Search Documents

By R. C. A. Thurston

AT A FATIGUE SESSION organised by the A.S.T.M. in 1949, R. E. Peterson presented a brief introductory paper ( 1) in which lie referred to a discussion on the fatigue of metals which took place in England in 1849, and then proceeded to review some of the subsequent researches concerning the mechanism of fatigue. In the course of the review, he discussed metallograpl1ic studies with single crystals and polycrystalline materials, studies with X-ray methods, and the application of the electron microscope. During that hundred-year period considerable progress was made toward a better under-standing of the nature of fatigue, although it is probable that even greater attention was directed to the more practical aspects of the problem, such as the effects of notches, temperature, corrosion, surface treatment, residual stresses, and so on. Since then there has been an appreciable acceleration in the tempo of the fundamental work, partly influenced by the rapid development of the theory of dislocations, with the result that our knowledge of the mechanism of slip, the initiation of fatigue cracks, and their subsequent propagation, has still further advanced, although it is by no means complete as yet. The present paper is an attempt to out-line the more recent developments in these basic studies, to correlate them when possible, and to draw attention to those directions in which research might profitably be pursued.

Jan 1, 1957

By J. G. Kirby

According to the Bureau of Mines annual survey, there were 319 petroleum refineries in the United States as of January 1, 1957 capable of processing 9,123,674 [ ]-barrels of crude oil daily. This was the first time in eleven years that the total number of refineries increased. The crude throughput capacity of the refineries increased 491,284 barrels daily (6 percent) above the January 1, 1956 capacity. The East Coast and Texas Gulf Coast refining districts accounted for 60 percent of the additional capacity installed. Three new refineries were put into operation on the East Coast during the year with a total daily crude throughput capacity of 154,434 barrels while the other refineries in the district report a net loss in capacity, installing equipment capable of processing 140,000 barrels, but dismantling equipment with a capacity of 150,100 barrels. In the Texas Gulf Coast district, one new refinery with a daily crude oil capacity of 5,000 barrels was placed in operation in 1956 and 143,700 barrels of crude capacity was added to existing refineries. The capacity of the average refinery to process crude oil increased from 27,145 barrels daily to 28,601 barrels in 1956.

Jan 1, 1957

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: (a) Which coals, either as mined or after beneficiation by conventional preparation, are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in a county series and describes the preparation characteristics of the coals of Logan County, W. Va. According to present-day standards for metallurgical coal, many believe that the sulfur content of the coal should not exceed 1.25 percent? Coal with more than this amount has been used for making metallurgical coke, especially when blended with coal containing less sulfur. In this series of reports 1.25 percent sulfur is used as a gage to determine whether or not a coal will be suited for metallurgical coke.

Jan 1, 1957

By V. C. Petersen

The titanium-rich end of the titanium-germanium system was investigated by x-ray and metallographic methods and verified by resistivity and dilatometer measurements. A constitution diagram is proposed. The titanium-rich portion of the phase diagram is characterized by eutectic and peritectic reactions. The eutectic composition is 19 percent germanium, and the eutectic temperature 1,360° C. The peritectic reaction occurs at 905° C. and 4 percent germanium. Germanium is soluble in alpha titanium to a maximum of 4 percent at 905° C. and in beta titanium to a maximum of 12.5 percent at 1,360° C. Both limits of solubility decrease with decreasing temperatures. Although substantial quantities of germanium are soluble in beta titanium, beta is not retained on quenching. The beta phase probably transforms to alpha by a martensitic reaction.

Jan 1, 1957

By Irving Hartmann

The Experimental Coal Mine of the Bureau of Mines has served principally as a valuable and unique testing laboratory for studies of the explosibility of coal dust and mine gas; studies of the numerous complex and interrelated chemical and physical factors that govern the ignition of coal dust and the propagation of mine explosions; and studies designed to develop measures for preventing explosions or reducing their destructive effects. These researches, coupled with educational efforts by the Bureau of Mines and enlightened safety consciousness in the mining industry, had fruitful results. This is evidenced by the remarkable reduction in the frequency of major coal-mine explosions and the number of fatalities from explosions since the Bureau of Mines was established. Despite this progress, further important unresolved problems arise; these are due in part to changes in mining conditions and methods, which have brought about increased production of fine coal dust in highly mechanized operations. To solve the new problems, research must be continued without interruption. The results of many very recent and current studies in the Experimental Coal Mine are summarized briefly, and pertinent studies by European mine-safety-research organizations are listed.

Jan 1, 1957

By A. G. Starliper, H. Kenworthy, A. Ollar

Vapor pressure determinations were made on synthesized germanium sulfides. Germanium and cadmium were removed from sphalerite concentrates by fuming. The fume was retreated to separate some of the cadmium from the germanium and, at the same time, upgrade the germanium to more than 5 pet content. MANY sphalerite concentrates contain certain impurities which have economic value as byproducts. These may include the volatile sulfides of germanium, cadmium, and lead. The objectives of the research reported in this paper were to study the fundamental volatility characteristics of germanium sulfides, to increase the recoveries of ger-

Jan 1, 1957

By E. A. Magill

The Bureau of Mines has begun a study of the copper resources of the Cascade Mountains of Washington. The program includes reconnaissance of mineralized areas and examination and occasionally limited exploration of deposits that are considered characteristic of an area. The Bureau of Mines believes that published information may assist industry in searching for new sources of copper. The Miners Queen is one of a few Cascade Mountain deposits selected for prelim¬inary exploration. The investigation was not planned to delineate the ore body. A diamond-drilling program was carried out at the Miners Queen mine in the summer of 1955. Five diamond-drill holes were completed, totaling 628 feet. Two 35-foot shafts were dewatered, and all accessible underground and surface workings were examined.

Jan 1, 1957

The Wednesday Morning Session of the Rocky Mountain Coal Mining Institute was called to order by Albert Keenan of the Thompson Creek Coal and Coke Company, Denver, Colorado, in the absence of the President. He introduced Edward Prostel of the University of Wyoming Natural Resources Research Institute, Laramie, Wyoming, who spoke on "Coal Utilization Work at the University of Wyoming." (Please refer to the index for printed text of the paper.) Following Mr. Prostel's talk, R. Park Lamborn of the National Mine Service Company, Pittsburgh, Pennsylvania asked Mr. Prostel two questions: (1) What -has been done in tar research? and (2) Has there been large scale research on brickets? Mr. Prostel stated that he could not say too much about the first question as this research was done in the petroleum department and he would prefer to have a chemist talk about it. As to the second question, the system of carbonization is a big project. There are many possibilities. At the University they are trying to do that in the same unit that produces the char. This system was introduced in Canada. The brickets are bound with sulphite liquor. Mr. Schloss asked Mr. Prostel to report on a project that they have been working on at the University, and Mr. Prostel stated that some time ago they began to experiment to see if it would be economically possible to dry coal at the mine (coal containing 30% moisture) and then ship it a distance of 130 miles to be used. Results are that it would be possible, but will require a considerable quantity. He felt it might be possible to operate such a scheme in a few years.

Jan 1, 1957

By W. Dan Walker

In recent years the Federal Bureau of Mines tested and approved four new types of self-contained breathing apparatus and a facepiece designed for use with the McCaa 2-hour self-contained oxygen breathing apparatus. The Bureau also developed and perfected a battery-powered lifeline telephone for use in mine rescue and recovery operations. Some of this equipment is described in Bureau of Mines Information Circular 7413.4/ This publication is a revision of information Circular 7413 and presents pertinent information on more recently developed mine rescue equipment. The breathing apparatus described herein are 1/2- and 3/4-hour sell-contained types of much simpler design than the conventional 2-hour self-contained oxygen breathing apparatus ordinarily used by mine rescue crews; however, it is just as important to select rescue crews carefully and to train them properly in the use, care, and limitations of the newer types of apparatus as well as the older, established types, if the newer types are to be used safely. The Bureau of Mines recommends that 1/2- and 3/4-hour self-contained breathing apparatus be used only as auxiliary equipment in mine rescue and recovery work and that the capabilities and limitations of the apparatus should be well understood by those who wear the equipment.

Jan 1, 1957

By John T. Norton

N order to attempt to arrive at a better under-Jl standing of the whole basic problem of sintering, these remarks will serve as an introduction for discussion that is included and will, perhaps, help to isolate specific questions which need to be answered or to suggest some definite avenues of investigation which should be followed. To bring some sort of logical order into the presentation, I will consider the various types of interaction between the metal to be sintered and the atmosphere which surrounds it, depending upon whether the phenomena are essentially chemical or physical in nature. For example, when the only necessary criterion for the satisfactory sintering of a certain powder is the removal of an oxide skin, then the problem of choosing a suitable atmosphere is primarily chemical; however, if a special surface condition as a consequence of the oxide skin removal is necessary for particularly effective sintering, then the problem becomes a physical one. Of course, the two aspects overlap considerably, but it may be possible to make a distinction in principle if not in practice. The chemical characteristics of the phenomena will be emphasized, since these are the better known. Metal-gas reactions involved in sintering are controlled primarily by the thermodynamics of the processes involved. In which direction will a reaction go and how far before it stops? The answer is to be found in the magnitude of the free energy change associated with the reaction. If a constituent is to be removed from the specimen as completely as possible or if a constituent is to be formed in the specimen as completely as possible, then one chooses conditions which are far from equilibrium so that the reaction is driven toward completion. On the other hand, if the composition is to be maintained at a desired value, then conditions are adjusted as closely as possible to the equilibrium point. This aspect of the problem is susceptible to quite precise analysis, provided, of course, that the significant reactions can be recognized and the required thermodynamic data are available. Conversely, if one asks how fast the reaction goes or how far it proceeds in a given time, the answer is frequently much more difficult to answer in quantitative terms. Yet the rate-con trolling factors of the reactions may be of primary importance in the success of a particular operation, especially where competing processes are at work. Both equilibrium and rate factors must be understood if a clear picture is to be obtained. For instance, in a process for carburizing titanium dioxide, is the difficulty of obtaining a stoichiometric Tic due to a true limitation of the equilibrium or simply to a very slow rate of reaction? An example of this appears in the work of Kalish and Mazza.' They showed that the oxygen content of sintered iron compacts was lower when sintered in pure hydrogen than in the case where the hydrogen was diluted with either argon or nitrogen. The equilibrium oxygen content of the iron would be the same in the two cases, since it is determined by the ratio of the partial pressures of water vapor and hydrogen and this pressure ratio is unchanged by dilution. The rate of oxygen removal, however, under the conditions of a constantly replaced furnace atmosphere, depends upon diffusion and thus upon the concentration of hydrogen in the furnace atmosphere. Possibly the clearest way to illustrate the interplay of these two factors is to consider in more detail some of the typical metal-gas reactions. Adsorbed Gases It is common experience that fine metal powders with their very large surface areas often contain large quantities of gas. This gas, which results from exposure to air or perhaps from some step in the

Jan 1, 1957

To finalise the arrangement and details of the headframe to be erected over the new No. 3 Shaft, the haulage and winding equipment requirements were first determined, then tentative designs were prepared to cover the needs of general shaft servicing work for men and materials, mullock and ore handling, and the probable requirements of a breaker station to be built adjacent to the headframe, which would provide for the crushing of the run-of-mine ore down to a size which would be suitable for feeding on to the concentrating mill.

Jan 1, 1957

By S. S. Clarke

This paper on methods and costs of mining at the Westside mine, in the Tri-State zinc-and lead-mining district (Missouri-Kansas-Oklahoma), is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in various mining districts of the United States. Methods and equipment used in drilling, loading, and underground transportation have changed radically since the latest Bureau of Mines publications2/ on mining methods in the district were published more than 20 years ago. More efficient methods and machines have been developed in order to maintain low operating costs in the face of rising labor and supply costs and lower grade ore. The rate of conversion to mine mechanization was disappointing at times; local conditions required the development of special equipment, and available rock-moving machines had to be remodeled and strengthened.

Jan 1, 1957

A calibration of the Frantz isodynamic magnetic separator relates the current in the electromagnet and the transverse slope of the chute to the specific susceptibility at which separation is being effected. In addition to providing a rapid measure of the specific susceptibility of minerals and composite grains, the calibration provides a guide to operation of the Frantz isodynamic separator for mineral separation, and to the nature of composite grains. The most sensitive magnetic separation is obtained by using the highest practicable current and transverse slope, and the lowest practicable longitudinal slope.INTRODUCTIONProbably all minerals have a magnetic susceptibility measurable by sensitive techniques. However, magnetic separation between minerals which have low but different specific susceptibilities, and which for many purposes are considered essentially non-magnetic, has only become practicable with the development of the Frantz isodynamic separator.The construction and principle of this highly sensitive separator has been described by S. G. Frantz as an appendix to a description by 'Gaudin and Spedden (1943) of its application to the separation of sulphides constituting mill products.Various publications (e.g. Hess, 1949, Hutton, 1952) refer to its use in separating the mineral constituents of rocks, ores, and unconsolidated sands.As used in this study the Frantz isodynamic separator consists of a vibrating chute mounted centrally between the pole pieces of an electromagnet (Fig. 1). This unit may be inclined in any direction by the universal mounting, and the electromagnet current is continuously adjustable from 0 to 1·5 amperes.

Jan 1, 1957

By B. F. Peters, J. Gordon Parr, E. R. Macgregor

A SERIES of seven hypoeutectoid alloys, up to 18.2 atomic pct Mn, was made by the levitation melting technique. The loss of weight on melting was considered to be entirely due to volatilization of manganese, and compositions were computed on this basis. Filed samples (—200 Tyler mesh) were helium quenched from 1000°C after soaking for 5 min by a technique already described.' Quenched Alloys -Assessments of the amounts of a phase produced and the hardness of the quenched alloys are summarized in Fig. 1. The experimental techniques and calculations involved have been described previously. The amount of a decreases as manganese content increases, until at 10.6 pct Mn only a trace of a' is observed. Previous

Jan 1, 1957

By John M. Campbell, W. E. Portman

A series of correlating charts have been prepared to enable the field engineer to predict the amount of stock tank fluid produced by stabilization of first stage separator fluid. The charts shown are particularly convenient for estimating the relative effect of temperature and pressure in economic studies. Further work is planned to investigate the factors affecting stage separation' yo supplement this preliminary work. The direct correlation of separation variables is dictated as a convenience to eliminate the trial and error calculation necessary when using the standard flash vaporization equations. These are obtained by a material balance using the equilibrium vaporization ratio K, and have appeared in the following, or similar. form many times in the literature. where La = mols of any component n in the separator liquid Ko — equilibrium vaporization ratio for any component at separator pressure and temperature Fa = mols of any component n in the feed Vn = mols of any component n in the vapor V = total mols of separator vapor These equations may of course be effectively and accurately solved by use of digital and analog computers. However, these are not usually readily available in field offices and the need often arises for fast results during routine operational problems. Consequently, many methods have been devised in an attempt to simplify the basic calculation.2-14 The methods proposed are generally satisfactory, but do not eliminate trial and error methods and the necessity of subsequent calculations to obtain the answer in volume terms. The purpose of this work. therefore, was to develop accurate charts that would give the result directly in gallons. When using stage separation the recoveries would be lower than those shown, for stabilization usually gives about 95 + per cent recovery on the potential stock tank components in the separator liquid. The recoveries are shown in terms of a 14 psi Reid Vapor Pressure product which has a true vapor pressure of 14.7 psia at 98°F. Consequently, this product represents a stable stock tank liquid under normal storage conditions. To estimate natural gasoline re- coveries by stabilization the volume shown may be multiplied by 1.20 for 18 Ib RVP natural gasoline and 1.36 for 26 lb RVP natural gasoline. PROCEDURE The five analyses shown in Table 1 were chosen since they were representative of wellstream compositions often found and had almost the same propanes plus liquid content, expressed in gallons per 1,000 std. cu ft of wellstream. The distribution of the components though is widely variant. A temperature range of 0-100°F. and a pressure range of 200 to 1,250 psia was chosen inasmuch as most separations fall within these limits The K values used were modified values of those originally published by Katz and Hachmuth.' In the range chosen these have generally given good results when predicting fluid recoveries. The choice was somewhat arbitrary, for the authors' personal experience has shown that

Jan 1, 1957

By Wilbur A. Haley

One of the purposes of the investigation was to determine and report on how coal augers are used to mine bituminous coal that is near outcrops and may not be mined otherwise by any other present-day method. Such increased overall recovery results in the conservation of coal resources. Other reasons for the investigation were to determine and report the production rates of such operations and the types of equipment used. Auger mining of coal as a means of coal recovery supplementary to strip mining has been introduced and developed since World War II. This type of coal mining has grown rapidly, and bituminous-coal production by auger mining has been estimated at 6,000,000 tons in 1955. Mines were selected for study to give reasonably representative information on auger mining in different types and thicknesses of coal beds in different geographic areas and on different types and sizes of equipment operated under various conditions. This report is based on field studies of 8 auger-miming operations in Pennsylvania, West Virginia, and Ohio and in 5 different coal beds. Operations were observed in active strip mines, in strip mines reopened for auger mining, and along benched coal-bed outcrops. At the time of this study, no augers were reported to be operating in underground mines. The diameters of holes drilled ranged from 26 to 52 inches, and the lengths of holes ranged up to 208 feet. At some operations auger holes often penetrated abandoned underground mine workings.

Jan 1, 1957

By J. B. Rosenbaum

This report presents new findings and consolidates previously published data to provide a single reference containing a concise and comprehensive description of the Bureau's work on electrolytic chromium. Two separate systems for electrolytic-chromium recovery were developed, one designated as the oxidized system the other as the reduced system. The electrowinning of chromium metal follows the dissolution of chromium from the ore or from ferrochrome and its separation from gangue and metallic impurities. Chromite was first solubilized by pressure digestion at slightly elevated temperatures in an oxidized acid solution using Na2Cr2O7 as an oxidizing agent. Later it was found that a sodium-free electrolyte was preferable, using return-cell anolyte containing H2SO4 and Cr03 as the oxidizing agent. Gangue materials were separated from the soluble metallics by filtration; and, after the Cr+3 had been stabilized, the metallic impurities were separated as crystalline ammonium salts by vacuum crystallization.

Jan 1, 1957

By P. W. Neurath

IN recent years the domain theory of ferromag-netism has been put on a sound experimental and theoretical basis. But its application to one of the most widely used high quality magnetic materials, the cold-rolled grain-oriented 3 pct Si-Fe used in transformer cores, has been rather difficult because of the complexity of the domain structure of the poly crystalline sheet material. This paper presents some experimental data for this material, showing the relation between plastic and elastic stresses, 60-cycle watt losses, and the domain structure as observed visually. Only a very tentative qualitative explanation of the effects will be attempted. Some initial results were reported earlier.'

Jan 1, 1957

By V. A. Nieberlein

An extractive process was developed applicable to submarginal titanium deposits containing valuable minor constituents; such as columbium (niobium) and iron. The process consisted of reducing the mineral concentrate with coke at high temperature to form a carbide-suboxide sinter, chlorination in the 400° -500° C. range, and fractional condensation of the chlorides. The chlorination procedure recovered 97, 83, and 87 percent of the titanium from brookite, rutile, and ilmenite sinters, respectively, while simultaneous columbium recoveries on the same materials were 85, 50, and 87 percent.

Jan 1, 1957

By Oren C. Baptist

[Several new oilfields have been developed in northwestern Wyoming during the past 10 years, production is obtained from discontinuous, permeable sands enclosed within impermeable shales. The energy to drive the oil to producing wells in supplied by gas in solution in the oil. Most of the wells had high-initial potentials, but rates of oil production have steadily declined, indicating a dissipation of the driving energy and the possibility that large volumes of oil will remain unrecovered in the reservoirs. The studies reported in this paper were undertaken to develop laboratory data of the type most likely to be needed by persons studying the susceptibility of the Newcastle sand reservoir to secondary-recovery methods.]

Jan 1, 1957