Search Documents

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof' stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division's deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By P J. Hommert, D S. Preece

"Commercial development of the United States Oil Shale reserve will require substantial amounts of mining. In fact, even a modest 500,000 barrels per day industry requires a mining effort equivalent to nearly half of the current U.S. coal mining industry. Obviously, mining efforts on this scale will benefit from technological advances. There are a number of areas where advanced technology could impact mining. These include continuous miners, shale transport systems, and blasting. This paperexamines recent developments in computer modeling of blasting and assesses the likelihood of these advances being applied to practical oil shale mining problems."

Jan 1, 1989

By Egon Berger

"In recent years the trend in underground metal mining has been toward ever increasing blasts (often in excess of 100 000 tonnes per blast). The Canadian mining industry has been in the forefront of these developments (VRM, LBHand cable bolting to stabilize the surrounding rock /avoid dilution).In order to move these large tonnages, efficient loading systems have to be developed. This paper shows the technical and economic implications of various loading scenarios based on a predefined (however typical) stoping layout by:1 . discontinuous loading using scoop trams;2. discontinuous loading using scoop trams in combination with low profile dump trucks;3. continuous loading (based on loading performance/operating costs of the AL-60) in combination with low profile dumptrucks.The cost advantages of production concentration (loading large tonnages from one drawpoint}, made possible by continuous loading as opposed to sea tiered mining (small tonnages), using discontinuous loading in tunnelling will be presented, based on actual results obtained in a decline development project using the A L-60 continuous loader. At as pacing oj150m between turning bays, it was found that continuous loading was out performing discontinuous loading in approximately80% of the overall decline development.Fuel consumption and total cycle times are compared, and a cost assessment is presented.INTRODUCTIONThe subject of this paper deals with the introduction of continuous loading in underground metal mining and single heading tunnelingContinous mining has been widely introduced both in underground and surface coal mining. Mechanized longwall mining, utilizing moveable shield supports in combination with double drum- shearers, has resulted in a tremendous increase of coal production per working face.This has led to very concentrated mining operations. In a typical German coal mine two mechanized longwalls nowadays would produce the same amount of coal as 12 to 15 longwalls in the 1950s. One longwall in a South African coal mine has recently set a world record with 120 000 tonnes of coal in a single month.In underground metal mines-often due to the irregular nature of the ore body and the mining methods used-mining is far less concent rated. Ore is often produced from a large number of stopes and production sections. Sometimes, a substantial amount of ore may be obtained from development in the orebody (40070 at a German base metal mine)."

Jan 1, 1989

By J. M. Mutmansky, S. Padmanabhan

"The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Ucah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7.The results will be presented using two categories of data collected during two separate phases of the research:(l) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and(2) quartz concentration data from mines chosen at random.The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent."

Jan 1, 1989

Tougher physical mining and processing conditions as well as economic circumstances are causing many mining companies to re-evaluate the effectiveness of their mine planning. The recent wave of inexpensive computing power provides the engineer an opportunity to go beyond the simple one-off manual mine design and production schedule. The basis of a good mine plan is a good reserves model. Concepts of mine model development are explored. The only advanced computer methods that have found consistent success in optimising mine planning functions are economic pit limits determination and material scheduling. Three pit 'optimisation' methods are examined; the moving cone, the Lerchs-Grossman 3-D graph algorithm, and the new network flow algorithm. A comparison between the methods in terms of total profits generated and computer time involved are made. The results show that both algorithms produced a higher profitability than the simple moving cone, but at much higher execution times. However, the profit increase never exceeded much more than 1 % of the base moving cone case. Finally, a method for the development of long range material production schedules with forward waste planning is presented.

Jan 1, 1989

By J. A. Elliot

Deep Mix-in-Place soil stabilisation is achieved by forming columns of soil/cement arranged to overlap by secant intersection. Alternate columns are constructed initially and infilled. The cementitious material injected is designed to retard the strength of the resulting mix thereby allowing satisfactory overlapping. Columns are constructed using a designed large diameter mixing auger mounted on a smaller diameter auger stem. This is firstly screwed to the design depth removing only such spoil as to enable penetration of the auger, and subsequently counter rotated and extracted in a predetermined mixing pattern and grout injection rate to ensure continuous and homogeneous treatment through each successive level. The process is performed whilst monitoring auger depth, grout flow and pressure. Cementation Piling and Foundations Limited used this technique to stabilise allu­vium and to facilitate the construction, by conventional techniques, of a circular pumping station pit of 10M diameter to 10M below ground level. The work was carried out within 3M of adjacent domestic properties, and on a very restricted site in Elland, West Yorkshire. Ground conditions consist of 2M of cohesive alluvium becoming water bearing and increasingly sandy and gravelly with cobbles which overlies the mudstones at 10.0m depth. Sandstones beneath formed an aquiclude to artesian ground water with the underside of the open excavation approxi­mately 1.0M from the top of this material. Peripheral treatment into the mudstone, coupled with pressure relief wells, proved successful and final excavation depth was achieved in "the dry".

Jan 1, 1989

By Thomas J. Peters

In 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 34,310-acre Diablo Mountain (Additional) study area (OR-001-058), in order to evaluate its identified mineral resources and occurrences. The study area lies along the east shore of saline Summer Lake in Lake County, OR, about 145 miles southeast of Bend and 45 miles northwest of Lakeview. The climate is semiarid and temperate, and the study area is almost treeless. Geologically, the (Additional) study area is in a region of fault block-formed mountains and basins, characterized by interior drainage. The area is mainly underlain by unconsolidated Quaternary and Pleistocene lake and playa sediments, which may include subsurface evaporite mineral deposits and resources. Near the center of the eastern margin of the study area are an occurrence of dolomitic limestone of unknown extent, and an area of basalt outcrop totaling 1.5 square miles. A veneer of windblown sand covers about one-half the study area.

Jan 1, 1989

By Henry J. Kellner, Michael J. Brnich

This U.S. Bureau of Mines report addresses issues involved in using a limited number of training apparatus to give hands-on self-contained self-rescuer (SCSR) training to a succession of miners, and provides guidance regarding methods for minimizing the spread of infectious diseases. Procedures used for preventing the spread of infectious organisms in dentistry, cardiopulmonary resuscitation (CPR) training, and scuba training are examined. The sanitizing methods of three organizations that require individuals to insert the mouthpiece as part of the SCSR donning sequence are discussed. It was found that each of these organizations was able to render their mouthpiece assemblies microbe free simply and inexpensively.

Jan 1, 1989

By Robert A. Jankowski, J. Drew Potts

The Bureau has identified several ventilation techniques and a water spray application for reducing auger mining dust levels. The dust control methods all work by improving air quantity or flow patterns at the face. Section airflow is maximized by reducing air leakage between entries. Sealing stoppings with brushed- on mortar, containing fiberglass additives, reduces leakage. Heading airflow is maximized by properly installing the brattice curtain and keeping the area between the curtain and rib free from obstructions. The brattice curtains should be hung at least 1.7 m (5.5 ft) from the ribs in 7.9 m (26 ft) wide entries and kept less than 4.6 m (15 ft) from the face. A tight curtain seal is created by using the mine air pressure to force the curtain against the timbers, roof and floor of the mine. Using both a blowing curtain and an exhausting curtain will isolate some face workers from dusty air. The Bureau designed, auger clearer spray system, can be used to force heading air across the active face. Laboratory tests indicate that the auger clearer spray system can increase face velocities by more than 0.5 m/sec (100 ft/min), while using less than 0.13 l/sec (2.0 gal/min) of water.

Jan 1, 1989

By Dwayne C. Kicker

This paper introduces the concept of design theory and methodology as applied to rock mechanics for more innovative and efficient design. This is a "frontier" research area in rock mechanics because although design is a fundamental foundation to all engineering branches, very little attention has been paid to this aspect in mining. In discussing the theoretical premise of design, this paper identifies the principles which form the basis of design activity. Also, from a practical viewpoint, the findings from a series of interviews with mine design engineers are presented. These findings lead to the identification of needs arising from overlooked design methodology in practice.

Jan 1, 1989

By Jena, Anand S, Das R. P

Leaching studies were carried out on Indian Ocean manganese nodules using sulphuric acid as the lixiviant. By leaching the nodules with 8 per cent sulphuric acid for 12h at 100°C, copper and nickel could be completely extracted along with 50 per cent cobalt and 6.2 per cent manganese.94.2 per cent of the iron was also dissolved. To increase manganese and cobalt extraction, charcoal was used as a reductant. The role of charcoal was to reduce the manganese dioxide and render it soluble as manganese sulphate as well as to facilitate solution of the cobalt minerals associated with the manganese dioxide. Various leaching parameters were studied including acid concentration, amount of reductant, leach time, pulp density and leach temperature. It was found that by leaching the nodules with 10 per cent sulphuric acid at 100°C for 4h using 5 wt/wt per cent charcoal (0.05g of charcoal per g of nodule) almost complete extraction of copper, nickel, cobalt and manganese could be achieved. However, under these conditions all the iron present in the nodules was also leached.

Jan 1, 1989

By Musa Karakus

In an attempt to explain the phenomena of lead entrainment during Cu drossing of lead bullion, two different synthetic lead bullions were heated to 1050°C, cooled slowly to various temperatures, and then quenched. The morphology and composition of dross particles that form when Mn is used to desulphurize bullion also were examined. Polished sections of these pyrometallurgical products were examined by process mineralogical techniques to identify the impurity phases, determine their chemical compositions, examine the morphology of the impurity phases and evaluate the potential for lead entrainment in such crystals, and characterize pre-quench and quench-generated phases. The phases crystallized were metallic lead, metallic copper, galena, chalcocite, albandite, Cu14.4Pb2S9. and 5.5Pb2S3.5. Metallic copper formed isometric skeletal crystals, chalcocite formed platy and skeletal crystals, and 1formed crystals and eutectic intergrowth with chalcocite and Cu14.4Pb2S9 or Cu5.5Ph2S3.5. The pre-quench crystals are larger and usually exhibit skeletal forms; the quench-generated phases are only a few micrometers across and disseminated throughout the lead matrix. Skeletal crystals of metallic copper and chalcocite form three dimensional networks that entrain large amounts of metallic lead.

Jan 1, 1989

By Charles L. Guild

I will add a few facts about the use and development of the Osterberg Test Load Cell and my association with Jorj. I first met Jorj in 1965 when the Guild Construction Co. drove 12" diameter cast-in-place shell piles for him at the Marquette Cement Co. in Nashville, Tennessee. When I met Jorj at the DFI Trustee's meeting in 1985 at Longboat Key, Florida, he showed me a sketch of his idea about using a test cell at the bottom of a caisson to test the end bearing and side friction on a caisson. He had made a successful trial test in Case International's equipment yard and wondered whether a similar device could be made for a driven pile. At first I was skeptical that it could be done but after thinking about it overnight I told him I felt it was feasible and we would do some work on it. At that time, there was a large bridge job going out for bid in Rhode Island using 14" square prestressed concrete piles'. Based on a record of the Guild Construction Co. Inc. driving over 3,000,000 feet of piling on work for the State of R.I., we felt we would have an excellent chance to be allowed to use them so we designed, detailed and fabricated three for 14" square prestressed concrete piles. As things worked out, we did not test them on this job and have not to date.

Jan 1, 1989

By Dennis A. Swyt

In current post-industrial America, U.S. manufacturing is undergoing major changes both in the technology of its production and in the size and composition of its workforce. At the same time that computers and robotics move the shop floor toward becoming the unmanned "factory of the future" [1], they increase the need within the overall production enterprise for new types of technicians and engineering professionals [2]. Based on previous works which examined, first, the evolution of the technology of manufacturing toward the flexibly-automated factory of the future and, second, the technical- professionalization of U.S. manufacturing sectors [1,3], this paper looks briefly at the workforce of the U.S. metals industry.

Jan 1, 1989

The theme of the conference is "excellence", an epithet of special significance in tertiary education. It appears in the mission statements, goals and plans to achieve them of most, and quite possibly all, tertiary institutions in Australia. In the context of excellence, this paper examines the current statue of professional education in the principal mining industry related discipline of Mining Engineering. It furthermore, identifies and discusses a number of special problems in mining education that the tertiary sector has long endured. Some of these problems are becoming acute, and solutions will have to be found soon in order for the industry to be assured of the supply of well motivated and appropriately qualified young engineers and scientists necessary to achieve and maintain the excellent to which it aspires.

Jan 1, 1989

By J. A. Gutierrez-Rodriguez, R. J. Purcell, F. F. ApIan

"Based on contact-angle measurements and the work of adhesion equation, the hydrophobicity of a wide variety of coals was found to decrease with decreasing rank, fixed carbon and total carbon content and with increasing oxygen and hydroxyl content. The estimated hydrophobicity, based on the water-sessile-drop contact angle, is '\.. 20% for lignite, increases with increasing rank up to a maximum of 'V70% for low (LV) and medium (MV) volatile bituminous coals and then decreases somewhat for anthracite. Using the captive-bubble technique, the calculated hydrophobicity ranges from '\.. 0% (below HV A bituminous rank) to a maximum of 55% for L V-MV coal. The former estimation is believed to be the more accurate. While the water-sessile-drop contact angle as measured on a polished-coal surface is usually larger than that shown by the captive-bubble method, the two values were found to converge at""' 95% relative humidity. It is proposed that the surface of coal consists of three kinds of sites: strongly hydrophobic, weakly hydrophobic and hydrophilic. The sessile-drop technique measures the total hydrophobic sites whereas the captive-bubble method measures only the more strongly hydrophobic sites. A water film covers the weakly hydrophobic sites preventing their detection by the captive-bubble technique.INTRODUCTIONCoal is a mixture of the degradation products of plants and of mineral matter. The appearance and properties of a specific coal is determined by the nature of the original vegetation and the extent of the physical and chemical changes which have occurred after deposition. The coalification process may be considered to have started with peat formation followed by a transition to lignite due to burial under sediments and metamorphic processes. Further metamorphic transformation to bituminous coals and, finally, under intense metamorphic action, to anthracite causes the carbon content and rank of the coal to increase. With such a wide variation in their genesis and composition, equally wide variations in the degree of hydrophobicity of different coals may be expected. It is the purpose of this paper to provide a means of estimating the hydrophobicity of a given coal sample based on rank parameters."

Jan 1, 1989

By John R. Turney

The success of the Mclaughlin acid pressure oxidatiun process has proved that a complex hydrometallurgical process can be an economically viable means of treating refractory gold ores. Homestake's Mclaughin acid pressure oxidation process was commissioned in August 1985 and ts currently operating at design tonnage of 3,000 tons per day. Mineralogical and process studies on the operating plant are discussed to show the improved understanding: of the process and its future applications. These studies are also compared with the initial process development work, thus illustrating the success of the initial scale up considerations.

Jan 1, 1989

By Michael J. Hannan, Thomas F. Torries

The nature of industry structure is examined and the structure of the aluminum, copper, lead and zinc industries are described by the use of factor analysis. Capacity is defined and the relationship between industry structure and capacity utilization is examined. It is demonstrated that excess capacity is possible in industries with competitive or monopolistic characteristics, but the effects of the overcapacity are vastly different in the two cases. In a competitive industry, cycles of overcapacity with attendant fluctuating prices are expected. A change in industry structure from monopolistic to competitive characteristics over time causes profits and economic rents to be transferred from the producer to consumers of the mineral.

Jan 1, 1989

By Russell B. Dix

Laboratory column leach tests are used routinely to evaluate gold and silver ores for heap leaching. The tests are fairly straightforward. The ore to be tested is placed into an appropriately sized leach column. Then an alkaline cyanide solution is applied to the ore and the effluent solutions are collected. The effluent solutions are then put through a column of activated carbon to recover the gold and silver in solution. Zinc precipitation may also be used for silver ores or if the ore contains a significant amount of soluble silver in addition to gold. The length of the leach time in the tests is mainly a function of how quickly the precious metals are recovered from the ore. At the completion of the tests, the tailings are assayed and the recoveries determined from the calculated head grades. The amount of ore to be used for a test is partly a function of its crushed size. The coarser the size, the larger the sample size for the column. A typical small-scale laboratory column test on ore crushed to -12 mm (-0.5 in.) would usually be conducted in a 100- to 150-mm-diam (4- to 6-in.-diam) column 2 m (6.6 ft) in height, containing about 20 to 45 kg (44 to 99 lb) of ore. A comparable test on the same ore crushed to 50 mm (2 in.) would be conducted in a 200- to 300-mm-diam (8- to 12-in.-diam) col¬umn 2 m (6.6 ft) in height, containing about 80 to 200 kg (176 to 441 lb) of ore. Larger-scale tests can be run by increasing the column heights and diameters. Conducting larger-scale tests results in increased costs for sample procurement, preparation, and running of the tests. The additional data obtained from

Jan 1, 1989

By H. G. Naidu, Raj K. Singhai, S. P. Singh

Introduction The economics of open-pit mining de¬pend heavily on the cost of overburden removal. It is necessary to maintain a pit slope as steep as possible. Steeper slopes lower the volume of overburden to be handled, thus lower the cost of material handling. There is, however, a limit to which the pit slopes in any given situation can be steepened. Steepening beyond this point could jeopardize the pitwall stability, ren¬dering it unsafe. It might even result in curtailment of pit production. Several factors affect the stability of pitwalls. Some are natural, such as topogra¬phy and regional and local geology. Others are man made, such as pit geometry, ground water management, equipment, drilling and blasting, and the type of excavation. Greater control can be exercised in the latter with proper planning and by following a set of procedures based on field experiences. This article deals with one such control¬lable factor - drilling and blasting. The eco¬nomics of steeper pit slopes is discussed, followed by a record of drilling and blasting practices in western Canadian surface mines. Microprocessor-based instrumentation and its application to blasthole drilling is also described. Economics of steeper pit slopes The economics of steeper pit slopes is not a new issue. It should be reinforced, though, that pit slopes must be as steep as possible to ensure maximum recovery of minerals at a minimum stripping ratio. For operating, economic, and safety reasons, different pit slopes are maintained during different phases of pit development. Figure 1 shows a hypothetical ore body, cylindrical shape, with a radius of 225 m (740 ft) and located 30 m (100 ft) beneath the surface. The mining operations are planned at two different slope angles of 25° and 40°. The ultimate pit depth was established on the basis of the criterion of "break even pit." The variation of the stripping ratio at differ¬ent mine levels is shown in Fig. 2. Table I summarizes the eco¬nomics involved for two pit slopes, 25° and 40°. Figure 3 presents the profits during the life of the mine for these two pit slopes. This study shows that steeper slopes for an open pit operation are far more advanta¬geous than flatter slopes. But, what is the optimum slope at any one point in the life of a moving pit? And how can the stable slopes be maintained over the short- and long-term? Canadian blasting practices A survey of blasting practices in western Canadian surface coal mines revealed that, at most mines, hard consolidated overburden is drilled and blasted. Blastholes are drilled with rotary crawler-¬mounted rigs using bits in the 220 to 310 mm-diam (8.5 to 12 in.-diam) range. Typi¬cal hole depths are 12 to 18 m (40 to 60 ft) to accommodate the pit bench heights of 12 to 15 m (40 to 50 ft). For a 12-m (40-ft) high bench, a typical hole will be 14.6 m (48 ft) deep including the subgrade drilling of 2.6 m (8.5 ft). Half of this hole will typically be a powder column and half will be stemmed. For a 15-m (50-ft) bench, a typical hole will be up to 18 m (66 ft) deep including the subgrade drilling. Drilling patterns are usually 9 m (29.5 ft) spacing and 9 m (29.5 ft) burden. De¬pending on local geology and hole diameter selected, drilling patterns of 8 x 8 m, 8.5 x 7.3 m, and staggered patterns of 11 x 5.5 m

Jan 1, 1989