Search Documents

By David Siu

Many problems were encountered with the mechanical wedge-type splices used for the 15-inch square precast prestressed concrete piles installed at an industrial plant site. Many of the wedges were breaking during installation of the splices and after pile driving resumed following splicing. Dynamic monitoring of the piles and uplift loading tests confirmed that the problems were associated with cracked or damaged wedges. More ductile, annealed wedges were subsequently used, and, while not completely satisfactory, they were found to perform better than the original more brittle wedges. Introduction Long precast prestressed concrete piles were installed to support heavy, settlement-sensitive structures at an industrial plant in Port Alberni, British Columbia, Canada. The piles were driven through soft compressible silts and clays to toe bearing in a dense sand and gravel deposit or on bedrock. Each pile consisted of two or three segments joined with mechanical wedge-type splices trademarked DYN-A-SPLICE. Shortly after construction began, problems arose during pile installation, and these problems were, later, identified to be related to the wedges, or clamps, used to connect the splice plates.

Jan 1, 1991

By David E. Siskind

In the early 1980's, the Bureau of Mines published four reports of structural response and damage from surface mine blasting, vibration monitoring, and analysis methods. These findings replaced simpler and less restrictive Bureau criteria dating back to 1962 for ground vibration and 1943 for airblast.

Jan 1, 1991

By Zhu Tonghao

A method of calculating anti-slide pile, sheet pile, underground diaphragm and structure with anchors etc. is proposeed in the paper. The effect of the various layers of soil, anchors and bracings etc. on laterally loaded structures may be considered in the model. In the analysis the structure is divided into a series of elements. The transfer matrices of both deformation and internal force are established for each element. According to continuous condition neighbouring element should be connected. Thus the deformation and internal force of each element can be found out in conbination with boundary conditions. The method has a wider adaptability and it can be applicable to a great variety of the analysis of interaction between various structure and soil. If parameters in model are selected properly, the computed results would be in good agreement with the measured data.

Jan 1, 1991

By Ed Coulter

Nevada has a population of 1.2 million people of which only 21% or 312,rIXl are native born Nevadans. he population between 1980-1990 grew a record of 389%. and ls the fastest growing state in the union. While only 2.5% of the total population are direct employees of the mining industry, excluding Reno and Las Vegas, one out of every three people living in Nevada work for a mining related industry.

Jan 1, 1991

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney's"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d'Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

In March 1990, Heritage Mining conducted a 2000 line km high resolution aeromagnetic survey of all its prospects in the Coromandel Peninsula. One of the areas covered was the Onemana Peninsula, situated about 5 km north of Whangamata. Details of location and geology are given by Robson and Stevens (this volume).   The detailed helicopter-borne magnetic and radiometric survey over the Onemana area consisted of 163 line kmÆs of flying, and was carried out in order to assist in the definition of hydrothermal alteration and pre- or post- mineralisation structures. The line spacing chosen was 100 m, flown east-west, with a mean sensor terrain clearance of 80 m. Tie lines were flown north-south every kilometre for levelling purposes. The sensor was a Geoinstruments G-813 proton precession magnetometer in a towed bird, with data recorded using a Geoinstruments G-2000 acquisition system.   The Onemana alteration system is at the northern end of a major north-north east trending structural corridor defined by regional aeromagnetic surveys performed by AMOCO in 1980 (Rabone, 1991). T his structure hosts a number of other extinct hydrothermal systems including Karangahake and Golden Cross. In the Onemana contour plot the predominant north-northeast structures form the boundaries of a large area of subdued magnetism in the southern part of the surveyed area that is caused by intense hydrothermal alteration. This area is about 3.5 km long by 1 km or more wide and contains outcropping sinters and hydrothermal eruption breccias, as described in Robson and Stevens. A number of other structures transect this alteration zone, with strike directions ranging from northwest to north. A northwest feature notably truncates the zone to the south, while the northern end seems to be simi1arly bounded; however as data coverage ends at the coast, this feature is less conclusive.    Two distinctive types of strongly magnetic rock were discernible the contoured data. The strong negative magnetic anomalies the north and west are caused by fresh negatively magnetised rhyolites. This was confirmed by ground follow-up work that showed the rocks to be fresh biotite rhyolites with high magnetic susceptibilities.

Jan 1, 1991

By W. K. Connor, O&apos

The Bureau of Mines is investigating the Co and Mn resource of the West-Central Arkansas District, including field investigations, mineralogical characterization, beneficiation, and hydrometallurgical tests. The deposits occur within the Ouachita Mountains and are con-trolled structurally, occurring along the axes of anticlines making up the mountain ridges. Brecciated novaculite is cemented with a mixture of Mn oxides, primarily cryptomelane and psilome-lane. Cobalt is concentrated within a particular Mn oxide phase, lithiophorite. Chemical analyses on head samples reported up to 25 pct Mn and 0.17 pct Co. Magnetic separation yielded products with up to 41 pct Mn and 0.22 pct Co at recoveries of 95 pct Mn and 93 pct Co.

Jan 1, 1991

By D. K. Steele

The U.S. Bureau of Mines has investigated the recovery of metals from copper industry wastes by sulfuric acid leaching in a semi-continuous, bench-scale system to solubilize arsenic, copper, and molybdenum. Leach residues contained approximately 40 wt pct PbSO4, suitable for processing at a lead smelter. Arsenic and molybdenum removal from leach solution was examined using solvent extraction with tri-n-butyl-phosphate (TBP), and copper was subsequently recovered by cementation. Bleed electrolyte from a copper refinery was determined to be a viable source of acid for the initial leach stage.

Jan 1, 1991

By G. Schuman

Variations in pyrite reactivity are known to exist within samples collected from different areas. Using samples collected from acid and non-acid sites, the relationship between the factors affecting pyrite oxidation and observed variations in pyrite reactivity was studied. Heavy liquid separations were used to extract the pyrite from nine pulverized rock, coal, and coal refuse samples. Simulated weathering tests were used to determine the degree of reactivity of the extracted pyritic material. Representative portions of each pyritic sample were analyzed for whole rock composition (including pyritic sulfur and neutralization potential), for elemental composition, and by x-ray diffractometry. The samples were also examined with reflected light microscopy to ascertain pyrite morphology distributions. Tests for the presence of iron-oxidizing bacteria were all negative indicating the leaching tests were conducted under abiotic conditions. The results of the simulated weathering tests permitted the partitioning of the samples into two groups based on positive or negative neutralization potential (NP) values. Determinations were then made to evaluate the degree to which a variety of factors, including temperature, partial pressure of oxygen and water, and crystallography affected pyrite reactivity. Multiple regression analyses showed no statistically significant relationship between degree of reactivity and elemental composition. However, for samples with negative NPs, a simple regression analysis showed a strong linear relationship to exist between the reactivity of the pyrite and the proportion of "unstable" pyrite (framboidal + mossy pitted) found in each extracted pyrite sample. Samples of pyrite with positive NPs, although producing acidity, did so in at least one order of magnitude less than the NP deficient samples, indicating the important role that NP plays in controlling pyrite reactivity. A simple linear regression between cumulative sulfate production and NP for the three samples with positive NPs had a correlation coefficient of 0.99. For the nine samples grouped together, a linear regression model between cumulative sulfate production and NP (both negative and positive) was established between log of sulfate and NP.

Jan 1, 1991

By Li Tiemin

It is one of important tasks in research of vibratory pile driving to increase speed of pile driving and depth of pile driving -- this means to increase capability of penetrating hard layer. In general, vibratory pile driving hammer make pile be situated in vibratory situation to drive pile by means of weight of hammer and pile, but the depth of pile driving and capability of penetrating layer are limited by dead weight of hammer. This paper introduces a new kind of vibratory pile driving hammer which differs from general ham­mer. A set of pressing system is attached to hammer and pile driving frame. The pull of winch installed on frame passing guide pulleys bring downwards press to pile through absorbing system of hammer. The practice and comparison test have showed that the new hammer is faster in pile driving and bigger in capability of penetrating layer than general one. Now, the vibratory pile driving hammer with pressing device has been applied widely in China. RESUME: The vibratory pile driving hammer based on vibratory principle to design have applied wide­ly in foundation engineering in many countries over the world. In order to suit the needs of deep foundation, at present, how can quicken speed of pile driving and increase depth of pile driving have become even more value to many countries in the world. This paper introduces a kind of rapid vibratory pile driving hammer which can drive pile deeper and more faster comparing with common vibratory pile driving hammer. Therefore, a kind of simple and reliable method has been offered for rapid vibratory pile driving in deep foundation.

Jan 1, 1991

By Leonard W. III Joseph, William H. Buttermore

Noise control is an important consideration in the design and operation of coal preparation plants. It is essential to understand and control noise sources to provide a safe environment for operating personnel. The average noise exposure levels in a typical coal preparation plant generally range between 95 and 100 db. An operator should not be exposed to noise levels of this magnitude for more than 4 and 2 hr, respectively, according to MSHA (Mine Safety and Health Administration) regulations. The major noise sources in a coal preparation plant include noise from impacting the inside surfaces of steel chutes, vibrating screens, coal crushers, pumps, motors, fans, and blowers. The magnitude of noise varies considerably from one situation to another. NOISE EXPOSURE IN COAL PREPARATION PLANTS Noise regulations established by the Occupational Safety and Health and- ministration (OSHA) are accepted by MSHA relative to coal preparation plants. Fig. 14-43 shows a graph of the time of noise exposure in hours per day to which a worker can be exposed for each A-weighted sound level. According to this graph, a worker is permitted to spend 8 hr in a 90-db noise environment, but that time must be halved when the A-weighted sound level increases 5 db. The noise dosage a worker receives is determined by the ratio of the length of time the worker spends in a particular noise environment divided by the length of time he is permitted to spend in that environment. If the worker is exposed to several different sound levels, his total dosage would be the sum of each of the individual dosages. The equation for determining the dosage is: where C is the actual duration of exposure at a given steady state noise level and T is the noise exposure limit for the level present during the time C According to MSHA regulations, the dosage, D, should not exceed one (1) for any worker for a full day of work. As an example of typical plant noise levels, vibratory screens and crushers emanate noise levels in excess of 90 db at a distance of 3 ft (0.9 m) with no material flow. With material flow, noise level increases 1 to 10 db depending

Jan 1, 1991

The Porgera Joint Venture commenced production during September 1990. A small tonnage underground mine extracts high grade gold ore using small scale stopes. Conventional drill and blast methods are used for development and production mining. Ground support is effected with Splitset anchors, grouted rebar bolts and grouted cable bolts. Splitsets and grouted rebar can be installed by mechanised means. Vertical crater retreat, slot and massfire, and modified VCR stoping tech- niques are used at Porgera. Stopes are backfilled with a relatively strong cemented rockf ill. Future stope sequences require recovery of pillars beside and under filled stopes.

Jan 1, 1991

By William K. Connor, O&apos

The U.S. Bureau of Mines (USBM), in cooperation with the American Society of Mechanical Engineers (ASME), conducted over 200 hours of melting tests to vitrify residues from five municipal waste combustion facilities. Combined residues (grate residue and f1yash) from three municipal waste combustors, a waste water treatment sludge combustor, and flyash from a refuse-derived-fuel (RDF) boiler, were sequentially melted in a I-metric-ton (mt) water-cooled-wall electric arc furnace. Each of the residues underwent magnetic separation, screen size analysis, and bulk chemical analysis prior to melting. The furnace products were examined by optical and electron microscopy and by X-ray diffraction. Bulk chemical analyses were acquired for the metal, fume, and vitrified furnace products. The material balance for the furnace operation indicates that from 69 to 86 pct of the feed reported to the vitrified furnace product, which had leaching potentials well below the EPA limit for each metal, as determined by the EPA TCLP. The electric arc melting furnace currently is being utilized in a cooperative research project between the USBM and the Idaho National Engineering 'Laboratory (INEL) for melting tests on simulated low-level radioactive wastes,

Jan 1, 1991

Mt Waruwari, host to the Porgera underground gold mine in the Highlands of Papua New Guinea (PNG), is a prominent ridge of sediments and dioritic intrusives rising approximately 600m above the surrounding valley floor. Consequently, mining occurs in a low stress environment where structural and material considerations are foremost in the design of ground support and reinforcement. Three major rock types are encountered in the underground mine. These are locally referred to as "black sediments" (slightly indurated mudstones and clayey siltstones), "altered sediments" (derived from black sediments by thermal metamorphism), and "intrusives" of dioritic composition. The rocks are moderately to highly fractured, the black sediments being generally weak and occasionally sheared while the altered sediments and intrusives are quite strong but often brittle. Mining takes place from a series of stopes extracted by either slot and mass blast or a modified vertical crater retreat method (VCR), which are backfilled with a cemented rock fill. Ground support and reinforcement has been relatively conserv- ative to date and generally relies on pattern reinforcement of all development with cement grouted "rebar" bolts and mesh, extending to pattern cable bolting with occasional mesh in stope backs. In addition there has been considerable reinforcement of stope hangingwalls in some cases. A programme of broad scale structural mapping, monitoring with extensometers, material property testing, and stress analysis has been devised to allow optimum design of ground support and reinforcement in the future. Considerable work remains to ,omplete this task.

Jan 1, 1991

By M. Kalin

"Ecological Engineering and Biological Polishing technology is a decommissioning approach for inactive coal, uranium and base metal operations. To improve acid mine drainage water some fundamental aspects of wetland ecology and sediment microbiology are combined, to provide conditions to allow for biomineralization of the contaminants.This paper summarizes the first records of microbial alkalinity generation in acid mine drainage through the utilisation of the ARUM process. The process requires that the seepage is at pH 4.5 where sulphate reducers utilize sulphate to produce hydrogen sulphide, which in turn precipitates with metals. The pH increase is brought about by alkalinity generating microbes.The ARUM process has been successful in increasing the pH from 2.5 to 7.0. Flow through reactors operated in the laboratory continuously for more than 60 days have removed Ni from 13 mg/L to < 0.01 mg/L. Design parameters are being developed for low flow rates of 5 L/min in a test system receiving seepage from a tailings.1.0 INTRODUCTIONAcid mine drainage associated with mining wastes poses a significant environmental problem. Conventional means to treat acid mine drainage (AMD) use chemical treatment system. Ecological Engineering technology uses natural biological means to curtail and ameliorate AMD during mine operations and at the time of decommissioning. The premise underlying Ecological Engineering technology is that AMD is the result of a natural process enhanced by mining activities. Therefore, in nature, a process providing a natural balance to AMD has to exist, which, when assisted through appropriate means, can counteract the detrimental effects of AMD on the environment. This process is microbial alkalinity generation which is known to occur in wetlands, lake and ocean sediments (Baas Becling et al, 1960)."

Jan 1, 1991

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through the use of more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the air bubbles, water, and ore, rapidly attaching the hydrophobic mineral to the bubble surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. A rougher concentrate containing 4.5 pct copper was obtained from a western porphyry copper ore containing 0.67 pct copper. Over 99 pct copper was recovered from the ore at a rate 7 times faster than conventional flotation.

Jan 1, 1991

By Yu Zhenquan

At the construction site of Bao Shan Iron &. Steel Mill in Shanghai, lots of RC driven piles with length of 50 to 60m were applied. The most unfavourable distribution of stress along the pile shaft was known by measuring the compressive and tensive stresses. With analysing the test results a phenomenon of impact fatigue of RC pile was discovered, the range of impact fatigue and its critical zone can be distinguished. Finally some countermeasures are presented to avoid the impact fatigue of RC long pile.

Jan 1, 1991

By J. Parker

Gentlemen; Rainy day in Upper Michigan, a good time to catch up on reading. Am doing that, and have a couple of questions concerning the K and P paper on roof problems and supports. I wonder if the authors can enlighten me. The compressive strength of the coal was reported as 4.4 MPa (633 psi) and compressive stresses measured in the coal seam were reported at around 27.6 and 48.2 MPa (4000 and 7000 psi ). Can such a soft coal actually contain such a high level of stress? Can it be measured as if the material were elastic, or does the coal behave plastically? Can that stress level be confirmed with hydraulic load cells? And if the coal is so soft, and if it is plastic, why is the stress field not hydrostatic? The intact roofrock appears to be unusually strong, with compressive strength reported at around 145 MPa (21,000 psi), and some failures were noted as soon as the rock was exposed. Were tests run to find out how that rock responded to the addition

Jan 1, 1991

By M. P. Ahola

This U.S. Bureau of Mines report presents an overview of the use of three unique numerical modeling methods to analyze cutter roof problems in underground coal mines. Cutter roof failures are common in coal mines where the immediate roof is comprised of thin laminae exposed to highly biaxial tectonic stress fields. The predominant mechanism for failure is assumed to be excessive shear stress at the entry corners exceeding the shear strength of the rock. Early work in this area utilized the finite-element method and then the boundary-element method to analyze several cutter roof control measures. Various stress control measures were simulated to estimate their respective effects on reducing the high levels of shear stress at the entry corners. More recent studies made use of the discrete-element method. This method was used to take the analyses beyond the elastic continuum limits to simulate the propagation of a shear fracture and subsequent redistribution of stress within the mine roof. A simple roof bolt model was implemented to show the benefits of bolting to increase the resistance to shearing and separation along horizontal bedding planes and maintain roof stability.

Jan 1, 1991

Develop an improved downhole geophone system with enhanced signal/noise ratio for collecting cross-hole seismic data used in tomographic reconstructions. Background The Bureau of Mines is conducting research in the use of cross-hole seismic tomography for detecting and monitoring leach solution flow during in situ mining. This technique requires the use of a downhole seismic energy source in one borehole and a downhole wall-locking receiver (geophone) in another borehole separated from the first by the region to be investigated. Bureau research personnel chose a commercially available air gun for use as the downhole seismic energy source. Unfortunately, commercially available downhole wall-locking geophones that the Bureau tested were difficult to operate in the field, often unreliable and generally inadequate in terms of their signal/noise ratio. Therefore, research personnel began to experiment with an alternative down-hole geophone design that could be used to collect adequate data in a wide variety of borehole and cross-hole field situations. Approach An attractive alternative geophone design would be one that would incorporate a pneumatically operated wall-locking system. As an integral part of the Bureau&apos;s existing field system, a portable, high- pressure/low-volume air compressor would have sufficient capacity to operate the air gun as well as several small high-pressure pneumatic linear actuators. This approach was the simplest and most compatible with the research activities being conducted at the site.

Jan 1, 1991