Search Documents

By Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa

"Thermodynamic properties of impurities in molten silicon are of prime importance in developing economical production methods of solar grade silicon. In the present research work, thermodynamic properties of boron, the most difficult element to remove from molten silicon, were measured by chemical equilibration techniques at 1723 and 1773 K. Activity coefficients and self-interaction parameters of boron in molten silicon were determined by equilibrating the melt with solid BN under controlled nitrogen partial pressures. Interaction parameters between boron and nitrogen in molten silicon were also determined by equilibrating the molten Si-B alloys with solid Si3N4• Based on the data obtained, the stability diagram of the Si-B-N system was established.IntroductionPhotovoltaic power generation using a silicon solar cell is expected to be the most promising energy source, because it is inexhaustible, cleaner and more safety than conventional energy sources, such as thermal or atomic power generation. At present, expensive off-grade silicon for semiconductor (SEG-Si) is used for a solar cell production. However, if a large-scale photovoltaic energy conversion using silicon solar cell comes into wide use in the near future, silicon will be sure to be in short supply for the cell. Therefore, a development of a new large scale process for solar grade silicon (SOG-Si) production is definitely necessary, which can remove contained impurities from silicon.Among the impurities contained in silicon, boron is one of the most difficult ones to remove by a zone melting or an unidirectional solidification, because its segregation coefficient in silicon is close to unity (0.8). In addition, boron behaves as a p-type silicon semiconductor dopant and, therefore, its content in SOG-Si must be severely controlled. Although some attempts to remove boron by various metallurgical methods have been carried out [I -4], quantitative analysis has not been made due to lack in the information on the thermodynamic properties of boron in molten silicon. From this view point, the activity of boron in molten silicon was determined in the present study by chemical equilibration techniques at 1723 and 1773 K."

Jan 1, 1998

By F. T. Principe

In order for solvent extraction technology to be acceptable as an alternative to existing jarosite precipitation circuits, iron must be cleanly separated and concentrated into a feed stream suitable for downstream iron by-product recovery which meets market specifications and economics. Ten years ago, significant progress was made in a joint McCill University/CANMET project that involved iron extraction with mono(2-ethylhexyl) phosphoric acid and stripping with HCI. Our iron solvent extraction research was reactivated recently by looking into this and other members of the organophosphorus extractant family. Our research focuses on the mechanisms and control of anion (SO42/CI) transport across the various phases (Rafinate/Organic/Strip), iron build-up in the strip liquor, and extractant stability/selectivity. In this paper, these issues along with some other performance parameters are discussed using data derived from an extensive search of the two commercially available and best known members of the organophosphorus family, di-2-ethylhexyl (D2EHPA) and mono-2-ethylhexyl (M2EHPA) phosphoric acid. Further in this discussion, the challenges lying ahead in the development of sx systems that overcome the deficiencies of D2EHPA and M2EHPA are outlined. In particular, the necessity of considering secondary separation technologies that can further concentrate iron values in the chloride strip liquor to levels economically attractive for the production of saleable iron oxide by pyrohydrolysis is addressed.

Jan 1, 1998

The estimation of the shear stress distribution around an excavation is important to the design of the excavation since shear stresses can generate cracks, loosen grain boundaries or otherwise degrade the mechanical and physical properties of the rock and lead to stability problems. In this study, the distribution of shear stresses in a pillar were back-calculated from the deformation measurements made from the SPDV (Site and Preliminary Design Validation) area at the Waste Isolation Pilot Plant (WIPP) site. A plausible pattern of shear stress around an excavation has been suggested based on the Zero Strain Boundary (ZSB) calculation, computer simulation using FLAC, and back-calculation using measured deformation rates in the pillars.

Jan 1, 1998

By Courtney A. Young

Cyanide is a fast-acting, highly toxic substance but, at the same time, is deemed essential for sustaining life as well 'as our standard of living. In this manuscript, the facts about cyanide are presented beginning with a brief history and definition and ending with a discussion on cyanide alternatives. Other topics include speciation, physical characteristics, toxicity, manufacturing, cyanogenics, cyanide cycle, separation, destruction, and markets including those outside the mining industry. Emphasis, of course, is placed on gold production by leaching and how it is influenced by ore type, mineral characteristics and economics as well as its advantages and disadvantages.

Jan 1, 1998

By G. L. Liu

"Deformation Banding ( DB ) in cold rolled mild steel has been experimentally established by microstructure investigation. Deformation banding model includes such deformation mode when it is applied to rolling texture simulation. The cause for the occurrence of deformation banding is the reduction of the total work for plastic deformation through a relaxation of the deformation constraints. In the first DB model, all grains are assumed to band from the first deformation step. Such an unrealistic assumption has been eliminated in the new model by the introduction of a banding criterion based on an energy minimizing approach. The prediction is closer to the measured texture by applying banding criterion and setting critical resolved shear stresses (CRSS) ratio for { 110 } and { 112 } slip modes to 0.85.IntroductionBased on the continuum theory of plastic flow and deformation mechanism of crystallographic dislocation slip, Taylor's FC ( Full Constrain ) theory [1] has been widely used in texture modeling. As the process of cold rolling of sheet materials produces a microstructure consisting of elongated or equiaxed flat grain or cell, the ""lath"" and ""pancake"" relaxed constraints ( RC ) models [2, 3] were introduced as the successful improvements over the classical FC model. It has been also recognized that crystals may split into different orientations during deformation and the term deformation banding is used to describe such deformation processes [4, 5]. Lee et al. [6, 7] pointed out that the success of the RC theory in predicting textures depends on the physical processes of deformation banding. They developed so called Deformation Banding ( DB ) model by considering DB in the longitudinal plane to be accounted for by the RC method and allowing DB in the rolling plane. DB model was applied to simulate the texture development in bee case [8], the predicted bee rolling textures are in reasonable agreement with the measured textures. In the first DB model, however, all grains are assumed to band right upon the first deformation step. A banding criterion was formulated [7] which states that DB will occur if the work used in DB model is less than that in RC model. Such criterion has been incorporated into the original DB model for texture simulation and is referred to as DBC ( Deformation Banding Criterion ) model."

Jan 1, 1998

By Ron Bromenschenkel

The State of California, Department of Transportation is currently retrofitting a major interchange near the San Francisco area. The project is located in a highly traveled area of Oakland with light rail commuter service near many footings. Over 600 micropiles are being used in conjunction with CIDH piles for footing stabilization. A specially designed Soil Nail pile will support footings for a new light rail utility structure. Pile testing features in this contract serve as points of interest for future foundation designs. The presentation focuses on substructure issues of this incterchange retrofit. Both design and construction considerations will be covered. Design Considerations: ? Project Description ? Structure inadequacies ? Design criteria ? Design contraints ? Retrofit strategy ? Consultant analysis ? Pile Designs and Test Sites ? Contract Specifications ? Construction Plan and Cost

Jan 1, 1998

By G. T. Adel, P. E. Richardson, R. Pazhianur

Cathodic protection using impressed current was employed to reduce mill wall wear during ball milling. Wear rates were determined from weight-loss measurements made on four 1-in.-diam mild steel coupons that were installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH levels of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 30% to 60%. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It was also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1998

By M Grossi, G Baiden

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and onsite applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no dewatering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By William J. Miles

The inhalation of dust has been a problem in the mining industry since antiquity. Crystalline silica is now known to be the cause of silicosis, a form of pneumoconiosis that is associated with excessive exposure to respirable particles in some mining and industrial environments. Crystalline silica was reviewed by the International Agency for Research on Cancer (IARC) in 1986 and classified as a Group 2A, Probably Carcinogenic to Humans in Volume 42 and Supplement 7 of the IARC Monographs (1987). In 1996, IARC reviewed additional literature and studies published in the intervening decade and recommended that quartz and cristobalite, two polymorphs of crystalline silica, be listed as Group 1, Carcinogenic to Humans. Their recommendations and reclassification were published in 1997 in IARC Monographs 68.[2] In both Monographs, IARC classified amorphous silicas as Group 3, Inadequate Evidence for Carcinogenicity to Humans.

Jan 1, 1998

By K. J. Shoop

Coal-fired power plants in the U. S. produce approximately 20 million metric tons of Hue-gas desulfurization sludge every year. The sludge mainly consists of calcium sulfite and calcium sulfate. This can be converted to synthetic gypsum, which in principle could be a marketable commodity. However, many Hue-gas scrubbers produce sludges that do not meet the quality requirements of the gypsum industry, and so their sludges must be landfilled as a waste. If a suitable method can be developed for removing certain objectionable impurities from the sludge, it will then be possible to market the material instead of landfilling it. A sludge from a natural-oxidation scrubber was characterized, and the main contaminant was found to be calcium carbonate from unreacted limestone. Based on the particle size and the characteristics of the material, froth flotation was considered as a method for purifying the material. Since no flotation studies have ever been carried out to separate calcium carbonate particles from calcium sulfite or calcium sulfate particles, it was first necessary to select a suitable collecting reagent. Based on Zeta-potential studies, the most suitable reagent was found to be an octadecylamine-octadecylguanidine complex. Results are presented for flotation of calcium carbonate from scrubber sludge using this reagent, in a reverse-flotation process. The best results were obtained when the sludge was first pre-cleaned using a water-only cyclone to remove unfloatable coarse limestone, followed by froth flotation to remove fine limestone.

Jan 1, 1998

By K L. Brown, J L. Mauk

Sulfide-rich scale occurs in steam and water lines at the Ohaaki geothennal field,Taupo Volcanic Zone, New Zealand. Precious metals show very high concentrations around areas ofpressure reduction (Au 15500 ppm, Ag 68800 ppm). Pyrrhotite dominates at the orifice plate due to low PH2s1PH2 conditions. Sulfide mineralogy in the scales is consistent with alteration mineralogy of the reservoir rocks. Separated steam then produces a mainly pyrite/magnetite mineralogy, with lesser chalcopyrite, where textures reflect high flow rates and high levels of supersaturation. This study outlines the effect that pressure and subsequent temperature decreases have on the mineralogy, chemistry and textures of sulfide scales.

Jan 1, 1998

By Robert Martin, Brian W. Stump, David P. Anderson

2We use field measurements to quantify physical processes that accompany different types of mining explosions. The data sets collected include three-component ground motion, acoustic, video and high speed film, three dimensional topography, geological and geophysical properties, design blast pattern and timing, and velocity of detonation in the explosive for individual borehole detonation times. The explosions include simple single-fired contained explosions, ones designed to bulk and fracture material and those that cast material. Our goal is a physical understanding of these sources for the purposes of optimizing blasting practices.

Jan 1, 1998

By J. T. YIi-Penttiia

Dust formation and reaction mechanisms of copper matte particles were investigated in simulated flash oxidation conditions. The granulated and ground matte consisted of 72 wt% Cu, 4 wt% Fe and 21 wt% S. Experiments were conducted by using a laminar-flow furnace with a reaction gas composition ranging from 20 vol% to 75 vol% O2 in nitrogen. The particle feeding was carried out by the single-particle method and samples were quenched after a specified reaction time (approximately 0.05-004 s) in a cold water film. Experimental temperatures were between 800 and 1300°C. Chemical analysis was used to determine oxidation degree, and an optical and scanning electron microscope combined with energy dispersive analysis was used for characterization of the reacted particles.

Jan 1, 1998

By Laros T, Schoenbrunn F

Deep paste thickeners have been proven capable of consistently producing medium to low slump material for disposal without the need for filters. However, proper design of the entire system is critical for a paste project to he successful. Some of the factors that must be carefully considered in design of a paste system include thickener sizing, tailings inipoundineni design, underflow pumping, and control system.

Jan 1, 1998

By B. K. Slone

The depth at which it becomes more economical to use slope access as opposed to box-cut access for near-surface coal reserves, termed "transition depth," can be established for a given coal property by considering cost estimates for those parameters that determine respective access method. Fourteen parameters that influence access cost were identified and ranges determined. A Transition Depth Formula was developed to permit determination of the better method of accessing a reserve, given such information as highwall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs, and cost of overburden removal and reclamation. In most cases, in Appalachia, studies indicate that the transition depth ranges between 20 and 30 m.

Jan 1, 1998

By R. L. Zick

The High Density Sludge Process was originally developed by Bethlehem Steel Corporation for use on acid mine drainage and diluted waste pickle liquor discharges requiring continuous chemical treatment systems. This work began in the early 1970s and was first put into practical use around 1973. To date there are approximately 15 operating systems which have been installed on mine drainage in the United States, and another 10 systems worldwide. Dense Sludge is an innovative and improved method for treating acidic metal bearing streams in a manner which minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge recycle process which forms particles that have a low affinity for water, unlike conventional metal hydroxide solids which contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations which combine with calcium ions in lime based treatment systems to form gypsum crystals. The physical form of this gypsum is radically altered when the Dense Sludge process is utilized compared to the form generated in conventional lime treatment systems. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. Slides No. 1 and No.2 show scanning electron micrographs of conventional and densified sludges illustrating these differences. The magnification used was 300X. The dense sludge particles settle faster, dewater more readily, are more easily pumped, and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered.

Jan 1, 1998

Since it was first introduced, the Coal Mine Roof Rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground control problem. Extended cuts (cuts greater than 6 m (20 ft) in length) are commonly used with remote control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof fall accidents. When extended cuts are attempted in weak roof, the roof may collapse before it can be bolted, causing hazardous conditions. Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended cut experience were collected at 36 mines in 7 states. It was found that when the CMRR was greater than 55, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken. Between 38 and 55, extended cuts were feasible sometimes but not others. The data also shows that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

Jan 1, 1998

Jan 1, 1998

By Chappell B

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to he placed in a tailings darn. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electro- osmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By Chend J

Research conducted into backfill drainage at Mount Isa Mines since 1992 is described. Piping in draining backfilled scopes has been the primary cause of bulkhead failures and emphasis is placed on research into the piping mechanism. Laboratory and in situ tests aimed at understanding the piping mechanism have been conducted and the results are presented. A case history of piping in a draining bench scope fill mass is described and a technique for reducing the potential for bulkhead failures in hench stopes is presented. Hydraulic fill is produced by standard cycloning of tailings and the overflow (reject material) is sent to thickeners prior to placement in the tailings dams. Research into the partial introduction of thickener underflow into the backfill system and its influence on backfill drainage is also descrihed.

Jan 1, 1998