Search Documents

By E. Tondu

Separation Technologies Inc.’s (STI) electrostatic separation technology is a dry, continuous process for the separation of discrete particles. This high-volume process does not require any additives nor is any additional waste produced. In December 1993, STI, in cooperation with New England Power(NEP), installed an 18-t/h (20-stph) prototype electrostatic separator at NEP’s Salem Harbor plant. The plan was to convert waste streams of type F fly ash into commercially valuable products. In July 1995, a second separator was installed at NEP’s Brayton Pointplant. Fly ash feed, ranging from 6% to 25% carbon (loss-of-ignition fly ash or LOI), is separated into <3% LOI “clean” ash and sold as a portland cement substitute in the New England concrete markets.

Jan 1, 1996

By F. N. Voskoboyev

The suggested new method for control of geomechanical state of undermined rock mass ensures, as a safety measure for the earth surface protection, the decrease of deformations by 2,5 - 10 times in mining the single seam, and by 1,5 - 5 times - in mining bed series, i. e. approximately within the seam ranges as in the application of full packing with various compressive properties or partial extraction of resources over the area with different coefficients of extraction. It should be noted that this new method has the following advantages o\w rhr. conventional methods: a) the decrease of the packing area and packing works volume by 2 - 4 fold including the operating and productive expenses; b) the elimination of mineral losses due to the increase of extraction coefficient up to 100 5%; c) rock utilization from workings drivage by its placing in the mined - out space. Perspective field of application of this method: disconservation of mineral resources in the left protective pillars of various designation.

Jan 1, 1996

INTRODUCTION ò World coal production, Exporters and Importers òNew Zealand Exports, Markets and Products ò Types of Markets and Price Setting ò Bench Mark Prices and Exchange Rate ò Transport ò International Marketing - Key Factors ò Coal New Zealand , the Challenges

Jan 1, 1996

By Scott G. Honan, Wayne F. Luinstra

"Since 1992, the concentration of gold using gravity methods has progressed to become an important part of production at Hemlo Gold's Golden Giant Mine. Currently, the gravity circuit accounts for approximately 25% of the Golden Giant Mine's Gold production. This circuit consists of a 30 inch Center-Drain Knelson Concentrator and a Shaking Table. The evolution of gravity concentration will be discussed with an emphasis on the economic justification for a gravity circuit as well as the practical aspects and metallurgical impact of operating such a circuit. It will be demonstrated that the operation of a gravity circuit has definite benefits to the operation of the Golden Giant Mill and will continue to play an important role in future gold production.1.0 IntroductionHemlo Gold Mines Inc. Golden Giant Mine is a 3000 TPD underground gold mine and milling facility located 40 km east of Marathon, Ontario. Mining is accomplished by means of sublevel longhole open stoping. The ore is processed using conventional crushing, 3-stage ball milling, conventional cyanidation and CIP processes. The mill and concentrator are described in more detail in other publications1,2.Since July of 1992, the Golden Giant Mine has been using a gravity circuit for gold recovery in the mill's grinding circuit. Despite the fact that gold recovery averages over 96% using conventional cyanidation and carbon-in-pulp processes, the gravity circuit has become an integral part of milling operations. This paper will discuss the economic justification for a gravity circuit as well as the practical and metallurgical aspects of its operation."

Jan 1, 1996

By Kafui Nyavor

The indirect, and the direct contact mechanisms of bacteria oxidation of sulfides were studied using Thiobacillus ferrooxidans and pyrite. The aim was to determine which of the two generally aeeepted mechanisms played a dominant role, if any, during acid mine drainage (AMD) formation from the oxidation of sulfide minerals. The results show that at a pH of 4.5 where T. ferrooxidans are quite active, but where initial chemical oxidation of pyrite to Fe2+ is limited, the bacteria were unable to directly oxidize pyrite to any significant extent. Whereas, in the presence of Fe2+, T. ferrooxidallS assisted oxidation of pyrite by the indirect mechanism was observed and sustained over the pH and Eb range where the bacteria is active. The results lead to the conclusion that the direct contactmechanism of pyrite oxidition by T. ferrooxidans is insignificant. The predominant, and possibly the only, pathway involves the indirect bacteria oxidation of available Fe2+ to Fe3+, which in turn oxidizes FeS2 to generate additional Fe2+ and acidity in a cyclic process.

Jan 1, 1996

By Junji Shibata

It is important to recover and reuse the metal values contained in various industrial wastes in a viewpoint of environmental preservation. Most of industrial products are made through the processes to separate impurities in raw materials, solid and liquid wastes being necessarily discharged as industrial wastes. Chemical methods such as solvent extraction, ion exchange and membrane, and physical methods such as heavy media separation, magnetic separation and electrostatic separation are considered as the methods for separation and recovery of the metal values from the wastes. In this paper, some examples of the application of solvent extraction to the treatment of wastes are introduced. The treatment of solid wastes such as Ni-Co alloy scrap, Sm-Co alloy scrap, fly ash and flue dust, and liquid wastes such as plating solution, the rinse water, etching solution and pickling solution are accomplished using solvent extraction technique.

Jan 1, 1996

By Jim Lauder, Russ Calow, Ken Maley, Michael Ounpuu, Stuart T. Caverly

"Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Concession Street, Lakefield, Ontario KOL 2HOAbstractOn-stream X-ray analyzers have become an integral part of modem milling operations. The calibration of these instruments is not difficult but must be performed carefully and with consideration for the principles of X-ray spectrometry. A discussion of successful calibration procedures as well as examples of several common mistakes is presented.IntroductionOn-stream X-ray analyzers (OSA) have become an integral part of modem mineral dressing plants. Advances in instrumentation and computer software make the analysis of process streams fast, accurate and precise. Proper instrument calibration that respects the fundamentals of X-ray spectrometry is essential if the data generated are to be reliable. Often the importance of this task is underestimated and delegated to a person with inadequate XRF training. Successful OSA calibration is the result of careful, systematic procedures.On-stream analysis is perhaps the most important tool that has been provided for the concentrator metallurgist. Combined with powerful, low cost PC's and distributed control systems, real-time elemental analysis affords today's metallurgist many opportunities to troubleshoot and optimize his process.Before OSA, operators had to be very experienced if they were to achieve good results. Even with hourly grab samples, most changes in control approach would still be based on visual cues from the circuit and gut instinct. Real-time analyses have changed that completely.The last two decades have seen a persistent drive to reduce production costs. Operations utilizing OSA have been the most successful in this endeavor. Direct benefits from the application of OSA are fairly obvious. Operators are able to make incremental changes in operational parameters (e.g. reagent addition, pH, cell level), and immediately monitor the effects. Variations in the characteristics of the mill feed can be identified and addressed immediately. More progressive operations have linked analyses to control loops to adjust process setpoints ( e.g. reagent additions), and to change them automatically according to formulas based on previous experience."

Jan 1, 1996

By A. R. Katti

The stone columns are widely used in the improving the bearing capacity of weak soils mostly for supporting flexible foundation systems. The load carrying capacity of a stone column is complex in nature. The load capacity is derived from the lateral stresses acting on the stone column due to load transmitted from the flexible structure due to deformation to soil mass and which in turn transmits lateral pressure in s3 direction. The load capacity is also function of the f value of the stone column, cohesion of the surrounding soil, K0 and Gb2 of surround­ing soil including passive resistance developed to lateral deformation of the stone column. The assessment of axial and radial deformation is much more complex. Recently Katti et.al. have developed a method based on a granular heap approach and computed with equivalent fe. which combines the effect of s3a and equivalent volume concept to estimate radial and axial strains. In this paper an attempt is made to put forward guidelines for design of stone column accounting for both stability with respect to shear and also with respect to settlement. The estimate of settlement are based on the internal properties of stone column and surrounding soil. It is considered thus the settlements computed are more realistic.

Jan 1, 1996

By Perring CS, Hill RE, Barnes SJ, Vallance SA

The Maggie Hays nickel sulphide deposit is located at latitude 32¦ 15 &apos;S, longitude 120¦ 30&apos; E on the Lake Johnston (SI 51-1) 1:250 000 map sheet. The deposit occurs in the Lake Johnston greenstone belt, in the Southern Cross Province of the Archaean Yilgarn Block, 500 kilometres east of Perth, Western Australia (Figure 1). The remoteness of the Lake Johnston greenstone belt and its poor access, restricted previous exploration activities and the full appreciation of the geology and its Ni-sulphide potential. It was not until 1991, when Forrestania Gold NL commenced exploration activities, that the geology of the ultramafic units and their potential to host significant concentrations of Ni sulphides were clearly established. This paper, which describes the geology and the characteristics of the Maggie Hays deposit, is based on the results of exploration by Forrestania Gold NL and a collaborative research agreement between CSIRO Division of Exploration and Mining and Forrestania Gold as reported by Perring, Barnes and Hill (1994), Perring and Hill (1995), Perring (1995 a and b) and Barnes, Perring and Reilly (1995). A comprehensive description of the geology, petrology and geochemistry of the deposit is being prepared for publication by CSIRO (Pemng, Hill and Barnes, in press).

Jan 1, 1996

By Robert L. Hautala

In 1978, Congress established a series of mineral institutes for a limited time to assist financially in mineral industry education and research. Later, education and research were separated, establishing generic institutes for specialized research that transferred the former research budget from the base mineral institutes program. One of the generic institutes is the Mine Systems Design and Ground Control (MSDGC). It provides for research funding specifically for mining. Other parallel generic institutes were established in pyrometallurgy, comminution, waste management, etc. MSDGC was established at Virginia Polytechnic Institute and State University(VPI). The founding group included the University of Alabama, University of Kentucky, University of Nevada Reno, University of Idaho and University of Alaska reporting through VPI to the US Bureau of Mines (USBM) and Congress. Other universities also participated on an ad hoc basis.

Jan 1, 1996

By Richard Cole

The Energy Act of 1992 has many users of ac-induction motors eyeing premium-efficiency motors with mixed feelings and perhaps some confusion. When the October 1997deadline arrives for compliance with the1992 standards, the winners will be the environment due to reduced need for more power generating plants and the petroleum economy because of reduced dependency on foreign oil. But what will it mean for industrial users? The most obvious benefit is the potential for smaller electricity bills. Motors account for about 64% of the electricity consumed in the United States, at a yearly cost of $112 billion. Every 1% reduction in motor demand cuts 0.64%, or $716 million, off the industry wide bill. Higher efficiency motors also run cooler. This lightens the load on air-conditioning systems and further reduces plant demand. Lower total demand can lead to lower rates by helping to minimize peak-demand surcharges. As rates increase over time, these savings get bigger.

Jan 1, 1996

By William R. Yernberg

Caterpillar introduced 21 new products during Caterpillar Press Days ‘96, held in June at the company’s proving grounds near Tucson, AZ. The event, billed as the largest product introduction ever held by Caterpillar, was attended by press from around the world. Most of the new products were demonstrated at Caterpillar’s Tinaja Hills Training Center in the Sierrita Mountains south of Tucson. Under the scorching Sonora Desert sun, the press was treated to demonstrations of the new equipment. After a display of the equipment’s power and capabilities, the press was given an opportunity to operate the new models and, in some cases, compare them with the old.

Jan 1, 1996

By Turgut Yalcin

"In this study, potential benefits of focculant usage were explored in the processing of mill tailings by hydrocyclones. Tests conducted on copper-nickel mill tailings have demonstrated that, under suitable conditions, flocculation could significantly enhance solid-liquid separation in hydrocyclones. For example, at a feed pulp density of approximately 9%, focculant-assisted hydrocyclone produced an underflow with over 98% solids recovery, compared to a recovery of less than 53% with conventional hydrocyclone. However, feed pulp density was found to be a critical factor, and tailings with pulp densities of greater than about 15%required a two-stage hydrocyclone operation where the focculant-assisted hydrocyclone was employed at the second stage to process the overfow of a conventional hydrocyclone.The underflow and overflow products obtained from the focculant-assisted hydrocy-clone may be discharged into tailings dams in the same manner as those produced by gravity thickeners. The focculant-assisted hydrocy-clone would, however, provide a higher throughput."

Jan 1, 1996

By Ronald J. Riberich

The Mineral Economics and Management Society (MEMS) held its fifth annual conference in Montreal, Quebec, Canada earlier this year. “The Minerals Industry: Responding to the Global Challenge” was the first MEMS conference to be held outside of the United States. About 125 mining- and minerals-related professionals attended. The MEMS program included six sessions and three distinguished speaker addresses. The session topics included: “Minerals in the Macro economy: Development in Demand,” “Trends in Global Metals Supply: The Producers’ Challenge,” “Global Environmental Issues: Policy Perspectives,” “Global Environmental Issues: Quantitative Analysis” and “Minerals in the CIS: Phoenix or Albatross?” A student session was also offered. It provided a competition for monetary awards for outstanding papers.

Jan 1, 1996

By J. W. Rogers, S. K. Schwartz

"The Cape Breton Development Corporation (CBDC) is a federal Crown corporation which operates two coal mines (Phalen and Prince Collieries), a coal preparation plant, a railway, a central workshop and a deep water shipping facility.The Sydney coal field consists of 11 major seams, which range from 0.8 m to over 3.7 m in thickness. Of the 2.4 billion tonnes of known coal resources in the field, approximately 550 million tonnes can be mined with present mining technology. These parameters define reserves which extend more than 8 km beneath the ocean to a depth of 1200 m. With today’s design and present high production faces, the colliery life is projected at approximately 20 years."

Jan 1, 1996

By Ray Brandon

The recent introduction of polymer geogrids for ground control purposes in underground mines allows mine operators more flexibility in choosing improved products for several applications. This is evidenced most clearly in longwall recovery operations. Since November, 1994, many mine operators have chosen Fortrac geogrid assemblies for the purpose of securing longwall recovery areas prior to shield removal. Fortrac is a lightweight, strong, and flexible polyester geogrid available in many strengths. Utilizing the "diamond" seaming method, different strengths of Fortrac geogrids are easily fastened together so stronger geogrids may be placed in the most critical areas and lighter geogrids in less critical areas.

Jan 1, 1996

By Jillian Spindura

This work investigates the carbothermic reduction of the complex sulphide mineral, pentlandite, in the presence of lime. The effects of change in temperature and the use of different carbon sources are studied and the role of these variables on the reducibility of pentlandite mineral is discussed. The microstructures of the heat-treated pellets are examined using X-ray diffraction and scanning electron microscopic techniques. The latter analytical method also allows any variation in the morphology and composition of the metallic phases formed, with temperature, to be considered. The kinetics of the reduction process is studied and the magnitude of the overall activation energy is determined from the plots of percentage reduction versus time.

Jan 1, 1996

By G. M. Molinda

Ground Penetrating Radar (GPR) is being investigated for the potential to determine roof hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth in order to determine the value of GPR for roof hazard detection. The resolution of the current system allows detection of gross roof fractures (>63 cm (s1/4 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologic changes in the roof. Differences in data quality are discussed, as well as suggestions for collecting improved data.

Jan 1, 1996

By R. J. Sweigard

One possible alternative for disposal of flue gas desulfurization (FGD) by-products is use as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation of stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix proportioning of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48 percent and the peak stress could be decreased about 58 percent. The study indicates that fairly weak FGD materials can eventually lead to stability of backfilled highwall adits.

Jan 1, 1996

High pressure grinding mills have been successfully introduced in the industry. They offer the possibilities for capacity increase of existing plants and reduction of operating costs. Further metallurgical advantages in gold and copper are possible. The plants in operation are running in different applications and modes of operation. They can be installed in a combination with SAG and ball mills or in a stand-alone mode. In combination with other grinding mills, it has to be investigated how the HPGR can be installed to reach the full efficiency. This paper describes the possibilities to implement high pressure grinding rolls and shows by case studies the potential of savings which could be reached

Jan 1, 1996