Search Documents

By I. M. Gordon, J. Blackshaw

"Run-of-mine ore is reduced to 4 per cent on 4 mesh (3/ 16 inch), using four stages of dry crushing. The mill feed is then reduced to 2 per cent on 48 mesh and 60 per cent through 200 mesh, using one stage of ball milling in cyanide solution. During the subsequent treatment about one-tenth of the tonnage is removed as a table concentrate and ground to 77 per cent through 325 mesh. The size of the mill tailing is 66 per cent through 200 mesh.Four stages of ore reduction began when the dry crushing plant at No. 26 Shaft came into operation at a maximum rate of 440 tons an hour on July 31, 1941. A detailed description of the crushing plant was published in C .I .M. Trans., Vol. LVI, 1953.One-stage ball milling in cyanide solution came into full operation on January 11, 1938. The ball milling plant had a capacity of 4800 tons daily when reducing mill feed at 2. 7 per cent on 1/ 4 inch to 54. 3 per cent through 200 mesh. Primary grinding to 60 per cent through 200 mesh commenced May 22, 1945, when the feed was 3 per cent on 4 mesh. Under these conditions the capacity of the ball milling plant is estimated at 4300 tons daily. A description of the 11 Hollinger Crushing and Grinding Plant"" by D. C. McLaren was published in the Canadian Mining Journal, June 1944.The concentrate grinding circuit using a 7 x 15 low discharge ball mill and a 19-foot diameter bowl classifier with a 6-inch centrifugal pump to close the circuit began operating in the ball milling plant on October 24, 1939."

Jan 1, 1965

By Walter Kahn

Increasing consideration is being given to simplifying traditional methods of tracing pipelines and maintaining required temperatures of stored fluids. Because of their reduction in capital costs, virtual elimination of maintenance. ease of control and "cleanliness"; interest in electrical techniques has accelerated. 1,2 Resistance cable and other heaters have been given some attention. but less well known in the recent introduction of thermal conductive coatings. This paper is addressed to the use of thermal conductive coatings for heating fluid-transport piping and storage tanks. Emphasis will be given to the simplicity, efficiency, and versatility of design and application which their unique properties further contribute to the general economics of electrical heating.

Jan 1, 1965

By John W. Thatcher

A demountable X-ray tube vacuum spectrograph was designed by the Bureau of Mines for the determination of long-wavelength X-ray spectra from the light elements. This instrument was operated for both secondary and combined primary-secondary excitation of the aluminum K-series. There was an increased analytical sensitivity for elements in period 3, and an indication that with improved X-ray tubes or direct election excitation of the sample, X-ray determination of elements in period 2 is also possible.

Jan 1, 1965

By M. N. Shetty

LARGE copper whiskers (-100 p) of 11111 orientation were tested in a floor-model Instron testing machine, at liquid nitrogen temperature. (Testing methods will appear elsewhere.) Whiskers deformed by twinning after some initial deformation. A load-elongation curve at the onset of twinning is reproduced in Fig. 1. Twinning was confirmed by taking a back-reflection Laue picture, using a slit colli-mator, which showed distinct splitting of reflections. The tensile stress reached just before twinning is about 1.4 x 107 g per sq cm (-7.0 x106 g per sq cm—resolved shear stress) which drops to 1.2 x107 g per sq cm (-6 x 106 g per sq cm—resolved). This twinning stress is about five to ten times larger than the value for bulk single crystals of copper deformed at 77°K (-106 g per sq cm—resolved). Twinning models based on Cottrell-Bilby's pole mechanism are discussed in detail by Venables.' In the present work a mechanism based on the idea of failure of a Lomer-Cottrell barrier by recombination will be proposed. An L-C barrier may fail either by recombination or by dissociation.3 Fig. 2 provides the necessary information. It shows that the stress necessary to break such a barrier is about 1.8 x 107 g per sq cm by recombination and 4 x 107 g per sq cm by dissociation at 77°K. The twinning stress reached by whiskers is comparable to the stress level required for failure of an L-C barrier by recombination. (Stroh himself points out that his calculations should not be taken too literally.) We consider a segment of the L-C dislocation which has recombined (AB in Fig. 3) over a length to form the total dislocation which then glides in the

Jan 1, 1965

By James F. Neill, O&apos

Brown iron ore resources in Barbour, Butler, Crenshaw, and Pike Counties were investigated in a drilling program and geological study by the Federal Bureau of Mines in cooperation with the Alabama Geological Survey and the University of Alabama. The aggregate footage drilled was 18,010 linear feet. When developed, reserves of 12,664,000 long tons of crude ore were indicated, containing from 26.9 to 29.0 percent iron and 0.2 to 1.6 percent manganese under a maximum overburden of 40 feet. Total inferred crude ore for the four counties was calculated to be 827,700,000 long tons. Beneficiation of samples by simulated log washing and use of a 1/8-inch screen yielded from 46.8 to 51.7 percent iron and 0.2 to 2.6 percent manganese. Screen-test studies indicated no appreciable interlocking between the iron and manganese minerals and the waste particles of materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size. While an indicated 2,198,000 dry long tons of usable iron ore can be recovered, sink-and-float tests show that it may be possible for 4,654,000 dry long tons to be recovered by other than log washing. However, applicable commercial processes have not been demonstrated.

Jan 1, 1965

By Stephen Utter

Stresses induced by block-caving mining were estimated from in-place measurements of strain or deformation in rock and concrete around mine openings. The four types of gages used for measurements in the Climax Molybdenum mine during 1959-61 were Whittemore gage, Carlson strain meter,2 Valore strain cell, and Climax extensometer. Gage performance in the laboratory was evaluated by stressing instrumented rock and concrete specimens in a universal testing machine and by comparing measurements taken by the gages and a standard gage. Gage performance in the mine was evaluated by comparing measurements taken during an 18-month test. The Whittemore gage, Carlson strain meter, and the Climax extensometer proved suitable for the investigation; the Valore strain cell, effective in the laboratory tests, gave erratic measurements in the mine.

Jan 1, 1965

By Luis F. Morán

El presente texto señala algunos aspectos que comprende el proyecto de San Nicolás desarrollado por Marcona Mining Company. El proyecto señala las facilidades de la mina, transporte, almacenamiento del mineral, plantas chancadoras, lavado y concentración por medio denso, concentración magnética, instalaciones para almacenar productos comerciales, formación de pellets verdes, endurecimiento, terminado y control del proceso.

Jan 1, 1965

By J. W. Jensen

EXTENSIVE research and development was performed on the manganese-copper vibration-damping alloys to determine the relationship between the properties of the alloys and variations in composition, fabrication, Mid heat treatment. Mn-Cu alloys with unusually high specific damping capacity, 20 to 25 percent at a stress of 5,000 psi, have also the following useful properties: Tensile strength, 90,000 to 110,000 psi; yield strong, 60,000 to psi; elongation, 20 to 25 percent; hardness, 90 Rockwell B; and fatigue limit at, 28,000 to 30,000 psi. Both standard and special methods of testing were employed to obtain data on strength, modulus, hardness, resistivity, dilatation, micro-structure, crystal lattice, and damping capacity. The extensive tabular and graphical data on these properties are presented for alloys containing 50 to 85 percent as quenched d solution) and after various aging treatments. Expansion coefficients for all Mn-Cu solid solutions are graphed and a dilatometer study of contraction during aging is reported. Although high damping capacity is associated with aging to precipitate a-Mn from solid solution, with a cubic-tetragonal transformation and with the occurrence of antiferromagnetic ordering in Mn-Cu alloys, a tenable theory of the damping mechanism has not been reached.

Jan 1, 1965

By M. Copeland

Phase relations of gadolinium alloyed, up to 40 weight-percent (wt pct), with AISI 304-type stainless steel were established. Body-and face-centered cubic iron-rich solid solution phases and several intermetallic gadolinium-containing compounds of variable composition that approximated the formulas Fe9Gd, Ni7Gd2, Ni3Gd, Fe2Gd, NiGd, and NiGd3 were identified. The intermetallic phases Fe9Gd and Ni7Gd2 were noted to melt at about 1,080° C at about 0 to 2 wt pct gadolinium. The melting temperature of Fe9Gd increased with increas-ing gadolinium content to a plateau at about 1,230°C and 30 wt pct gadolinium, and the melting point of Ni7Gd2 decreased to a plateau at 900° C and 30 wt pct gadolinium where Ni3Gd, NiGd, and Fe2Gd coexist. Body-centered cubic iron solid solution was stable from 1 to 2 wt pct gadolinium to higher contents, 30 wt pct gadolinium or possibly more, and face-centered cubic iron up to 12 wt pct gadolinium below 1,200° C. The stability of these phases above 1,200° C was not resolved except for the mel points. A limited number of fabrication variables as well as mechanical and corrosion properties of alloys containing up to 5 wt pct gadolinium were studied. Equilibrating and forming operations were best conducted at about 940° to 1,080° C. Some variability in the yield and tensile strengths of alloys was noted; however, there was a continual decrease in ductility and impact resistance with increasing gadolinium contents. The resistance of gadolinium alloys to corrosion in water at 354° C was about the same as stainless steel.

Jan 1, 1965

By Ernest Hucke

This paper will cover basic pneumatic and electronic sensors, transducers, transmitters and their application in the Mining Industry.

Jan 1, 1965

By John Convey

This paper, a follow-up to an earlier study, gives the history of Canadian developments in mineral processing from 1921 to the fall of 1964. It deals extensively with comminution and flotation, and then goes on to cover the fields of gravity concentration, magnetic concentration, cyanidation, the processing of uranium ores, and instrumentation. Several outstanding examples of installations are given. The paper concludes with a discussion of present-day trends in mineral processing. Introduction T HE history of the developments in mineral processing in Canada from its earliest times to 1920 has already been published by one of the authors (1). The present paper is thus a logical follow-up to bring this history to date. From 1834 to 1920, mineral processing in Canada, as elsewhere in the world, was in its formative stage. This, however, prepared the ground for developments that have resulted in a mining empire from the Atlantic to the Pacific, a mining empire which could be said to be almost on par with that in the United States.

Jan 1, 1965

By Waugh D. M

investigations have been undertaken into the flow characteristics of mineral slurries from a number of Australian metallurgical plants including Mount Isa Mines Ltd., North Broken Hill Ltd., and Broken Hill South Ltd. Experimental equipment installed for this work included facilities for continuous recording of flow rate and pressure drop and detection of sedimentation.Although the method has subsequently been described in published literature, it is believed that the investigations included the original application of a method for correlation of the flow rate and pressure drop data. This method depends on solving by graphical methods the values of the constants k, and c in the relationship EQUATION 1 where D is pipe diameter; ?P, pressure drop; L, length; and V, mean linear velocity. Discussion of this correlation also reveals why sedimentation velocity does not necessarily vary greatly with pipe diameter.INTRODUCTIONIn order to design pumps and pipeline installations for a Newtonian fluid, measurements of the fluid's density and viscosity in any of a number of instruments are sufficient. Substitution of these values in well known equations to calculate Reynolds numbers and subsequent correlation to determine friction factors are all that is required for engineering specification.As a result of work during the last decade, particularly that of Metzner and Reed (1955) and Dodge and Metzner (1959), it is now possible to design for homogeneous non-Newtonian fluids using relatively simple instrumental measurements.These methods can sometimes be applied to thick slurries which behave as if homogeneous. However, for the...

Jan 1, 1965

By Jack G. Crump

Nuclear radiation systems for gauging solids content in process slurries and level in crushers has demonstrated acceptance in ore processing. The use of nuclear radiation for moisture analysis of bulk materials is presently receiving acceptance in beneficiating and agglomerating processes. On the horizon is the use of nuclear activation methods for continuous, qualatative and quantitative analysis of concentrate. The common characteristics of these uses of radiation is the non-contacting nature of the measurement. Unquestionably, this is the dominant reason for acceptance of nuclear methods in level and slurry-gauging. Moisture activation analysis of a product using nuclear methods retain this advantage. However, and: more importantly, they offer new solutions to old problems. The nuclear method in addition to being non-contacting, is non-destructive and provides a continuous measurement of the process variable. The system responds: to the fundamental makeup of matter, mass and elemental composition, not to secondary properties such as temperature, resistivity, or dielectric constant. Measurement is a volume rather than a surface phenomenon, thus the results can provide a truer pricture of the measured variable.

Jan 1, 1965

By Jr. Smith

The equilibrium compositions of product gases for mixtures of air with methane, propane, or ethylene at and around flame temperatures are reported. For each hydrocarbon, compositions are given for five fuel-to-air ratios--two lean, two rich, and one stoichiometric--at five pressures, from 1 to 20 atmospheres, and at an ambient temperature of 25° C.

Jan 1, 1965

By W C. Shakespeare

The Ontario Committee on Taxation is making a comprehensive study of taxation in the Province of Ontario, and in this connection has received representations concerning mining taxation from a number of interested parties. Some of the more important recommendations on mining taxation are reviewed in this article. Introduction FOLLOWING the appointment of the Federal Royal Commission on Taxation, the Ontario Government, effective in November, 1962, appointed the Ontario Committee on Taxation to review taxes and revenues available to the Province of Ontario and its local governments, to co-operate with the Royal Commission on Taxation and with any other bodies of enquiry appointed by other provincial governments, and to make such recommendations as it sees fit to the Prime Minister of Ontario and the Executive Council. The members of the Committee are: MR. L. J. SMITH, F.C.A., Toronto, (Chairman) MR. ERIC HARDY, Toronto DR. R. CRAIG MCIVOR, F.R.S.C., Hamilton MR. CARL A. POLLOCK, Kitchener MR. R. BREDIN STAPELLS, Q.C., and Toronto. Like its Federal counterpart, the Royal Commission on Taxation, the Ontario Committee has held public hearings, has received written

Jan 1, 1965

By L. F. Heising

The Bureau of Mines evaluated 191 composites from the central Mesabi Range, Minn., chiefly by reductive roasting and magnetic separation. After reductive roasting and magnetic separation at minus 325 mesh, 28 composites produced concentrates that contained an average of 66.0 percent iron with less than 10 percent silica. Recovery of contained iron was over 90 percent. Natural magnetic material in excess of 5 percent was present in 142 composites. Trial flotation tests were used to evaluate three samples unresponsive to reductive roasting and magnetic separation procedures, and satisfactory concentrates having low silica contents (averaging 6.6 percent) were achieved.

Jan 1, 1965

By C. F. Giermak

Over a considerable period of time great interest has been shown in selective dry concentration of fine ferromagnetic particles, although it is only recently that new permanent magnetic materials have been made available to permit building of such permanent magnetic separators. It is well known that the conventional drum separator does' not efficiently separate fine materials. The centrifugal force on any drum acts in accordance with the particle size and gravity, which may beat varying magnitude-.opposite to the magnetic force, especially when the material is not closely sized. The Magnetic-Mechanical Separator (MMS) is designed for the concentration of fine, unsized magnetic materials where the percentage composition of magnetics to nonmagnetics, or the nature and texture of the materials, is such that its unique agitation and shake-out action with no centrifugal force provides greater efficiency than is obtainable by conventional magnetic separation equipment. This machine consists of a complete double belt conveyor unit with a premagnetizing Axial Pole Agitating Pulley at the feeding end of the lower conveyor belt and a special agitating concentrator magnet above the lower belt of the upper conveyor.

Jan 1, 1965

By Warren E. Morrison

Stimulated by 4 years of continuous economic growth without inflation, demand for energy in the United States reached an alltime high in 1964. Total value of production of goods and services (gross national product--GNP) for the year was $629 billion, an increase of 6.8 percent from 1963. Allowing for price changes based on 1958 dollars, the gain in real terms was 5 percent. In 1964 the Federal Reserve Board Index of Industrial Production stood at 132, a rise of 6.2 percent. With the impetus provided by personal income and corporate tax reductions during the year, aggregate wages, profits, and consumption reached record levels. Even the persistent balance of payments problem improved. Against this background the national consumption of commercial energy increased 4.2 percent. Energy needs continued to be met largely from domestic resources with imports, mainly crude petroleum and refined petroleum products, accounting for but 7 percent of the total. Mineral energy resources, namely gas, coal, and petroleum, contributed 96 percent of the input of energy into the economy during the year. The remaining 4 percent came from hydropower and nuclear power.

Jan 1, 1965

By James F. Devine

This Bureau of Mines report describes tests conducted at three sites to determine if, and to what extent, a vertical presplit fracture plane placed between a blast point and detection point will reduce vibration levels. Statistical analyses indicate that the presplit fracture plane did not reduce the vibration level.

Jan 1, 1965

By John Brownson

Ge-Si N-N heterodiodes hare been built recently which show promise as high-speed logic devices. Low-resistivity germanium is deposited on silicon substrates held at temperatures above the germanium melting point and an alloyed heterojunction formed. The diodes are fabricated from this material using conventional mesa techniques. Over-all device qualify has been greatly improved by the use of epitaxial silicon substrates, that is, a subsirale consisting of a film of thin, high -resistivity silicon on a thicker Piece of low-resistirily silicon crystal. A semimpirical device design equation has been devised which predicts switching performance fairly well within the range of resistivitics and geometries employed. Switching times 01 0.9 ns and PIV 's of —20 v are typical of the better 10-ma diodes. Switching times as low as 0.5 ns have been observed for 10-ma diodes and as low as 2.8 ns for 200-ma diodes. With further development it should be possible to improve switching speed by a factor of four. IN our laboratory, Ge-Si heterodiodes have been built recently which show promise as high-speed logic devices. The diodes have been built using a process reported in some detail in an earlier publication.' The process in short involves alloying a thin film of low-resistivity germanium into a silicon substrate. the germanium having been transported and deposited by the well-known Theuerer halide reduction process.2 This process contrasts with that reported earlier by Oldham who used an essentially conventional direct epitaxial deposition technique.3 Oldham's process, unlike ours, requires cleavage of the silicon sample inside the reactor furnace the instant prior to deposition. Our process has the advantage of yielding large-area macro-scopically plane heterojunctions. Heterodiodes in general have several interesting properties. Without attempting to summarize the theory of heterojunctions.4 two of these properties which have direct relevance should be mentioned. First, N-.V and P-P heterojunction diodes rectify alternating current. Provided that either the band gap or the electron affinity of the two materials is different (which in general is the case), electronic barriers will exist in the junction band structure. When the device is sufficiently forward-biased, the barriers shift so as to permit current flow, and when it is reverse-biased. the barriers block current flow. Second, for N-N and P-P heterodiodes. the foward-conduction process involves majority carriers only. Consequently. when such a device is turned off. there is no minority-carrier storage and hence the diodes switch on and off quite rapidly. As we have reported earlier. N-P and N-N Ge-Si heterodiodes have been built in this laboratory. As one would predict from theory, the N-P heterodiodes were rather slow in turning off while the N-N's were quite fast. Similarly, the turn-off time of the N-P's increased rapidly with forward current while that of the N-N's was independent of forward current. Both N-N's and N-P's were moderately photosensitive. Photocurrents resulting from normal room illumination were as high as 1 µa at 1 v for small-area devices. The most disappointing parameter of the early N-N devices was reverse leakage.' The reverse characteristic was invariably "soft" and leakage at only several volts reverse bias was intolerable. The reverse characteristic was greatly improved by using higher-resistivity silicon substrates. Leakage becomes large at voltages about one third of the avalanche voltage one would expect of a P-N homo-junction formed on silicon of the same resistivity. Thus leakage could be reduced to reasonable limits by using unconventionally high-resistivity silicon. Medium-power diodes formed on 30 ohm-cm substrates leaked typically 15 to 50 µa at 100 v reverse bias. The use of high-resistivity silicon substrate material, however, created a new problem. In order to have an acceptable forward-conductance characteristic. the area of the diodes had to be increased. With this increase in area, the capacitance increased. Switching time for N-N heterodiodes is essentially a linear function of capacitance. Thus when the resistivity was raised. so was the switching time. A SEMIEMPIRICAL HETERODIODE DESIGN EQUATION As a result of our experiments with a limited range of diode geometries and resistivities. a semi-

Jan 1, 1965