated in terms of the Sauter mean diameter of a bubble population and the bubble surface area flux, SB = 6·JG/D32. The D32 was measured using the McGill Bubble Size Analyzer (MBSA) along with a semiautomated algorithm. In addition, the froth discharge velocity was measured in real-time using a Visiofroth system. The control variables were the superficial gas rate and the frother concentration (Teefroth). The dynamic characterization of the flotation process is useful to design algorithms that allow the direct or indirect control of metallurgical variables such as flotation rate, concentrate grade and mineral recovery.INTRODUCTIONGas dispersion indicates the way the gas entering a flotation machine is dispersed throughout the volume of the equipment (Schwarz & Alexander, 2006). The gas dispersion is typically characterized in terms of the bubble size (dB), gas holdup (eG), superficial gas rate (JG), and bubble surface area flux (SB =6·JG/dB) (Finch et al., 2000). All these variables have significant impact on the metallurgical performance of flotation machines. For example, Perez-Garibay et al. (2014) investigated the effect of the particle size, bubble size distribution, superficial gas rate and collector dosage on the flotation performance, for the separation of a sphalerite mineral. The authors observed that recovery increased with the superficial gas rate ranging from JG = 0.04 to JG = 0.08 cm/s and also a maximum recovery was obtained for bubble size close to 300 µm. Gorain et al. (1998) reported a strong correlation between the flotation rate constant and the bubble surface area flux in a zinc cleaner circuit. Both variables were directly proportional at three froth depths in the range of hF =7 - 45 cm. Dobby & Finch (1986) incorporated the effect of the superficial gas rate and the bubble size on the flotation efficiency by means of a kinetic model for the rate constants. Yianatos & Contreras (2010) developed a model to estimate the carrying capacity in large flotation cells by including the bubble surface area flux."

Jan 1, 2016

By M. U. Khan, A. D. S. Gillies

"Diesel exhaust is a major cause of large number of occupational diseases. Acute and continuous exposure to Diesel Particulate Matter (DPM) can cause numerous health issues including respiratory disease, reduced lung capacity, heart disease etc. The National Institute of Occupational Safety and Health (NIOSH) and the International Agency for Research on Cancer (IARC) consider diesel engine exhaust as carcinogenic. In large underground metal and nonmetal mining operations, regulatory compliance regarding miner’s exposure to airborne particles especially DPM is a big challenge. Complex mine networks add more difficulties in controlling DPM. MSHA relies on the NIOSH 5040 method for DPM compliance. The NIOSH 5040 method is a shift average based method which inherits some limitations. Due to these inherent limitations of the NIOSH 5040 method the concept of real-time DPM monitoring is promoted in the mining industry. Several real-time DPM monitors have been used by the researchers and efforts still continues to improve their measuring techniques and understanding. Real-time monitoring of DPM is vital to gain understanding of rapid changes in the mine atmosphere. The current study highlights the advancement in real-time DPM monitoring and mainly covers a review of several studies in which DPM concentrations were measured by utilizing real-time DPM monitors. INTRODUCTION Ventilation of underground mines is an important aspect of mining operations. Mining is a continuous activity and the ventilation networks in modern mines change with extended developments. Proper understanding of the ventilation network is a key design factor of an optimum mine ventilation plan. An important task of underground mine ventilation engineers is to provide clean air with sufficient quantity to the underground miners (Khan M. U. and Gillies A.D.S. 2015). The amount of fresh air supplied to the mine should be adequate to dilute the concentrations of contaminants present in the mine atmosphere. In the United States it is estimated that diesel powered equipment is used in thousands of mining operations (Stephenson D. J. et al. 2006). Use of diesel powered equipment is an attractive option in underground mines due to its several advantages over other available alternates. Diesel engines are rugged, dependable and fuel efficient (McKinnon 1999). It is common for diesel engines in heavy duty trucks to have a life of 1.6 million kilometers (McKinnon 1999). Looking at the developments in other energy alternatives, it can be assumed that the underground mining industry will maintain its reliance on diesel powered equipment (Anon 2001). DPM is an important source of mine air contamination in many non-gassy underground mines (Khan M. U. and Gillies A.D.S. 2015). Diesel exhaust is harmful for humans. Acute and continuous exposure to diesel exhaust concentrations can cause several health issues. Some of the health diseases caused by DPM exposure are respiratory diseases, reduced lung capacity, heart disease, and lung cancer (National Research Council. 1981, Mine Safety. 2005). In addition, NIOSH regards diesel exhaust as “potential carcinogen” (Centers for Disease Control 1988) and IARC has declared that “diesel engine exhaust is carcinogenic to humans” (IARC 2012). NIOSH has also declared that the reductions in DPM exposure would reduce cancer risks (Centers for Disease Control 1988)."

Jan 1, 2016

By Tom C. Palangio

Commercially available online particle size analyzers (OPSA) are in their third decade of development (Palangio, T.C., 1985), (Franklin, J. A., Maerz, N.H., 1987), (Maerz, N.H., Franklin, J.A., and Coursen, D.L., 1987). The installed base of operating analyzer numbers is in the hundreds. This paper takes a look at five critically important relationships that users have discovered through the use of OPSA systems. The two key attributes of these systems are: 1) consistency and, 2) historical context compared with traditional practices.

Jan 1, 2016

By Elena Chiriotti, Federico Valdemarin, Jan Cenek

"SUMMARY The “28 May Station” is the only transfer station between the existing Green and Red metro lines in Baku. As part of the huge development strategy of the metro network, the complete separation of the existing underground lines has been planned at this location, in order to simplify the operation of the future metro system. The extreme challenge of the project is represented by the need of achieve the separation of such lines over a breakdown of the operation of just five weeks. The lack of direct access from the surface, a complex geology with artesian water layers, a congested underground space and sensible buildings represent additional constraints. The chosen design solution consists in creating a complex steel pipe jacking frame around the operating tunnels and then excavating under such frame two large caverns where the separation of the existing lines and the construction of the new metro tunnels will be achieved. Soil treatments have been conceived to mitigate the geotechnical risks and to reduce possible impacts on the existing structures. The paper illustrate the challenges of this extraordinary project, one of the most complex underground structures under study, the design solutions and the risk management approach used to manage the complexity and to design the mitigations measures. INTRODUCTION The metro network in the capital of Azerbaijan is rapidly growing together with its metropolitan area. The beginnings of the existing metro system started in Baku in 1967 in Soviet times. To date, only two lines (Green and Red) are in operation with a total length of 34 km, including 23 stations. The future network will be much wider: besides the construction of three completely new lines and the extension of two existing lines, the whole metro project includes the development and modernization of the existing metro sections. A consortium formed by Systra (leader), Mott MacDonald (Praha) and Saman (Korea) awarded the contract for the preliminary and detailed design of infrastructures for the extension of Baku Metro Network. This extension consists in 83 km of new lines and extension of existing lines. As part of this modernization project, the connection of the Green Line at the 28 May / Cefer Cabbarli Stations, focus of this paper, represent also it’s ""Achilles' heel"" given that the already very congested system have only one transfer station."

Jan 1, 2016

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016

By Jessica M. Wempen, Michael K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DlnSAR), a satellite-based remote sensing technique, has potential application for measuring mine subsidence on a regional scale with high spatial and temporal resolutions. However, the characteristics of Synthetic Aperture Radar (SAR) data and the effectiveness of DlnSAR for subsidence monitoring depend on the radar band (wavelength). This study evaluates the effectiveness of DinSAR for monitoring subsidence due to longwall mining in central Utah using L-band (24 cm wavelength) SAR data from the Advanced Land Observing Satellite (ALOS) and X-band (3 cm wavelength) SAR data from the TerraSAR-X mission.In the Wasatch Plateau region of central Utah, which is characterized by steep terrain and variable ground cover conditions, areas affected by longwall mine subsidence are identifiable using both L-band and X-band DlnSAR. Generally, using L-band data, subsidence magnitudes are measurable. Compared to X-band, L-band data are less affected by signal saturation due to large deformation gradients and by temporal decorrelation due to changes in the surface conditions over time. The L-band data tend to be stable over relatively long periods (months). Short wavelength X-band data are strongly affected by signal saturation and temporal decorrelation, but regions of subsidence are typically identifiable over short periods (days). Additionally, though subsidence magnitudes are difficult to precisely measure in the central Utah region using X-band data, they can often be reasonably estimated.INTRODUCTIONDifferential Interferometric Synthetic Aperture Radar (DlnSAR) is a satellite-based remote technique that can be used to measure surface displacement over large regions with high spatial resolution. Under good conditions, displacements can be measured with centimeter to subcentimeter accuracy (Buckley, 2000; Massonnet and Feig!, 1998). DlnSAR also has high temporal resolution, and imaging periods typically range from 10 to 50 days (Rosenqvist, Shimada, and Watanabe, 2004; Roth, 2004). In the last two decades, the application of DlnSAR for mine subsidence monitoring has been demonstrated in coal basins in Europe, Australia, China, and the United States (Camec and Delacourt, 2000; Ge, Chang, and Rizos, 2007; Ge et al., 2008; Ismaya and Donovan, 2012; Ng et al., 2010; Perski, 2000; Perski and Jura, 2003; Popiolek and Krawczyk, 2006; Wegmuller et al., 2005; Wright and Stow, 1999; Zhao et al., 2014; Xinglin et al., 2014). Overall, these studies have demonstrated good data resolution, strong relationships between mine development and subsidence, and reasonable agreement between displacements measured by DinSAR and displacements measured by conventional surveys."

Jan 1, 2016

By Missy Isaman

"Mixed ground tunnels come in all kinds. In rock tunnels with possible faults and high pressure water, the challenges are many. With the advent of Crossover TBMs, contractors can minimize machine wear in such conditions while maximizing efficiency. The newest generation of Crossover is exemplified by two projects in Albania and Turkey. A 5.56 m Crossover TBM destined for Turkey’s Gerede Water Transmission will be assembled using Onsite First Time Assembly (OFTA) from within an existing tunnel. The unique machine will bore through 30 fault zones requiring the TBM to be sealable to up to 20 bar so pre-consolidation grouting can be done. If boring under pressure is required, the TBM will bore sequentially using the screw conveyor fore and aft gates. Skewing further towards hard rock, a unique 6.2 m diameter Double Shield TBM with Crossover features was designed for Albania’s Moglicë Headrace Tunnel. The machine features closure doors and a sealing system to contain inrushes of water until they can be grouted off. This paper will discuss the unique aspects of the Crossover designs, including their inception as based on past projects in difficult ground, and their utilization at the two current projects. INTRODUCTION Specialized tunnel boring machines have been made for years to tackle specific types of ground conditions. Traditional types of TBMs bore within a specific set of ground conditions. If a project is located in a competent granite face, then a Main Beam machine is a good solution. In soft ground, Earth Pressure Balance (EPB) machines are the method of choice. Years of experience and engineering advancements have made both types of machines fast and economical solutions for tunneling. Unfortunately not all ground conditions are a perfect swath of one material, and the need for a more diverse machine is apparent."

Jan 1, 2016

By G. Deschênes

"In 2013, as the prices of precious metals dropped, investors moved their positions to equity markets for higher returns. As a result, the price of gold dropped further to below US$1200 per ounce, prompting additional substantial outflows from gold investments. In response to lagging gold prices, major gold producers initiated large asset write-downs and cost-cutting programmes. In 2015, this trend continues and gold mining stocks are close to lows not seen since the global financial crisis (GFC) of 2008. In the current economic climate many projects have marginal economics, and the number of projects that have competitive development and production costs is declining. A competitive edge is particularly important with the decreasing grades of orebodies, increasing complexity of the mineralogy, and increasingly demanding environmental constraints. In addition, higher cost producers seek to optimize their process t o reduce operating costs.This paper presents some highlights of three case studies on optimization of gold leaching strategies that improved the economics of brownfield projects. Processing of sulphide-bearing ores was optimized by using the synergy between cyanide, lead nitrate, and oxygen. The outcomes were significant reduction of retention times while maintaining or increasing gold extraction and reducing cyanide addition and effluent treatment costs. A stirred tank reactor experimental programme led to direct implementation of reliable leaching strategies from laboratory scale to production. This approach resulted in savings of $2.2 million to $15.2 million on the three brownfield projects discussed in this paper."

Jan 1, 2016