Search Documents

By James V. Errico

On October 1, 1993 the regulations for assessing and cleaning up contaminated soil and groundwater in the Commonwealth of Massachusetts were revised. These new regulations, known as the Massachusetts Contingency Plan (MCP) 310 CMR 40.0000, were developed to keep routine releases out of the regulatory system and rely on private parties to handle most releases without Department of Environmental Protection (DEP) oversight. An integral part of the new MCP is the Licensed Site Professional (LSP). An LSP is required to handle activities and render opinions once a site enters the MCP. These regulations must be adhered to where ever a release has occurred, including construction sites. A brief overview of the new MCP is given below; see attached MCP Flowchart for graphical summary. Entering the MCP Process A release of oil or hazardous material (OHM) to the soil or groundwater above applicable reportable quantities (RQ's) or reportable concentrations (RC's) will require notification to the DEP and compliance with applicable provisions of the MCP. RQ's and RC's are listed in the MCP (310 CMR 40.1600) for most compounds that are typically encountered. For each compound there are two RC's for soil (S-1 and S-2) and two for groundwater (GW-1 and GW-2). The S-1 and GW-1 RC's apply to sites that are environmentally more sensitive, as a result they are lower than the S-2 and GW-2 RC's.

Jan 1, 1994

By G. Vallebuona

Currently, empirical models are used for predicting the hydrocyclone performance in terms of capacity, cut size (d50,c), water split and partition curve. These models, for example those of Lynch and Plitt, have been developed and checked for hydro cyclones with diameters larger than four inches. For smaller diameter hydrocyclones little empirical modelling has been done. This paper reports extended experimental research on small hydrocyclones. For these cyclones, the suitability of existing empirical models has been checked and their accuracy compared. Modifications of the existing models equations are proposed, improving their predictive capability for the small cyclones performance.

Jan 1, 1994

By A B. Christie

Space-based synthetic aperture radar (SAR) data is becoming available over much of the world, includingNew Zealand. Radar imagery has a number of very advantageous features, including all-weather capability; it also has artifacts, such as layover, which require processing before these data may be used to best effect.   This paper gives an outline of SAR, details the image processing required, and discusses the use of the first New Zealand Japan Earth Resources-1 SAR data to aid geological mapping on the Coromandel Peninsula.

Jan 1, 1994

By Richard E. Danell

"Blasting is a principal step in the surface mining process for breaking and, in the case of overburdencasting, moving rocks and minerals. As many surface mines are coming to the end of theiroperational life, blasting can once again play an important role through the earthmoving operationsrequired to rehabilitate the minesite. Since blasting is such an energetic and destructive process, itis difficult initially to envisage its use in rehabilitation. However, blasting has found applications inmany civil engineering projects aimed at rehabilitation, including well digging, channelling and soilcompaction. For surface mine rehabilitation, the main purpose of earthmoving operations is toproduce a stable landfonn that will sustain revegetation. In particular, blasting can be applied toreducing the slope of steep walls left by quarrying and open pit mining through a modified form ofthe overburden casting technique. Blasting can also be applied to breaking up pit floors andbenches to speed and improve revegetation of these areas (subsoiling)."

Jan 1, 1994

By James R. Hindman

Vermiculite is the mineralogical name generally applied to a group of hydrated, trioctahedral ferromagnesian aluminum platty or micaceous silicate minerals. In microscopic particles the mineral as mineral is differentiated from montmorillonite by a higher Si:AI ratio of approximately 3:l and a higher layer charge and higher cation exchange capacities. Commercial vermiculite, the vermiculite which is mined, beneficiated, and discussed in this chapter, is an important industrial mineral which is formed by the alteration of macroscopic particles of biotite and iron-bearing phlogopite. In natural form it has the size and shape of mica, while possessing the ion exchangeable properties of zeolites and some clays. Within the internal structure of vermiculite lie water molecules, which when rapidly heated to high temperature, transform into steam causing the vermiculite particles to increase in volume. This process of thermal exfoliation produces a lightweight product which finds use in various construction products, agriculture, horticulture, and other industrial applications. In exfoliated form it has the low density and biological inertness of expanded perlite, while maintaining a chemically active surface. Most of the uses of vermiculite are for the thermally exfoliated material. In addition, the cation exchange potential of vermiculite and its layer-silicate structure are properties which can be used as the basis for numerous products including intumescent coatings and gaskets, inorganic films, and the treatment of nuclear and other toxic waste. When chemically and physically modified, it possesses some properties common to organoclays and synthetic compounds. In high purity concentrates and manufactured products, these properties can be altered and optimized in applications to produce superior performance. GEOLOGY Mineralogy Vermiculite was first described as a mineral by Thomas H. Webb in 1824. Webb believed vermiculite to be a variety of talc and described its diagnostic property of thermal exfoliation thusly: "If subjected to the flame of a blowpipe, or that of a common lamp, it expands and shoots out into a variety of fanciful forms, resembling most generally small worms having the vermicular motion exact." Observing that with one exception, all commercial vermiculite has formed by the alteration of iron-bearing phlogopite, a simple definition of vermiculite might be the alteration product of trioctahedral micas, macroscopic particles of which display marked exfoliation when heated rapidly to temperatures above 374°C (the critical temperature of water). The first vermiculite described was found near Worcester, MA, but it was later pointed out by Brush (1866) that vermiculite had been known for some time in Japan as a children's novelty. Because the techniques for mineral analysis were somewhat primitive com- pared to those routinely available today, and because the structure and crystal chemistry of the micas and related minerals were not widely understood, the early literature generated at least 20 "new" minerals which were nothing more than variations in the color and chemistry displayed by vermiculite. Trade names such as Dugarlite, Mandolitem, Strong-LiteTM, and Zonolitem are sometimes used to denote commercial vermiculite, thermally exfoliated vermiculite and their products. Vermiculite particles resemble mica and vary in color from colorless through tan and green to black, depending on the chemical composition. Most physical and optical properties are close to those of biotite, with perfect basal cleavage, hardness between 1.5 and 2.5 Mohs, and specific gravity between 2.2 to 2.8. Fine-sized particles will feel talcose, especially when wet. However, for commercial vermiculite the diagnostic test is that of thermal exfoliation. Vermiculite can display a wide range of compositions, depending on the composition of the original mica and the change of chemistry during weathering and ion exchange. Chemical data for some commercial vermiculites are given in [Table 1]. There are numerous analyses for vermiculite given in the literature, and the analyses of vermiculites from commercial deposits will fall within the range indicated by the average analysis in the table. Many analyses separate the adsorbed water (H2OP) from crystalline water and water as hydroxyl (H20+). The basis of separation of adsorbed water is generally considered to be 100°C. However, hydrate water within the vermiculite interlayer begins to be lost at 75°C and lower. Therefore, measured water content and loss on ignition are combined in the table as H20[total].

Jan 1, 1994

By R L. Brathwaite

The mesothermal quartz-scheelite lodes of the Wakamarina valley are one of twelve known mined or prospected gold-bearing areas in the Marlborough Schist. Recorded production was 556 kg gold, a little silver, and c. 390 t scheelite. 134 m of the 1800 m long Golden Bar reef are accessible in the No 2 level of the Golden Bar mine. The reef is a typical multi-banded mesothermal vein, mostly c. 1.75 m wide, enclosing narrow horses of schist country rock. Scheelite is sparsely distributed, and is more common in small veinlets in the hanging wall schist. The country rocks are textural zone I-1m schists of prehnite-pumpellyite to pumpellyite-actinolite metamorphic facies. Their geochemistry suggests they are part of the Caples Terrane, and of calc-alkaline volcanogenic arc origin. The associated Wakamarina Quartzite is strongly recumbent folded, and of the same metamorphic grade, with abundant pumpellyite, stilpnomelane, and garnet, presumably spessartine. Although it has geochemical signatures of a deep sea sediment, it is depleted in Cr and Cu, and greatly enhanced in K and Ti, when compared with a standard chert. It also has trace element characteristics of a calc-alkaline arc-related sediment. However, associated greenschist has MORB-like incompatible element chemistry. The Golden Bar reef lies within a steeply dipping, normal to transtensional dip-slip fault adjacent to a shallow-dipping mylonite shear zone, which, at least on the footwall side, is 040 m wide. The shear foliation has been severely dragged down to nearly parallel the Golden Bar reef within 1 m of the quartz lode. Preliminary structural analysis suggests that the shear zone is extensional. X-ray diffraction analyses of the wall rocks show a progressive depletion of amphibole, stilpnomelane, and pumpellyite towards the reef, and enhanced illite/muscovite and Kfeldspar adjacent to the lode, along with possible graphitic carbon within 10m. Two zones of intense quartz veining occur, one adjacent to the hanging wall for 12 m and one from 40 m outwards. Quartz vein systems in the country rock are complex and span from pre-schistosity to post-mylonite. They include multiple generations of quartz, actinolite, stilpnomelane, pumpellyite, albite, adularia, chlorites, illite/muscovite, calcite, and scheelite. Metal analyses across the Golden Bar reef showed gold values of 0.13.1 ppm, and low tungsten values, consistent with the observed sporadic scheelite occurrences. As and Sb are at background levels, but enhanced Cr (150 - 430 ppm) relative to the schists (30 - 41 ppm) suggests that the source hydrothermal fluids passed through and leached mafic to ultramafic rocks.

Jan 1, 1994

In this U.S. Bureau of Mines report, two drill-split mechanical excavation mining system concepts are described, casted, and cost compared with conventional drill-blast mining systems. The concepts for the two drill-split mechanical excavation mining systems presented are (1) a method for steeply dipping narrow veins 0.6 to 1.2 m wide and (2) a longwall method for fiat-lying tabular ores. In the proposed systems, 70 to 80 pet of the ore is disposed of underground as backfill. For sortable ores, face area crushing, sorting, and direct stowage of run-of-mine waste and low-grade ores are proposed. The underground sorting and stowing of waste reduce materials handling, processing, and waste disposal costs by reducing the quality of ore transported to the surface by 70 to 80 pet (by volume). Because many of the tools and techniques proposed for use in these systems have little or no historical mining industry use, cost assignations are heavily influenced by engineering judgments and presented as prefeasibility-level cost estimates. These estimates, presented as discounted-cash-flow-rate-of-return (DCFROR) values, show the proposed systems to be at least as profitable as, and in some cases 50 pet more profitable than, conventional drill-blast mining.

Jan 1, 1994

By Burford B. D, Johnson N. W, Rohner P

Under design philosophy, the Hilton concentrator produced lead, zinc and LGM (lead plus zinc) concentrates. The LGM (Iow grade middling) concentrate was produced by combining coarse middling streams from the lead and zinc circuits, regrinding and subsequent flotation. Mineralogical examination of the zinc circuit middling stream prior to regrinding suggested that production of zinc concentrate from the zinc circuit middling stream should be possible by rearranging existing plant equipment. Laboratory testing of samples of plant products, however, showed that regrinding combined wi th the usual reagent suite was nO1 sufficient to produce a zinc concentrate of the required specifications.Examination of the process water highlighted a problem with dissolved salts in the circuit water, which was solved by in-circuit precipitation of the dissolved ions with soda ash. Implementation of the procedure in the concentrator effectively transferred to the zinc concentrate all sphalerite previously recovered to the LGM concentrate.

Jan 1, 1994

By Graham Davis

The future of the world's minerals industries is often painted as bleak. Peter Drucker has repeatedly proposed that the demand for minerals has become "uncoupled" from world economic growth.' This implies that, while mineral demand was in the past linked to the growing demand for and consumption of goods and services, further world development will not require substantial mineral inputs. Lester Thurow noted that for these reasons the US minerals industry is diminishing in scale and economic importance.2 There is some documented evidence of such uncoupling, and the demand for minerals may indeed diminish in the future. But such announcements are, to this point, no more than speculation. For instance, is it not just as likely that renewed environmental concerns will cause increased demand for the relatively innocuous environmental properties of metals, replacing plastics? And even if the prophesied demand decreases do occur, a sufficient fall in metal prices due to technological advances could increase the quantity of minerals demanded above current levels, in spite of leftward shifting demand curves. Thus, worldwide mineral production activity may increase or decrease in the future and no one can say whether more or fewer of the earth's citizens will become involved in the extraction and processing of minerals.

Jan 1, 1994

By Suresh K. Bhatt

Although overall worker productivity for U.S. underground coal mines is available, productivity by mining method and seam thickness is not. Mining technology has gone through dramatic changes in the past decade, and the industry has experienced a lack of accurate productivity Figures addressing these changes. This information is of great interest in planning for future mining systems as thick and shallow coal seams currently being mined are depleted and exploitation of thinner, deeper, and better quality seams is considered to partially meet the requirements of the 1990 Clean Air Act Amendments. In a cooperative program, the U.S. Bureau of Mines obtained raw mine level production and related data from U.S. Energy Information Administration for 1989 and 1990 and performed the needed statistical analysis. Base criteria, parameters, and salient results of the mine productivity analysis are presented in this report.

Jan 1, 1994

By Bengt H. Fellenius

Session 2, Deep Foundation without Soil Excavation, has attracted no fewer than 22 papers dealing with subjects from soil improvement by grouting, injection, and deep mixing techniques through vibroflotation and special piles, including aspects pertaining to conventional driven and bored piles. In the short time available, it is not possible to both do justice to the papers and provide a critical review of the state-of-the-art. Instead, to meet the objective of making the next half hour worthwhile to the audience, I have chosen to comment on a few special points brought forward in the papers and thereafter to discuss more in detail a couple of aspects I have deemed to be of general interest. Four papers deal with jet-grouting, injection, and deep mixing techniques: DOMSKI, J. J. Reinforcement of subsoil under the foundations of historical buildings in Cracow using deep injection technique. RESTELLI, A. B, BERTERO, M., and LODIGIANI, E. Deep mixing technology to improve the bearing capacity of a very soft clayey soil under an earth embankment.

Jan 1, 1994

By R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. This paper presents the findings of on-going testing of various sizes and shapes of grinding media. Plant observations combined with estimated breakage rates demonstrate the importance of appropriate selection of media sizes on the milling operation.IntroductionBrunswick Mining and Smelting is located near Bathurst, New Brunswick, and operates one of the world's largest lead and zinc mines. The ore mineralogy and processing flowsheet have been described elsewhere (Petruk and Schnarr, 1981; Shannon et 01., 1993). Despite the 25 years' milling experience, there has been considerable disagreement as to the required grind size (Grant et 01., 1991). Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37 um) and averaged slightly above 71% in 1992. Results from mineralogical analysis (Petruk and Schnarr, 1981), laboratory and pilot plant experiments, as well as plant sampling (Grant et al., 1991; Hendriks and Ounpuu, 1985; Shannon et al., 1993) indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15 urn to 25 um range.This paper shows the results obtained so far from the evaluation of the effect of grinding media size and shape on grinding mill efficiency. The problem of finding optimum grinding media size, shape and composition has been recogrtized since the early 19405. The main criterion for the selection of media size is the size of the material to be ground (Bond, 1958). Although several relationships have been proposed to assist in the selection of grinding media size, none of them are entirely satisfactory (Wills, 1988). Other approaches using the breakage rates and process simulators were developed to help in the selection of grinding media size (Austin et al., 1976; Lo and Herbst, 1986; Concha et 01., 1992; Samskog et al., 1990; Martinovic et al., 1990). Although considerable effort was put into the analysis of grinding media size, very little information is available on the effect of grinding media shape (Norman and Decker, 1985, p. 3C-4). Norris (1952), Kelsall et al. (1973) and Herbst and Lo (1989) have shown that balls are more efficient than other shapes of grinding media including truncated cones and cubes."

Jan 1, 1994

Amercable, Inc. Andalex Resources, Inc. ARCO Coal Company Behre Dolbear & Company, Inc. Colowyo Coal Co. L.P. Continental Conveyor & Equipment Company Crane & Hoist Sales Crested Butte Mountain Resort Cyprus Amax Coal Co. Energy West Mining Company The Falkirk Mining Company Fleischli Oil Co. Inc. Halbach & Braun Industries Hemscheidt Corporation GH Henley Industries Ingersoll-Rand Co. Jennmar Corporation Joy Technologies, Inc. K & P Sales Engineers, Inc. Kennametal, Inc. Kerr-McGee Coal Corporation L & H Welding & Machine Co. McLanahan Corporation National Coal Association The North American Coal Corporation Northwestern Resources Company Peabody Western Coal Company Phillips Machine Service Pincock Allen & Holt Ramsey Technology, Inc. Rust Tractor Company Salt River Project Schroeder Industries Stamler Corporation TerraMatrix TIC (The Industrial Company Wyoming, Inc.) Trapper Mining Inc. Wagner Equipment Company Western Energy Company Wheeler Machinery Company

Jan 1, 1994

By L. L. M. Kadnuck

The U. S. Bureau of Mines studied the suitability of using flexible tendon cable supports as secondary roof supports at a western coal mine. The supports were installed in longwall tailgate entries and grouted into the mine roof. This paper quantifies how the use of cable supports can improve ventilation in underground airways. A mine ventilation simulator was used to model the changes in airway resistance and airflow and show potential for further ventilation improvements when cable supports are used. Model results indicated that cable support use translated to savings in air pressure around the longwall panel and increased airflow at the longwall face.

Jan 1, 1994

By M. Misra, I. A. H. Schneider

The flocculation of -38 pm calcite, hematite and kaolinite aqueous suspensions by the yeast Candida parapsilosis and products derived from rupture of the microorganism was studied. Flocculation of hematite suspensions by the microorganism and its derivatives readily takes place between pH 2.8 and 11.4. Maximum flocculation occurs at about pH 6.5. Flocculation of calcite suspensions by the microorganism and its derivatives readily takes place between pH 7.0 and 11.8. Maximum flocculation occurs at about pH 10.0. Flocculation of kaolinite suspensions was less than that for the other two minerals. However, a soluble fraction derived from the rupture of the organism functioned as a good flocculant for the mineral, albeit at an increased concentration, between pH 2.6 and 11.5. Maximum flocculation occurs between pH 6.8 and 7.2. An attempt is made to relate the behavior of the various systems to the surface characteristics of the minerals and the surface and chemical properties of microorganism and its derivatives. Experimentation used to evaluate the flocculation includes actual flocculation tests, microelectrophoresis measurements and scanning electron microscopy.

Jan 1, 1994

By A. C. Wadhawan

In the present context of rapid industrialization, production of Lead-Zinc metals from low grade materials, residues and wastes can make substantial contribution to the supply of these metals in India. Recovery from secondary sources also plays an important role in conservation of mineral resources and lower power consumption. Conscious effort is therefore, required to increase the secondary metals which, besides saving in energy cost will also help in waste material management and keeping environment clean. The major thrust is, therefore, needed in this direction. During all these years, the Indian Lead- Zinc industry has made sustained efforts for recovery of metals from low grade ores and from metallurgical wastes and residues. The paper identifies the treatment of low grade ores by various technologies and techniques and the treatment of metallurgical residues and wastes generated during primary Lead and Zinc smelting in India. Some of the major achievements in past decade have also been elaborated in the paper. The strategies to be followed for continuing treatment of low grade ores and waste materials by adopting newer, environmental friendly technologies, in consonance with the rigid standards being adopted by most of the countries including India. have also been dealt with in the paper.

Jan 1, 1994

By Vinod K. Sikka, René Cooper

"Cohoes, New York 12047 Intermetallics are an attractive class of advanced materials. The aluminide intermetallics offer advantages including: (1) lower density, (2) oxidation resistance, (3) carburization resistance, and (4) interesting mechanical properties because of their ordered crystal structure. Even though the attractive properties of the aluminides and other intermetallics have been known for nearly four decades, their practical applications have not been developed for two reasons: (1) the poor ductility (in some cases, both ambient and high temperatures) and (2) the lack of processability into meaningful components. Recent advances such as ductilization of Ni3Al by small additions of boron and the knowledge that environmental effects are the major cause of poor ductility in Fe3Al and FeAl systems have brought the intelmetallics into the forefront of research and their commercial applications. This paper has described a method for melting Ni3AI-based alloys that successfully utilize the exotherrn for the formation of NiAl from the elemental materials. The reaction-synthesis method has also been utilized for the production of NiAI and NiAI-based alloy powders from the elemental powders. The reaction-synthesized powders of NiAI and NiAI-based alloys were consolidated by hot extrusion and evaluated for tensile properties over a temperature range from room temperature to 1050ºC. The powder-processing conditions have been found to have more influence on the ductile-to-brittle transition temperature of NiAI than the powder-production method.IntroductionIntermetallics are an attractive class of advanced materials [1-11]. The alum in ide interrnetallics offer advantages including: (1) lower density, (2) oxidation resistance, (3) carburization resistance, and (4) interesting mechanical properties because of their ordered crystal structure. Even though the attractive properties of the aluminides and other interrnetallics have been known for nearly four decades, their practical applications have not been developed for two reasons: (I) the poor ductility (in some cases, both ambient and high temperatures) and (2) the lack of processability into meaningful components. Recent advances such as ductilization of Ni3Al by small additions of boron and the knowledge that environmental effects are the major cause of poor ductility in Fe3Al and FeAl systems have brought the intermetallics into the forefront of research and their commercial applications. The paper will briefly review the processing techniques being pursued for the commercial applications of Ni3Al-based intermetallics. The major emphasis of the paper will deal with synthesis of Ni3Al and NiAI intelmetallics."

Jan 1, 1994

Abouleid,A.F.327 Ajdic, I.451 Albert, L.F. 221,307 Alem, A. 525 Asama, T. 431 Avgherinos, P. J. 373 Baker Jr, C.N. 331 Balossi Restelli, A. 171 Beckwith,G.H.33 Bellini, A. 469 Bermingham, P. 481 Bertero,M. 171,535 Beyer, M. 503 Bottiau, M.41 Botto, G. 205 Bruskeland, O. 337 Budhu, M. 349 Bullivant, R.A. 181 Bustamante, M.G. 185, 475, 535

Jan 1, 1994

By Liane L. M. Kacinuck

This U.S. Bureau of Mines publication is intended to provide mining industry representatives and regulatory authorities with a reference package dealing with studies on hydrology and underground mine subsidence. An annotated bibliography and a list of additional sources are given and represent references published prior to June 1993. Ninety-two references ware identified and 72 obtained for assessment. Annotating the references included evaluating the study methodology and summarizing the basic results. The references are also compiled based on geographic location to aid the user in identifying articles of particular interest.

Jan 1, 1994

The knowledge of aggregate size under various chemical and hydrodynamic conditions is very important for selective agglomeration, flotation and water clarification processes. Traditionally, aggregate size measurements are conducted using an ex-situ technique or in a diluted suspension. In either case, the measurement occurs in an environment that does not resemble the actual conditions under which the aggregates are formed. In this study, an on-line scanning laser microscope has been used to study the coagula size of micronized coal suspensions as a function of pH, solids concentration and agitation intensity. A maximum aggregate size of 310 µ m was obtained under relatively quiescent conditions and at pH values near the iso-electric point (iep) of the coal. The aggregate size results compare well with the coagulation efficiency measurements obtained under the same pH conditions.

Jan 1, 1994