Search Documents

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

By D. Eugene Rannels, Sarah E. Dunsmore

"Dunsmore, Sarah E., and D. Eugene Rannels. Extracellular matrix biology in the lung. Am. J. Physiol. 270 (Lung Cell. Mol. Physiol. 14): L3-L27, 1996.-The lung and other organs are comprised of both cellular and extracellular compartments. Interaction of these components modulates physiological function at the organ, cellular, and subcellular levels. Extracellular components in the gas-exchange region of the lung include both noncellular interstitium and basement membranes. Connective tissue elements of the interstitium in part determine ventilatory function by contributions to tissue compliance and to resistance of the diffusion barrier. The basement membrane underlies cells of both the alveolar epithelium and the capillary endothelium; basement membrane components exert biological effects on adjacent cells through receptormediated interactions. This review emphasizes current knowledge concerning the composition and biological activity of extracellular matrix in the alveolar region of the lung. Matrix synthesis and turnover are also considered. Directions for future research are suggested in the context of current knowledge of the lung and other model systems. EXTRACELLULAR MATRIXEXTRACELLULAR MATRIX is a general term that encompasses components of the basement membrane and interstitial connective tissue. The extracellular matrix has many functions. It provides structural support, compartmentalizes tissues by separating epithelium or endothelium from interstitium, and serves as a physical barrier. Both in vivo and in vitro studies show that extracellular matrices also affect cell shape and function. The matrix elicits a variety of cellular responses, including adhesion and spreading, changes in cytoskeletal organization and differentiation, formation of focal contacts and stress fibers, stimulation of proliferation and migration, induction of polarity and gene expression, alterations in metastatic activity, and outgrowth of cell processes (for review see Refs. 387, 462). Cellmatrix interactions play roles in embryonic development and organogenesis (for review see Refs. 1, 91), in wound healing (for review see Refs. 145, 327), iri metastasis (for review see Refs. 430, 431), and in angiogenesis (for review see Refs. 185, 186). The extracellular matrix is the subject of a large volume of literature. In 1994, over 1,000 articles contained extracellular matrix in the title or abstract. After a brief discussion of key aspects of extracellular matrix biology, this review will focus on the extracellular matrix of the lung."

Jan 1, 1998

By Geoffrey S. Plumlee

The Summitville gold mine, located in southwestern Colorado, received tremendous publicity in the 1980's and 1990's for leaks of cyanide solutions from its heap leach facility. As is typical with cyanide spills, real time, geochemically rigorous assessments of the environmental effects were not performed. Past United States Geological Survey (USGS) research used simple mixing experiments to model the influx of alkaline cyanide heap leach solutions from Summitville into a nearby stream, whose waters were highly acidic due to severe acid-rock drainage (ARD) from the mine. These experiments indicated WAD cyanide rapidly degraded due to formation of Fe-Cu-CN solids and lesser HCN volatilization. The alkaline heap leach solutions also precipitated hydrous iron-and aluminum, oxides and hydroxysulfates (iron and aluminum 'supplied by the acid. rock drainage (ARD]), which then sorbed copper and other heavy metals from the ARD. These results indicate that mixing of cyanide heap leach solutions with ARD may be a cost-effective remedial method at mine sites where treatment of both is required. New experiments are currently in progress to further refine a potential remedial process.

Jan 1, 1998

By S. Rajendran

The area of the Exclusive Economic Zone (EEZ) of India is about 2.014 million km2 and the resource evaluation of placer deposits is one of the objectives of Government of India. Placers are detrital metallic minerals found on beaches and in the near shore areas. Quantitatively more important are placer deposits of light heavy minerals such as zircon, ilmenite and rutile. Rivers and other drainage channels are the main carriers of the placers which contain heavy minerals like magnetite, ilmenite, garnet, zircon, monazite, rutile etc. The present beach as well as part of the shelf was land during Pleistocene as a result of the world wide lowering of the sea levels. The coast line shifted a number of times. Hence, the heavy mineral placers on the beaches are expected to extend to offshore areas chiefly with Pleistocene lowered sea level strands. India has extensive deposits of heavy mineral placers along the beaches. Placer deposits of heavy minerals occur in discontinuous patches on the beaches along many parts of the east and west coasts. Along the central west coast of India (12??N - 19? N lat.) the placer containing 14 - 17% ilmenite form an estimated reserve of 4 million tons. On the Ratnagiri coast of Maharashtra, the proportion of heavy mineral varies between 54 and 70% in the bulk samples, consisting mainly of 14 - 39% magnetite and 16 - 30% ilmenite. The National Institute of Oceanography (NIO) surveys show that the sediments off the central west coast consist largely of silty sand, sand silt and clay. The core samples show that a reddish brown clay overlay olive gray clay which in turn overlay heavy mineral rich sands. The heavy mineral concentration ranges upto 90% and has mainly ilmenite and magnetite with minor quantities of apatite, rutile, zircon, kyanite etc. Siddiquie et al. reported 42 - 75% TiO2 in the ilmenite.

Jan 1, 1998

By C. F. Feng, L. Froyen

"In-situ processes have emerged as new and promising techniques for metal matrix composite fabrication. They offer significant technical and economic advantages over conventional processing. One of the in-situ processing routes that have been used is reactive free sintering of a mixture of powder reactants. However, materials synthesised via this route are always porous because of density differences between reactants and products. An example are the porous Al/(TiB2+Ah03) MMCs obtained by heating powder mixtures of Al+ Ti02+B with Ti02 and B in stoichiometric ratios for forming TiB2• In this study, porous Al/(TiB2+Ah03) composites were further processed by hot-pressing at temperatures above 600°C. This processing cycle was designed so that the composites could be densified. Furthermore, the reaction kinetics of the in-situ processing are studied by means of DSC analysis measured at different heating rates. The activation energies of the three intermediate steps that are involved in the reactive processing for preparing AV(TiB2+Alz03) MMCs are determined to be 923 kJ/mole, 241 kJ/mole and 235 kJ/mole respectively.XRD proved that the hot-pressed products consist of Al, TiB2 and Al203- Properties of the products are assessed by microstructural characterisation (LOM, SEM and EDS), microhardness, Young's modulus and bending tests. The results show that good microstructures, elastic properties and strengths, as well as acceptable ductilities were achieved. For the composition 79.74wt% Al-15.95wt% Ti0z-4.31wt% B, after the reactive free-sintering and hot-pressing cycles, Young's modulus is 105 GPa, bending strength is 509 MPa and maximum strain is 5.0%; for composition 88.73wt% Al-8.87wt% Ti0z-2.40wt% B, they are 89 GPa, 311 MPa and 8.2% respectively. It can be seen that the properties of products can be tailored by adjusting the relative amounts of reactants in green samples. Furthermore, for comparison reasons, Al and a binary system Al-Ti02 were identically processed as the ternary systems. Their microstructures and properties were studied."

Jan 1, 1998

By Larry Howe

Second, or retreat mhng with Mobile Roof Supports (MRS) has now been part of coal mining in the United States for a decade Their utilization has evolved into mining applications which vary in seam heights from 38 inches to 170 inches, and overburden depths from outcrop to beyond 1200 feet This paper will detail the pillaring plans, lift sequences, and mnchky utilized in these operations and the rational for the plans A comparison of the current productivities achieved will be outlined

Jan 1, 1998

By R. L. Grayson

In 1995, Congress abolished the Bureau of Mines in the Department of Interior but preserved the safety and health research functions being performed at the Pittsburgh and Spokane Research Centers. These functions were transitionally housed in the Department of Energy before permanently merging with the National Institute for Occupational Safety and Health (NIOSH), Department of Health and Human Services, in October 1996. Since the merger of the former Bureau with NIOSH, there has been an active evaluation of ongoing research activities, significant interaction with stakeholders, and the development of a process leading to "data informed" priority setting. This presentation will review current surveillance information concerning the level of injury and disease from mining work and will discuss how research priorities are evolving to improve the contribution of research to the prevention of injury and disease.

Jan 1, 1998

By Corby G. Anderson

In the majority of industrial operations recovering gold and silver by hydrometallurgical means, cyanide is the predominant lixiviant. However, as an economic alternative, production of massive quantifies of silver chloride was done on an industrial scale in the nitrous-sulfuric acid pressure leaching of a refractory precious metals concentrate. This proven process required no cyanide. Thus, because of the large volumes encountered during day-to-day plant operation, the need for efficient and low cost methods of silver chloride precipitation, reduction and materials handling was mandatory. As such, this paper covers the evolution of plant scale precipitation, filtration, washing, reduction and control of silver chloride processing. As well, an in-depth description of the unique leaching system is included.

Jan 1, 1998

By Hideki Shimando

Periodic weighting and windblast which are caused by the dynamic effects of overburden in a longwall panel significantly affect longwall mining This study describes past experience with wind blast at Miike Colliery, proposes a new loosening system using hydraulic fracturing and moistening, and also discusses strength deterioration in hard-to-collapse roof rocks due to water in order to solve the problems caused by the effects of dynamic roof rocks behavior in a longwall face

Jan 1, 1998

By I T. Cameron

The commercial production of copper metal involves a sequence of purification stages. One step of this process eliminates bulk quantities of iron and sulphur from matte Cu2S(FeS to produce blister containing 95.5 per cent copper. This task is traditionally performed in the Pierce-Smith converter, a cylindrical vessel in widespread use throughout the copper industry. Typically, multiple Pierce-Smith converters are arranged along an aisle, simplifying material transfer from vessel to vessel. Materials are moved through the aisle in pots and boats, using overhead cranes. In terms of the overall process, the converter aisle represents a critical processing unitùit contributes significantly to the value added nature of the metal. The aisle is subject to significant process disturbances. Thus, improvements in the operationÆs modes and conditions have a direct impact on process profitability. As with any commercial operation, improvements are always sought to increase process performance. The general approach involves process modelling, followed by an application of control and optimisation theory to this model. The results of such a study are then applied to the real process, leading to improved performance.

Jan 1, 1998

This paper focuses on two sites in the Mount Pleasant - McCormacks Bay area of Christchurch where residential development has taken place either within or immediately adjacent to former quarries for the extraction of volcanic rock. At the Quarry Road site less overburden was dumped on adjoining land around the turn of the century, and c.1980 dwelling and related construction took place on approximately 6 m of relatively loose fill material without the recognition of its presence or geotechnical characteristics. Subsequent settlements led to abandonment of a swimming pool and the underpinning of the 3-storey architect-designed house, whilst litigation brought by the owner resulted in findings of negligence against both the architects and engineers. At the Tramways Quarry site the Council approved subdivision of the former quarry area in the early 1980s without requiring any geotechnical evaluation of batter stability or related issues. During development it became apparent that significant blast damage had occurred to rock faces, necessitating a variety of remedial measures, and that waste materials had been dumped down faces without regard to long-term stability. Both case studies confirm the requirement for careful documentation of former quarry sites by territorial local authorities as part of their administrative function, and for detailed engineering geology and geotechnical evaluation of such areas prior to any residential use of the land.

Jan 1, 1998

By Liu Wenyong, Huang Yucheng, Yang Ba

High-water rapid-solidifying material, called æhigh-water materialÆ, is a new material developed by the authors over many years. The material can solidify nine times its volume of water into solid. The material is a fine kind of binder with special properties. The solidifying body of high-water material with water has quite a high early strength. The compressive strength of the material within three days can reach the same strength as conventional Portland in 28 days. One ton of the material can replace three tons of conventional Portland cement as binder. Some important achievements have been made in application of high-water material. In metal mines, based on the material, a new full-tailing cemented backfill technology has been developed. The characteristic of the new technology is that high-water material is used as binder and full tailing or alluvial sand is used as backfill aggregate. Because of the application of the new technology, major technical problems in backfill technology such as classifying of tailing, dewatering, transportation of pulp, low strength of backfill body, environmental contamination and so on, have been solved.

Jan 1, 1998

By J. A. Finch

In this paper, the author offers a personal view of what the next 30 years holds for mineral processing. Restating that mineral processing will remain a vibrant industry in raw material production, growth opportunities in waste management are identified. The processing sequence familiar now (mining ?mineral processing ?extraction) will become more interwoven. In situ processing (i.e., milling underground) will evolve from concept to demonstration. Opportunities to exploit physical properties altered in chemical (pyro- and hydro-) processing will present themselves. In primary grinding, the path to AG/SAG milling will progress with little deviation but opportunities in regrinding are wide open. Flotation will see the trend to designing bubble/particle reactors accelerate simultaneously with a vigorous response from mechanical cell suppliers. Gravity separation remains a bastion of the lone inventor but this author anticipates that the new lines will come from the waste management business. The paper concludes with the examination of the “research cycle” and identification of growth in small “high tech” companies and university research centres

Jan 1, 1998

By Yajie Wang

Traditionally, roof falls are usually attributed to bad roof strata and high vertical stress related to the overburden depth. However, roof falls under shallow overburden depth are oflen caused by a high horizontal stress field. Recent studies have proven that the high horizontal stress field, if existing, plays a major role in roof stability. Also the roof conditions are related to the entry diredions under a horizontal stress field. Questions are: How to orient the entry to a favorable direction to prevent the roof falls? If the entry cannot be oriented, how to support it? Through a case study in mine A, this paper analyzes the horizontal stress effect on roof stability. The guideline for the entry orientation is given based on the results of analysis. Additionally, suggestions are made for those entries that cannot be oriented to a favorable direction.

Jan 1, 1998

By I Cameron

Simulation is increasingly being used to analyse mineral processing operations and explore efficiency options. Engineers that use simulation are rightly concerned with the quality and applicability of the underlying models. However, many of these models have a significant empirical component, and the best structure for this component may not be apparent. There is an opportunity to improve the quality and application range of these models by exploring potential structures for this empirical element. One approach to this problem is the use of structural optimisation, which is a formalisation of the model development process. This method searches through a family or hyper-structure of candidate models for a model that is optimal with respect to some measure of model quality. This method has been applied to the modelling of an industrial flotation circuit. The result was a model that was a significant improvement over a number of standard models reported in the literature. Structural optimisation provides a method to compare potential models in a systematic and efficient way, and hence to improve the structure of process models.

Jan 1, 1998

By Roger G. Sprague

With the passing of time, changing marketplaces and years of hard service, coupled with new machines, increased productivity, rapidly improving technology, equipment which used to be the latest in modern mining have now slipped into obsolence. Mining companies need reliable, productive equipment in order to compete in today's market. In Western coal mining, as coal seams become deeper, older equipment must be replaced with that which can do the job more efficiently.

Jan 1, 1998

By A. Coulombe

"RésuméL’analyse des séquences d’exploitation, actuellement en usage pour les gisements très inclinés, a démontré qu’elles ne sont pas toujours optimales du point de vue du contrôle des terrains et de la concentration des travaux d’abattage (nombre de chantiers simultanément en opération). Effectivement plusieurs séquences sont très propices à la création des nombreuses zones de hautes contraintes, qui sont à l’origine des effets de pilier. L’étude de cas de la mine Lac Shortt a démontré que certaines séquences d’exploitation, actuellement en usage, ne sont surtout pas adéquates dans le cas d’un état élevé des contraintes naturelles. En effet la mine a eu de sérieuses problèmes avec le contrôle des terrains (coups de terrains et les effondrements des épontes). Ces effondrements étaient responsables de la dilution excessive et des pertes importantes des réserves minières. Les deux nouvelles séquences proposées, visent la meilleure redistribution des contraintes d’exploitation en vue d’éliminer la création des effets de pilier. En plus elles permettent une concentration plus élevée des travaux d’abattage.À notre avis les séquences proposées pourraient améliorer substantiellement la stabilité des chantiers d’abattage et par la suite les performances technique et économique des opérations souterraines. ABSTRACTThe planning of underground mining sequences represents an important aspect of the mining operation. The analysis of mining sequences actually in use for very steep orebodies has demonstrated that they are not always optimal, considering ground control and the number of stopes simultaneously in extraction. These sequences are conducive to the creation in the rockmass of several stressed zones caused by pillar effects. The case study of Lac Shortt mine showed that the sequences of exploitation currently in use are not adequate especially in the case of a high state of the natural constraints. Indeed, the mine had serious problems with ground control (rock bursts and collapse of walls). These collapses were responsible for excessive dilution and significant losses of mining reserves. The two new sequences suggested aim for the best redistribution of exploitation constraints in order to eliminate creation of pillar effects. Moreover, they allow a higher number of stopes to be extracted simultaneously. In the opinion of the authors, the sequences suggested could substantially improve the stability of working areas and, thereafter, technical and economical performances of the underground operations."

Jan 1, 1998

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998

By Frame Ritzert, Dennis Keller, Vijay Vasudevan, David Arenas

"An investigation was conducted to describe topologically close packed (TCP) phase instability as' a function of composition in the advanced ·Ni-base superalloy Rene N6. TCP phases are detrimental to overfill high-temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements. Thirty-four variations of polycrystalline .Rene N6 determined from a design-of-experiments approach were cast and homogenized at 13 l5°C for 80 hours followed by exposure at 1093°C for 400 hours to promote TCP formation. The alloys had the following composition ranges in atomic percent: cobalt 10.61 to 16.73, Mo 0.32 to 1.34%, W 1.85 to 2.52%, Re 1.80 to 2.11%, Ta 2.36 to 3.02%, Al 11.90 to 14.75%, and Cr 3.57 to 6.23%. Physical and chemical characteristics of all microstructures obtained were described using various analytical techniques. From these observations, a mathematical description of TCP occurrence (s and P phase) was generated for polycrystalline Rene N6.IntroductionNi-base superalloy single crystals represent the state-of-the-art for turbine engine airfoil application as they offer the best balance of properties to allow for the high operating temperatures required: for efficient engine operation.1 Current trends in alloy design take advantage of improved creep rupture strength with the addition .of higher levels of refractory elements. 2 In .particular, the addition of significantly higher levels of Re in third generation superalloys is key for both microstructural stability and creep rupture strength. 3 While the presence of the refractories is thought to provide strength benefits from solid solution hardening, a tendency for alloy instability in the form of topologically-close-packed (TCP) phases or secondary reaction· zone (SRZ) ·phenomena accompanies the high refractory content. 3 The formation of these phases in sufficient amount is detrimental to the overall high temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements.4 The tendency for a particular composition to form TCP may not be immediately known since the precipitation of TCP phases in Ni-base superalloys is nucleation controlled, thereby requiring long times at elevated temperatures to precipitate. 5 They preferentially nucleate along the octahedral planes of the Ni-base superalloys, usually in areas of refractory metal enrichment at grain boundaries or inside dendrites.5-6 In Rene N6, two closely related TCP phases, a and P, have been observed.2"

Jan 1, 1998

By Kiyoshi Shibata

A new assessment model has been proposed for metal production and its recycling system. The model consists of three processes, smelting of ore, cascading and upgrading of metal scrap. The present approach is to assess the total energy consumption of the system, by introducing two equations for describing the relationships between critical impurity content and the mass of production or scrap recycling. The total energy consumption in the system can be described as a function of recycling rate and performance of the upgrading process. The present model suggests that the impurity removal efficiency and yield in the upgrading process are essential to reduce the energy consumption in the systems. Especially, such points should be explicitly controlled in recycling of aluminum. The potential capability of this model was also discussed by obtaining several quantitative information required for the process design and the operational control of beneficial recycling of metals.

Jan 1, 1998