Search Documents

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2017

By Elard René Miranda Mecola

"El presente texto busca determinar un esquema extractivo para tratar minerales de ciertas características que permitan recuperar el cobre y el oro presente para el proyecto minero Romerillo ubicado en el distrito de Bella Unión, provincia de Caravelí, departamento de Arequipa. La estrategia de la investigación es tratar de separar extractivamente el cobre del oro, por lo que se efectúan pruebas de flotación para las especies de cobre sin encontrar éxito. Así se utiliza la alternativa de lixiviación ácida de cobre y posterior cianuración del oro contenido en el relave."

Dec 1, 2016

By Ken Goering, Steve Kral, William Gleason

"Once every four years, the global mining industry gathers in Las Vegas, NV for MINExpo International. According to the show’s organizer, The National Mining Association (NMA), about 44,000 people attended the three-day show from Sept. 26-29. It was a show that featured the latest and greatest in equipment and technology. It also served as the backdrop for a snapshot of the state of the industry and while the picture of a global industry is never completely clear at any one time, one thing that is evident is technology has become a major force in the way mining is done.Had it not been for the awe-inspiring “iron” that was on the show floor in the form of haul trucks and shovels weighing hundreds of tons, one could be forgiven for thinking that they were at the Consumer Electronics Show. From training simulators designed to give a realistic experience of operating mining equipment to virtual reality technology that can take the user into the depths of an underground mine or the middle of a mapped ore deposit, an overriding theme of MINExpo 2016 was that the mining industry is connected like never before.In the north hall of the Las Vegas Convention Center was the GE Mining booth that was designed to showcase its efforts to help create a mine that will be connected from the front office to the face of the underground wall or bottom of the openpit. GE Mining called its booth a digital mine, and it included a suite of technologies that can improve performance, reliability, safety and operations. GE Mining said it views each mine as a mini-city, requiring power, water and transportation. Intelligent, real-time monitoring across the mine allows operators to make data-driven decisions that improve equipment reliability and optimize mine operations for substantial savings. And GE Mining was just one of many exhibitors showing off software that allows various types of equipment to communicate. Its booth sat in the shadow of the Komatsu booth with its new 360-t (400-st) 980E-4 haul truck that included GE’s 360-t (400-st) electric wheel motor. This is just one example of how technology is connecting machines, operations and people around the world and how mining is moving forward."

Dec 1, 2016

By T. L. Barone, J. R. Patts, L. D. Patts, S. J. Janisko

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more effective and efficient use of rock dust. A prototype flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed inline between the face ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over three days at set distances from the fan exhaust to assess changes in float coal dust levels in the return due to operation of the scrubber. Mass-based measurements were collected on a per-cut basis and normalized on the basis of per ton mined by the continuous miner. The results show that average float coal dust levels measured under baseline conditions were reduced by more than 90 percent when operating the scrubber. IntroductionAirborne coal dust is a byproduct of coal production, and engineering controls exist to deal with both the respirable dust health hazard as well as the float dust explosion safety hazard. Float coal dust, smaller than 75 µm (0.003 in.) in size, can deposit throughout mine entries and propagate explosions that had been initially fueled by methane gas. The inertization of float coal dust with rock dust helps prevent a potential secondary float coal dust explosion, but a preferable course of action is to significantly reduce the hazard by removing float coal dust from the airstream before it has the opportunity to deposit on the mine’s surfaces.Since 1970, disasters due to explosions in underground coal mines have caused 201 deaths in the U.S. mining industry, including 29 deaths in a single mine explosion in 2010 (Wade, 2010; U.S. Mine Safety and Health Administration, 2015). The U.S. National Institute for Occupational Safety and Health (NIOSH) had initiated a fiveyear research project that aims to investigate methods and technologies to reduce the potential for secondary coal dust explosions by the purposeful capture and/or suppression of float coal dust prior to its deposition on the mine roof, rib and floor (NIOSH, 2013). The project aims to evaluate the efficiency of methods to reduce longwall and belt airway float dust in the general airstream as well as methods to capture it at or near the source. Prioritization is given to longwall sections given the amount of coal produced relative to continuous miner sections, but the research is open to technologies that may be adapted from one method of mining to another."

Dec 1, 2016

By Kenneth Deaton

"A packaged cooling system is being developed for refuge alternatives (RAs) that will meet U.S. Mine Safety and Health Administration (MSHA) qualification guidelines for deployment in coal mines. This system will allow full occupancy ratings of deployed refuge alternatives to be maintained by keeping the apparent temperature inside the RA from exceeding 35° C (95° F).Research investigations sponsored by the National Institute for Occupational Safety and Health (NIOSH) have shown that heat buildup caused by occupants in mobile RAs will result in apparent temperatures that exceed the 35° C (95°F) limit established in 30 CFR 7.504.Figure 1 shows the temperature rise in an inflatable RA having an occupancy rating of 23 people at an 27° C (81°F) mine air temperature. This plot shows the need for either heat mitigation or occupancy derating in warmer mines.The Refuge Alternative Environmental Control System (RAECS) will be designed to provide enough heat mitigation to eliminate occupancy derating due to heat buildup over the 96-hour refuge period.This article describes testing of a prototype cooling system that uses proven vapor compression technology powered by batteries to keep the RA interior below the 35° C (95° F) limit for a minimum of 96 hours. Testing of this prototype cooling system was conducted in December of 2015 and January of 2016 at the NIOSH test mine in Bruceton, PA. December testing was conducted at the prevailing mine ambient temperature — approximately 15.5° C (60° F). The January testing was done with the mine ambient temperature in the immediate vicinity of the RA artificially elevated to 29° C (85° F). Realistic heat gain from RA occupants was provided by human simulators developed by NIOSH. These simulators add sensible heat corresponding to human metabolic processes and latent heat generated by respiration and perspiration. Heat generated by CO2 scrubbers was also added. Results of cooling system performance using these simulated loads at the two ambient conditions are described. A comparison of the apparent temperature in the RA using two different control techniques is also presented. This work documents the ability of the cooling system to meet the established apparent temperature limit at the full occupancy rating of a six person RA. A new cooling system intended for use with existing RA deployments and having greater cooling capacity is currently in development and will be described.Expendable desiccant modules were also used to provide supplemental water vapor removal and their role in mitigating cooling load is addressed."

Dec 1, 2016

By Jorge Acosta Ale

"El presente texto señala la perspectiva de la producción peruana de cobre para la próxima década y su aporte económico en el Perú a través de un cuadro estadístico donde se observa un incremento de los pórfidos de Cuajone y Cerro verde en los años 70´, skarn de Tintaya en los 80´ y Antamina en el 2001. Así también se revisa el canon minero, regalías mineros y derechos de vigencia. "

Dec 1, 2016

By Amado Yataco

"El presente texto describe una aproximación sobre la producción de los ocho metales -en tanto determina el Producto Bruto Interno durante el período 2016 en el Perú. Los metales considerados son: cobre, oro, zinc, plata, molibdeno, plomo, hierro y estaño. Asimismo, se muestran cuadros gráficos de la producción de los años 2012 y 2015 para tener series de producción reales y las mejores estimadas del 2016 y 2017. Finalmente se presenta la evolución del PBI en Cerro Verde, Las Bambas y Antamina. "

Dec 1, 2016

By William Gleason

"Speakers and attendees of the 2016 Cutting Edge Conference could not be faulted for keeping one eye on the presentations taking place at the Hyatt Regency at LAX in Los Angeles, CA on Nov. 7 and 8 and another on the results of the historic election in the United States that took place on Nov 8. While there was certainly interest in the presidential campaign, there was also a great deal of interest in Measure M on the California ballot. Measure M, which passed easily, is a half-cent sales tax increase that will fund the most ambitious transit expansion in Los Angeles County history.In the coming years, the ballot measure will transform a traffic-choked region by funding the construction of nearly a dozen new rail lines with an estimated $120 billion raised in four decades. Among the projects that could come to fruition are a twin-rail tunnels project through the Sepulveda Pass and new connections in the city.During the update on West Coast projects, Bill Hansmire summed things up with a slide asking “How much work is there on the West Coast,” and his answer was “Billions.”From Seattle, WA south to Los Angeles, there is already a lot of work for tunneling and underground construction experts, and Measure M ensures that there will be plenty of work for decades to come.Currently, The Los Angeles County Metropolitan Transportation Authority (Metro) has three rail projects underway that were funded by Measure R in 2008 — the Regional Connector, the Purple Line subway extension and the Crenshaw/LAX Line that are designed to alleviate the traffic pressure with an eye to more solutions.Measure M is the fourth sales tax increase to fund transportation in L.A. County, bringing the base sales tax rate to 9.25 percent. In some cities, which already levy their own sales tax, the rate would be higher, The Los Angeles Times reported.About 35 percent of the revenue will fund major new transit projects, such as the subway under the Sepulveda Pass, extension of the Gold Line to Claremont, extension of the Crenshaw Line to West Hollywood and acceleration of the Purple Line Subway construction along Wilshire Boulevard to finish in 2024, 10 years earlier than scheduled.About 17 percent would fund a dozen highway improvement projects, such as widening parts of I-5 in the Antelope Valley and southeastern county, adding bus lanes to the Sepulveda Pass section of the 405 freeway and adding truck-only lanes to a section of the 710 freeway."

Dec 1, 2016

By Z Fu, E Topal, O Erten

"Mine waste rock management involving waste rock movement and placement, is a critical aspect in the planning of open pit mining operations, as the waste rock haulage cost can be the largest portion of the mine operating cost. The concept of sustainable development in the mining industry also encourages environmentally friendly waste dumps that have zero hazards to people and the surrounding environment. Therefore, a detailed waste management schedule must satisfy economic and environmental considerations. However, the available tools in the market cannot provide optimal waste dumping schedules to meet all these constraints. This paper introduces a user-friendly and automatic tool to optimise the waste dumping schedule, which minimises the haulage cost, and covers the encapsulation of reactive materials to minimise acid mine drainage problems. This tool has been developed by using a new mixed integer programming (MIP) mathematical model that considers both single-lift and multilift dumping scenarios. The application of the proposed tool on a data set collected from a gold mine shows that the multilift dumping scenario has provided a more flexible and economical waste dumping schedule than the single-lift scenario, and both scenarios satisfy environmental requirements.Citation:Fu, Z, Topal, E and Erten, O, 2016. A Modified Software Tool for Mine Waste Rock Dump Planning, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 229–242 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By D Kavanagh, C Michaud

"A continuous improvement initiative was identified at Kalgoorlie Consolidated Gold Mine’s (KCGM) Fimiston open pit with the goal of reducing bench turnover time and increasing shovel digability by improving fragmentation around previously mined-out stopes. In the past, a higher number of blasts than normal would be required to get through a single excavation area where stopes were present. This is due to the limited reach capability of the drilling fleet from safe ground into restricted areas requiring the drilling of the shot to be done in a staged manner. In addition, the holes that were able to be drilled in the area did not remain open long enough to be loaded with explosives as a result of the poor ground conditions surrounding the stopes.Over the last 18 months, KCGM has trialled drill additives to improve blasthole stability, as well as introducing a remote drill rig allowing holes to be drilled in areas previously inaccessible by manned drill rigs. This has resulted in improved penetration rates in bad ground conditions, improved drill hole stability, better shovel digability, and an overall reduction in bench turnover of at least ten days on the benchmarked 126 days average per bench. KCGM is now in the final stages of the improvement project with the installation of a drill monitoring system on the fleet to allow live data transfer back to the office for analysis, as well as providing improved accuracy on drill holes in restricted areas.Citation:Michaud, C and Kavanagh, D, 2016. Reducing Bench Turnover Time and Improving Shovel Digability, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 19–27 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By R Price, B H. Miller

"The rise of autonomous haul truck fleets may have been initially driven by the rapid escalation of the cost of equipment operators, but the actual improvements reported by the major iron ore miners far exceeds the simple reduction in workforce. Utilising cost models developed for feasibility studies and mining contract modelling, the limits of cost improvements due to simple labour reductions are compared to those achieved by the early autonomous fleet adopters and through traditional process improvement techniques such as fleet class upgrades or hot-seating of equipment. As autonomous fleet implementation matures, it is likely that the gains seen by current adopters will seem minor compared to the limits generally governed by the limit of equipment utilisation. This ultimate limit is explored through time utilisation models, which were also developed for use in feasibility studies and mining contract modelling.Citation:Miller, B H and Price, R, 2016. Autonomous Haul System Savings - It's Not about Less Truckies but Better Truckies!, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 2–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By J Darbritz

"This paper details the events leading up to a slope failure that occurred at Kalgoorlie Consolidated Gold Mines (KCGM) and the remediation method executed using rope access specialists.n January 2016, KCGM Fimiston Pit experienced a double bench wall failure where approximately 80 000 t of material fell from the wall that blocked access to a ramp and caused minor damage to equipment.The event was triggered by heavy rainfall and occurred along unfavourable eastward dipping structures that lead into weaker shale/porphyry bands, which in turn left more material on the face. A remediation plan was formulated that would allow for the continuation of open pit operations while a full geotechnical assessment of the failure area could be conducted. This was accomplished by means of rope access specialists who abseiled down the wall and blasted off the remaining overhang using a portable drill rig and prepackaged explosives.This paper provides a brief overview of the KCGM operations, how the instability was identified and monitored, details of the failure event, outcomes of the geotechnical assessment and details on the remediation work.Citation:Graf, C and Sullivan, R, 2016. The Journey to Steepening the Pit Slope Angle - Advancing the Effectiveness of Wall Control, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 104–114 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By R Thompson, J Miedecke, D Handel, E Tomicek, D Tulloch

"The Mine Haul Road Optimisation Alliance (HROA) is a unique Australian industry–academia collaboration that has been developed to support mine haul road operators. The alliance integrates industry, end-user service providers and academic research expertise in mine haul road design, construction and operation to identify, quantify, implement and monitor the various equipment, materials and road management strategies and solutions required to drive haulage productivity improvements.Initially, a broad overview of the university–industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis internationally. This insight places into context the opportunity that strategic collaborations present, to drive productivity and efficiency in mining, while also delivering innovative technology solutions.Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry collaborations can deliver a more robust and needs-driven solution to mine haul road design, performance and management, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service providers alike form the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and practical, implementable solutions.The paper concludes with examples of how the alliance collaborations work in practice to deliver focused mine haul road research outcomes, together with the mechanisms used to ensure industry needs are met through end-user driven research solutions for enhanced operational performance.Citation:Handel, D, Miedecke, J, Thompson, R, Tomicek, E and Tulloch, D, 2016. Driving Haulage Productivity Improvements through Industry–Academia Collaboration, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 243–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By A K. Ghosh, J Chung, E Topal, M Asad

"Many open pit (OP) mines with considerable vertical extent are approaching the end of their life-of-mine; some of them are seeking the opportunity to make the transition from OP to underground (UG) mining. The decision on the best location for transition from OP to UG mining should be addressed at the strategic mine planning stage. Conservatively, the transition to UG mining is considered near or after the exhaustion of the reserve within the ultimate pit.However, if UG is evident and exclusively viable from the inception, defining the best location for the transition through a conservative approach may not be an optimal option to explore. This clearly establishes the need for a mathematical model that aims to maximise the project value and considers OP and UG mining with crown pillar (CP) requirement simultaneously. Underground mine layout varies from one UG mining method to the other, and consequently the variation in the location of transition is eminent. Thus, focus on the selection of UG mining method must be a part of this analysisThis paper presents an implementation of an integer programming (IP) based mathematical model that evaluates the changes in mining layout and the project value under possible variation in the transition point from OP to UG mining for stoping and block caving methods. An IP problem is a mathematical optimisation or feasibility method in which some or all of the variables are restricted to be integers. The outcome of the implementation reflects that mining strategies with OP transition to stoping and block caving methods generated higher values than OP-only mining strategy. The case study not only demonstrates the difference in mining layout for both stoping method and block caving method, but also reflects that a joint consideration of OP mining, UG mining and CP placement helps to achieve maximum project value and resource utilisation.Citation:Darbritz, J, 2016. Remediation of Wall Failure at Kalgoorlie Consolidated Gold Mines' Golden Pike Cut-back 2016, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 96–103 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By B Reid

"Since the commencement of mining operations at the Cowal Gold Operations (CGO) in 2005, reverse circulation (RC) drilling has been the preferred method for grade control (GC) sample collection. This method was selected because it allowed:for multibench drilling (20 m hole depths for two benches of mining) to aid mine planning increased data density for comparison against the wide spaced ore reserve model angled drill holes to intersect perpendicular to the strike and dip of the shallow dipping mineralisation ability to take two metre sample intervals to enhance the understanding of the mineralisation’s short-scale variability and provide the ability to flitch mine.From June 2008 to December 2013, RC GC was performed using a UDR rotary cone splitter. The field duplicate data over the period displayed strong precision, with a correlation coefficient of 0.94 and an average relative per cent difference (RPD) of 21 per cent for gold. Up to 66.1 per cent of field duplicate data greater than 0.1 g/t fell within ±20 per cent RPD. This is within limits of industry best practice. The Mine to Mill reconciliations over the same period showed the estimated GC grade was 7.7 per cent lower than the calculated head grade (CHG).In December 2013, the Progradex sampling system (PGX) was introduced at CGO due to its advertised ability to capture 100 per cent of the drill cuttings for the complete sample interval, inclusive of fines. Analysis of field duplicate data indicates that since the introduction of the PGX, the sample precision has drifted. From January 2014 to February 2016, the correlation coefficient was 0.92 and up to 51.2 per cent of field duplicate data, greater than 0.1 g/t fell within the ±20 per cent RPD. Over the same 26 month period, the Mine to Mill reconciliation improved to one per cent lower than the CHG. Granulometric analysis of the RC samples collected from the PGX indicated the fines material(<212 µm) averaged up to 22 per cent of the samples mass and following assay determination, the fines material represented a weighted average of 31 per cent of the total gold content within the sample.This paper highlights the:importance of the complete capture of all drill cuttings during an RC drill programinfluence of fines material on the sample quality and accuracyimpact sampling of the fines material has on the Mine to Mill reconciliation performancechallenges experienced in commissioning a PGX system.Citation:Reid, B, 2016. A Fine Looking Sample - the Importance of Fines in Grade Control Sampling to Mine to Mill Reconciliation, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 28–38 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By W Zeng, D Walker, D Cai, E Baafi

"The efficiency of the truck-shovel haulage system is significantly influenced by the truck fleet size. A discrete event simulation model with 3D animation has been developed to estimate the productivity of a truck-shovel network system, shovel efficiency, truck cycle time, truck utilisation and the optimal fleet size. The simulation model considers the dynamic variability of traffic conditions and also the truck as an individual entity. The resulting truck cycle time was found to be realistic and thus providing a better tool for strategic mine planning.Citation:Zeng, W, Baafi, E, Walker, D and Cai, D, 2016. A 3D Discrete Event Simulation Model of a Truck-shovel Network System, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 265–273 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By D J. Robinson, L L. Kuhar

"Regardless of orebody value, at some stage, the pit will reach a depth where the reward for mining wider and/or deeper is not justified by the anticipated returns. ‘Last-blast’ strategies may help to some degree in recovering additional quantities of the resource but when a pit remains, there is often significant value left in the ground. In addition, in many cases, one or many good reasons may dictate why going underground and pursuing the orebody below the pit is also not justifiable. Whereas the company can hopefully move on to other more prospective parts of the orebody, the remaining options for the pit are usually very limited. Typically the pit is either held for potentially more favourable future pit expansion opportunities or it could be used for an alternative purpose, such as tailings or waste storage. This paper will present an alternative option that involves the direct extraction of values using in situ recovery (ISR) methods to recover additional value metals from the walls and/or floor of the pit. ISR involves circulating a fluid through the remaining orebody, solubilising the target metal and subsequently returning the solution to the surface for metal recovery. ISR is not the panacea to all but it has been employed selectively in the minerals industry for some time and the production of metals, such as uranium, rely heavily on this approach. ISR is not yet considered by many operators as an approach to compete with open pit or underground mining, largely because of the perceived limitations of this approach and the perceptions of risk. Rapid recent development of tools and enabling technologies relevant to ISR have made us reconsider the most economic approach to extracting many other metals from known mineral systems, even those currently listed as subeconomic. We suggest that ISR has the potential to make mine operators rethink the end of the pit life and adopt an innovative ISR approach to work toward a more complete recovery of value metals from existing pits.Citation:Kuhar, L L and Robinson, D J, 2016. In-pit In Situ Recovery - a New Approach That May Allow for Increased Value Extraction before Pit Closure, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 275–283 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By William Gleason

"There are few people more qualified to speak of the tumultuous times in the global mining industry during the past four years than Newmont Mining Corp. president and chief executive officer Gary Goldberg.Goldberg stepped into his current position in 2012, just before MINExpo 2012. Gold prices had hit record highs not long before that ($54.15/g or $1,856.40/oz on Sept. 8, 2011), expansions were happening around the world and the gold mining sector was still living in the glow of one of its longest upswings in history.That all changed between April 8 and April 15, 2013 when the price of gold dropped by nearly $200/oz ($46.27/g or $1,586.20/oz on April 8 to $40.45/g or $1,386.80/oz on April 15), putting an end to the decade-long mining boom and forcing mining companies like Newmont to re-evaluateeverything.Three years later, with the gold sector recovering, Newmont Mining is not only surviving but is thriving with a pair of mines coming online, Long Canyon in Nevada and Merian in Suriname. On Oct. 1, the Merian Mine went into production on time and more than $150 million under the initial development capital budget.Goldberg, who was one of the featured speakers at the opening session of MINExpo International 2016 on Sept. 26, also spoke with Mining Engineering about the previous four years and the future of the industry.“Mining goes through cycles all the time and gold is no different,” Goldberg told Mining Engineering when asked about surviving the downturn since 2012. “I thought it was important that we take a good methodical and steady approach across the business to determine what was the right thing to do and to set the business up to improve performance. Anyone can cut costs for the short term, but we set out to do it in a sustainable and reliable way. We created a program we call Full Potential to look for sustainable ways to reduce costs and improve productivity. That program has taken more than a billion dollars out of our costs since we implemented it 2013 and that shows up in our results. Our all in sustaining costs are down 28 percent and our productivity is up 39 percent.”During the downturn, Newmont restructured its business model, sold off some assets and created a leaner, more nimble operation. It has paid off with the addition of two new mines and the acquisition of another, the Cripple Creek & Victor Mine in Cripple Creek, CO.“The gold industry had not seen a downturn in 12 years. We had half a generation that had not experienced a downturn, so helping them through that in an organized way and keeping a view toward the long term throughout the downturn was important. We were one of the few companies that continued to invest in assets,” he said."

Nov 1, 2016

By R. Adsero

"A high altitude review of the state of the mining industry provided by a study of multifactor productivity shows a continuation of lower output year on year for the capital and labor inputs applied. The story is sadly similar for both U.S. mining and the Australian mining sector. In fact, according to PwC analysts, the world’s mining equipment productivity has declined 20 percent during the past seven years (Lumley, 2014). Although the reasons for the continuing decline in mining productivity are varied, the need for improvement is clear.The world’s mining industry fleet of more than 400 large draglines moves billions of tons of overburden and ore (phosphate, limestone, etc.) annually. This discussion will review a few of the tools available for improved productivity in dragline operations.Benchmarking equipment performance exposes the possibilitiesIn the September 2013 Mining Engineering cover story Graham Lumley and R. Adsero suggested that analyzing best practice equipment performance from an industrywide database for specific equipment performance improvement goals would be beneficial (Adsero, 2013). Benchmarking equipment performance by normalizing differences and then comparing specific measures of performance will provide a road map to improvement for those following the leaders. For those already performing at best practice levels, a benchmark confirms and bolsters what has already been achieved. As described in the SME February 2014 paper by this author, best practice is the average of the top 10 percent in annual output. Filling performance gaps identified by a comparison to best practice by investigating the details of the why and taking action to change, makes all the difference. This is true for all major mining equipment. Given the large gap between average performance and best practice performance most mining operations can benefit. Best practice performance provides a view of what is possible to the 90 percent majority of mining operations that are performing below the top 10 percent.For dragline mining operations, identifying specific characteristics and practices of leading dragline performance will provide a reference for comparison."

Nov 1, 2016

By W. R. Reed, J. P. Rider

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) recently developed a series of models using computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a mediumsized surface blasthole drill shroud with a dry dust collector system. Previously run experiments conducted in NIOSH’s full-scale drill shroud laboratory were used to validate the models. The setup values in the CFD models were calculated from experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for several test scenarios, including 0.14 m3/s (300 cfm) and 0.24 m3/s (500 cfm) bailing airflow with 2:1, 3:1 and 4:1 dust collector-tobailing airflow ratios. For the 2:1 and 3:1 ratios, the calculated dust concentrations from the CFD models were within the 95 percent confidence intervals of the experimental data. This paper describes the methodology used to develop the CFD models, to calculate the model input and to validate the models based on the experimental data. Problem regions were identified and revealed by the study. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. IntroductionIn surface mines, production drilling is an essential process in blasting to fracture the hard rock overburden for removal. During the process, considerable amounts of respirable dust are produced. Past sampling at the shroud area of blasthole drills had documented time-weighted-average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 (Organiscak and Page, 1995) and 1.04 to 52.30 mg/m3 (Listak and Reed, 2007). These high dust concentrations, which may contain silica, can lead to respirable dust overexposures for the miners working nearby. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal.Two basic methods are used to control drilling dust: a wet suppression system or a dry collection system (Cecala et al., 2012). Dry drilling techniques using a dust collection system are preferred in rural mining locations where a constant water supply is not available, and in the case of rotary drilling where water is associated with accelerated bit wear due to bearing degradation and hydrogen embrittlement. In addition, dry drilling eliminates freezing-related issues with water in colder climates. Dry dust collectors are highly effective at removing dust, especially the finer material, as long as they are properly operated and maintained (Listak and Reed, 2007; Organiscak and Page, 2005)."

Nov 1, 2016