Search Documents

By H. M. Woodrooffe

IT IS WELL KNOWN that chrysotile asbestos from various occurrences exhibits varied physical properties and certain differences in chemical corn position, both of which conditions may have an important bearing on the industrial utilization of the fibre. The usefulness of a harsh fibre in the manufacture of asbestos cement products and of low-iron fibre for certain electrical uses are examples. It is also .possible to obtain a fibre with a texture too harsh and brittle to be of economic value. Much research into the structure of the mineral and to a lesser degree observations relating the water of combination to certain physical properties have ?been reported. This paper is an attempt to show that the pyrolysis of ?chrysotile takes place in three stages and that the conditions of pyrolysis are peculiar to the fibre and may afford some clue to the variations in physical properties of asbestos fibres which affect their utilization.

Jan 1, 1956

By R. A. Hatch

The United States depends mainly on foreign imports, principally India, for an adequate supply of sheet mica suitable for its many uses in the electrical and electronics industries. Sheet mica has, in fact, played an indispensable role in developing these industries,4/ and, in turn, the products of these industries (radio, radar, electric motors, and many others) have become indispensable to the military forces. Because or these conditions, sheet mica in its better qualities long has been classified as a strategic and critical material, and from this stems the wide-spread interest in substitute materials of which synthetic mica is one potential type. The United States Departments of the Navy and the Army entered into a cooperative agreement with the Bureau of Mines in 1947 to study ways and means of synthe-sizing and growing mica crystals. This is one of a series of reports5/ that describe the results of this program.

Jan 1, 1956

By R. A. Campbell

The electric smelting of five lowgrade Canadian manganese ores has been investigated at the Mines Branch, Department of Mines and Technical Surveys, Ottawa. Ferromanganese, silkomanganese, and spiegeleisen were produced 1by special smelting processes from these ores since the latter were too low grade to be treated by conventional smelting methods. In one case the results were considered to be sufficiently promising to justify the construction of a pilot plant, by the Company concerned, for the further development of the process.

Jan 1, 1956

By C. E. Lesher

Two processes for agglomerating fine sized ores with low temperature coke are described. One process (Orcarb) agglomerates ores with limited amounts of carbon; the other (ore-carbon pellets) pelletizes fine sized ores, using low temperature cokes as the binder. Data are presented on the products obtained when taconite, magnetite, and hematite concentrates and several titanium oxide ores were used. REDUCTION of finely divided oxide ores has long been a major metallurgical problem. Various methods of agglomerating, notably briquetting, sintering, nodulizing, and pelletizing, have been developed and are in industrial use. Carbon is the usual reducing agent for oxide ores and attempts have been made to agglomerate fine ores with coking coal in order to get the metallurgical advantages of intimate contact and increased particle sizes suitable for subsequent smelting or reduction.1-3 For the past three years, research has been in progress on two processes for combining fine sized ores with reactive carbon in the form of low temperature coke. By one process, designated Orcarb, the ore is coated with coke carbon in amounts limited to that required for reduction and the result is an appreciable but limited increase in product particle size over that of the original ore. The second process, called ore-carbon pellets, produces pellets of fine ore bound by low temperature coke. The first objective was to develop a process for combining an oxide ore with only enough carbon for its reduction, the amount being that derived from the simple reduction equations. The carbon (that amount theoretically required for the reduction of the oxides in an agglomerate with ore), calculated to CO, ranges from 10 pct for zinc calcines or phosphate ores to 21 pct for rutile and 26 pct for silica. The carbon required for reducing iron oxides falls between the extremes—10 and 26 pct. When the carbon in the agglomerate is low temperature coke, reduction by hydrogen may be expected to take place, thus modifying the calculated carbon require- ment. On the other hand, in practice, an excess of reducing agent over that required in theory is normally used. Screen sizes of three iron ores on which the greater part of the experimental work was performed are given in Table I. Most of the testing was done with Freeport (Renton Mine) coal, but Pittsburgh and Elkhorn bed coals were also used. The first objective was to agglomerate the ore with sufficient low temperature coke to provide carbon for reduction, i.e., in the range from 10 to 25 pct. This was accomplished by preheating the ore, mixing with pulverized coking coal, and completing the coal carbonization in a plain steel rotating retort. The pilot retort, as it is now constituted, is shown by diagram in Fig. 1 and photograph, Fig. 2. Ore is fed into the upper kiln by a screw; it is heated to 900" to 1100°F by direct flame and it is then discharged into an insulating hopper from which it goes

Jan 1, 1956

By R. W. Huber

The successful development of a titanium prototype of the 81-mm. mortar base plate for the Army Ordnance Corps is outlined in this report. Information is presented dealing with forming, forging, and machining, welding and assembly techniques, and design changes relative to this prototype. INTRODUCTION The work of the Federal Bureau of Mines in making ductile titanium available2/ has resulted in the establishment of a new industry. Owing to its strategic importance and the combination of low density and high strength, titanium has received considerable attention as a structural metal. Titanium's favorable strength-to-weight ratio is of particular importance to the Army Ordnance for equipment that is transported by airplane or by foot soldiers.

Jan 1, 1956

By C. S. Allbright

This report gives the results of analyzing three groups of crude shale oils by the Bureau of Mines procedure:4/ (1) Oils produced by standard Fischer assay determinations on oil shales from Brazil (Paraiba Valley) and the United States (Colorado); (2) oils produced from Brazilian shale by different retorting methods; and (3) oils from high-temperature retorting of Colorado oil shale in the Entrained Solids retort. It is the second in a series presenting data obtained by analyzing crude shale oils from various sources. The series furnishes information on the general characteristics and compositions of a wide variety of shale oils. Use of a standard analytical method on all samples facilitates comparison of different oils. The 18 oil samples analyzed in this project comprised 3 from assays of Brazilian and Colorado oil shales in the Fischer retort, 9 obtained by processing Brazilian shale in various other units, and 6 from entrained solids retorting of Colorado shale at 1,000° to 1,500° F. The crude oils from Brazilian shale contained about half as much nitrogen as the Colorado oils. Properties of the Fischer assay oils from Colorado shales agreed with some data that relate grade of the oil shale with properties of the crude oil from the Fischer assay. Comparison of results from Fischer assays of oils from the foreign and domestic shales shows that the oil from Brazilian shale contains more low-boiling material and less residuum than either of the two from Colorado shale. This fact is reflected in lower specific gravity, viscosity, and carbon-residue values for the Brazilian oil. Retorting Brazilian shale in the Entrained Solids unit at 1,120° F. produced an oil whose boiling range was generally lower than the boiling ranges of oils obtained by processing in three other retorts at conventional temperatures. The quality of crude oils from high-temperature retorting of Colorado shale in the Entrained Solids process varies with retorting temperature. As the temperature is raised within the range 1,000° to 1,500° F., the amount of the naphtha fraction in the crude oil increases to about 35 percent and the aromaticity to 98 percent.

Jan 1, 1956

By O. C. Blade

This report on the properties of burner-fuel oils produced during 1956 was issued under a cooperative agreement between the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, at the request of the Oil-Heat Institute of America and the petroleum industry. This survey is the second for this type of fuel, the first being made in 1955. 2/ The surveys are conducted to provide information on the characteristics of burner-fuel oils now manufactured for sale. They are similar in pattern to the diesel-fuel surveys, conducted since 1950, 3/ and are not intended to conflict with but rather to supplement them. The importance of fuel oil has resulted in the need for more information by the petroleum industry, manufacturers of heating appliances, and consumers regarding the types and qualities of the fuels currently being marketed. Samples of burner-fuel oil typical of their manufacture during the early part of 1956 were analyzed by the refiners in accordance with instructions from the subcommittee on fuel surveys of the Automotive Research Committee of the American Petroleum Institute, Results of the analyses were transmitted to the Bureau of Mines where the data were studied and compiled as shown in the tables of this report.

Jan 1, 1956

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1955 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 116 samples of aviation gasoline and for 38 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers' 1955 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 16 producers of aviation jet fuels are represented.

Jan 1, 1956

The presence of undetonated explosives in a rock face after firing constitutes a hazard which can result in a fatal or serious accident if undetected before drilling commences.Most accidents caused by drilling into explosives are the result of failure to examine the working face properly and lack of care in subsequent drilling operations; it is not always realized that explosive may be left in the butts of holes or may be driven into cracks or crevices in the rock.Obviously the best means of preventing accidents of this nature is to adopt methods of drilling, charging and firing which will reduce the hazard to a minimum.There are three ways in which undetonated explosives may be left in the rock face, namely:1. Misfires.2. Cut-off shots.3. Incomplete detonation or failure of the charge to propagate throughout.MisfiresNo attempt will be made in this paper to deal fully with the question of the prevention of misfires, as apart from the fact that most of the preventive methods are well known, it is believed that if the miner receives his explosives and means of initiation in good order, and proper care is taken in their use, the failure of a charge to fire will be a rare occurrence. The provision of central fuse capping stations on mines has gone a long way towards the elimination of misfires caused by the mishandling of safety fuse anddetonators.

Jan 1, 1956

By E. R. Palowitch

This report is the result of a series of coal-cleaning tests using a dense-medium cone-type washer. Detailed results are given for 2 tests using a magnetite medium and 4 tests using a pulverized-refuse medium. Approximately 120 float-and-sink tests and over 500 separate chemical analyses were made in conjunction with these tests. In these tests higher recovery efficiencies and sharper separations were obtained when using a magnetite medium, especially on coal sizes below one-half inch. When sizes above 1 inch at low specific gravities of separation are cleaned, the pulverized refuse medium compared favorably with the magnetite medium.

Jan 1, 1956

By B. E. Blair

The physical properties and related geological and petrographic data for 81 rock types obtained from operating mines or selected test sites are presented in this report. Most of these rock data were obtained to supplement structural studies in underground mines; however, the data may be equally applicable to other problems where the physical properties of rock are an important factor. Stress-strain curves are presented, where available, and free medium velocities from laboratory and field measurements are compared for several rock types. Rock-type, geographical, and geo-logical indexes are included for reference relative to physical property data in this and previously published Bureau of Mines physical property reports. INTRODUCTION This report presents the physical properties of 81 rock types from 16 different projects (sections 53-68). Three previous physical property reports2 3 4/ (herein after referred to as parts I, II, and III) presented data on 244 rock types from 52 project areas. (Part I included sections 1-25, part II sections 26-36, and part III sections 37-52).

Jan 1, 1956

By D. J. Carney, E. Van Meter, J. J. Oravec

A study was made of combustion-air temperatures and factors affecting air temperatures in the open-hearth regenerative systems. Air-temperature surveys in the regenerative system revealed marked thermal gradients in the air above the checkers. The design of the fantail-uptake region plays a prominent part in increasing the heat recovery of the regenerative system. THE efficiency of the open-hearth regenerative system is one of the most important factors affecting open-hearth performance. Until recently, this factor has not received the attention in the literature given to many other items affecting performance, such as the type of charge, speed of charging, and the mechanical equipment of the open hearth. J. S. Marsh' emphasized the importance of the flame temperature and its dependence upon the combustion-air temperature. By means of measured air temperatures in open-hearth furnaces, data were presented which showed a remarkable degree of correlation between production rate and combustion-air temperature. This correlation was extremely good in view of the numerous factors, other than air temperature, which affect open-hearth production rates. In Marsh's work, a 100°F increase in air temperature reduced the heat time by approximately 45 min. Realizing the importance of combustion-air temperature, it is desirable to know which factors control the regenerative efficiency of the open-hearth furnace. B. M. Larsen recently discussed this subject.' The present paper illustrates a few of the more important items that affect regenerative efficiency and combustion-air temperature. In the latter part of 1951, a study of open-hearth combustion-air temperatures was begun at the South Works of the United States Steel Corp. In the initial work at open-hearth shop X, which produces low carbon steel products, temperatures were measured in the uptake in a manner similar to that used by Marsh' and the results obtained were very similar to the Bethlehem data. When it was decided to expand the study of combustion-air temperatures, open-hearth shop Y was selected because of the greater variety of furnace-design features, types of steel produced, and firing rates used. With the use of aspirating thermocouples, continuous gas analyzers, thermocouple and optical pyrometers, a study was made of: 1—effect of combustion-air temperature on open-hearth production rate, 2—thermal gradients present in various zones of the regenerative system, 3—effect of furnace-design variations on air temperature and heat recovery, 4-—effect of furnace-operating variables on heat recovery, and 5—variation in heat recovery with furnace age during the normal furnace campaign. Data collected on individual heats at 15 min intervals included air-flow rate, firing rate, checker temperature, combustion-air temperature, and furnace pressure. These data were collected on approximately 230 heats of steel. In addition, information was obtained at random on air infiltration and combustion-gas compositions. The data gathered have shown the desirability of closer control of open-hearth firing practices, a need for reducing air infiltration in the uptake zones, and a need for further study of design of checkers and of uptake-fantail areas. Equipment Air is practically a nonradiating medium. Consequently, in the measurement of air temperatures, the principle of heat conduction must be used rather than heat radiation. For this reason, aspirating-type thermocouple pyrometers normally are used to measure air temperatures. With these devices, air

Jan 1, 1956

By W. J. Crawford, P. M. Gruzensky

"Several experiments have been carried out in efforts to evaluate qualitatively a variety of electrolytes for refining bismuth. Most extensive work was done with the basic tartrate, hydrochloric acid, and hydrofluosilicic acid electrolytes. Deposits that are smooth and adherent can be obtained from these three electrolytes if low cathode current densities are employed. All three electrolytes were effective in purifying crude bismuth considerably, with additional purification indicated in each instance by a reelectrolysis step.With the basic tartrate electrolyte best results were obtained when the electrolyte was at 40° C. and contained at least 100 grams of bismuth per liter. An apparent disadvantage was depletion of bismuth from this electrolyte, causing the deposits to become spongy and nonadherent.The hydrochloric acid electrolyte had the greatest tendency to yield rough, dendritic deposits. Best deposits were obtained at cathode-current densities below 2 amperes per square decimeter. A small amount of glycerin helped to produce a smoother deposit, and adding sulfuric acid or methyl sulfuric acid retarded the deposition of impurities. Very good results were obtained in electrowinning bismuth from a bismuth trichloride-hydrochloric acid electrolyte.Smooth and adherent deposits were obtained from a hydrofluosilicic acid electrolyte, with very good refining as regards lead and silver impurities; however, higher reagent costs and slow decomposition of the electrolyte have discouraged its use.INTRODUCTIONMethods of recovering bismuth from ores and byproducts were underdeveloped for many years because of the limited uses for bismuth, the pharmaceutical industry being the chief consumer. In the past decade or so additional uses for bismuth, particularly in the metallurgical field, have brought about increased demand for the metal with the result that bismuth is being recovered from byproducts that were once discarded. In addition to such uses as low-melting alloys, solders, bearings, die setting, etc., some interest has been indicated in bismuth as a possible coolant for nuclear reactors. The advent of ductile bismuth and bismuth-alloy thermocouple wire has contributed greatly to temperature measurement, particularly in the below-zero range."

Jan 1, 1956

By E. E. Harton

Bureau of Mines Information Circular 7516, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants, was published in October 1949 to aid in estimating investment and operating costs of processes for manufacturing synthetic liquid fuels. Development of such processes by the Bureau of Mines was authorized by Public Law 290, 78th Congress. This bibliography included references to and abstracts of publications appearing from. 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. Bureau of Mines Information Circular 7705, Supplemental Bibliography on Investment and Operating Costs for Chemical and Petroleum Plants, was prepared to cover the area from September 1948 through June 1952.

Jan 1, 1956

By Manuel Gomez

Primary, low-temperature tars are generally known to alter with time. The effect is believed to occur, in some instances, without the external influence of air, light, or heat. Since one of the processes occurring during extended storage is oxidation, the action of mild oxidation induced by air and heat, in addition to the effect of storage, was studied. The principal effect in aging and oxidation is formation of pitch at the expense of the distillate fraction. The fraction boiling above 270° C. is mainly involved in pitch formation due to storage, whereas all fractions are affected to some degree when tar is heated at 125° C. in the presence of air. If the effects of air are considered, the aromatic and tar-acid fractions seem to be important in pitch formation.

Jan 1, 1956

By C. W. Owings

One phase of Bureau of Mines health and safety work is promotion of the use of safe and effective dust-collecting devices in connection with rock drilling in coal mines. To insure that adequate equipment of this type is available to the coal-mining industry, the Bureau of Mines conducts investigations and issues approvals for dust-collecting equipment that meets the requirements of a schedule established for testing dust collectors intended for use in connection with roof drilling for roof bolting and for other rock drilling. 6/ Performance tests are conducted under the provisions of this schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for approval and lists drill-dust collectors that have been granted approval as of January 31, 1956. The addresses of manufacturers of approved devices are listed alphabetically at the end of this circular.

Jan 1, 1956

By E. O. Lilge

THE USE of the Driessen cone as a heavy-media concentrator involves a mineral dressing process in which many variables inherent in the ore and in the process may have an effect on the efficiency of mineral separation and the operation of the cone. The magnitude of these effects and their possible interrelationships must be known before a full-scale plant can be designed and built. It appears that, among the most important variables, are the following: Ore Variables: The particle size of feed The difference in specific gravity between economic and non-economic minerals The intimacy of mineral association Cone Variables: Cone inlet area Ore to media ratio Cone ratio Size distribution in heavy media Specific gravity of media Viscosity of media Type of media

Jan 1, 1956

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and from the data developed, to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke regardless of preparation. This report is one in a county series that describes the preparation characteristics of the coals of Mingo County, W. Va.

Jan 1, 1956

By J. P. Walsted

Offgrade chromite concentrate, with a Cr-Fe ratio of 1.3 to 1.4 has been successfully smelted to produce useful ferroalloys. The Cr-Fe ratio is not improved, but the alloys can be used without a too drastic change in normal steel-mill practice. The ordinary high-carbon ferrochrome has been successfully produced by smelting under highly acid smelting conditions. An alloy containing 50 percent chromium was produced at a power consumption of 4,490 kw.-hr. per ton of alloy. Alloys containing 20 percent silicon were made by direct smelting chromite concentrate and silica.

Jan 1, 1956

By J. J. Hoeppner

Lignite samples were collected so as to be widely representative of the extensive deposits in the western north-central area. These were carbonized at temperatures ranging from 450° to 550° C., according, to a standardized procedure. In general, product yields varied; extremes obtained on selected samples show char recoveries on the moisture- and ash-free basis as 56.7 percent for slack lignite or "leonardite" to 80.8 percent for a concentrate of the fusain component from a typical face sample; normal lignite samples averaged approximately 70 percent. Tar-plus-light-oil yields ranged from 3.3 percent for the fusain concentrate to 11.0 percent for a normal sample, averaging approximately 8 percent; gas recoveries varied more widely both in yield and in composition, ranging, from 10.0 percent to 27.7 percent, the latter being from leonardite and quite high in carbon dioxide. Sampling was conducted with the view of representing, as nearly as possible, all beds delineated by Brant (2);4/ many are necessarily missing since collection was confined largely to worked deposits. Data presented in this report indicate a general uniformity of North-Central lignite in respect to low-temperature carbonization, with a few possible exceptions of a local nature. When processed according to the indicated conditions, maximum tar yield may be realized with minimum loss of recoverable heating value of the original coal. Natural weathering of lignite, however, does affect tar yield adversely and should be held to a practical minimum in any commercial operation.

Jan 1, 1956