Search Documents

By J. Gao, H. O. Gekonde, S. V. Subramanian

"The functional role of inclusions at low cutting speeds is to promote ductile fracture in chip formation process, whereas the role of inclusions at high cutting speeds is to prevent tool crater wear by suppressing the tribological phenomenon of seizure at the tool-chip interface. Glassy oxide inclusions are engineered into the workpiece to form a viscous layer in-situ at the tool-chip interface at high cutting speeds. The viscous layer lubricates the tool-chip interface to prevent the seizure. In comparison with the large volume fraction of inclusions needed for promoting ductile fracture at low cutting speeds, the amount of inclusions required for lubricating the toolchip interface at high cutting speeds is very small and is in the range that is typical of clean steels. The chip fracture process at high cutting speeds is aided by strain rate hardening of the matrix, which facilitates chip disposal of relatively clean steel.Inclusion engineering for high speed machining involves the control of the rheology and composition of inclusions to meet target viscosity at the tool-chip interface. The application of thermodynamic models in controlled production of inclusions in steels designed for high speed machining is discussed."

Jan 1, 1998

MIM Holdings Limited (MIM) committed to a long-term future in copper in the Carpentaria Mineral Province in 1996 with the development of the Enterprise and Ernest Henry mines, and an upgrade of MIMsÆ copper smelter in Mount Isa, and copper refinery in Townsville. The upgrade of the copper smelter will enable the smelter to produce 250 000 tpa of copper with a single primary smelting unit, the copper Isasmelt furnace installed in 1992. The copper Isasmelt furnace currently smelts concentrate containing 145 000 tpa copper. To reduce the risk associated with the copper smelter upgrade, and shorten the ramp up time of the upgraded smelter, two high-rate trials were undertaken in 1997 to demonstrate that the copper Isasmelt furnace could, with an additional 525 tpd of tonnage oxygen, treat concentrates containing 250 000 tpa copper. During the trials the concentrate feed rate to the Isasmelt furnace was increased from its average rate of 100 tph of concentrate to 150 tph of concentrate. The increase in the capacity of the furnace was achieved by: supplementing the installed tonnage oxygen capacity of 595 tpd with an additional 300 tpd supply; reducing variability in the furnace feed rate from ¦25 per cent to less than ¦5 per cent; and reducing tramp air. The Isasmelt furnace smelted concentrate at a rate of 140 to 150 tph for four hours 25 minutes during Trial 1, and at a rate of 150 tph of concentrate for five hours and 30 minutes during Trial 2. The oxygen utilisation was 100 per cent during the trials with the process remaining under control. As a result of the development work for the trials the average treatment rate of the furnace under normal conditions increased by ten per cent.

Jan 1, 1998

By B. J. Madden

Over 206 million tons of hard coal were mined in South African collieries in 1996. Some 132.5 millions tons came from underground operations and approximately 120 million tons came from bord-and-pillar workings resulting in between 100 000 and 150 000pillars being formed. Coal pillar design remains a significant feature of South African mining. This paper reviews South African coal pillar design procedures in the light of 90 pillar collapses that have occurred since 1904. It shows that, while the current pillar strength formula is still valid within the original empirical range of Salamon1,cognisance must be taken of local conditions. Current South African coal pillar research is attempting to account for the variations in local conditions with the emphasis on the effect of discontinuities and pillar deterioration. It is suggested that a more holistic approach to pillar design be adopted to include a design methodology that examines the stability of the roof, pillar and floor of the underground workings. Using this approach, deviations from the empirical database used by Salamon and Munro will be incorporated into the design methodology resulting in more stable underground workings.

Jan 1, 1998

By Patrick Ph. D. Kennedy, Osvaldo A. Ph. D. Bascur

With the revolutionary progress in information and computer technologies, applying the latest information technologies in metallurgical complexes has become a serious challenge to both a major opportunity and a serious challenge to both management and technical teams. The emerging component and object technologies are changing the way everyone can beneficially use their computer and networks to add to their corporate bottom lines. Most mining and metallurgical plants use predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis and oil and lube analysis for critical equipment. Process control strategies are installed in several metallurgical sites. All process equipment and control strategies require maintenance from local personnel at the mine. Integrated use of existing and emerging technologies is making it possible to implement an overall process effectiveness control index. This index is based on key indices such as losses due to plant availability, performance efficiency and rate of quality. The availability of real time and process history to identify the most critical part of the processing system from mechanical integrity is highlighted. An emerging plant integration paradigm is described to simplify the implementation of business enterprise resources management and distributed plant management systems.

Jan 1, 1998

By Nobumasa Kemori

Six kinds of copper '90ncentrates. were treated individually in a ,pilot scale. Outokumpu flsah smelting furnace ~n order to study their ?flash smelting behavior with respect to oxygen efficiency and dust generation. The copper concentrates tested were selected from the more than twenty sources which are treated at the Sumitomo Toyo copper smelter, so as to provide a wide range of chemical composition in terms .of Cu, S,Fe, Pb + Zn + As, and Si~ content. Oxygen efficiency 'and dust generation rates obtained in 'the experiments ranged from 80% ,to 108% and 11% to 20%, respectively. Relationships between these results and experhnental conditions such as chemical and mineral composition of the copper concentrates, flux ratio, fuel consumption and so on are also discussed quantitatively in this paper.

Jan 1, 1998

By Richard J. Haslinger, C. Mark Rebagliati, James L. Oliver

Abstract - Exploration at the Specogna gold deposit has identified a geological resource of 65.0 Mt grading 1.63 g/t Au, which equates to 3 million ounces of contained gold. This resource is hosted in a low-sulfidation epithermal deposit of Miocene age that is localized along the northwesterlytrending Sandspit fault. The fault has juxtaposed Late Cretaceous mudstone of the Haida Formation to the west, with Late Tertiary coarse clastic sediments and lesser andesitic volcanic rocks of the Skonun Formation to the east. A plagioclase porphyritic dacite dike intrudes the Haida mudstone and Skonun sediments along the fault. Gold mineralization, in hydrothermal breccias, veins and stockworks developed mainly in Skonun sediments and dacite. These are formed in an 800 m long zone that roughly parallels the Sandspit fault. The gold zone is funnel-shaped in cross-section, approximately 300 m wide at surface, 220 m above sea level, and narrows to approximately 50 m, at sea level. The deposit lies within an elongate zone of moderate to intense hydrothermal alteration that, at surface, extends over a known area of approximately 2 km2. Its western extent is bounded by the Sandspit fault. There is an asymmetric alteration zonation, with a core of silicic-potassic (adularia) and smectite-illite clay alteration that is bounded to the east by argillic alteration. Similar zoning defined by the distribution of metals reflects the position of the main feeder conduit. Mineralization of altered wallrock is dominated by 1% to 4% auriferous pyrite and marcasite. Gold and silver occur as electrum; individual silver minerals have not been identified. Other sulfides are rare, and are identified only microscopically. The mineral suite is typical of low-sulfidation epithermal systems. Gold occurs in early, multi-phase, variably bladed and banded quartz veins and breccias, which are cut by barren, single phase, drusy quartz veins.

Jan 1, 1998

By Larry M. Southwick

Steel mill electric arc furnace dust is a RCRA listed hazardous waste and its treatment and/or disposal are regulated by a complex set of rules. These regulations were originally established to encourage recovery and recycling of valuable components. For EAF dust, the more valuable constituents include zinc, lead, cadmium and iron. In fact, current trends are in the opposite direction, as the regulations have complicated the ability to commercialize new treatment technologies and created substantial roadblocks and liabilities for processors. As a result, almost half of the EAF dust generated in 1997 will be landfilled. The problems are compounded by difficult processing requirements, less than sterling examples of technology development and mechanical and operating problems. This paper explores some options to simplify the processing requirements and thereby easing difficulties in commercializing new technologies and expediting the recycling of recovered metals. Dust processing usually includes a simple step followed by two complicated steps. The simple step is fuming of heavy metals away from iron and other residues. The complex steps are (1) separating and purifying the heavy metals and (2) upgrading the iron residue. The first complex step can be simplified by producing an intermediate product that is amenable to processing by zinc refiners. This route benefits from the currently underutilized (by dust processors) resource offered by refiners, who have experience in and existing processes for separation and purification of zinc-based heavy metals. Various processes and their associated product options are reviewed and compared. Future directions for dust processing developments are suggested.

Jan 1, 1998

By R D. Morri, D J. Alexander

The design and optimisation of mineral flotation circuits is currently performed using a combination of laboratory, pilot plant and full scale testing. Owing to the variable nature of flotation circuits and the complex nature of the flotation process, it is difficult to interpret the data collected from flotation testwork. JKSimFloat is a computer modelling package which is being developed to interpret flotation testwork data collected at the various stages of the mining cycle. The parameters derived from the program can be used to assess potential circuit configurations in both the design of new flotation circuits and in the refinement of existing operations. The aim of this paper is to outline the modelling methodology used in JKSimFloat and to outline how it can be used effectively to model data collected from either the laboratory, the pilot plant or the existing flotation circuit. The use of flotation model parameters in circuit evaluation will be demonstrated via the use of a case study based on data collected from ComincoÆs Red Dog lead flotation circuit.

Jan 1, 1998

By Michel Boisvert

Noranda Metallurgy is presently completing construction of the new Noranda Converter (NCV) at its Home Smelter in Rouyn-Noranda. This capital investment of CDN$56M is the continuation of the Emissions and SO2 Reduction Program that was initiated in the late 1980s with the acid plant for Reactor off-gas treatment. The Patented Noranda Converter was developed and pilot tested at the Home Smelter in the early 1990s. The project will replace the Peirce-Smith Converters and enable sulphur fixation to be 'increased from 70% to over 90% by 2002 with an accompanying reduction of dust emissions to the atmosphere. The construction site is an extension of the present Noranda Reactor area. A number of existing facilities including the acid plant and process air supply were used to minimize the capital cost of the project. This paper provides a brief history of the Noranda converting process, the Home Smelter Emissions and SO2 Reduction Program, ,project implementation and construction, a description of the different facilities, and preparation of human resources for start-up.

Jan 1, 1998

By Garth James

Bacterial consortia capable of degrading cyanide and metal-cyanide complexes were obtained from gold mine process waters using enrichment cultures. The cultures contained either cyanide, tetracyanonickelate, or ferrocyanide as a sole nitrogen source. Several bacteria were isolated from the consortia, but none of these organisms were capable of degrading cyanide or cyanide-metal complexes at rates equivalent to those of the intact consortia. The consortium from the cyanide enrichment was capable of completely degrading cyanide from an initial concentration of over 100 ppm in less than one day, when cultured using a fed-batch method. Tetracyanonickelate and ferrocyanide were degraded more slowly. Overall, these results demonstrate that bacteria capable of degrading cyanide and cyanide-metal complexes can be isolated from mine process solutions and are capable of significantly reducing cyanide concentrations under appropriate conditions.

Jan 1, 1998

By Denby B, Hollands R. Schofield D

Surface mines are in operation worldwide, the vast majority employ large haul trucks for the transfer of material both to the outside world and around the site. The sheer size of these trucks and the operating conditions means there is a high

Jan 1, 1998

By M. Paventi, M. J. Scoble, B. B. Mohanty

There is no straightforward and systematic method for adequately measuring blast damage in on-going mining operations. This paper considers various techniques available for the measurement of blast damage, making particular reference to recent underground hardrock mine studies. This paper concludes by indicating the importance of understanding and accounting for geology and emphasizes the need for a robust damage-audit procedure.

Jan 1, 1998

By J S. J van Deventer, D C. Shallcross

New developments are taking place in the recovery of gold from leached pulps that are based upon the adsorption of the metal cyanide species onto ion exchange resins. Despite the success of several resin-in-pulp pilot plant operations in the Western World and large-scale plants in the former Soviet Union, the process is yet to gain recognition as a viable alternative to the carbon-in-pulp process. An experimental research program has investigated the use of a variety of different types of resins for the recovery of gold, but to-date no resin studied has the desired properties of high selective loading capacity for gold cyanide and a simple inexpensive elution procedure. In addition very little is known concerning the physical strength of resins and their ability to resist shattering due to osmotic shock during cycles of adsorption and elution. The ability of ion exchange resins to enhance the leaching of refractory and re-adsorbing ores has not been investigated. This paper highlights the necessary factors that need to be addressed before commercialisation of ion exchange technology for gold extraction is feasible.

Jan 1, 1998

For effective backfilling, a system with the 13 features covered under the section: effective backfill systems, is required. Effective backfilling cannot be done with systems that are badly designed, outdated or overextended. But in cases where the requirements for effective backfilling are overlooked, the shortcomings of such systems may wrongly come to be regarded as limitations to the capabilities of backfilling per se. Mining is currently done to depths of 3500 m, and is to go deeper since the gold-bearing reef extends down to 4000 m and 5000 m below surface. Effective backfilling systems will be required at such depths, and with suitable design this can be achieved. Mining the narrow tabular orebody of a typical South African gold mine is described at the start of this paper, then cycloned backfilling is discussed in general, and its effectiveness (most of the fill placed in South Africa is cycloned backfill or ædeslimed tailingsÆ).

Jan 1, 1998

By Dennis C. Martin

Assessment of the potential for mining induced subsidence and determination of ultimate design requirements for a mining operation should be based on a number of assessment approaches. Although the rock mechanics engineer has a variety of limit equilibrium and numerical modeling tools available for assessment and prediction of subsidence effects, empirical approaches based on precedent experience provide a powerful tool for calibration/verification of analytical models and prediction of subsidence. Three separate analyses approaches have been applied to the assessment of potential subsidence for a proposed block caving mine in eastern Canada. The investigations have included an assessment of documented historical information from previous block cave mining at the site, deterministic analyses using limit equilibrium approaches to assess kinematically possible failure mechanisms, and three-dimensional numerical modeling techniques. Analyses results have been used and compared with precedent experience and documentation of subsidence behavior from previous mining to optimize the subsidence predictions for the proposed mine.

Jan 1, 1998

By Emil B. Milosavljevic

Problems associated with distillation and other classical methods for analyzing operationally defined cyanide (CATC, WAD, Total and Free Cyanide) will be discussed. These methods often achieve incomplete, species dependent cyanide recoveries and suffer from serious interferences. Depending on the relative concentrations of interferents and other matrix constituents, underestimation (ultimately Type II errors probability of not detecting a constituent when it is actually present) or overestimation (ultimately Type I errors -probability of deciding a constituent is present when it is actually absent) of the cyanide levels present in a ,given sample may occur, causing in the first case false security and in the second case, excessive cyanide treatment costs. Mahy, if not all, enumerated problems can be solved by using novel flow injection (FI) gas-diffusion amperometric methods. A modification of the recently approved FI ligand exchange (FIILE) method for determination of available cyanide (USEPA Method OIA-'l677) that obviates sulfide interference will be discussed. Eight laboratory round-robin data obtained for the FI UV -digestion (FIIUV) method that determines total cyanide (Proposed Method OIA-1678) will also be presented. In addition, some methods for cyanide speciation will be presented. Finally, research needed for developing reliable methods for determination of operationally defined cyanide in solid samples will be summarized.

Jan 1, 1998

By S. Ozbilen, B. Erdogan, M. Erdogan

To study by thermal analyses the response of precipitation hardenable alloys of Al-Cu-Mg and Al-Li-Cu-Mg system to natural and artificial ageing, a series of ternary and quaternary Al-alloys with nominal compositions of Al-l.13wt%Cu-0:65wt%Mg (alloy-I), Al-1.15wt%Cu-0.57wt%Mg-0.07wt%Li (alloy-2), Al-l.19wt%Cu-0.56wt%Mg-0.75wt%Li (alloy-3), Al-2.0lwt%Cu-0.89wt%Mg (alloy-4), Al-2.14wt%Cu"0.56wt%Mg-0.07wt%Li (alloy-5) were used in the present investigation. Samples in the form of rolled sheets are subjected to water quenching at 25EC after solution treatment at 530EC for 20 min. Alloys were aged naturally at room temperature (25EC) up to 2 months and artificially at 190EC up to 2 days. By using differential scanning calorimetry (DSC) in the temperature range of25-300EC, differential thermal analysis (DTA) in the temperature range of25-600EC together with Vicker's hardness measurements, the response to natural and artificial ageing of the alloys used in the present study were investigated. It was observed that in these alloys, GPB(Cu, Mg) zones [Guinier-Preston zones with Cu and Mg] do form during water quenching at 20EC following solutionizing heat treatment. Natural ageing of the same alloys causes formation of more GPB(Cu, Mg) zones, which results in hardening in the alloys. Artificial ageing at 190EC up to l day results in GPB zone dissolution causing preliminary decrease in hardness values while two days of artificial ageing in the alloys cause S' (Al2CuMg) precipitation confirmed by DSC/DTA analyses resulting in an increase in hardness values. Li addition up to 0.75wt% helps T1 (Al2CuLi) and T 2 (Al6CuLi3) phase formation together with S' precipitation as DSC/DTA analyses show after the same heat treatment.

Jan 1, 1998

By Dan Eyde

Low levels of thallium were detected in the mine water drainages, and process water discharges of western mining and smelting operations. This required remediation under state regulatory standards, which allow discharges of no more than .0017 ppm thallium in mine water discharges. Influent streams containing thallium can be mitigated to state discharge standards after a single pass through the series of fluidized upflow columns. Test work to determine the optimal flow rates used pilot scale systems at two separate locations treating 5 - 25 gpm of effluent. The test system at the gold mine mimics the full-scale system, which will be based on the existing upflow carbon tanks that have been converted to zeolite columns. The system installed at ASARCO's East Helena smelter has a far more complex influent stream with a high loading of competing cations. Nevertheless the columns filled with CABSORB® are successfully mitigating the thallium contamination. CABSORB® ZS500RW is a product based on the sodium analog of the zeolite mineral chabazite named herschelite.

Jan 1, 1998

By E. Fockedey

he destruction of free cyanide on a Co3O4 doped carbon felt was studied. The experiments were done with an eiectrochemical filter press cell on dilute alkaline solutions containing 250 mg/l NaCN. No chloride ions were added to the solutions. The cobalt oxide protects the felt against corrosion and has a catalytic effect on the degradation of the cyanide. This kind of electrode allows working with current density as high as 1200 Aim without any visible degradation of the felt. The most interesting results were obtained with a current density of 400 Aim' at which the cyanide concentration can be lowered to 5 mg/l with a current efficiency of more than 70 % and a specific energy consumption of about 10 kWh/ kg CN.

Jan 1, 1998

By Roy A. Imbsen

Following the 1989 Loma Prieta earthquake, California Department of Transportation (Caltrans) expedited an effort to evaluate and retrofit important state-owned toll bridges to en­hance performance of the state's transportation systems during and after major (credible) earthquake events. Imbsen and Associates, Inc. (IAI) along with their sub-consultants, were awarded a contract to conduct seismic evaluation and to develop retrofit design for Benicia-Martinez Toll structure, to meet a "Serviceable" performance requirement after the event of a "Safety Evaluation Earthquake." This paper describes the design and construction specifications for the deep foundations supporting the main spans of the Benicia-Martinez Bridge. Benicia-Martinez Toll Structure (George Miller Bridge), a high-level deck-type welded truss bridge with welded girder approach spans, carries Interstate Route I-680 over the easterly end of Carquinez Strait near San Francisco, CA. The nearly 5000 ft long main truss structure consists of ten spans, ranging from 330' to 528' in length, supported on cellular reinforced con­crete pier structures. Foundation systems across the waterway, consist of cellular reinforced concrete footings, supported by groups of 6' diameter, concrete filled, steel caissons, resting on 5' deep rock sockets, at depths of 50' to 150' below the water level. Seismic evaluation of the existing foundation systems accounted for spatially varying ground motion along the length of the structure, variability of foundation material strength (i.e. at bed-rock), variation and effects of scour depth on the performance of the foundations, and dy­namic soil-structure interaction. Performance of caissons beyond their elastic strength, as well as their effects on the behavior of the foundations and substructures were evaluated and considered in establishing foundation vulnerabilities. Several retrofit strategies were considered leading to a final retrofit strategy to strengthen end connections of existing caissons, as well addition of new caissons to provide adequate lateral force resistance for the foundations. Final design package includes specifications as well as construction methods and requirements for existing and new caissons, under traffic, and pile load testing procedures for design loads of up to 12500 kips per caisson.

Jan 1, 1998