Search Documents

By J. Dean Warner

In 1984 and 1985, as part of its critical and strategic minerals studies, the Bureau of Mines investigated lode and placer tin occurrences near Rocky Mountain (Lime Peak), in east-central Alaska. The lode occurrences consist of mineralogically complex, generally fault-controlled veins, and contain an average of approximately 0.05 pct Sn, as cassiterite. Beneficiation testing of two bulk samples of the vein material produced concentrates containing 65 and 59 pct of the total tin values at grades of 0.35 and 13.9 pct, respectively. Although as much as 30 million short tons (MMst) of mineralized rock containing up to 20 MMlb Sn may be present, the grade of these occurrences is too low to be considered economic at this time. Trace amounts of cassiterite were also identified in surface samples of glacial out-wash gravels collected along North Fork Preacher Creek, which partially drains the area of tin lode deposits near Lime Peak. Low tin grades in the samples do not account for the former erosion of a large volume of lode tin mineralization from near Lime Peak; higher tin grades may be present in gravels closer to bedrock.

Jan 1, 1988

By S. S. Peng

Since the introduction of shield supports in 1975, safety and production in U.S. longwall faces have improved considerably. Many faces had a daily production of up to 8,000-10,000 tons and productivity reached 600 tons per man-shift. But a longwall face requires expensive equipment which slows down the growth rate of the percentage of longwall production. Among the equipment cost the shield support accounts for 50-60%, a very large proportion. Therefore, it will have a large impact on the growth of longwall mining in the U.S. to reduce the support cost (1).

Jan 1, 1988

By Robert G. Telewiak

During the past few years, the international nickel industry has taken some important steps to respond to conditions of global production overcapacity, relatively flat demand and low prices. These include the implementation of major cost reduction programs by most producers, closure of some high cost operations and the establishment of the Nickel Development Institute. Consumption in the western world increased by about 7 per cent in 1987 compared to 1986, supplies were less than demand, inventories were low, and late in the year prices increased dramatically. By year-end 1987, most producers were operating at, or close to, their effective capacities. Nickel demand is expected to increase to the year 2000 at an annual rate of about 1.7 per cent, led by increasing usage in the stainless steel sector. If this rate of growth is realized, then there will be need for the effective capacity of the nickel industry to be increased. Producers in Canada have put considerable effort in the past few years into reducing costs - with impressive results. Mining costs, in particular, have been reduced dramatically. While production is still less than the peak years of the yearly 1970's, it has increased substantially from levels of the early 1980's. Over the next few years, production is expected to increase slowly. A key determinant of the level of production in the 1990's could be the effect that regulations on sulphur dioxide emissions have on limiting production.

Jan 1, 1988

By Weatherhead J, Grounds J

The Nabarlek Uranium Project located in Arnhem Land in the Northern Territory of Australia was a small high-grade deposit which was the first uranium mine brought into operation following the extensive Commissioner Fox Inquiries into uranium mining during the late 1970s. The operation is almost complete and decommissioning plans have been prepared. This paper reviews all phases of the water management and tailings disposal for the project and compares results with design predictions.

Jan 1, 1988

By T. Fujita

The removal of phosphorus is essential 1n order to increase the recycling of steelmaking slags for their manganese, iron and lime contents. This study aims at establishing the phosphorus mineralogy and its distribution in steelmaking slags, the effect of slow cooling, and the methods of phosphorus removal. A series of steelmaking slag samples was prepared at different cooling rates, and the mineralogy, chemistry and grain size of the samples were investigated with SEM/EDS and x-ray diffraction. The test results using high gradient magnetic separation are discussed.

Jan 1, 1988

By Liu C. H, Juang Y. F

Coal/gas outbursts were one of the rather difficult safety problems faced in the coal mines of this Country, with coal fields characterized by frequent disturbances of folds, faults and pinch-offs. With average mining depth about 500m below surface, several such accidents occurred with up to 500 tonnes of coal outburst. In recent years, after a series of improving countermeasures had been undertaken, gas outburst accidents had been greatly decreased. The characteristics of gas outbursts in Taiwan coal mines include relating to coal petrography, mining depth and the other deformation forces. All these have been investigated, trying to determine the parameter of outbursts under natural conditions. The preventive countermeasures include predicting tests, de-stressing boring in coal seams, the emergency procedures during outbursts and certain improving options.

Jan 1, 1988

By Doris M. Hyde

The 350,000-barrel-per-day Bahamas Oil Refining Co remained closed throughout 1986. Financially troubled Charter Oil Co., joint owner of the refinery with Chevron Oil Bahamas Ltd., agreed in principle to have Chevron assume full ownership in return for canceling debts owed Chevron. Finalization of the agreement was pending at yearend. Burmah Oil Ltd. took more than a $30 million loss on the sale of its interest in South Riding Point Grand Bahama Transshipment Terminal to South Riding Point Terminal Holding Ltd.

Jan 1, 1988

By Diane M. Doyle-Coombs

In late July 1985, air samples from a sealed portion of the Quinland coal mine in West Virginia showed the presence of carbon monoxide (CO). Mine Safety and Health Administration (MSHA) personnel concluded that a fire was burning behind the seals. Since an imminent danger existed, the mine operator was given a closure order. The gases behind the seals were monitored and almost 2 million ff of carbon dioxide (C02) gas was pumped into the sealed area to stabilize the environment. Sixteen days after the closure order was issued, MSHA allowed the mine to return to production. Approximately 1 yr later, mine management submitted a seal breaching request to MSHA in order to drive a set of entries to further develop the mine. The Bureau of Mines established a sampling strategy and monitored gases from behind the sealed area during the breaching operation until the atmosphere was safe. This report is an account of the seal breaching conducted by the mine, MSHA, and the Bureau. The logistics of this event, the sampling strategy, and the equations applied could be used by the mining industry in future breachings or mine recovery operations. Time to reenter the area was calculated by using the methane (CH4) concentrations sampled at the discharge of the seals. Tracer gas was used to verify the ventilation flows through the area.

Jan 1, 1988

By Barry Welch, Kai Grjotheim

"The capital intensive nature of the present process for aluminium smelting, the low productivity per unit reactor, and pressure to reduce the electdcal energy demand have motivated the search for an alternative process. Optional routes include carbo-thennal reduction of alumina (using an alloy phase immediate), chlorination followed by electrolysis of aluminium chloride, and electrolytic decomposition of alumina using inert electrodes. Materials performance and reactor design constraints have been a major limitation for alternatives. However parallel research has led to considerable advances in the process efficiencies and scale of both the Bayer process and the Hall-Heroult cells.Future development of alternatives is dependent on breakthroughs in Materials Science such as the development of stable conducting anodes and stable wettable cathode materials. However if successful it is probable that some spin-offs will be retrofitted to existing cells. Therefore the basic Hall-Heroult technology will continue as the dominant process for at least the next half century.IntroductionThe present Bayer/Hall-Heroult process for production of aluminium is just over 100 years old. Frequently, during the century of its technological development questions have been raised as to whether it is the ideal route for metal production. The questioning was particularly intense in the period between the mid-1950s and the mid-1060s when the limitations of the Hall-Heroult electrolytic stage were evident. Then the cells were only 30 to 35 % efficient with respect to the utilisation of the hydro-electricity (requiring 16 18 kWh/kg, thus making it strongly dependent on cheap electrical energy), while the size of cells being installed were 80 to 130 kA. Hence the process was capital intensive, the productivity per reactor volume low, and the process was labour intensive (requiring about 15 man hours per tonne of aluminium). In addition, the use of pitches for Soderberg anodes and the fluoride electrolyte were creating problems through emission. At that time material science had paid little attention to the manufacture and use of carbonaceous materials or the development of alternatives that were corrosion resistant to cryolite or liquid aluminium. Hence cell lives were short - typically 600 to 1000 days - thus adding to operating costs. Thus the grass over the fence, as foreseen in 1960s vintage crystal balls appeared much greener for alternative processes."

Jan 1, 1988

By Guenter F. Lehmann

This report summarizes the results of the development and testing of a prototype monorail suspended bridge conveyor (MBC) system as a method of continuous haulage In underground mining applications. Included are the results of full scale, surface and underground testing of the complete MBC system. Conclusions drawn from these results, together with recommended modifications, supports the viability of the MBC system.

Jan 1, 1988

By G. L. Hundley

The Bureau of Mines has devised a procedure to recover chromium chemicals from concentrates derived from low-grade domestic chromites. These domestic chromites contain silicon and aluminum impurities at levels that are too high to permit processing by present industrial processes. The Bureau procedure consists of reacting chromite with molten NaOH under oxidizing conditions to form sodium chromate (Na2Cr04)' The reaction product is leached with methanol to recover the majority of the unreacted NaOH, then with water to extract the Na2Cr04 and the remainder of the NaOH. The Na2Cr04 product is recovered by evaporative crystallization from the aqueous solution. This report presents laboratory results of studies to determine the optimum leaching conditions for the reaction products of several domestic chromite concentrates. Results of solution purification and crystallization studies are also presented. The concentrates are from a variety of sources including the Stillwater Complex in Montana, Red Bluff Bay and the Kenai Peninsula in Alaska, and a Ni-Co laterite from southern Oregon. Sodium chromate crystals were produced that contained less than 0.01 pct NaOH.

Jan 1, 1988

By E. C. Baker

The capital investment and operating costs of two methane-control systems used during longwall mining operations are compared in this Bureau of Mines report. Costs are given for a surface gob hole drainage system and an underground cross-measure borehole drainage system to control methane gas in gobs in four coal mining areas--central Pennsylvania, northern West Virginia, southern Virginia, and northern Alabama. Present-worth analysis is used to determine the more cost-effective alternative in each location. The alternatives have equal lives and provide the same service based on a minimum rate of return of 15 pet. In central Pennsylvania and northern West Virginia, the gob hole system is more cost effective than the cross-measure system, by 10 and 18 pet, respectively. In southern Virginia and northern Alabama, the cross-measure system is more cost effective, by 29 and 38 pet., respecitively. Costs for other locations must be developed on a case-by-case basis.

Jan 1, 1988

By S. D. Thompson, L. Adler

This study reviews and analyzes the empirical methods available for designing the capacities of coal mine gathering belts. The analyses lead to recommendations concerning the application and implementation of each empirical method. Operations research techniques, mainly simulation models, are also briefly mentioned, and a few recommendations are made concerning their selection and application. The objective of the study is to provide a reliable basis for the practicing engineer to properly select, apply, and implement a capacity design method.

Jan 1, 1988

By Charles F. Seemann

It is with considerable trepidation that I set out to defend "litigation" to Design Professionals (DPs), as a better method of resolving disputes than arbitration, in the light of my personal feeling that an increasing amount of America's productive process is being squandered in litigation. Newer methods of dispute resolution, particularly arbitration, are fashionable, and opponents of these schemes risk being viewed as cynical or self-serving. My quandary is heightened since for some smaller disputes, arbitration seems clearly the better choice. I must concede, for example, that when the cost of dispute resolution--i.e., the cost of the process (such as arbitrators fees, attorneys fees, etc.), plus the cost impact of the non-productivity of involved employees--approximates the amount of the dispute, controlling that cost may be as important as a correct resolution. This principle is particularly true for small disputes arising during the progress of a project; it is probably more cost-effective for all parties to resolve their disputes quickly than permitting the dispute to drag out.

Jan 1, 1988

By N. Panagiotopoulos

A low-grade (1.06% Ni, 0.06% Co) hematitic type lateritic ore from Triada, Euboea Island, Greece, has been leached with sulfuric acid at atmospheric pressure for the extraction of the contained Ni and Co values. The effect of various parameters, including reaction time and leaching temperature, acid strength, pulp density, etc., on Ni, Co extraction and Fe dissolution was determined. By leaching at 95°C for 4h with a 3N sulfuric acid solution at 25% pulp density, Ni and Co extractions were 82 and 75% respectively, and Fe co-dissolution 28%, yielding a pregnant solution containing 2.7 g/l Ni, 0.16 g/l Co, and 33 g/l Fe. Overall acid consumption was 850 kg/t ore (or 100 kg/kg Nil. Preheating of the laterites at 600°C before leaching resulted in much faster leaching kinetics for Ni, but the final extraction and acid consumption remained unaffected; Fe extraction was not influenced. Three-stage counter-current leaching at 9S°C, using 2N acid strength at each stage and 35% pulp density, reduced acid consumption to 350 kg/t ore (41 kg/kg Nil, and yielded 81% Ni recovery. Percolation leaching of -10 mm laterite at ambient temperature with 3N acid for 7 days resulted in 58% Ni extraction.

Jan 1, 1988

By A. L. Wilder

Coeur d'Alene Mines Corporation's newest precious metals property is located in the old Rochester Mining District approximately twenty-five miles northeast of Lovelock, Nevada. Built at an elevation in excess of 6 000 feet, the Coeur-Rochester gold silver heap leach property encountered cold weather operational problems typical of most northern Nevada heap leach properties, soon after the start-up of operations last fall. Due to the size of the heap area under leach at Rochester, it was decided that 1 the usual practice of spraying to an "ice field" and waiting for the spring thaw was impractical. Further, the delivery schedule for a solution heating system of the size required was unacceptable. Accordingly, Rochester personnel embarked on a program to seek out a leach solution distribution system that would enable an operation through the winter and yet be cost effective. The findings of this program were rather dramatic and, as a result, the whole perception of heap leach solution application at Rochester has changed forever.

Jan 1, 1988

[Determine how subsidence resulting from underground coal mining affects surface structures, and evaluate the usefulness s of the tiltmeter for monitoring foundation movement. Approach The Bureau of Mines is studying foundation response to mine subsidence in order to determine how subsidence-induced ground movements affect foundations in place directly above the mint. These investigations are essential if economic mitigation and repair techniques are to be made. In addition, commercially available tiltmeter are being evaluated (or use as a cost-effective monitoring technique. To study foundation response and to evaluate the tiltmeter system, full-scale model foundations were constructed, instrumented, and monitored for three years. Vertical and horizontal displacements, tilt magnitudes and directions, and observed damages were recorded. Displacements were compared with measured lilt to determine if the tiltmeter was tracking foundation response to subsidence, The Bureau developed a computer software package to aid in the reduction and analysis of the tiltmeter data.]

Jan 1, 1988

Au airway hteat and moisture exchange .,Jgorithm is described which is generalised to suit most mining situations and can be run separately on a microcomputer or used within a network simulation. The main difference between this technique and other simplified methods is that a non-uniform boundary condition is allowed for. This permits radiative heat transfer between surfaces of different wetness in addition to evaporative and convective heat and mass transfer.

Jan 1, 1988

By P. Koskinen

Outokumpu Oy has 30 years' experience in nickel production. It is mainly based on the technology developed within the company. The production chain starts from the mines reaching to the high-grade cathode nickel and the stainless steel manufacturing. As a multi-metal producer Outokumpu has the advantage to exploit from nickel raw materials also other valuable metals and intermediate products which can be processed at the company's various plants. The main source of nickel concentrate is nowadays the Enonkoski Mine started up in early 1986. It is the most modern mine in Finland being provided with the latest Finnish high-tech systems. Nickel concentrates are smelted at the Harjavalta Works using Outokumpu's internationally well-known flash smelting method. Also nickel containing residues and secondaries' are used as raw materials. The high-grade nickel matte from the smelter is then refined at the nickel refinery in a hydrometallurgical process, which was also developed by the company's own research staff. These processes have been continually improved and capacities gradually enlarged to 18 000 mtpy of cathode nickel. Besides plating, melting and superalloying purposes part of the nickel ends in stainless steel at the Tornio Works. The production was started in 1976 and has reached an established position on the European market.

Jan 1, 1988

By Frederick K. Allgaier

This report presents the final data from a 5-yr Bureau of Mines study designed to determine the surface subsidence characteristics resulting from longwall coal mining in a geologic environment common to the Western United States, It includes a description of the geologic setting of the study site, the mine plan, measurement techniques, and results of the monitoring program. Measured subsidence values were obtained over four adjacent longwall panels- Major subsidence characteristics such as longitudinal and transverse profiles, angles of draw, time-related subsidence development, and critical width are discussed. The maxima subsidence value of 5.8 ft was 68 pct of the mining thickness. The average angle of draw was 30°, Subsidence at the center of the first panel continued for 46 months following undermining. The lengths of the longwall panels precluded a definitive determination of the critical width and maximum possible subsidence.

Jan 1, 1988