Search Documents

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

By A. O. Gapchich, T. N. Matveeva, N. K. Gromova

"Tin sulfide ores and aged man-made products obtained after their processing are distinguished by a complex material composition and uneven impregnation of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin ore (cassiterite). Enrichment of such ores is performed through sophisticated multistage schemes using not only gravitational methods, but also gravity flotation, flotation, magnetic separation techniques. Tin ores also contain rare and precious metals (indium, scandium, silver), characterized by fine dispersity and microscale to nanoscale fineness of mineral formations. During flotation concentration these metals are extracted along with the main ore minerals into concentrates (tin, copper, tungsten, etc.), however, up to 10-20 % of them are lost with final tailings. The aim of the work is an experimental study of the modification of the surface of sulfide minerals and cassiterite by stable metal-collector complexes to increase extraction of fine tin, silver, copper and other metals from complex tin ores. Triamide cyanuric acid (TCA) was studied as a thin silver flotation modifier. Thermophilic polymer with a functional group of phenylphosphine TMPPh was used as a selective flocculant. For experimental studies of the physical and chemical effects of collecting agents on the surface of minerals the following analytical techniques were used - the analytical scanning electron emission ASEM (LEO 1420VP INCA OXFORD ENERGY 350) and laser (KEYENCE VK-9700) microscopy, measurements of electrode potentials of mineral anthills by potentiometric titration, monomineral and pulp flotation. New data on formation of the adsorbed layer of DBDTC on the surface of chalcopyrite, galena and arsenopyrite were obtained, and the dimensions of the reagent films and the strength of their adsorption. The indiscriminateness of cassiterite to DBDTC ensures its selective separation into a chamber product during the flotation of sulfides. It is shown, that modification of the sulfide surface by stable complexes Me-DBDTC and Ag-TCA-TMPPh will increase the recovery of non-ferrous metals and silver into a collective sulfide concentrate and will provide a high-quality tin concentrate for flotation of tin sulfide ores.The studies were perfomed with the aid of the Russian Science Foundation (Project No. 17-17-01292).INTRODUCTIONTin sulfide ores and aged man-made products obtained after their processing are distinguished by a complex material composition and uneven impregnation of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin ore (cassiterite). Enrichment of such ores is performed through sophisticated multistage schemes using not only gravitational methods, but also gravity flotation, flotation, magnetic separation techniques. Tin ores also contain rare and precious metals (indium, scandium, silver), characterized by fine dispersity and microscale to nanoscale fineness of mineral formations. During flotation concentration these metals are extracted along with the main ore minerals into concentrates (tin, copper, tungsten, etc.), however, up to 10-20 % of them are lost with final tailings. In this regard, it seems advisable to use new varieties of flotation reagents in order to increase extraction of finely dispersed tin, silver, copper and other non-ferrous and precious metals from multi-metal tin ores (Bocharov and Ignatkina, 2007; Khanchuk etal., 2012; Wu and Zhu, 2006; Yusupov etal., 2016)."

Jan 1, 2018

By J. M. Ortiz, J. Haas, W. Kracht, G. Pamparana

This work explores the effect of ore hardness variability on the design of a solar photovoltaic system with battery storage and grid backup, to operate a semi-autogenous grinding mill (SAG). First, a case of two synthetic ore populations was studied, without any consideration of spatial distribution. The mean and variance of the ore hardness (measured in specific energy consumption, SEC) of both populations were subjected to a sensitivity analysis. The operation was evaluated with one and two stockpiles. The latter allows classifying according to ore hardness as a way to adapt the SAG energy consumption to the solar cycle. The results show that using two stockpiles allows achieving a larger autonomy (i.e. less energy imports) at lower total costs, especially when the difference of mean hardness between the two populations is large. The difference in variance (between the two populations) has a smaller impact on the design recommendations. Second, a case study was performed considering the spatial distribution of geometallurgical units. Two cases were considered: (a) brownfield, when there is historical information of the actual variability of the ore hardness; and (b) greenfield, when the system design relies mainly on geometallurgical modeling. Brownfield and greenfield planning result in similar sizing recommendations of the solar power plant, if precise drill cores are available. In this case, geometallurgical modeling is an effective tool for forecasting the energy demand necessary for designing the power plant.

Jan 1, 2018

By E. G. Ozhogina, O. B. Kotova

"The ores of black, non-ferrous, rare, noble metals are mostly distinguished by a variety of mineral types and complexity of their material composition. This article is devoted to the promotion of the concept of mineral processing in modern realities of the deficit of high–grade ores and increase in their demand. Normative and methodical documentation for specific types analysis with the definition of the field of application are presented in this paper. . For example, the pyrochlore-monazite-goethite ores from one of the deposits from Eastern Siberia - Chuktukonskoe ore field were tested. The development of mineralogical methods and testing of specific raw materials are shown. The method of small-angle X-ray (and also synchrotron) scattering, which was developed for solving problems associated with structural high-resolution diagnostics, was tested for bauxites of Vezhay-Vorykvinskoye field.INTRODUCTION A highly intense production of many types of mineral deposits results in gradual depletion and of mining-geological and mining-technical conditions of various ore reserves ?. Relatively easily accessible and rich deposits are getting depleted in the first place, and it is necessary to involve low grade and refractory ores into production and processing. Traditional technologies can hardly be applied (Chanturia, 2017; Bazin et al., 2014; Ponaryadov, 2017). The urgency of development of the concept of technological mineralogy focuses on the confirmation of new methods and approaches to the development of mineral deposits, creation of scientific and methodological pre-requisites for solving the problem of rational development of mineral deposits, maximum extraction and integrated application of all minerals (both principal and associated), expansion and strengthening of mineral and ores.The article is aimed at updating tasks that should be addressed within the applied mineralogical research: – forecast of quality of ore at early stages of exploration and technological indicators for the redistribution of properties ore, – interactive monitoring of these indicators by mineralogical and analytical methods;"

Jan 1, 2018

By Juan J. Monsalve, Nino Ripepi, Richard Bishop, Jon Baggett

"Terrestrial laser scanning (TLS) is a useful technology for rock mass characterization. A laser scanner produces a massive point cloud of a scanned area, such as an exposed rock surface in an underground tunnel, with millimeter precision. The density of the point cloud depends on several parameters from both the TLS operational conditions and the specifications of the project, such as the resolution and the quality of the laser scan, the section of the tunnel, the distance between scanning stations, and the purpose of the scans. One purpose of the scan can be to characterize the rock mass and statistically analyze the discontinuities that compose it for further discontinuous modeling. In these instances, additional data processing and a detailed analysis should be performed on the point cloud to extract the parameters to define a discrete fracture network (DFN) for each discontinuity set. I-Site Studio is a point cloud processing software that allows users to edit and process laser scans. This software contains a set of geotechnical analysis tools that assist engineers during the structural mapping process, allowing for greater and more representative data regarding the structural information of the rock mass, which may be used for generating DFNs. This paper presents the procedures used during a laser scan for characterizing discontinuities in an underground limestone mine and the results of the scan as applied to the generation of DFNs for further discontinuous modeling.INTRODUCTIONAccording to the Mine Health and Safety Administration (MSHA), between 2006 and 2016, the underground stone mining industry had the highest fatality rate in 4 out of 10 years, compared to any other kind of mining (MSHA, 2016). Additionally, during that same time, 40% of the fatalities were due to ground control issues, such as roof and rib collapses and pillar bursts. The National Institute for Occupational Safety and Health (NIOSH) developed guidelines for designing underground stone mines (Esterhuizen, Dolinar, Ellenberger, and Prosser, 2011). However, these guidelines do not apply to all underground stone mines.Monsalve, Baggett, Bishop, and Ripepi (2018) present a case study of an underground limestone mine experiencing a structurally controlled mode of failure. The authors analyze different methods to study that type of instability. They conclude that the integration of terrestrial laser scanning (TLS) with discrete element modelling (DEM) can be used to prevent rock falls in underground excavations to enhance worker safety. However, an adequate rock mass characterization and structural mapping must be performed in order to generate reliable models that allow the engineer to have a better understanding of the rock mass behavior."

Jan 1, 2018

By Patrick O. Shires, Harry W. Schnabel

With stable building sites becoming scarce in the greater San Francisco Bay Area, the new Summit Senior Care Facility is being built into the side of an unstable hillside adjacent to the San Ramon Regional Medical Center in San Ramon, California. This hillside has had a long history of instability and the site of the new Senior Care Facility required excavation into both a historic old landslide and a more recent active landslide. After a thorough geotechnical study, it was concluded that the best way to build the new facility would be to construct a tied-back retaining wall in the area of the old landslide, since it extended off-site onto two adjacent properties, and remove the active landslide and replace it with compacted fill before cutting into its toe area with an additional tied-back retaining wall. The design was further complicated by the proximity of the site to several active faults. In the area of the old landslide, the combination of an ascending slope behind the wall, landslide forces and seismic forces resulted in total design pressures between 365 to 4,575 PSF for a wall with a maximum height of 30 feet. The wall for the old landslide was constructed by first drilling and placing steel soldier piles in concrete. The tip of the soldier piles extended a minimum of 12 feet below the landslide plane that was up to 36 feet below the bottom of the wall. Permanent double corrosion protected tiebacks were then installed through the soldier beams and anchored below the slide plane. A shotcrete facing was then installed on the face of the wall. BACKGROUND The site of the Summit Senior Care Facility is located on the southwest flank of Mount Diablo adjacent to San Ramon Valley which is characterized by gently rolling hills. The San Ramon Valley Regional Medical Center, which opened in 1990, is located to the north and an existing church is located to the southwest. There are also private residences located to the southeast. The site is shown in Figure 1. Numerous faults run close to the site, the most significant of which are the Calaveras and Pleasanton faults. The site has also had a long history of slope instability and has been the subject of numerous investigations. Studies conducted in 1979 and 1984 concluded that there was a landslide in the area and recommended that a buttress shear key be constructed between the subject site and the existing church for a sewer main as well as removal and replacement of the head area of the old landslide to stabilize the hospital site. While two previous geotechnical studies in 2008 and 2016 identified slope instability, they did not recognize the genesis and limits of the old landslide on the western portion of the site or the limits of the active landslide on the eastern portion of the site.

Jan 1, 2018

By Rick Deschamps, Brian Barkauskas, Aled Hughes, Abigail Stein

In central Washington, six miles south of the small town of Vantage, the flow of the Columbia River is harnessed by the Wanapum Dam which is part of the Priest Rapids Hydroelectric Project owned and operated by Grant County Public Utility District (GCPUD). Extending more than 8,300-feet from bank to bank, the dam includes left and right earth embankments, left and right concrete gravity sections and a 10-unit powerhouse. Adjacent to the right embankment is a concrete gravity spillway featuring radial gates measuring 50-feet-wide and nearly 70-feet-high. In the early 1960’s when Wanapum Dam was built, these seven-story spillway gates were the highest in the world. In late February 2014, 50-years into its service life, during a routine maintenance inspection, observant workers noticed a slight misalignment in the roadway deck curbs and handrails located on top of the spillway. Further survey and inspection efforts uncovered a 65-foot-long by two- inch-wide crack that spanned the full length of Monolith 4. On discovering the extent of the damage, GCPUD initiated immediate drawdown of the reservoir to relieve pressure on the spillway monoliths. Wanapum Reservoir and the areas directly downstream of the dam were immediately closed, boat ramps and inlets were left completely dry, campsites were closed and boating activity was banned on the lake until further investigations and remedial procedures were in place and completed. An extensive root cause analysis ultimately led to the conclusion that errors in the initial design calculations and late changes to the final spillway design led to a condition that generated tensile stresses in the concrete at the upstream face, which over a period of 50-years resulted in the formation of a crack along a horizontal lift joint located about 85-feet below normal pool elevation. Further analysis showed that, although visible distress was found at Monolith 4, there was nothing preventing this issue from happening at other locations along the dam spillway. Although no visible cracking was found in the other monoliths, repair procedures for Monolith 4 would have to be replicated at the remaining monoliths.

Jan 1, 2018

By Braden Lusk, Tristan Worsey, Nathan Rouse, Kyle Hall

Loading explosives up hole has challenges that are typically not seen in down hole explosive loading. Most explosives applications are not up hole. Lack of experience and technology can cause significant problems when loading explosives up hole. When results aren’t achieved, the blame is commonly put on the design when the true problems are unknown. Not knowing the cause of the problem causes drill and blast designs to be over engineered and very costly with little success. Being able to know and record key data is crucial to actually solving the problem. This paper goes over blast instrumentation that can be used to trouble shoot drill and blast problems in up hole explosives loading in underground mines. The tools and procedures used to trouble shoot include velocity of detonation recorder, borehole tracking, seismographs, and borehole camera. Each item will be discussed in detail with a case study to show the usefulness of the instrumentation. The operation discussed in the case study had issues pulling raises and had hang ups in the stope shots. These problems caused production slowdowns and costly remediation blasting that was not very successful. The case study is an underground gold mine that used modified sub-level caving with backfill as the mining method.

Jan 1, 2018

By H. Yoshida, H. Hatta, T. Suzuki

"The effect of the copper and magnesium contents and quenching rate during quenching on the age hardening behavior of 2000 series aluminum alloys was investigated. For the higher copper-containing specimens as conventional alloys, like AA2024, precipitation of the stable phases increased as the quenching rate decreased under the as-quenched conditions. The maximum hardness after the artificial aging of air cooled(AC) specimens was much lower than that of the water quenched(WQ)specimens. On the other hand, for the lower copper-containing specimens, coarse precipitation did not increase even in the case of the AC. The age hardening behaviors of the WQ and AC were very similar such that the maximum hardness and aging rate were almost the same. Many parts of the fine precipitates that increased the hardness were thought to be the GPB zone or fine S’ phase for the WQ and relatively coarse S’ phase for the AC. From the calculated CCT(continuous cooling transformation)diagrams, the lower copper-containing specimens could maintain the copper and magnesium in the solid solution state during the AC, so they could be quenched at a rather slower quenching rate like the AC.INTRODUCTIONThe 2000 series aluminum alloys, containing copper and magnesium as the major chemical components, are some of the well-known heat treatable aluminum alloys. These alloys have a high quenching sensitivity, thus the age hardening ability of these alloys decreases with as low quenching rate. To prevent the decrease of the age hardening ability, quenching is done by a method such as water quenching, which is not very efficient in an industrial situation, because the method requires such large equipment. For these alloys, reducing the quenching sensitivity helps them to be produced in a rather convenient way. For example, 6000 series alloys such as A6063 have low quenching sensitivity, thus they could be quenched by only air cooling just after extrusion and they do not need water quenching. Based on these reasons, investigations of these alloys with high copper and magnesium contents have been conducted in the past to find a way to lower the quenching sensitivity by adding transition elements such as manganese, chromium and zirconium (Kanno, Suzuki, & Itoh, 1986; Suzuki & Itoh, 1986; Kanno, Sakuma, Muromachi, & Watanabe, 1988). However, very few studies have focused on the quenching sensitivity of the lower copper and magnesium containing alloys because of their usage for structural components with high strength, and most of the past studies have used only the fast quenching method like water quenching. On the other hand, from our recent results, there is a possibility to lower the quenching sensitivity of 2000 series alloys with lower alloying elements. In this paper, the effect of the copper and magnesium contents with lower alloying elements and quenching rate, especially in case of slower quenching rate than conventional quenching method, on the age hardening behavior of the 2000 series alloys is investigated by the hardness measurement, structure observation and thermal analysis."

Jan 1, 2018

By Y. Y. Li, T. T. Yang, R. X. Zhou, Z. H. Shen

"Wetting theory is one of the basic theories of flotation. The effects of concentrations, carbon chain length and pH values of saturated fatty acid collectors (lauric acid, myristic acid, palmitic acid and stearic acid) on the surface wettability of collophanite and dolomite were investigated by measuring the contact angle with dynamic captive-bubble technique and calculating adhesion work of bubble-mineral. The results show that the contact angles both of collophanite and dolomite are higher with enhancement of hydrophobicity when pH value of 5~9. The contact angles both of collophanite and dolomite are reduced with improvement of surface hydrophilicity. When strong acid pH value of 2~4 or strong alkaline pH value of 10~13. The reasons for this are that the fatty acids mainly exist with insoluble RCOOH molecules in strong acid condition, and competitive adsorption of OH- and RCOO- in the mineral surface is formed in strong alkaline condition. With the increase of the collector concentration, the contact angles of the collophanite and the dolomite all first increase then decrease. The formation of hydrophilic micelles results in the decreasing of contact angles and enhancement of surface hydrophilicity opposite when the collector concentration exceeds CMC. The contact angles of the collophanite and dolomite and the WSG of the bubble adhesion increase, the hydrophobicity enhance with the increasing of carbon chains of saturated fatty acid from 12 to 18. The variation tendency for the adsorption quantity of collectors and floatability of collophanite and dolomite are in line with the change trend of contact angle basically. It shows that the wettability of solid-liquid-gas interface can be well characterized by the dynamic captive-bubble technique.INTRODUCTIONPhosphorite resources are the main raw material for producing phosphate fertilizer and producing phosphoric acid (Cao et al.,2005), which is an important strategic mineral resource. The useful minerals in calcareous-magnesium phosphate ore are collophanite, and the main gangue minerals are dolomite (SISH et al.,2003). The lattice ions of the phosphorite and dolomite are both Ca2+, their similar surface properties and similar floatability are the main reason for the flotation of calcareous-magnesium phosphate ore difficultly (Fang et al.,2011). Usually, fatty acid collectors are used for the flotation of calcareous-magnesium phosphate ore under acidic conditions by reversing flotation method to remove dolomite (ABOUZEID et al.,2009), or direct flotation is used to gather collophanite in the alkaline conditions (Gong et al.,2017). The flotation behavior of collophanite and dolomite affects the indexes of concentrate and flotation efficiency directly. Therefore, it is necessary to study the action mechanism and the flotation method of the collector with the phosphate rock and dolomite respectively (Moudgil et al.,1988; Hanna, et al.,1990)."

Jan 1, 2018

By Jun Xiao, Jianwen Yang, Yanhong Dong, Daixiong Chen

"MANGOTE Surface oxidizied mine is a gold-bearing deposit in Congo's Mai-Ndombe Province. In the past decades, the ore has been exploited in a crude way by local farmers, which directly causes the severe processing difficulty and lack of economy of cyanide leaching. Hunan Research Institute for Non-ferrous metals (HRIM) is currently investigating options to recover gold through understanding the mineralogical characteristics of MANGOTE surface oxidized ore. Chemical analysis , X-ray diffraction(XRD) and Quantitative Evaluation of Minerals by SCANing electron microscopy (QEMSCAN ) were conducted on samples from mine site. The bulk analysis results showed that gold separation of gold from gangue minerals was feasible after grinding the ore samples to 86.53% -74µm and adjusting the pulp specific weight at 100g/L, and gravity separation was conducted with using spiral chute after grading of fine particles. The research results highlight relationship between mineralogical characteristics of abandoned ore and economy of comprehensive utilization that might be directive experience to similar cases. INTRODUCTION The occurrence state of gold in natural gold minerals determines the basic recovery and recovery effect of gold(Komnitsas, C., & Pooley, F. D. 1989). The occurrence of gold in the ore refers to the form of gold in the ore.Generally the existing state of gold can be divided into four major categories according to the viewpoint of the dispersion system: independent minerals and gold, a coarse dispersed system;colloidal gold, a colloidal dispersion; solid solution gold, is atomic ion dispersion; adsorptive gold, according to the adsorbed particle is the micelle or ion, respectively is a colloidal dispersion or ion dispersion(Mao, S. D., & Yang, R. S. 2009; Liu, J. J. et al. 2007; Horisberger, M., & Rosset, J. 1977; Li, Y., & Audétat, A. 2013).With the increasing technology of comprehensive utilization of resources,varied plants can now process different gold ores with various occurrence states(Neesse, T. 2014; 7. Ogundare. et al.2014)."

Jan 1, 2018

By V. I. Ryaboy, I. V. Ryaboy, E. D. Shepeta

"The problem of separation of copper minerals and arsenopyrite remains relevant because of environmental requirements. The selective action of reagents with the thioamide group (thioamides) is known in iron sulfide’s flotation of pyrite and pyrrhotite. The aim of this study was to reduce the arsenic content in the copper concentrate when using thioamides by reducing the flotation of arsenopyrite in the flotation of the sulfide part of the skarn scheelite-sulfide ores. We have chosen the most widely used thioamides for the study, such as Z-200. We also synthesized new reagents with the thioamide group. The most selective and the most powerful thioamide copper collector were used for further studies. Reduction of arsenic content in copper concentrates is achieved in the following way: You need to apply a strong thioamide collector with a selective but weak dialkyldithiophosphate collector, or vice-versa, a selective, but a weak thioamide collector should be used with the dialkyldithiophosphate reagent with strong collective properties. The proposed combination presents industrial interest because of its accessibility. The application of thioamides in copper minerals and arsenopyrite selection has showed that these reagents have fewer selective properties than dialkyldithiophosphates. To achieve the comparable recovery of copper using dialkyldithiophosphates requires markedly greater consumption of thioamides, due to their lower hydrophobic ability. The application of a composition of thioamides and dialkyldithiophosphates allows to increase the recovery of copper and to obtain a lower arsenic content in copper concentrates compared to their individual use. The lowest arsenic content in the copper concentrate is obtained in the composition consisting of the newly synthesized thioamide with strong collective properties and selective dialkyldithiophosphate. The addition of even small amounts of xanthate to the composition of thioamides and dialkyldithiophosphates causes a sharp increase in the arsenic content in the copper concentrate without a notable increase in copper recovery."

Jan 1, 2018

By Jena Moshen

Underground Bulk Systems (UBS) technology has gained widespread application in tunneling and underground mining owing to its safety, reliability, increased Velocity of Detonation (VOD) and excellent results. However, its application in perimeter blasting is still limited and researchers are looking at ways of harnessing this technology for perimeter control. This simplifies the charging process by using one cost efficient product for charging both the perimeter and grid holes. This paper presents a case study on the application of underground bulk emulsion explosives for perimeter control blasting in underground room and pillar platinum mines. In order to achieve the required coupling ratios in the perimeter holes, the emulsion is loaded into specially formulated smaller diameter polyethylene (poly) pipes. The effectiveness of this method was evaluated using information obtained during routine blast audits and data supplied by the mines on half cast factors, over break and under break as well as analysis of data from Ground Penetrating Radar (GPR) Scans over a period of four years. This method of perimeter control, has given the platinum miners in Zimbabwe a competitive edge in cost effective perimeter charging and blasting by simplifying the previously costly deployment of traditional barrels and other decoupled cartridges. The method has been adopted by all the platinum mines in Zimbabwe as it has proven to be a cost effective alternative of controlling the perimeter walls, along with other key benefits that relate to safety, productivity and effectiveness.

Jan 1, 2018

By Qidong Zhang, Yongsheng Song, Wenjuan Li, Guiying Zhou, Kun Song

"Molybdenum is a very important rare mineral resources, which exists largely in oxidized ores and sulphide ores in nature. About 99% of metallic molybdenum comes from molybdenite. The talcose molybdenum resources are abundant but the resources utilization is low, because the talc is naturally hydrophobic and the floatability of talc is similar with molybdenite, which lead to difficult separation by flotation. Talc is easy entry into concentrate in flotation which can cause the content of MgO overhigh, therefore the molybdenum concentrate grade can not meet the industrial requirements. Thus the utilization level of talcose molybdenum resources has been restricted greatly.The adsorption of water on talc and molybdenite surfaces and natural floatability of minerals were studied by density functional theory method. The results showed that molybdenite and talc were layered minerals which exhibited similar surface wettability and H2O molecule prefers to stay with water rather than the minerals surfaces. N2 is adsorbed on talc and molybdenite surfaces more easily than H2O. The interaction and flotation behavior were studied by SEM and flotation experiments. The reason why talc interferes with the flotation molybdenite has been revealed. The agglomeration between molybenite and talc was caused easily in neutral or acidity solution, and it was dispersing between molybenite and talc particles in alkaline solution. The flotation results showed that good floatability of talc was the key factor causing a low grade of concentrate in alkaline solution. Thus, it is the key factor to enlarge floatability difference between molybdenite and talc.INTRODUCTIONMolybdenum is a kind of important rare metal and strategic reserve resources (Zhitao Y et al, 2016a). Due to excellent characteristic, such as high melting point, good thermal property and et al, it’s widely used in metallurgy, machinery, chemical, aerospace, and many other areas. It has become an indispensable metal in modern industry. Molybdenum generally exist in the form of molybdenite which is a kind of mineral with excellent natural floatability. Talc is a kind of typical hydrous and layered magnesium silicate minerals (Beattie D et al,2006a), which is one of the most common gangue mineral of the platinum group metal ores and metal sulfide ores (Tao L et al,2011). Due to its good native floatability, talc is easy entry into the concentrate product with foam in the process of sulfide ore flotation (Kelebek S and Smith S, 2006b), which resulted in decreasing concentrate indexes. Not on that, the high-content MgO of concentrate will also produce a series of adverse impact to the subsequent smelting (Lotter N O et al, 2008). Therefore, it is difficult to separate talc from sulfide ore concentrate effectively."

Jan 1, 2018

By S. Tuylu, D. Adiguzel, A. Bascetin, H. Eker

"Tailings can be more stable in-site where they are stored and and so the risk of conventional tailings dam accidents can be reduced by alternative methods. In recent years, surface paste disposal (SPD) method is one of the alternative tailings storage methods. According to the results obtained from the previous lab scale experiments, optimum storage design was determined and then, this design was carried out in-site application under atmospheric conditions by a pilot scale tests. In the field study, two separate dams with no environmental hazards were established by the hazardous waste storage directive, whose surface area is measured as 400cm × 200cm. Also physical changes in the paste tailings were measured by the sensors such as volumetric water content, mutric suction and oxygen consumption. In addition, seepage water was collected in the drainage pool and examined for acid mine drainage and metal mobilization risks. As a result of the preliminary data obtained from measurements of pilot scale tests, when the pH value of seepage in the cemented dam (only 1th and 10th layers with cemented) is about 11, the pH value of seepage in the uncemented (reference) dam is measured at 8-9. INTRODUCTION Environmental damages occurred during the deposition of mine process tailings at surface using conventional methods (tailings dam etc.) can be reduced and/or eliminated with the use of new technologies and methods to an important extent. Nowadays, it has been investigated to safely deposit metal mine wastes generally discharged into surface tailings dams, seas, rivers, creeks etc. using Paste Tailing Technology which gains the growing importance in recent years. Meanwhile, Paste Tailings Technology has two applications in industry as an underground paste backfill and surface paste deposition. Particularly scientific studies about deposition of process tailings as paste sample in underground and surface have been increased. These studies showed that surface paste deposition can minimize the free water amount which is the biggest problem in conventional tailings dams. Additionally, it also provides less particle segregation, in other words, the formation of more homogenous material, the development of geotechnical properties which causes to obtain more stable material, increases the strength and stability of the paste with addition of binder where necessary surface paste material, and reduces the risk of Acid Mine Drainage (AMD) (Bascetin et al., 2017a). Theriault et al. (2003), Martin et al. (2006) and Simms et al. (2007) reported that Bulyanhulu mine in Tanzania is the first gold mine to employ surface paste disposal (SPD) worldwide. Here, tailings are deposited alternately via several towers. The tailings flow away from each tower to forming a conical deposit. Each layer had a lower thickness than 30 cm. The fresh tailings were poured on top of drying and hardening layer after a waiting period of 5-30 days. No cement was added into the tailings to prepare paste material. Uncemented paste was deposited by a solid content of 73% which corresponded to a 250 mm slump cone height (Yilmaz et al., 2014). In a study conducted by Yilmaz (2010) illustrates the preliminary results of a field cell testing undertaken to investigate the effect of in situ climate conditions and material properties on the performance and quality of fine-grained, sulphide-rich paste tailings at the LaRonde mine in Quebec, Canada. A total of two field cells are constructed in the surface disposal site of the mine and categorized as cemented cell CC and uncemented cell UC (Bascetin et al., 2017b)."

Jan 1, 2018

By C. Opoku-Ware, M. Kukay, P. Conrad

"This project is exploring the potential for developing trees tolerable to degraded un-reclaimed mine site soils and tailings as a solution to re-establishing long-term tree growth on those sites. The project incorporates growing tree seedlings in an underground greenhouse grown from seeds planted in the degraded mine soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in soils and tailings containing high metal concentrations with minimal post-planting human intervention. The research is being conducted in an underground greenhouse located 100 feet below the surface in the old Orphan Boy Mine Underground Mine Education Center (UMEC) located on Montana Tech’s campus in Butte, Montana. INTRODUCTION In an effort to improve Butte Area One natural resources, the research project was proposed to help restore tree growth in the Butte Priority Soils Operable Unit Boundary (BPSOU). Research by Blicker, et al. (2003) found that, the BPSOU, which is part of the Silver Bow Creek/Butte Area National Priorities List (Superfund) Site within and near Butte, Montana has multiple historic mining sites situated entirely within the urban setting of Butte. Mine wastes and mill tailings, accumulated from over 100 years of gold, silver, and especially copper mining are dispersed throughout Butte, posing health risks to human and environmental receptors. Stabilization of tailings sites is needed to control fugitive dust, prevent run-off of toxic material resulting in subsequent sediment deposition in streams, reducing the volume of water seepage through acidic and heavy metal contaminated material, and improving land productivity and aesthetic VALUES ((Watkin and Watkin, 1982). If successful, the project will help restore water quality and maintain stream flow in Silver Bow Creek where it flows through Butte Area One. Trees native to Butte are being grown in an underground greenhouse located in the UMEC and will be planted in five areas located within the BPSOU designated for tree planting by the Butte Silver Bow government. Growing trees is expected to help restore vegetative ground cover within the watershed contributing to stream flow in Silver Bow Creek. They will prevent soil and tailings from eroding and being deposited in Silver Bow Creek where they could degrade water quality and choke stream flow."

Jan 1, 2018

By E. V. Zelinskaya, V. U. Starostina

"The Irkutsk region is a raw material region. There are a lot of big enterprises for extraction and processing of oil, gas, coal, iron, gold and rock salt. Besides of it, refractory clays, limestone, mica, gypsum and talc are mined in the region. The most important type of mineral raw material is a gold. More than 8.5% of the total mining in the Russian Federation is extracted in Irkutsk region. It is about 0.7% of the world production. The environmental problems of mining and processing enterprises are a complex set of issues that requires of the searching of effective methods to be solved. One of the key environmental problems remains the reduction of waste generation and the introduction of environmentally safe waste management. After analysing different methods of environmental impact assessment it is established that the method of Life Cycle Assessment is one of the most effective methods for mining production. This method base? on the material balance of flows of raw materials, products and waste. The method of Life Cycle Assessment allows to identify the effects of environmental pollution under the influence of mining and processing at a quantitative level and to show real quantitative forecasts of the possibility of managing the flows of raw materials and waste.INTRODUCTION The Irkutsk region is a raw material region. There are a lot of big enterprises for extraction and processing of oil, gas, coal, iron, gold and rock salt. Besides of it, refractory clays, limestone, mica, gypsum and talc are mined in the region. The most important type of mineral raw material is a gold. More than 8.5% of the total mining in the Russian Federation is extracted in Irkutsk region. It is about 0.7% of the world production. The main provider of precious metal is the Bodaibo region. This is a main location for the major ore companies such as “Vysochaishy”, which produces about 5.0 tons a gold per year; “Pervenets”(PJSC Polyus, the largest gold producer in Russia) - 4.5 tons/year, “Druza” - 0, 5 tons/year. Placer gold is extracted by more than 40 enterprises. In connection with this, there are many plans about a building of new and reconstruction of concentrating factories. Consequently, an increase in the volume of processing is expected. The main projects are the construction of a new mill of the Mining and processing plant GOK “Vysochaishy” with a capacity of 2.6 million tonnes of ore per year; the development of the “Uhakhan” gold-field - 23 km from the “Goltsa Vysochaishy” gold-field; the opening in the Bodaibo region the next parts of the gold-deposit ""Pervenets"". Additional, the growth in a gold production can be achieved by a store of gold in the “Sukhoi Log” deposi"

Jan 1, 2018

By J. Lindström, J. Hamuyuni, M. Lundström, J. Aromaa

"The rising demand for metals today, coupled with the scarcity of primary sources for raw materials threatens both technological advancements and industrial manufacturing. In order to meet the demand, metals and other resources trapped in waste streams, have to be harnessed. This philosophy supports circular economy, where metals and other resources are kept in a closed loop. The pickling acid recovery system of most stainless steel production is one such example where the dissolved metals such as iron, nickel and chromium are currently not completely recovered due to the limitations of the current technologies. The aim of this study was to assess the available metals recovery methods from extremely concentrated acids. The main aim is to simultaneously recover metals and keep sulphuric acid reusable in acid circulation process. From the available literature, the most promising methods were chosen for laboratory experiments. Based on experimental work, the results and observations of electrodeposition, solvent extraction, and freeze crystallization are provided. KEYWORDS Pickling acid, metal recovery, solvent extraction, cathodic polarization, Freeze crystallization. INTRODUCTION Pickling in stainless steel production is an essential surface treatment process (Regel-Rosocka, M. (2010); Agrawal and Sahu, 2009). It is applied for removing surface films such as oxides and chromium-depleted layers to improve the corrosion resistance and surface finish of steel (Regel-Rosocka, 2010). Whilst the process greatly improves the surface finish of the stainless steel, it generates large amount of used acid, containing dissolved metals including chromium, iron, and nickel (Agrawal and Sahu, 2009). Recovery of acid is common practice for most steel producing industries (Nyman and Koivunen, 1986). In this work, acid regeneration process is investigated so as to simultaneously reusing sulfuric acid and recovering the dissolved metals. Recovery of valuable metals even in very small amounts would also bring additional revenue to the steel production industry. At a time when metal production has also been challenged by lack of natural resources for raw materials, secondary sources for metals such as the acid pickling process therefore, have greater potential as supplements. From earlier studies, electrodeposition (Giovanardi and Orlando, 2011; Kuznetsov et al., 200; Rögener et al., 2012; Surviliene et al., 2006), solvent extraction (Alguacil and López 1996; Haghshenas et al., 2009; Kesieme et al., 2013) and freeze crystallization (Beyer et al.,2003; Hasan et al.,2017; Van der Ham et al., 1999) are some of the most established potential methods. Earlier studies have also shown that simultaneous recovery of acid and metals would require combination of different methods. This is primarily due to the nature of very stable metal containing complex compounds formed during pickling. These complexes must be broken down to free the metals for further recovery processes."

Jan 1, 2018

By Michael Mann, Kenneth K. Eltschlager

The International Society of Explosives Engineers (ISEE) Standards Committee has recently updated both the Field Practice Guidelines for Blasting Seismographs and the Performance Specifications for Blasting Seismographs. The revisions are the result of public and industry input along with recommendations of the ISEE Blast Vibration and Seismograph Section. The committee is comprised of blasting seismograph manufacturers, users and general interest personnel. On an as needed basis, subject matter experts are enlisted to advise the committee. Three phases of activities are necessary for each revision cycle: request for comment on the existing standard, first draft revision of the standard based on public input, and final draft approval by the ISEE Board of Directors. The ISEE standards revision process will be explained and each standard will be discussed along with the significant revisions from the latest revision cycle.

Jan 1, 2018

By B. J. McKay, K. Schneider, H. B. Nadendla

"A series of experiments were conducted to assess the impact of zinc additions on the morphology and soundness of the interface of Al-Mg compound castings. It was found that high amounts of zinc (>15wt%) are necessary to affect the morphology and microstructure of the interface. At these zinc concentration levels, the formation of the zinc-rich phases t1 and ? were observed along with the Al-Mg intermetallic phases ß and ?. The micro hardness of all phases across the interface was found to be similar, ~200 Hv. This even hardness gradient is thought to avoid mechanical failure in the interface under load. In samples containing large concentrations of zinc (>15wt%), the formation of bubble shaped voids as well as the complete transformation of the aluminium alloy was observed. While the exact mechanism causing the voids has not been identified it thought to be connected to the Kirkendall effect. INTRODUCTION Conventional single material components are increasingly failing to meet the demands, in terms of cost and performance, of the transport industry. Compound castings have been identified as a promising alternative as they possess a number of benefits (Bührig-Polaczek, Röth, Baumeister, Nowack, & Sussmann, 2006). Compound casting is described as a process in which a metallic melt is cast around a solid metal shape. Preliminary research has concluded that for the stability of such a resultant hybrid structure it is imperative that both metals form a sound connection via form closure, force closure, or material bonding. A continuous material bond between the two metals is also highly desirable as the formation of a crevice between the metals could lead to galvanic corrosion, particular in a humid environment (Lao, 2013; Rübner, Günzl, Körner, & Singer, 2011). Even though Al-Mg compound castings could offer the biggest potential in terms of weight savings to date only a limited amount of research concerning such structures exists."

Jan 1, 2018