Search Documents

By A. R. Laplante

A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; an error analysis is detailed; possible uses are discussed. Of the 38 samples tested, the lowest GRG content was found to be 25% (most below 25 11m, or 600 mesh), and the highest 94% (most above 300 11m, or 50 mesh). The average GRG content was 63%, with a standard deviation of 19%. Error analysis shows the test to be reproducible within 5 to 10%, depending on the size distribution and grade of GRG, and the sample extraction protocol. When using the same primary sample, reproducibility improves, 2 to 5%, depending on the amount of gold coarser than 850 11m (20 mesh) and sample weight. The test has been applied to greenfield project and retrofit applications, to determine the suitability of gravity recovery. For existing circuits, it has been coupled with a model of gravity recovery for optimization studies.

Jan 1, 1996

By A. Mukherjee, C. Kelly, B. Markovich, G. E. Agar, G. E. Robertson, F. Khan, B. Shea

"Laboratory batch flotation tests were performed on a sample of bulk slow cooled converter matte (Cu:Ni = I) to optimize the time in each of the separation stages. Numerical simulations were carried out to estimate a continuous circuit material balance for the conditions selected. An experimental simulation of a continuous circuit (locked cycle test) readily came to steady state and there was reasonable agreement between the numerical and experimental results. The use of nitrogen as the flotation gas and the addition of collector to the grinding mill minimized the oxidation of chalcocite, which has previously resulted in increasing circulating loads, and led to a stable circuit with very low weights in the recycle streams.IntroductionINCO Limited developed a flotation process for separating the components of copper-nickel matte [Sproule, Harcourt and Rose 1945; Sproule, Harcourt and Renzoni 1960] in 1945 to replace the Orford process and continues to use the flotation process in almost the original mode to this day. Initially the matte processed was the result of smelting a nickel concentrate that analyzed about 12% nickel and 2% copper and all of the recycle material that was generated in the smelting process. The matte generated analyzed about 25% copper and 53% nickel, roughly 2: 1 nickel to copper. This matte was blown in Pierce-Smith converters to be sulfur deficient in order to produce a metallic phase that collected the precious metals contained in the smelter feed [Wilson and Stratton-Crawley 1991]. This process continued with little change until 1994 when the separation of chalcopyrite from pentlandite in the Copper Cliff mill was discontinued after 63 years of operation. As a consequence of the elimination of the primary separation of chalcopyrite from pentlandite in the milling process a bulk concentrate was produced for smelting. Bulk concentrate smelting came into practice in 1994 as part of the initiative to meet government legislation that restricted the emission of sulfur dioxide to the atmosphere. Previously, the copper concentrate was smelted in an INCO oxygen flash furnace which resulted in the capture of a high strength sulfur dioxide stream from which liquid sulfur dioxide was produced. Nickel concentrate was smelted in reverberatory furnaces that produced low strength sulfur dioxide gases which were difficult to treat. The action taken by INCO to meet the environmental constraints was to smelt a bulk concentrate in oxygen flash furnaces which would produce gases suitable for the production of liquid sulfur dioxide and another stream that was high enough in sulfur dioxide to be readily converted to sulfuric acid [Bell et al 1990]. The end result of this decision was that all the copper-nickel separation would be done in the matte separation plant."

Jan 1, 1996

By F. J. J. van Loo, A. A. Kodentsov, J. A. van Beek, M. R. Rijnders

"A periodic layered morphology of the reaction zone has been observed in several annealed solid/solid diffusion couples, including metal/metal and metal/ceramic couples. This morphology is characterized by a regular array of alternating layers, which are either single-phase layers or bands of particles embedded in an intermetallic matrix phase. A description of several systems showing periodic layer formation is given. It is shown that the periodic layered structure with the single phase layers and the one with the bands of particles have a different mechanism of formation.IntroductionSolid state reactions in ternary systems can produce a variety of reaction zone morphologies if there are two or more reaction products. Three types of morphology have been described in detail: 1) simple layered; 2) isolated precipitates in a singlephase layer; 3) interpenetrating columnar (lamellar) or interwoven structure. Understanding the factors that govern the formation of different morphologies is of importance in many fields of engineering. For solid state displacement reactions the conditions governing the formation of these morphologies are well understood [1-4]. For example, the development of a layered or aggregate reaction zone depends on the relative diffusivities of the components through the reaction products.This paper is concerned with the periodic layered morphology which has been observed in various solid state systems. We consider this to be a fourth type of reaction layer morphology. Two manifestations of periodic layered morphology may be distinguished. One form consists of regularly spaced layers of particles of one reaction product embedded in a matrix phase (another reaction product). The other form consists of single-phase layers embedded in a matrix phase. It will be shown that each manifestation has its own mechanism of formation. In section A we consider a system (Ag/Ti-foil/Si) in which periodic layer formation will be explained as a special case of the Liesegang phenomenon. In section B we consider systems where the periodic layered structure has a different origin."

Jan 1, 1996

With the change in legislation under the Resource Management Act 1991 (RMA), the responsibility for administering the effects of blasting on the environment, has transferred from an essentially central government system to local bodies. This naturally will allow for a variety of compliance levels and control procedures which will depend on the particular local body and rather ad hoc arrangements. It is anticipated that the existing NZ Standard on blast vibration levels will soon be replaced by the Australian Standard. These changes raise the question as to what should be used as suitable compliance levels to prevent damage to structures. The paper will address the measurement, control levels and the appropriateness of current standards in relation to the overall legal framework of the RMA.

Jan 1, 1996

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

By Xu Tianrui, Jin Xiang, Pen Dianhua

Based on the results of research or investigation, this paper describes the causes of and countermeasures for unexpected accidents, such as premature, postponed or spontaneous explosions in blasting practices in China.

Jan 1, 1996

By J. van der Walt

The Meikle Mine is located in the northeastern part of Nevada in the gold-rich Carlin Trend. First discovered in 1989, Meikle is being developed into a 2.2-kt/d (2,500-stpd) underground mine that will open during the second half of 1996. Work has already been completed on the mine’s cooling plant, a necessary item due to the high rock temperature and the hot ground water. In North American mines, there has been little need for refrigerated cooling. Therefore, Barrick needed to draw on experience from elsewhere in the world — particularly South Africa — to meet these requirements. The history of cooling mines using mechanical refrigeration dates back to the 1920s at Morro Velho in Brazil and 1936 at Ooregum in India (Dobson,1940 and Biccard, 1946). From 1940 to 1960, several cooling plants were installed on the deep level gold mines on the Witwatersrand in South Africa. These were followed by similar installations on the mines in the Klerksdorp, Welkom, Evander, Rustenburg and Thabazimbi areas. The first mine cooling plant in Germany was built during 1976.

Jan 1, 1996

By I. V. Baklashov

Geomechanical conditions of mining operation are determined by varying in time and space mechanical properties and initial state of the rock mass, by geological and technological factors. We define adaptive mining technology as a technology capable of adjusting to changing geomechanical conditions of mining operation. The ongoing research at Moscow State Mining University consisting of laboratory, theoretical, and field investigations aims at the development of theoretical basis and methodology of the system of geomechanical support of adaptive mining technology for the bedded salt deposit in the Urals, mined by room-and-pillar method. This system of geomechanical support is capable of - dynamically assessing mechanical properties and state of the rock mass varying within the panel; - mapping mechanical properties of the rock mass within the panel; - assessing and predicting mechanical condition of load-bearing elements of the rock mass and its changes due to the adjustment of the parameters of mining operation considering the in-situ geomechanical conditions.

Jan 1, 1996

By Satu Jyrkönen

A single-particle laminar-flow technique was used to study oxidation of four synthetic nickel mattes, which were screened into three size fractions, Experimental conditions were: reaction gas from N2 - 21 to 75 vol-% O2; gas preheating temperatures ranging from 500 to I 100'C. The four mattes were synthesized so that Ni/Cu ratios of I and 10 were obtained with high and low iron contents. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect their morphology, internal composition and structure. The best sulfur removal from the synthetic nickel mattes was achieved under the most oxidizing conditions with the finest size fraction. The matte with Ni/Cu = 1 and high iron content was found to be most reactive. The least reactive matte was with Ni/Cu = 10 and low iron content; the coarse fraction particles did not react at all under the conditions studied.

Jan 1, 1996

By Yi Luo

In the study of the topographical effects on surface movement due to underground longwall mining, the factors that affect the incremental horizontal displacements are identified using 10 collected cases. Based on this study, the angle of surface natural slope is the major contributor to the incremental horizontal displacement while the total movement is also playing an important role in some cases.

Jan 1, 1996

By H. Cho

A study was undertaken to investigate the liberation behavior of coal macerals through size reduction and density separation. It was seen that the liberation of coal organic components could be achieved by size reduction, allowing selective separation of coal organic components. However, the degree of liberation is dependent on the history of coal: the extent of liberation decreased when the size of the primogeniture coal decreased. The liberation of coal macerals was analyzed by examining the Liberation Index. It was seen that although comminution produced fine particles enriched in inertinite (primarily fusinite and semifusinitie), these particles were less liberated than the coarser particles. However, the liberation of macerals increased when all the feed was ground to a finer size.

Jan 1, 1996

By Thomas P. Battle

Ilmenite (iron titanate) is the source of over 90% of all the titanium produced in the world today. At some point during production of titanium dioxide or titanium metal the iron impurity must be removed. Too often it becomes a waste instead of a product. DuPont and MINPRO have developed a solid-state process which separates the iron and titanium components of ilmenite into different high-purity powders, which can be separated using conventional mineral processing techniques. The main reactor in this process is a unique high-temperature ball mill, where the iron segregates from the ilmenite lattice with the assistance of catalytic quantities of He\. The results of lab, pilot plant, theoretical, and scale-up studies are presented and discussed.

Jan 1, 1996

By J. H. Kelley

In this paper, we show that the methane emission and the dust generation in under-ground mining currently and in the future pose operational, health and safety conditions which adversely Impact face productivity and worker satisfaction. One solution is the use of a dual-aircourse system of ventilation. In this concept, one aircourse captures and exhausts to the surface the dust generated and the methane emitted in coal/mineral fragmentation while a second aircourse provides workers with cleaner air for breathing and comfort. Various dual-aircourse configurations adapted to the Variable Wall Miner are analyzed and compared with conventional mining in gassy seams, indicating a marked reduction in the required air quantity and the number of aircourses.

Jan 1, 1996

By Versiane A. Leão

The adsorption of oleic acid and amine, by Expanded Hydrophobized Vermiculite (EHV) was studied. In appropriate conditions EHV is a good adsorbent for these flotation re-agents and the best results are obtained at situations where the chemicals are at non-dissociated form. The adsorbent shows good chemical stability and may been used in many adsorption-desorption cycles.

Jan 1, 1996

By H Bibby

Initial analysis of Long Offset Time Domain Electromagnetic (LOTEM) data has traditionally been made in terms of early and late time apparent resistivities. By using more than one grounded bipole as a source, a tensor analysis technique analogous to the method used to analyse DC resistivity multiple-source bipole-dipole surveying may be formulated. We define the æinstantaneous apparent resistivity tensorÆ as the tensor that relates the total electric field vectors at each instant to the steady state (DC) uniform half space current density vectors due to each source. Instantaneous apparent resistivity tensors calculated for a 3D resistivity model suggest that profiles of LOTEM measurements across simple 3D structures can be used to create an image that reproduces the main features of the subsurface resistivity. Where measurements are distributed over an area, maps of the tensor invariants or the tensor ellipses at different times can be made into a sequence of images which provide a way of ætime slicingÆ down through the target structure.

Jan 1, 1996

By F. H. A. Abdalla

A process is described for the recovery of valuable nonferrous metals from steelmaking dust by suiphatizing roasting using ammonium sulphate. Maximum recoveries of soluble metal sulphates achieved at optimum conditions were> 99.0 %. Selective metal separation of the soluble sulphates in the leached liquors were performed either by controlling the roasting temperature or by adjustment the pH values of the leached liquor ranging from 3.6-6.2. Either pure zinc oxide orland tin oxide could be obtained at optimum conditions, and the products were evaluated chemically and by X-ray analyses. The residues rich in iron oxide can be removed and recycled. The mechanism of sulphatizing roasting process was considered. A general flow-sheet for the overall process of treatment the steel making dust to recover its valuable nonferrous metals was suggested, which ca be applied for other nonferrous bearing materials.

Jan 1, 1996

By John R. Holliday, William Marcum

Apogee Coal Company, DBA Arch of West Virginia, faced the challenge of drilling and blasting over one million cubic yards of high temperature overburden at its Ruffner surface operation near Logan, West Virginia. The overburden was removed above the Upper Five Block seam that was previously deep mined, abandoned, and later engulfed by fire. Borehole temperatures were measured above 700” F.

Jan 1, 1996

By Rolando V. Cuaño

For geostatistical applications, heterogeneous spatial phenomena are better modeled as mixtures of populations. However, the modeling of the constituent populations can become complex. The alternative mixture model offers a simplified approach to the w modeling problem. The model is applied and tested on the Walker Lake data set. Compared to the univariate ordinary kriging model, the alternative model generates less biased block estimates.

Jan 1, 1996

By A. B. Desai

The construction of 1144 nos. of piles, each 1.5 m diameter, bored-cast-in-situ type and varying in depths from 6.5 to 23m, has been completed as foundation for 26 piers of 548 m long aqueduct across Orsang river to carry 1128 m3 water of Narmada Main Canal of the Sardar Sarovar Project in Gujarat. These piles are socketed 1.5 m into foundation grade rockmass. The portal system of 44 nos. of piles and pile cap at the top for each pier is analyzed considering the portal fixed at bottom of piles. The borings for pile shaft were done deploying reverse mud circulation rigs and also by conventional chiseling and bailing operations. Besides vertical loading tests and lateral loading test on piles, dynamic tests such as low strain integrity testing on 290 piles and high strain pile testing on 17 piles were also conducted. The results indicated that (a) the settlement/ displacement are much less than the prescribed limits (b) good quality of concrete (c) piles are firmly socketed and (d) piles have adequate structural capacity to withstand the design load.

Jan 1, 1996

Slide presentation at conference

Jan 1, 1996