Search Documents

By Shadia Ikhmayies

Thermo-Calc software was used to investigate the phase diagram of the calcium silicon (Ca–Si) system for the range of Si mass percent 0–100, and temperature range T = 200–1800 K. The melting points of Ca and Si deduced from the phase diagram are very close to the values obtained experimentally. Three stable intermediate solid phases were found, which are Ca2Si, CaSi, and CaSi2, where the first one appeared in the Ca rich side of the phase diagram, and the third one in the Si rich side. In addition, three eutectic points were found at Si mass percents of 3.95, 33.00, 62, and temperatures T = 1048.7, 1519.14, 1308.5 K respectively. Atomic Si (Diamond structure) is found mixed with CaSi2 intermediate phase for temperatures less than 1305 K, and mixed with a liquid CaSi for higher temperatures. These results are important for thermodynamic and metallurgic studies of these intermediate phases.

Mar 1, 2018

By Shihan Zhang, Qingguo Xue, Jingsong Wang, Yaxing Du, Guang Wang

The rotary hearth furnace iron nugget process is in line with China’s energy and resource condition. It has the advantages of short reaction time and high quality iron nugget. The fundamental study on the novel ironmaking process is meaningful. Based on CaO-SiO2-Al2O3-FeO quaternary slag system, the effects of slag basicity and Al2O3 content on the melting of slag were studied. Using the iron concentrate as raw material, the effects of different slag basicity and Al2O3 content on the reduction and melting separation behaviors of carbon composite pellets, such as the starting temperature of melting separation and the morphology of melting separation were studied. Then, the relationship between the properties of slag and melting separation quality was established, which could provide standard for the selection of iron ore for the rotary hearth furnace iron nugget process.

Mar 1, 2018

By Lilong Zhu, Shaoda Zhang, Qian Wang, Shengping He

The effects of ZrO2, Y2O3 and Sc2O3, which are transition metal oxides, on the melting temperature, viscosity at 1300 °C, and break temperature of three mold fluxes (two weak-reactive type and one non-reactive type) designed for the high manganese and high aluminum steels, and one another conventional CaO-SiO2 based mold flux is studied. The results indicate that the melting temperature and viscosity increases slightly, and the break temperature increases dramatically with the addition of ZrO2, Y2O3 and Sc2O3 content in the conventional CaO-SiO2 based mold flux system. While, the addition of ZrO2, Y2O3 and Sc2O3 in the weak-reactive or non-reactive mold flux systems has a negligible in fluence on the melting temperature, viscosity and break temperature, suggesting that these transition metal oxides are possible to regulate radiation heat transfer without changing the basic properties of mold fluxes.

Mar 1, 2018

By Rongjin Zhu, Yue Wu, Shuxing Qiu, Qingyun Zhang, Shengfu Zhang

Co-pyrolysis of biomass and coal was investigated as an effective way to reduce the greenhouse gas emission. The effects of poplar on the thermal behavior of fat coal were studied using thermogravimetric analyzer. The blended samples heated to characteristic temperature were subjected to attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR) to characterize the macromolecular structure. The results indicated that the synergistic effects existed in co-pyrolysis process of blends since lower char yield than calculated values, and the synergistic effects presented positive and negative trend with the increase of temperature, respectively. The carbonyl/carboxyl C=O stretching vibration functional groups and aliphatic side chain from individual fuels were decomposed in advance during co-pyrolysis. Furthermore, the hydrocarbon-generating potential (A-factor) and thermal maturity(C-factor) of the mixtures showed nonadditivity performance.

Mar 1, 2018

By Jizeng Zhao, Li Liu, Weiqing Chen, Jinxia Meng

This paper discusses the utilization of chromium slag, which presently has no useful application in China, as a resource. The following research has been done in this paper: (1) After determining the composition and properties of chro- miumresiduewedecidedtotesttheideaofusingchromiumslagasacomponentin synthetic MgAl O spinel material. (2) Through experiments on sintering and 2 4 electric melting of refractory materials we determined the best conditions for a practical process. (3) We compared the performance of the refractory material obtained with traditional spinel refractory materials and confirmed the excellent performance ofoursystem. The results show thefeasibilityofpreparing MgAl O 2 4 spinel material from chromium slag by electric melting. (cid:1) (cid:1)

Mar 1, 2018

By Xuemei Zheng, Aiyuan Ma, Guojiang Li, Tingfang Xie, Jinhui Peng, Libo Zhang

A new microwave roasting technology for the removal of Cl from zinc oxide dust is proposed in this paper. The effect of important parameters, such as roasting temperature, holding time and stirring speed, were investigated and the process conditions were optimized using response surface methodology (RSM). The experimental results show that zinc oxide dust dechlorination rate can reach more than 95.66% and meet the requirements of wet smelting electrolysis when controlling the stirring speed of 60 r/min,roasting temperature of 650 °C, holding time of 30 min. In addition, the effect of roasting temperature and holding time on removal ef ficiency of Cl was most signi ficant. As a result, the Cl content was decreased without the risk of pollution. This makes it as a good choice for a more ecological treatment of zinc secondary resources.

Mar 1, 2018

By Shangshu Li, Xionggang Lu, Xingli Zou, Zhongya Pang, Kai Zheng, Yinshuai Wang

Metal carbides (MCs), especially transition metal carbides have attracted a lot of attention due to their unique properties, such as high strength and hardness, good chemical and thermal stability. In this paper, a new route was proposed for preparing TiC nanoparticles directly from TiO 2/C precursor by using solid oxide membrane (SOM) technology in molten CaCl2. The TiO2/C pellet pressed under 8 MPa was used as the cathode, and a yttria-stabilized zirconia (YSZ) tube filled with carbon-saturated liquid tin was served as the anode. This process employs an inert SOM to separate the anodic reaction area from the molten electrolyte to control the electrolysis process. The electrochemical process was carried out in molten CaCl2 at 1000°C and 4.0 V from 0.5 to 4 h. The characteristics of the phase composition and morphology of the electrolysis products were investigated. The product electrolyzed was examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS). The results show that TiC nanoparticles can be obtained directly from TiO2/C mixture at 1000 °C, 4.0 V and for 4 h in molten CaCl 2 and the current efficiency is calculated to be 74.1%. In conclusion, we suggest that the SOM process is a promising environmentally friendly and low energy costs electrochemical method for the facile and controllable electrodeoxidation of MO x/C precursors to micro/ nanostructured MCs.

Mar 1, 2018

By Onuralp Yucel, Osman Halil Celik, Hakan Morcali

In this study, some experiments were performed for the dimensional control, pre-treatment, getting salt, metallic aluminum and aluminum oxide into the solution of 15 kg aluminum black dross obtained from a private company which recycles aluminium drosses. Water leaching experiments are done for removing salts and aluminum nitride. Temperature stirring speed, solid-liquid rate are investigated while water leaching experiments. Removing of AlN is provided at 25 °C at a rate of 42.48%, at 80 °C at a rate of 86.4%. Leaching experiments performed with NaOH. NaOH concentration and time was analyzed. Efficiency of including metallic aluminum into the solution is determined to be 98% approximately. Melting (fusion) experiments were performed with NaOH at high temperatures to include aluminum oxide in the structure of the remaining after dissolving process into the solution and after dissolving the resulting structures in water, efficiency of including aluminum into the solution is determined to be 85%.

Mar 1, 2018

By Wangzhi Zhou, Huasheng Chen, Bowen Li, Meng Liu, Mingsheng He, Long Zou

Steel slag is an inevitable by-product from a steelmaking furnace such as a converter, an open-hearth furnace or an electric arc furnace. The yield of steel slag increases with the sharp rise of steel production. Utilizing the slag effectively and comprehensively is one of the important tasks to promote the development of iron and steel industry in China in a sustainable and efficient way. In this study, hot-poured steel slag from a converter was used to prepare ceramics by mixing with fly ash, microsilica, and quartz. After heating at 1100–1200 °C, the ceramics were well sintered. XRD revealed that multiple crystalline phases coexisted in the glass-ceramics, and the main crystalline phases were diopside and anorthite. SEM observation indicated that there was a plate-columnar composite structure in the ceramics. Reaction mechanisms were discussed.

Mar 1, 2018

By Wufeng Jiang, Jiann-Yang Hwang, Suju Hao, Yuzhu Zhang

Lime was made by the calcination of limestone in a high pressure resistance furnace. The lime mineralogical phases and micro-morphologies was characterized by field emission scanning electron microscopy (FE-SEM). The lime activity degree was determined by acid-base titration, and the lime pore distribution was measured by mercury intrusion porosimetry (MIP). The results show that with the increase of calcination pressure, the lime activity degree is increased, and the lime develops a large pore structure. The desulphurization experiments were carried out in the induction melting furnace using active lime with different activity degrees as a desulfurizer. The results show that the desulfurization performance of lime is closely related to the activity degree. There is a strong positive linear relationship between the desulfurization rate and the lime ’s activity degree.

Mar 1, 2018

By Hong Peng, James Vaughan

Thermal activation of bauxite has been proposed to enable bauxite dissolution at a reduced digestion temperature and also to reduce the organic content in the liquor. Research has been carried out on phase transformation of its main hydroxide components (gibbsite, boehmite and kaolinite) during calcination. However, there is limited information available on phase bauxite phase transformation during thermal activation. In this study, two bauxite ore samples were heated from 25 to 700 °C at a rate of 50 °C/min while monitoring the phase transformation using Rigaku in situ XRD. Different phase transformation pathways for gibbsite in the bauxite compared with pure gibbsite was observed. Boehmite and kaolinite in bauxite behaved similarly to their pure phases. The temperature of phase transformation depends to some extent on the bauxite sample. Samples were also characterised by scanning electron microscopy (SEM) to reveal changes in the microstructure.

Mar 1, 2018

By Zhengen Zhou, Dachun Liu, Baoqiang Xu, Bin Yang, Yong Deng, Heng Xiong, Jia Yang

The thermogravimetric method was selected for investigating the evaporation of Sb2S3 in the pressure range of 50–300 Pa and in the temperature range of 823–1123 K, the gas phase diffusion was the rate-determining step for Sb2S3. The volatilization rate was related to the temperature and pressure, that the logarithm of volatilization rate yielded a line with the reciprocal of temperature and pressure. The volatilization rate for Sb 2S3 was between 0–0.023 g/C1 cm−2/C1 s. The apparent activation energy was between 65.8 and 60.6 kJ/mol.

Mar 1, 2018

By Naiyang Ma

Along with fast growth of EAF steelmaking, better ways of treating EAF dust have been continuously pursued for better environmental protection and better economic benefits. In this contribution, various ways of collecting EAF dust in EAF off-gas cleaning systems are reviewed, and generation of dust and concentration of zinc in the dust from various collecting devices are examined. Accordingly, recycling of EAF dust through source separation is discussed.

Mar 1, 2018

By Wang Jingsong, Ma Tengfei, Feng Fu, She Xuefeng

In this paper the direct reduction melting separation-leaching process is investigated on recovering rare earth from rare earth Bayan Obo complex iron ore (REBOCIO). The REBOCIO was reduced and melting separated to produce iron nugget and rare-earth-rich slag at 1400°C for 12 or 15 min. The RE2O3 is enriched into Ce 4.667(SiO4)O or Ca 3Ce2[(Si,P)3O4]3F, which closely depend on chemical components, especially basic. The optimal acid-leaching parameters of rare earth elements from the rare earth slag are suggested as the hydrochloric acid concentration, the ratio of solid to liquid, leaching temperature, and the leaching time are 1 mol/L, 1:14, 50 °C and 120 min, respectively. The rare earth elements leaching efficiency are more than 95%. Adding of calcium CaCO3 and sodium Na2CO3 in direct reduction process have great in fluence on leaching ef ficiency of thorium.

Mar 1, 2018

By S. N. Monteiro, E. B. Zanelato, J. Alexandre, M. T. Marvila, A. R. G. Azevedo, G. C. Xavier

The incorporation of industrial waste into ceramic tiles is a major trend in the search for alternative raw materials, and also in the search for environmentally correct disposal of waste. In order to evaluate the effect of the incorporation of residues from the ornamental stone industries, in the properties of ceramic tiles, incorporations of up to 40% by weight of the residue in ceramic mass were studied. It is noteworthy that this residue is constituted basically by limestone and its characterization was performed by grain size analysis, Atterberg boundaries, grain density and chemical analysis by X-ray fluorescence. The specimens were burned at 800 °C and the following properties were evaluated: linear retraction, water absorption and bending rupture stress. The results indicated that the residue of ornamental rocks is a material with potential to be used as a component in the mass of red ceramic tiles.

Mar 1, 2018

By Tiejun Chun, Gutian Mu, Jiaxin Li, Hongming Long, Zhengwei Yu, Ning Li

The basic characteristics of iron ore, including assimilation, fluidity, cohesive phase strength and the ability to produce calcium ferrite, are often used to evaluate the sintering properties of iron ore and guide the optimization of iron ore blending. Six kinds of common iron ore used in a steel company in China were selected in this work. The basic characteristics of the single iron ore and blended iron ores were studied, as well as the difference between weighted averages of basic characteristic index of single iron ores and the real value of basic characteristic index of blended iron ore under different ore blending ratios. The results shew that the liquid phase liquidity, cohesive phase strength and calcium ferrite formation ability had a significant linear positive correlation with SiO2 content. The weighted average of basic characteristic index of single iron ore cannot fully reflect the actual blended iron ore properties. The optimization of the blending ratio can be achieved through the detection of the basic characteristics of the mixed iron ore, combined with the basic characteristics of iron ores.

Mar 1, 2018

By Konstantinos Salonitis, Joanna Mielnicka, Mark Jolly, Arun Prabhakar

Lead sheets are widely used for roofing applications, radiation protection and sound proofing. Most of the sheets are either produced by rolling cast slabs of lead sheets or via the direct method (DM) of casting of the sheet continuously. The DM method comprises of a rotating water-cooled drum that is partly immersed in a bath of molten lead and sheets are cast out continuously. The direct method of casting lead is more energy efficient compared to the rolling process which requires a casting process before rolling to achieve the required thickness. This work investigates the energy consumption in different stages of the DM process and suggests pointers for improvement. An energy audit of the process is conducted and the consumption is analysed at different stages and compared with rolled lead.

Mar 1, 2018

By Qian Li, Honggui Han, Jun Wang, Shichao Yu, Chunxiao Zhao, Maoxing Hong, Rui Liao, Xingxing Wang

In this study, bioleaching experiments, synchrotron X-ray Diffraction (SR-XRD), X-ray absorption near edge structure (XANES) and X-ray Photoelectron Spectroscopy (XPS) were conducted to investigate the intermediates and surface species of bornite leached by mesophilic mixed bacteria of Leptospirillum ferriphilum, Acidithiobacillus caldus and Sulfobacillus thermosulfidooxidans. CuS, Cu9Fe9S16 and S8 were the main intermediate species during bornite bioleaching by mesophilic mixed bacteria, and CuFeS2 was also detected. The surface species of S2− and S2 2− would be polymerized to Sn 2− during bioleaching. The formation of element sulfur and the increase of its content were confirmed by the fitted results of XPS spectra. The presence of polysulfide and element sulfur did not inhibit the bornite bioleaching. The formations of CuS and CuFeS2 were confirmed by the results of Cu K-edge XANES spectra.

Mar 1, 2018

By J. A. S. Tenorio, K. S. Barros, D. C. R. Espinosa

Considering the risks involving the use of cyanide, other complexing agents have been evaluated for the treatment by electrodialysis of the effluent of brass electrodeposition and among them, EDTA is interesting since it has been already tested for many years to separate ions. The main objective of the present paper was to evaluate the occurrence of fouling and scaling on the surface of the anion-exchange membrane HDX 200 by the construction of chronopotentiometric curves and speciation diagrams in different conditions (pH between 10–12 and proportion of cupric ions of 30%, 50%, 70%). According to the results, the chronopotentiometric curves did not show additional inflexion points typical for the cases which occurs fouling and scaling for the pH values evaluated, which is in accordance with the speciation diagrams of the solutions constructed with the aid of Hydra-Medusa software. Hence, the pH and the proportion of cupric ions did not show influence on the curves behavior.

Mar 1, 2018

By Ari Jokilaakso, Dmitry Sukhomlinov, Keiran Holland, Pekka Taskinen, Ville Naakka

This study is focused on distribution of Co, Ni, Ag, Au, and Pd between molten copper and molten copper sulfide (‘white metal’) phases in copper converting conditions. The behavior of the elements selected was studied experimentally at 1300 °C and at various sulfur dioxide partial pressures (0.01, 0.05, 0.1, 0.5, and 1 atm). The experimental technique employed involves a high temperature equilibration followed by rapid quenching in ice water, with subsequent quantitative elemental analysis of the equilibrium phases with an electron micro probe analyzer. The distribution coefficients LCu=wm Me determined in this work can be arranged in the following sequence: Co < Ag < Ni < (Au, Pd).

Mar 1, 2018