Search Documents

By A. D. Yell

"Recovery of water is always a major factor in the Beneficiation process. As Preparation Plants become larger the recovery of water for reuse, is a critical cost consideration. Tema Isenmann Inc in conjunction with our sister Company Multotec Manufacturing, has over the years, developed numerous different Screen Panels, Sieve Bends and Static Screens for dewatering. This paper will focus on a new innovation, the TeePee™ Panel which has double the open area of conventional Screen Panels. This results in efficient dewatering (reduced filter cake moistures) which allows for the use of smaller Vibrating Screens or increased capacity on existing Vibrating Screens. A major factor in the efficiency of any Screen Panel, including TeePee™ Panels, is the performance of the Vibrating Screen. If the Vibrating Screen does not have the required gravitational force or screen area to drain it will not dewater efficiently. Therefore a holistic approach has to be taken where the Vibrating Screen needs to operate at an optimal level, in conjunction with the correct Screen Panels, to achieve efficient dewatering. Key performance areas for Vibrating Screens are therefore detailed in this paper with an emphasis on important dewatering criteria. Case studies of different dewatering applications are included, where the use of TeePee™ Panels, has shown a marked improvement over conventional flat Screen Panels in reduction of filter cake moisture content.INTRODUCTION Dewatering can be done in a number of different ways and is largely dependent on the ore type, the particle size distribution and to what extent one needs to dewater will determine the method used. There are a number of different dewatering methods that can be used for particles above 200 micron, including Screen Bowl Centrifuges, Filter Presses, Static Screens, Static Sieve Bends and Vibrating Screens. This paper will focus primarily on Vibrating Dewatering Screens showing improved drainage and a reduction in the filter cake moisture content. KEY PERFORMANCE CRITERIAL FOR VIBRATING DEWATERING SCREENS For clarification the critical key performance criteria for Vibrating Dewatering Screens are set out in this paper. Dewatering Screens Vibrating Dewatering Screens are normally linear motion, either horizontal or inclined at 5 to 7° upwards with a vertical or back sloped plate at 45° to the rest of the screen deck. The back plate will often have screen panels in them to increase the dewatering capability, as shown in Figure 2 below."

Jan 1, 2017

"How Wall Street Darling Molycorp Undermined the U.S. Economy, Degraded our National Security and Distorted the Global Economic Balance and How These Falsehoods Continue to be Promoted Even Today INTRODUCTION & SUMMARY In 2007 the Molycorp Mountain Pass rare earth mine was resurrected from its desert-grave in California by its then-owner Chevron Mining. Responding to elevated rare earth prices Chevron began processing on-site rare earth concentrates left over from past mining operations that were terminated in 1998i. Chinese demand had sparked what was being described as a commodities super-cycleii. Commodity prices were on the move. Wall Street smelled opportunity. In 2008 Goldman Sachs, Pegasus Partners, Resource Capital Funds, Traxys North America LLC and Carint Group LLC acquired the mining assets from Chevron. In an environment of ever-declining ethical standards and regulatory consequences the private capital group and their investment bankers would bring Molycorp to market. Molycorp, with its high powered investment banking team of Morgan Stanley and J.P. Morganiii, easily dominated the contest. Molycorp promoted itself, largely based on its past operating history and proven reserves, as the best company to challenge China’s monopoly control over the production of rare earths: a group of elements critical to most advanced technologies and U.S. defense systemsiv. Most of Wall Street’s hottest investment sectors were dependent on these materials: alternative energy, green technologies, computing, personal communications, advanced electronics and defense systems. By late 2010 there were dozens of prospective rare earth start-up ‘mining companies’ seeking capital. Eventually the number of prospective rare earth mining companies seeking capital exceeded 400, despite the reality that supply requirements of this market were disproportionally small when compared to other natural resource sectorsv. In the world of finance ‘smart money’ picks the winners. Consequently just twovi projects attracted nearly all of the capital (Molycorp and Lynas). Wall street picked Molycorpvii. This paper will primarily focus on Molycorp. By early 2010 the words “Molycorp” and “Rare Earths” electrified many people in the mining industry, most non-Chinese manufacturing technology companies, U.S. & allied defense contractors, technocrats in the U.S. national security community and eager investors across most of the world’s stock markets. It was the hottest story of the yearviii. The financial, technology and defense press coverage verged on euphoric: heaping fuel on fuel until the highly combustible Molycorp-pyre cast a long shadow over all of its rivalsix. When the IPO match was lit the spectacular flaming pyre sucked all of the oxygen out of the rare earth spacex. Molycorp was ranked the most lucrative IPO of 2010, resulting in record breaking profits to its private investors and massive returns for its early stock holding investors."

Jan 1, 2017

By William G. Pariseau, Mark K. Larson, Douglas R. Tesarik, Heather E. Lawson

"This contribution describes development and application of a user-friendly finite element program, UT3PC, to address three important problems in underground coal mine design: (1) safety of main entries, (2) barrier pillar size needed for entry protection, and (3) safety of bleeder entries during the advance of an adjacent longwall panel. While the finite element method is by far the most popular engineering design tool of the digital age, widespread use by the mining community has been impeded by the relatively high cost of and the need for lengthy specialized training in numerical methods. Implementation of UT3PC overcomes these impediments in three easy steps: First, a material properties file is prepared for the considered site. Next, mesh generation is automatic through an interactive process. A third and last step is simply execution of the program. Examples using data from several western coal mines illustrate the ease of using the application for analysis of main entries, barrier pillars, and bleeder entry safety.INTRODUCTIONRational design of safe underground entries and crosscuts, barrier pillars, and bleeder entries begins with a site-specific analysis of stress. An analysis of stress identifies the critical regions of high-stress concentration where yielding is likely and additional or more focused ground control measures are needed. This analysis also identifies regions where stress concentration is low, and risk mitigation is less urgent. Displacements induced by mining, including roof sag, floor heave, and pillar squeeze, are also of importance to stability. The popular finite element method is well-suited for such analysis and has been in use for studying coal mine engineering problems since the late 1960s (Dahl, 1969). The method has been taught in undergraduate engineering curricula for many years and offers an alternative to existing design procedures based mostly on rules of thumb, empirical methods based on mine data, and predigital-age concepts of strata mechanics. However, despite the versatility of the finite element method, usage has been limited, mainly because of the cost of the software and the required training in numerical methods.The program UT3PC (Pariseau, 2017) has evolved from early two-dimensional versions in the era of mainframe computers. These early versions were still quite limited using only a few hundred elements that required overnight turnaround times. Recent versions of UT3PC are convenient and efficient desktop programs that use several million elements. With the advent of personal computers in the mid-1980s and subsequent increase in computer speed, expanded memory, and lower costs, applications for mining increased in three-way cooperative projects among industry, the former U.S. Bureau of Mines, and academia. The Spokane Research Center of the U.S. Bureau of Mines, in cooperation with the University of Utah, developed a two-dimensional desktop finite element program, UT2PC, available to the mining community in 1991. This was a short course offered at the 1991 SME Annual Meeting in Denver, CO."

Jan 1, 2017

By Esterhuizen S. Gabriel, Su W. H. Daniel, Tulu B. Ihsan, Klemetti M. Ted, Mohammed M. Khaled, Gearhart F. Dave

"A numerical-model-based approach was recently developed for estimating the changes in both the horizontal and vertical loading conditions induced by an approaching longwall face. In this approach, a systematic procedure is used to estimate the model inputs. Shearing along the bedding planes is modeled with ubiquitous joint elements and interface elements. Coal is modeled with a newly developed coal mass model. The response of the gob is calibrated with back analysis of subsidence data and the results of previously published laboratory tests on rock fragments. The model results have been verified with the subsidence and stress data recently collected from a longwall mine in the eastern United States. INTRODUCTION In 2015, there were 40 longwall mines operating in the United States, each producing an average of 4.5 million tons of coal per year, and they supplied 60% of the U.S. underground coal production. This represents a substantial increase from 50% three years earlier (Sears, Tulu, and Esterhuizen, 2017). During this period, reportable roof fall rates in U.S. longwall mines also increased. Large roof falls that can block the gateroads are not only a ground-fall hazard, they can disrupt the ventilation system, block the escapeways, and increase the potential for elevated methane levels in the gob. To address these hazards, the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) is conducting research to improve the design of ground control systems in longwall gateroads. Gateroad stability is primarily determined by the longwall pillar design. Generally, the required dimensions of the pillars around a longwall panel are determined first, which then dictates the location of the gate entries relative to the mined panel. The Analysis of Longwall Pillar Stability (ALPS) method is the most accepted gateroad pillar design procedure in the United States (Mark, 1992). The ALPS method accounts for local roof geology in the gateroad stability assessment by including the Coal Mine Roof Rating as an input parameter (Mark, 1992). The key assumption in the ALPS method is that unstable pillars result in unstable gate entries. However, experience provides examples of mines where pillar stability and gateroad stability are only loosely correlated (Su, Draskovich, and Thomas, 2003)."

Jan 1, 2017

By P. T. Bissert, L. Yan, J. R. Srednicki, J. A. Yonkey

"Refuge alternatives (RAs) are required in underground coal mines to support life post-disaster. RAs are mandated by MSHA to maintain an apparent temperature (AT) at or below 95°F (35°C) while providing a safe and livable shelter for a minimum of 96 hours. Because strata composition and mine temperatures will affect the final AT within an occupied RA, NIOSH researchers have collaborated with five underground coal mines across the US to characterize the effects of geographic location and seasonal temperature fluctuations on mine air temperature, relative humidity, and mine strata temperatures. The data collected indicates that some mines will experience greater temperature fluctuations than others, based on geographic location. The mine which demonstrated the greatest temperature differential over the course of the year resulted in a mine air temperature that ranged from 53.4°F (11.9°C) to 84.2°F (29.0°C) and a rib surface temperature that ranged from 55.4°F (13.0°C) to 82.8°F (28.2°C). This data suggests that the location and seasonal peak temperature can significantly affect the mine strata temperature, which could lead to a fully occupied RA exceeding the 95°F (35°C) AT limit over the course of 96 hours. The data reported in this paper could be used to examine the heat buildup inside an RA for actual mine conditions. Thermal simulations could be implemented to evaluate maximum occupancy ratings based on actual mine temperatures and strata compositions. INTRODUCTION In the event of a mine disaster, miners’ primary focus is to escape. Should their attempt be futile, they can enter a refuge alternative (RA) to await rescue. In 2008, the Mine Safety and Health Administration (MSHA) mandated that underground coal mines implement RAs within 1,000 ft (304.8 m) of the working face and spaced within one-hour travel distances in outby areas where persons work such that persons in outby areas are never more than than a 30-minute travel distance from an RA or safe exit. These RAs are required to provide a safe and habitable shelter for a minimum of 96 hours and to prevent the apparent temperature (AT) from exceeding 95°F (35°C) [1]. There is concern throughout the industry that in some cases the internal ambient of occupied RAs may exceed the 95°F (35°C) AT limit due to the potentially hot mine atmosphere as well as the metabolic heat generated by RA occupants and the carbon dioxide scrubbing system. The National Institute for Occupational Safety and Health (NIOSH) has conducted tests in its Safety Research Coal Mine (SRCM) and its Experimental Mine (EM) to investigate heat buildup in RAs. It was found that the number of occupants in an RA may need to be reduced based on the ambient mine temperature, which varies from mine to mine [2]. Further testing and analyses were completed to evaluate the mechanisms (conduction, convection, radiation) by which heat is transferred from an RA to the mine surroundings. Additionally, the effects of varying mine strata compositions on the heat buildup inside an RA were studied [3]. The mine strata temperatures will increase due to heat transfer from within an RA. Depending on the mine strata composition, some mines may be more thermally conductive than others. For example, sandstone is much more conductive than shale or coal (i.e. it disippates heat at a quicker rate). All things being equal, the air temperature inside of an RA after 96 hours will be higher for a mine with strata that has low thermal conductivity compared to a mine with high thermal conductivity."

Jan 1, 2017

By John C. Niedzielski, A. Frances Ackerman

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site’s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The fullscale field test played a significant role in the design of the project’s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

Jan 1, 2017

By Damir Dedic, Wörle. Patrick

"Soil properties within a construction project area are analyzed during the planning phase. However, it is only possible to achieve selective soil exploration, even in the case of very extensive investigatory programs, which results in a certain soil risk and uncertainties for planning and execution.Therefore, the application of monitoring systems is becoming increasingly important in the field of geotechnics. The application of suitable monitoring systems for these particular purposes provides considerable knowledge relating to the load bearing behavior of the soil and the ground anchor. Applications that present major challenges to measuring anchor forces include back-anchorages of long-lasting and very deep construction pits, construction pits in urban areas, slope and embankment supports for track and vehicular routes, port and lock structures, and uplift control. Apart from overseeing individual construction stages, monitoring systems analyze the interaction between the soil and structure throughout the latter’s entire life cycle and safeguard the functional capability of the applied system components. Geotechnical construction projects can be adapted, optimized and carried out with enhanced safety from the information obtained.Conventional Monitoring SystemsThere are numerous approaches for determining anchor forces of bar or strand anchors. Lift-off tests and measurements with load cells are the most common methods.Lift-off Test: Lift-off tests provide a possibility to monitor the prevailing force in strand or bar anchors. The entire anchor head structure is lifted using the appropriate equipment. The steel tendon is prolonged, or in the case of strand anchors, a screw-on cap holds the wedge carrier so that a tensioning jack can be mounted above it. Then, the tendon is prestressed until the lower anchor nut (bar) or wedge carrier (strand) is lifted off from the anchor plate. The intersection of the two straight lines in the figure represents the force at which the anchor nut or the wedge carrier lifts off from the anchor plate. Thus, the intersection displays the actual load of the anchor. This form of anchor force control gives conclusive results, but at the same time requires extensive accessories and extra personnel to execute the test. For this test, a sufficient bar overhang must be available, the wedge plate must possess an external thread, or there must be a strand overhang of at least 24 in (60 cm). Furthermore, the anchor head must be freely accessible and in a position to be reached with the necessary equipment."

Jan 1, 2017

By P. Lind, A. Gagnon

"Goldcorp has embarked upon an ambitious, industry-leading, multi-year water use reduction effort. This is a proactive, voluntary effort that reflects our commitment to truly sustainable mining. This effort will focus on increasing water re-use and recycling, and reducing water inputs ultimately towards zero. All of our operating mines are expected to contribute to this effort and are currently in the process of developing plans to meet short and long term objectives. One of the largest needle movers to increase water re-use and recycling is in the area of tailings management. Within five to ten years at Goldcorp, it is envisioned that the need for wet tailings dams will be eliminated and that all new tailings facilities will consist of only filtered or dewatered tailings. Filtered tailings is developing into a mature technology with wide application in mine waste management. This paper describes a conceptual level evaluation on the transition from a slurry to a filtered tailings operation at the Cerro Negro mine in southern Argentina. Key benefits and challenges are highlighted.INTRODUCTION Goldcorp’s Cerro Negro operation is located in the Santa Cruz province in the Patagonian region of Argentina. Cerro Negro has been in operation since 2014 and commercial production was achieved on January 1, 2015. The processing capacity of the plant is 4,000 tonnes of ore per day and in 2016 produced 363,000 ounces of gold and 3.1 million ounces of silver (Goldcorp Inc., 2017). As the mine is located in a semi-arid area, it is important to evaluate technologies that could reduce freshwater consumption and maximize water re-use and recycle rates. The current tailings operation at Cerro Negro incorporates pumping of tailings slurry into a conventionally lined Tailings Storage Facility (TSF). Water is reclaimed from the tailings supernatant pond to the process plant via pumps, however, water losses occur due to evaporation and solution retention within the slurry tailings voids. Converting to a filtered or dewatered tailings operation would allow for increased water recovery prior to tailings disposal, and decreased water losses from evaporation and from retention in the tailings solids void space. This paper describes a conceptual level evaluation on the transition to filtered or dewatered tailings with the primary objective of moving closer Towards Zero Water."

Jan 1, 2017

By J. Zhai, Z. Yin

"The electrokinetic and flotation behaviors of ilmenite using lead ions as the activator and sodium oleate as the collector were studied. The results of microflotation show that the flotability of ilmenite can be improved by lead ions obviously. The isoelectric point of ilmenite increases from 5.32 to 7.7 after the addition of lead ions because of the adsorption of Pb2+ and Pb(OH)+. The results of zeta potential measurements and the collector adsorption density calculation show that the adsorption of sodium oleate on the ilmenite surface via chemisorptions in addition to electrostatic interactions. Besides, the adsorption density calculation results show that as the addition of lead ions as the activator, the adsorption amounts of collector are greater than those without activation which is in aggrement with the flotation behaviors. INTRODUCTION Ilmenite, as an oxide mineral of formula FeTiO3, is usually used as the main resource of the extraction of titanium (Bulatovic and Wyslouzil, 1999). There are many researches showing that the conventional methods, such as gravity separation, magnetic separation and flotation, do not work efficiently as expected (Mehdilo et al., 2015; Zhu et al., 2011). Nowadays, to produce ilmenite concentration feasibly and efficiently, these separation methods above are combined for a reason that the raw ilmenite ores are characteristic of poor, fine and complicated. Moreover, surface modification, such as surface dissolution method, microwave irradiation and oxidation roasting, is applied to improve the flotability of ilmenite currently (Welham and Llewellyn, 1998; Zhang and Ostrovski, 2002). Generally, fatty acid salts are used as the collector for the flotation of oxide minerals and sodium oleate is usually used as the collector for the flotation of imenite ores (Fuerstenau and Pradip, 2005). The mechanism, such as individual ion electrostatic adsorption, chemical adsorption, ion–molecule dimeric complex adsorption, and the coadsorption of ion and molecule, have not been discussed systematically using sodium oleate as the collector in the flotation of ilmenite (Somasundaran, 1983). Under the activation circumstance using the lead ion as the activator and sodium oleate as the collector, the interaction mechanism seems to be still unclear. In the present study, the interaction mechanism between ilmenite and sodium oleate using lead ion as the activator are studied by microflotation, zeta potential measurements and adsorption density calculation. EXPERIMENTAL Materials and reagents Pure ilmenite minerals were obtained from Panzhihua, Sichuan province, China. The minerals were ground in a porcelain mill with an agate ball. Following that, the prosucts were sieved, and the samples of -0.074+0.038 mm size fraction were used for the microflotation experiments. The results of XRF show that the content of titanium element is 30.58%, showing that the purity of ilmenite is above 90%. On the basis of the results of XRF, it is determined that the purity of ilmenite is very high and meets the needs of microflotation"

Jan 1, 2017

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid Deep Mixing (DM) shoring system was recently constructed for a high-rise development in downtown Vancouver, British Columbia, Canada for the temporary support of a five-level basement excavation. The site is bounded by an existing bridge off-ramp structure along its longest side and by city streets on the other two sides, which formed a truncated triangle in plan. A conventional secant pile wall was installed along the longest side, about 380 ft (116 m) in length, of the site. Hybrid shoring walls (HSW) 1 and 2 were installed along two shorter sides with each being 235 to 246 ft (72 to 75 m) long. HSW 3 completed the excavation support system along the shortest side with a length of about 55 ft (17 m). Cutter soil mixing (CSM) was proposed by the excavation and shoring design-build team in lieu of conventional secant piling. CSM was the preferred method to construct the infill panels between soldier piles because of the speed at which the shoring system could be constructed in the variable fill, peat, wood waste and overburden. Design ConsiderationsTo minimize the impact on buried utilities along the outside perimeter of the excavation, the temporary shoring was designed to limit the lateral displacements to less than 0.8 in (20 mm). Factors taken into consideration for shoring design included the lateral earth pressures from the fill and native soils, groundwater pressures, temporary construction loads (e.g., crane or heavy plant/equipment), and permanent structural requirements. The subsurface conditions at this site typically consisted of fill (cohesive and granular), overlying peat and/or wood waste, overlying clayey silt to sandy silt, overlying weathered to dense to very dense clayey silt till to sandy silt till with silt layers. Localized, perched groundwater was observed within the fill, peat, wood waste and sandy silt layers above the dense till."

Jan 1, 2017

By Renzo D. Verastegui, Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high-rise towers in New York City. The 52-story condominium building is located on a 60 ft by 100 ft lot (18.3 m by 30.5 m) on East 60th Street between Park Avenue and Madison Avenue. The geographically complex site is bounded by two fragile five-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City Transit (NYCT) subway tunnel on the south. To add to this complexity, the ambitious development required an excavation between 70 and 80 ft (21.3 and 24.4 m) deep, mostly below groundwater level in highly-permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 ft (7.3 m) over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This article describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.Site GeologyThe 1865 Viele Map provides the site topographic conditions prior to development in the area, and indicates that the site was at the eastern edge of a historic marshland, which was approximately west of Park Avenue and north of 58th Street. A historic stream, which ran alongside the eastern edge of the site, was part of a larger stream network that traversed the surrounding area. This stream network is also visible in the 1865 Viele map. In addition, the bedrock beneath the site lies in a highly weathered zone due to a couple of ancient faulted zones that transect the site. These indicate that a zone of highly weathered rock is expected."

Jan 1, 2017

By J. O. Marsden, M. M. Botz

"Heap leaching is responsible for approximately 21 percent — 3.9 million metric tonnes — of copper production and 9 percent — 270 metric tonnes or 8.7 million ounces — of gold production worldwide. Given metal price assumptions of $2.25/lb for copper and $1,250/oz for gold, these portions of global production generate revenues of $19 billion and $11 billion, respectively. For heap leaching operations, small changes in metal extraction efficiency drive substantial changes in operating cash flow margins and affect project viability. Variances in actual metal production from budgetary forecast estimates can mean the difference between success (value creation) and failure (value destruction) for a heap leach project. Despite the importance of heap leaching for copper, gold and silver production worldwide, there are no clear standards or guidelines for developing heap leach metal production forecasts. There is considerable variation among copper and gold producers that apply heap leaching technology as to how such modeling and forecasting is applied at the operational level. There are a variety of different modeling approaches that can be utilized for this purpose. However, these vary in cost, complexity, time to implement, accuracy and credibility. This paper explores the options available for heap leach modeling, discusses the advantages and disadvantages of each approach, and provides guidelines/recommendations for an effective approach to modeling metal production at existing or planned heap leach operations. The paper also provides expected ranges of variation between actual and modeled production.Introduction and backgroundHeap leaching is fundamentally different from other methods used in the processing and extraction of gold, silver, and copper and other base metals. Considered globally, the technique represents a relatively modest portion of production compared with the primary technologies applied for copper and gold recovery. Approximately 21 percent of copper production is attributable to heap leaching techniques, as opposed to 79 percent by conventional crushing, milling, flotation, smelting and refining. For gold, about 9 percent of global production is obtained from heap leaching, compared with over 90 percent by various combinations of crushing, milling, gravity concentration, flotation and/or agitated cyanide leaching processes or, in the case of placer deposits, by direct gravity concentration and/or amalgamation. In cases where heap leaching is the primary source of metal production, the ability to accurately forecast metal production may be the difference between commercial success and failure for a project or operation. Heap leaching — of crushed or run-of-mine ore — is also commonly applied as a secondary process to treat lower-grade ores from a given deposit, such as at Chuquicamata in Chile, Cerro Verde in Peru and Bagdad in Arizona for copper extraction and at Twin Creeks and Carlin, both in Nevada, for gold. In such cases, heap leaching provides incremental revenue to supplement the primary process. Variances between actual and forecast metal production from heap leaching as a secondary process are typically tolerated and absorbed within the overall site metallurgical balance. In either case, accurate production modeling and forecasting creates significant value for heap leaching projects, is essential for managing production expectations — timing and volumes — and is likely to be a critical success factor for most heap leach projects."

Jan 1, 2017

By K. L. Boyd

"Can the ever-increasing tonnages of ore and waste being mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each of the four stages of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in the material handling flowsheet from the mine to the mill, maximizing operating hours per year. INTRODUCTION Are larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications are now available. The rock size reduction process from the mine to the selected milling process facility has not changed since man first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages: • Stage 1: Mining (rock breakage and fragmentation) • Stage 2: Pre-screening (scalping) • Stage 3: Primary crushing • Stage 4: Fine crushing (secondary, tertiary and quaternary) Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments are the key stakeholders in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit. This paper focuses on the four stages of a rock size reduction circuit from the mine to the mill, equipment selection, various ore and waste handling flowsheets, and improvements in crusher station design, all with the purpose of maximizing availability and plant utilization percentages. What is a large tonnage? From 1907 to 1914, the American Panama Canal excavated 300 million tonnes of material in 7 years (History of the Panama Canal, Wikipedia). Today’s large mining operations can move the same material in 10 months, using large crushers or multiple crushers for ore processing and large crushers and a mixture of truck haulage and conveyors for handling the large waste tonnages. Some examples include:"

Jan 1, 2017

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By J. F. Burr, D. Snyder, W. Calder

"INTRODUCTION “Explosion protection” refers to techniques used to minimize the potential for electrical and electronic equipment to create an ignition while operating in a hazardous location (HAZLOC). In particular, U.S. coal mines are required to use equipment in certain areas of the mine that has been approved by the Mine Safety and Health Administration (MSHA) for use in a methane and coal dust environment to limit the risk of the equipment creating an ignition-capable spark or a thermal energy ignition. In general, MSHA’s regulations for explosion protection recognize two techniques: the use of explosion-proof enclosures (XP boxes) and 2-fault intrinsic safety for electrical and electronic equipment. For 2-fault intrinsically safe (IS) equipment, the U.S. mining industry requirements are unique in that the equipment is certified by MSHA. The criteria MSHA uses to evaluate equipment for intrinsic safety, as required by Title 30 of the Code of Federal Regulations (30 CFR) [30 CFR, Sections18.20(b), 18.68(a)(1), 19.1(b), 20.1(c)(2), 22.6, 23.6, and 27.20(a)], is published in a document referred to as ACRI2001 (1). Outside of U.S. underground mining, many industries and countries accept equipment that is designed to a consensus-based international standard (ANSI/ISA 60079-11 is the U.S. version). The purpose of this study is to provide an overall assessment of the ANSI/ISA 60079-11 standard on 2-fault intrinsic safety and the MSHA ACRI2001 acceptance criteria, and determine if the ANSI/ISA document can be an alternative to ACRI2001 while maintaining an equivalent or better level of safety for miners. There are many drivers for this study. First, immediately after the 2006 MINER Act (2) was passed, there was a perception in the industry that the unique MSHA requirements were contributing to delays or restricting the availability of equipment to meet the requirements of the Act. Additionally, the MINER Act required that mine operators submit an accident response plan for MSHA approval, to be reviewed every six months. MSHA is required to determine if these plans reflect the most recent credible scientific research and make use of currently commercially available technology. There is a concern, as expressed in a recent National Academy of Science (NAS) study (3), that the unique requirements for U.S. mining may be limiting the technologies available to coal miners and technology options for mine operators. Accordingly, the study recommended that the National Institute for Occupational Safety and Health (NIOSH) and MSHA re-examine their technology approval and certification processes to ensure they are not deterring innovation, and explore opportunities to cooperate with other international approval organizations to harmonize U.S. and international standards without compromising safety. Lastly, the National Technology Transfer Act (NTTA) and the accompanying Office of Management and Budget’s OMB-119 circular mandate the use of consensus-based standards by federal agencies. However, for U.S. mining operations, MSHA cannot accept such standards unless a determination is made that such standards provide an equivalent level of protection for the miner, per the requirements of the 1977 Mine Act, the 2006 MINER Act, and 30 CFR Part 18 regulations."

Jan 1, 2017

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

By Andrew Moran, William H. Walton, Matthew D. Emrick, Mary C. Nodine

"A rapidly growing company in the northern US needed a large auditorium built into a dolomite bedrock hillside. The structure required an 80-foot-deep earth retention system independent of the auditorium foundation and superstructure. Allowable wall movements were limited to less than two inches. A 60-foot-tall permanent shotcreted soil and rock nail wall was designed for excavation support. The soil and rock nail wall utilized both active (post-tensioned) and passive nails, with capacities and installation angles optimized to address varying soil and rock conditions and to support heavy surcharges. The wall was configured with three two-foot-wide benches to facilitate controlled blasting and removal of more than two million cubic yards of soil, limestone and dolomite bedrock, and featured a permanent cast-in-place concrete face and a robust waterproofing and drainage system. A 20-foot-high reinforced concrete retaining wall was required at the top of the soil and rock nail wall to raise grades, resulting in a large surcharge.Design of the soil and rock nail wall was initiated less than three months before the start of construction, requiring expedited geotechnical explorations, analyses, design, and construction that would occur simultaneously. Design changes were made to address the discovery of a weak clay residuum seam at depth running along the base of the excavation, as well as significant changes to the building footprint made after the start of construction. Extensive performance monitoring was conducted during construction to measure vibrations and movements.Introduction and Project BackgroundA fast-growing company in the northern United States had a need for 600,000 square foot, 11,000 seat auditorium as part of its campus expansion. The auditorium was built underground, into a hillside to preserve the views of rolling terrain and farmland beyond. It featured a green roof and rockwork facing that mimicked regional geologic formations. The sixstory building required up to 80 feet of earth retention, including 60 feet of excavation beneath existing grades.As concepts for the project evolved, it became apparent that due to the geologic conditions, space limitations on site and the depth of cut required, a standard counterfort wall system would not be feasible. With groundbreaking for the building three months away, Thornton Tomasetti (structural engineer) engaged GEI Consultants, Inc. (wall design engineer) to design a 1,600-foot-long permanent soil and rock nail wall to support the excavation. The wall design engineer implemented a geotechnical exploration program immediately and began the design process, coordinating closely with Nicholson Construction (specialty"

Jan 1, 2017

By T. Kerr, C. Mattich, J. Wilson

"In refractory gold concentrates, gold is occluded in sulphide minerals preventing efficient cyanide leaching. Hence, roasting is used to oxidize sulphur and organic carbon, the latter being necessary to minimize recovery loss through the preg-robbing effect. In 2009, Outotec commissioned the circulating fluidized bed roaster at Syama gold mine in Mali. Since 2013 Resolute and Outotec have been implementing improvements to the roaster performance with the capacity increasing from 8000 t/month in 2013 to above 13,000 t/month in 2016, while achieving a residual sulphide sulphur and organic carbon contents of below 0.1 wt.% and 0.4 wt.%, respectively. Thus a gold recovery in the CIL of above 90% is attained. In 2016, Outotec audited the Syama roaster. The analysis resulted in the Low Carbon Roaster (LCR) upgrade concept which (i) allows re-processing of calcine dust from the spray cooler and ESP after pelletization and (ii) allows the roasting of a further fine-organic carbon rich feed, i.e. de-slime circuit tailings. The LCR upgrade aims to reduce organic carbon to <0.2 wt.% and increase roaster-leaching gold recovery by >3%. Project development included extensive testwork. The LCR process is expected to become operational during FY 2019.INTRODUCTION Double refractory sulphide ores exhibit the characteristics of gold locked within pyrite grains, in the presence of preg-robbing natural (organic) carbon. Hence, to achieve high recovery during subsequent processing steps, i.e. cyanide leaching, oxidation of sulphide sulphur is required, producing a porous calcine by way of a roasting step. This allows for the gold contained within the pyrite grains to be accessible during cyanide leaching. Furthermore, it is necessary to oxidize the organic carbon. Oxidizing the organic carbon is essential as gold recovery loss occurs as a result of gold-cyanide complexes being adsorbed on organic carbon, this phenomenon is termed as preg-robbing (Miller et al., 2016). The gold absorbed on the organic carbon is lost, reporting to the tailings stream. Hence, the aforementioned oxidation of sulphide sulphur and organic carbon is the process goal. Nonetheless, the latter must occur at a controlled temperature which is concentrate/ ore specific, since the pores of the produced calcine should not sinter, as this makes the gold contained in the calcine less accessible during leaching, leading to gold recovery loss. The tight temperature control requirement is a decisive factor in the choice of a Circulating Fluidized Bed (CFB) as the roasting reactor, due to the excellent mixing characteristics of the CFB which results in temperature homogeneity of (+/-10°C). Roasting of double refractory ores, as described above, can be included in the flowsheet after comminution and grinding, a process termed as whole ore roasting, or by including a flotation circuit termed as concentrate roasting. Roasting the flotation concentrate results in less solid flow, increased sulphide sulphur grade and organic carbon content resulting in a higher heating value and higher gold content. A typical composition of the Syama ore and concentrate is given in Table 1. Ore average values presented correspond to the period 2015, while concentrate values are typical for the flotation performance throughout the period 2012–2015."

Jan 1, 2017

By L. Bryson, J. H. W. M. Brits, K. Voogt

"The Anglo American Platinum’s Rustenburg Base Metals Refinery (RBMR) has the world’s first full deposit nickel plating tankhouse. Impurities in the nickel electrolyte can induce stresses in the electrowon nickel deposits that could lead to delamination of the deposit. Identifying the impurities that contribute to increasing internal stresses in the nickel deposit is key to successful operation and automation of the tankhouse. Impurities were introduced in the plant electrolyte and the effects on the full-scale nickel deposits evaluated. The impurity-adjusted electrolyte solutions were also analyzed using commercially available bench-scale methods to determine the induced stress. A correlation between impurity-induced deposit stress and full-scale delamination was developed. A direct correlation can now be made between feed quality, i.e. impurity concentrations, and degree of delamination in the plant. This methodology has the potential to rapidly predict the effect of new reagents, upstream process upset conditions and synergistic interactions between impurities on deposit stress and delamination of nickel deposits.INTRODUCTION Nickel electrowinning in sulphate media was first pioneered by Outokumpu in its Harjavalta refinery in 1960 (Saarinen and Seilo, 1985). The original process was very manual with starter sheets plated onto “acid resistant” steel for 36 hours and then manually stripped and cut into sheets which could be inserted into the main production cells for a further 4–5 days. The starter sheet stripping and manufacture process was later automated. The same technology was subsequently implemented on a number of plants around the world. Anglo American Platinum’s Base Metal Refinery (BMR) began nickel electrowinning in the early 1980’s. The recent expansion of Anglo American Platinum’s Base Metals Refinery necessitated the construction of a new nickel tankhouse to achieve two primary objectives. The first to increase the capacity to 32 400 tpa nickel and the second to reduce employee occupational exposure to nickel aerosols. The new tankhouse has been commissioned and is in the process of ramp-up; more details are given by Hagemann et al. (2016). Fundamental to lowering employee exposure to aerosols was automating both harvesting and final handling of cathode. In order to accomplish this a bold move was taken to plate up to 10 days on permanent titanium blanks which are harvested by automatic crane and automatically stripped. The original development work for the plating nickel on titanium blanks over a ten day cycle is given by Bryson et al. (2006)."

Jan 1, 2017

By Karsten Hagenah, Tor Jensen, Jens Laugesen, Øyvind Fjukmoen, Lucy Brooks

"The methods and technologies to be used for environmental monitoring of seabed mining activities are a key issue. Due to the large water depths, there are special challenges with respect to the monitoring equipment that is suitable. DNV GL has built up substantial experience of environmental monitoring from oil & gas projects in deep waters in the Norwegian Sea.Monitoring equipment and experiences from the oil & gas sector can to a large extent be applied to seabed mining.BackgroundThe International Seabed Authority is currently developing an environmental management strategy for the Area (ISA, 2017) as a part of the work on the regulations for exploitation for mineral resources in the Area.The draft environment strategy contains provisions related to monitoring and reporting of the activities. An Annex (Annex III) of the draft document describes the format and content of the environmental management and monitoring plan.The monitoring plan should contain, inter alia: ?Technology to be deployed.?Monitoring frequency of respective elements/components of the Marine Environment.?Monitoring procedures required to implement the Monitoring programme.?Details of the environmental monitoring stations across the Environmental Impact Area.?Monitoring specifics e.g. water quality; sedimentation rates; sound; plume extent; etc., as well as relevant Environmental Targets.?Monitoring of Mining Discharges.?Processes for Monitoring reviews and Environmental audits."

Jan 1, 2017