Search Documents

By Daniel Wild, Tobias Scheffer, Marvin Laugwitz, Martin Jochum

Leveling is a standard process in the rolling mill to eliminate flatness deviations. The process layout is based on models and the leveling result depends on the accuracy of the material parameters in these models. Even small deviations from the correct assumptions can have a major effect on the final flatness. Thus, after leveling the products may look optically flat, but subsequent to a final cutting process springback occurs due to residual stresses. The objective of this work is to analyze the influence of material parameters and gravity on the flatness after leveling. To evaluate the sensitivity of the process, an FE parameter study is exerted that reveals the influence of fluctuations in material properties in the case that the leveling setup is fixed. Gravity is neglected to not conceal flatness deviations. Examples of this study are rerun in a further step under consideration of gravity to also analyze its influence on the resulting flatness and residual stresses. Finally, to analyze the consequence of the residual stresses, all information of the plate from the previous step are transferred while gravity is suppressed to prompt springback. This study revealed that slight deviations of the material properties can lead to uneven plates in simulations where gravity is not considered. If gravity is taken into account, the unevenness is concealed and the plate seems flat. A springback simulation of the same plate shows that strong residual stresses are still present and would lead to unevenness if e.g. the plate were cut.

Oct 1, 2019

By HaiWen Luo, Bin Hu

A ultra-high strength medium Mn steel with good ductility was designed and manufactured via the combination of warm rolling and V alloying, which produced not only the extensive precipitation of fine VC particles in both ferrite and austenite but also the bimodal size distribution of retained austenite (RA) grains. A substantial increase of yield strength up to 650 MPa was achieved due to the addition of V without deteriorating ductility. The coarse RA grains firstly transformed to martensite during yielding at the much higher stress threshold, followed by a significant work hardening due to dislocations multiplication, twinning-induced-plasticity (TWIP) and transformation-induced-plasticity (TRIP) in the ultrafine RA grains. The best combination of strength and ductility included 1.5 GPa ultimate tensile strength and 28% total elongation. This was achieved due to the sustainable TRIP and TWIP effects in the later straining stage resulting from the ultrafine austenite grains, the latter were reversely transformed from the recrystallized ferrite grains.

Oct 1, 2019

By João Batista Ribeiro Martins, Érica Simões Rodrigues, Ramiro da Conceição do Nascimento Júnior, Marcos Tadeu D’Azeredo Orlando

In order to guarantee the quality of the sinter and process control some measurements are made such as RDI and FeO (Fe2+). However, the behavior of sinter during reduction in the blast furnace is not always understood, when it is analyzed only metallurgical, physical and chemical quality. Therefore, it is necessary to find alternative techniques to understand more this behavior. In this work four experimental trials were performed to obtain sinter samples with different FeO (Fe2+) contents. Optical microscopy was performed to identify and quantify the phases in sinter and to evaluate the magnetic behavior of each one, the Magnetic Susceptibility technique was used. The results obtained between Optical Microscopy, Magnetic Susceptibility and quality parameters were compared and then was identified that Magnetic Susceptibility may be an alternative to help the understanding of sinter behavior in Blast Furnace.

Oct 1, 2019

By Renan Bueno Wojciechowski, Yukio Shigaki

The quality of flat rolling process depends highly on multiple factors such as applied forces, materials involved for both strip and rolls, roll geometry and its positioning. To calculate the strip shape, a mathematical/numerical model can be applied, showing the final product and how the equipment behaves when changing some parameters. This is usually a time-consuming task for both user and computer, especially when it involves thin and hard strips. By coupling a quick rolling load calculation method as Bland-Ford and Finite Element Method (FEM) for roll stack deformation, it is possible to create an accurate and user-friendly rolling simulator. This paper presents the improvements done in the 3D FEM/multi-slab method and its actual capabilities by simulating two cases of a 6-High rolling mill. Different analysis in this equipment can be easily done in about 10 minutes by using the developed an electronic spreadsheet program interface and the folder generated with relevant results and logs. An operation manual and a commercial FE program plugins were made to aid construction of a completely new model. The code was created in a modularized way to assist the application of this simulator for other operational conditions.

Oct 1, 2019

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Haruki Inami, Takashi Ishida, Kazuhiro Ohara, Hiroyuki Imanari

The highly competitive business environment of the international metals industry is driving demand for more cost-effective operation of steel making facilities, rolling mills, and strip processing lines. Achieving stable operation is vital if the steel industry is to produce high-quality products constantly and productively. In recent years, advances in computer processing speeds, data acquisition rates, and data storage capacity have rapidly led to greater use of the new technologies of big data, analytics, the IoT, and AI by control system designers and process engineers, and the introduction of industrial applications. The “Smart Rolling Mill” solutions for hot strip mills have been developed by our group with the goal of achieving sophisticated, state of the art, and automated operation in steel rolling mills. The various solution engines improve process stability, increase the performance of mill equipment, and provide improved process control. These solution engines are based on extensive knowledge of the rolling process and the associated control systems. Two solution engines in particular are the diagnosis systems for rolling condition and for product quality that contribute to cost-effective operation and lower yield loss. This paper focuses on the diagnosis systems for rolling condition and for product quality in hot strip mills. Advanced information technologies using big data analytics and machine learning are applied to real-time data collected from the automation system that controls operation and the rolling process. We have developed diagnosis solutions for rolling condition and product quality utilizing predictive and clustering diagnosis. Predictive diagnosis prevents serious problems by detecting changes in the state of the plant or in the rolling condition. Clustering diagnosis classifies patterns of fluctuation in product quality trend charts, providing effective tuning guidance for improving product quality. This paper describes these applications with several examples.

Oct 1, 2019

By Henrique Lacerda Eleutério, Aldo Henrique de Almeida Barbosa, Vicente Tadeu Lopes Buono

The automotive industry’s interest in galvannealed (GA) boron steel for hot forming processes application has been steadily increasing due to its excellent surface quality, galvanic protection provided to the parts, good paint adhesion and better weldability in relation to other coatings for this application. In this study, samples of 22MnB5 galvannealed steel were heat treated and hot stamped on a water cooled die in laboratory scale. The influence of heat treatment on stability of coating and steel was assessed by using initial heating rates 11.0ºC/s and 15.0ºC/s. Microstructural evolution of galvannealed coating and structural integrity of steel during hot forming were investigated by scanning electron microscopy with energy dispersive spectroscopy analysis (SEM/EDS/Line scan), X-ray diffraction (XRD) and optical microscopy (OM). It was possible to quantify the Fe-Zn phase evolution during hot forming, to understand the effect of these heating rates on the product properties and to establish an optimized heat treatment for hot forming of these steel. The heat treatment with the heating rate of 15.0ºC/s presented greater operational flexibility and final products free from surface defects or cracks in the substrate.

Oct 1, 2019

By Eduardo Poltronieri Trés, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Anderson Denadai Thomzini

The first industrial applications of roller presses at the comminution were in 1984 in the cement industry. Since then, the equipment has taken more space in the mineral industry. However, many challenges are still present in this equipment, more specifically regarding to ore breakage predictability. The application of this equipment in the pellet feed preparation is fundamental to increase the surface area (blaine index) of the mineral using reduced energy consumption. However, even after several pressing steps, it is still challenging to achieve granulometry in percentages required for the pelletizing process. Currently these levels are reached in wet milling processes, typically carried out in wet ball mills. For the of pellets formation in pelletizing plants, both pelletizing and the firing processes requires finer granulometry. The motivation of this work is to study the pelletizing process, comparing the physical quality of the pellets produced only through comminuted ore in roller press the pellets produced in conventional comminution using circuit with ball mill.

Oct 1, 2019

By Denisio Miranda Custódio, Rodrigo Boyer, Josiane Lira Batista Haagensen, Raquel Teixeira Pereira, Felipe Viana Pimenta, Rossano Augusto Pilon Nunes

In the Tubarão Pelletizing Plants, anthracite is used as solid fuel, which has fixed carbon content of 72%. This paper will present the pilot scale results and industrial scale tests of an alternative fuel to anthracite, named Blast Furnace Dust. All the work was developed using samples from Arcelor Mittal Tubarão, due to it has a large source of production and is near to Vale/SA, which reduces significantly the cost for the material’s transportation. There was an impact on the variability in fixed carbon results of the slurry, mainly at the beginning of the test, reaching very high levels and put on risk the pellets physical’s quality. This variation can be explained by some operational disturbances and, mainly, by the low predictability of Blast Furnace Dust quality and lack of an adequate system for material preparation and dosage.

Oct 1, 2019

By Ismael Vemdrame Flores, Lindaura de Souza Cândido D’ Avila, Maurício Covcevich Bagatini, Arthur Felipe Lino Oliveira, Rafael Adriano Lopes Júnior

The use of pellet feed to adjust the chemical quality of the sinter is an alternative to the depletion of iron ore reserves. However, the addition of ultrafine in the sintering process can cause decrease of permeability and consequent drop in machine productivity. In this context, the present work investigated the addition of natural and ground pellet feed, evaluating its effects on cold agglomeration for sintering and quality of quasi-particles produced. Eight typical mixtures with industrial composition were produced in the laboratory, replacing Sinter Feed with different percentages of Natural Pellet Feed (NPF, 91% <150 μm) and Ground Pellet Feed (GPF, 83% <44 μm). The mixtures were subjected to cold agglomeration tests and the quasi-particles produced were evaluated by screening, shatter test, permeability test and disintegration into primary particles analysis. There was a decrease in the mean particle size of quasi-particles and reduce in permeability with addition of the ultrafines. The addition of NPF favored the layering mechanism in larger quasi-particles. The coalescence mechanism occurred for larger additions of NPF and GPF, being more expressive for GPF additions.

Oct 1, 2019

By Lilian Silva Costa, Laila Bonzi Ramos, Marcela Lessa de Freitas, Igor Quaresma Vianna

The eighth pelletizing plant, located at the Tubarão complex Industrial Unit of Vale S/A in Vitória-Espirito Santo-ES, processes a pellet feed primarily composed of compact and friable itabirite from Itabira and Brucutu concentration plants, located in the iron quadrangle in Minas Gerais-MG. The use of hydrated ores in the composition of the fine piles, such as Brucutu's common fines amphibolite itabirite (FABR), and Fábrica Nova pellet feed (PEFN), contributed to increase the energy efficiency of comminution, increasing the production of tumbling ball mills, minimizing the impacts during a mill preventive maintenance.

Oct 1, 2019

By Paula Maria Gomes Cunha Leão, Flávio de Castro Dutra, Fabrício Vilela Parreira, Silvio Maranha

In the iron ore beneficiation, tailings are inherent in the concentration processes to which the ores are subjected for the production of commercial products. The large generation of tailings has been motivating the study of technological alternatives for its reuse, with the development of processes that contemplate the concentration of fine ore particles present in the tailings, such as the reintroduction of these particles in the process of manufacture of the iron and steel itself, through the agglomeration techniques such as briquetting. The aim of this article is to study the technical feasibility of the production of iron ore tailings and coking coal briquettes for use in reduction reactors, through a systematic review of the literature on agglomeration, briquetting and self-reduction processes, covering the main variables that influence the production of high quality briquettes, such as binders use, binder behavior of coking coal, coal granulometry, iron ore and coal proportion, compacting pressure and temperature of thermal treatment and the effects of these variables on briquettes final properties.

Oct 1, 2019

By Davi Silva Braga, Alexssander Lopes Sampaio, Rodrigo Carneiro de Oliveira

Vallourec was world pioneer in the deployment, development and consolidation of technology for the use of pulverized charcoal as the main energy source on the first Grate-kiln pelletizing plant in Brazil. The objective of this work was to delve into the subject and to bring more information about this innovative practice of Vallourec that has been attracting the attention of other companies in the steel industry. Industrial tests confirmed the technical feasibility, taking Vallourec ahead in the project of adaptation and investment. With consolidated data of two years and five months from the beginning of the implementation, the main benefits are the average reduction of CO₂e emissions by 50%, cost reduction higher than expected and return on investment in just 19 months.

Oct 1, 2019

By Luís Marcelo Marques Tavares, Gilvandro Bueno, Túlio MoreiraCampos

The HPGR development and application in the minerals industry resulted in an important increase in its application in iron ore pellet feed processing in the last decades. Vale SA was one of the pioneers in application of the HPGR in integrated plants, currently operating with six HPGRs in the pelletizing plants of Complexo de Tubarão (Vitória, ES). The work uses the mathematical model of the HPGR, proposed by Torres & Casali and modified by the present authors, to predict the performance of two industrial pellet feed HPGR units of the Complexo de Tubarão. Besides model validation, results of process simulations are shown in order to optimize the pellet feed pressing according to industrial demands, presenting different scenarios that are more attractive to HPGR operation. Simulations showed that it is feasible to reduce the specific surface area of the HPGR feed from 1770 cm²/g to 1570 cm²/g, allowing to produce a pellet feed of the same quality in its product (1911 cm²/g) and therefore reduce the work done by upstream ball milling.

Oct 1, 2019

By Larissa Rodrigues de Carvalho Rocha, Mauro Vivaldino Fernandes, Beatriz Fausta Gandra

A composição química do gás redutor afeta, de forma marcante, sua difusividade através do leito e a capacidade de redução da carga metálica. Associado a isto, o cenário econômico e ambiental indica a necessidade de se buscar cada vez mais elevada produtividade dos altos-fornos, com baixo consumo de combustível e menor emissão de CO2. Para tanto, as empresas têm buscado operar com elevada taxa de injeção de carvão e, em casos de política favorável, intensificar o uso de gás natural em altos-fornos. Nestes casos, a quantidade de material reduzida via H2, em comparação ao CO, é aumentada. No presente trabalho, são apresentados os resultados de ensaios em amolecimento e fusão (A&F) de dois tipos de granulados, de um tipo de pelota e de um sínter industrial, utilizando-se como redutor um gás com diferentes teores de H2 (0% a 12%). Verificou-se que, para o granulado, não há uma tendência definida. Embora um maior teor de hidrogênio possa favorecer a redução, isto não refletiu em melhor permeabilidade do leito. No caso da pelota estudada, houve leve tendência de melhora nos parâmetros avaliados quando se tem o gás mais rico em hidrogênio. No entanto, seu desempenho em A&F foi muito aquém daquele esperado para este tipo de carga, uma vez que apresentou elevada resistência à permeabilidade associada à baixa redutibilidade até o início do amolecimento. Para o sínter, foi identificada evidente melhora nos aspectos de redução e de permeabilidade do leito.

Oct 1, 2019

By José Geraldo da Silveira, Luiz José Gonçalves, André Mendes Carneiro Lyrio, Raylander Rocha Pessoa, Péricles Guimarães Oliveira Aguiar, Guilherme Ribeiro do Espírito Santo, Filipe Soares Pontes

Este trabalho tem como objetivo apresentar a origem do projeto inovador do cadinho do Alto-forno 2 além do planejamento, a implantação e os resultados obtidos no Alto-forno 2 da Aperam South America após a reforma. O trabalho de pesquisa e desenvolvimento teve início em 2012 após a primeira marcha fria com conseqüente redução das temperaturas da soleira. Foram realizadas diversas reuniões, discussões e seminário sobre alto-forno com especialistas de diversas empresas. A mudança de redutor carvão vegetal para coque por seis meses serviu para comprovar parte da teoria construída pelo time da redução. Para, por fim, culminar no conceito por trás do problema do AF2 e então o novo design do cadinho que foi proposto e implantado na reforma iniciada em dezembro de 2017. Após sua implantação, conforme teorizado pelo time, uma nova gama de resultados e patamar de operação foram atingidos, comprovando diversas das teorias formuladas.

Oct 1, 2019

By Cameron Soltys, Hamid Ghorbani, Maher Al-Dojayli

Cooling staves in blast furnaces are used to minimize the process heat loads on steel shell and refractory system. Copper staves are exposed to significant fluctuating thermal loads which may lead to premature stave failures due to cracks, water leakage, bending, abrasion and resultant wear. In this paper, an assessment methodology is presented to evaluate the effect of thermal cycling on copper staves including bending, fatigue and thermal ratcheting. This approach incorporates temperature-dependent copper properties including creep and plasticity to more accurately capture inelastic deformations, damage and fatigue in staves under transient and cyclic thermal loading conditions. Root cause failure assessment and improvements to copper stave design can be assessed using the presented methodology.

Oct 1, 2019

By Flaviani Marculano Marchesi, Silas Gambarine Soares, Elton Volkers do Espírito Santo, Felipe Fardin Grillo, Heitor Cristo Clem de Oliveira

O objetivo deste trabalho é utilizar a termodinâmica computacional para estudar as propriedades de escórias iniciais dessulfurantes utilizando misturas com diferentes fluxantes: fluorita, sodalita, borra de alumínio, B2O3 e ilmenita. A princípio, as misturas foram definidas e em seguida foram realizadas simulações para o aquecimento dessas misturas a 1350 ºC por meio do software FactSage 7.2. Assim, foi calculado o fator de dessulfuração (FDeS) para cada mistura com base nas condições de equilíbrio. As misturas contendo 5 e 10% de fluorita e 5% de sodalita foram as que apresentaram maior FDeS. Em contrapartida, as misturas com 10,15 e 20% de B2O3 tiveram os piores resultados nessa análise. Misturas da literatura também foram simuladas a fim de se obter o FDeS e relacioná-lo com a eficiência.

Oct 1, 2019

By Johne Jesus Mol Peixoto, João Victor Gomes Guimarães Ananias, Itavahn Alves da Silva, Thiago Araújo Santos de Oliveira, Weslei Viana Gabriel, Carlos Antônio da Silva, Salvatore Giuliano PeixotoTropia

O arraste de escória para o distribuidor, durante a drenagem de panelas de aço, tem grande impacto no rendimento metálico, limpidez e produtividade no processo de lingotamento contínuo. Modelamento físico e matemático foram utilizados para o estudo da formação do escoamento tipo vórtice e funil no esgotamento de panelas de aço. Em um modelo em escala 1:6,5 foi avaliada a influência da vazão de drenagem, altura inicial de líquido, temperatura do banho e estratificação da temperatura sobre a altura crítica (Hcr) de formação de vórtice. Para todas as condições experimentais, o valor de Hcr se mostrou crescente com o aumento da vazão, respeitando uma relação linear. Através da técnica de Particle Image Velocimetry – PIV observou-se o desenvolvimento do campo de velocidades sub-superficiais da água durante a drenagem em modelo de acrílico em escala 1:6,5. Os resultados das simulações fluidodinâmicas obtiveram bom acordo com os experimentos físicos, e foram capazes de representar a influência da vazão e da temperatura sobre o valor de Hcr.

Oct 1, 2019

By Antonio Favia, Carsten Sowa, Spencer Diehl, Maria Carolina Campos, Christian Green, Marco Tulio, Olaf Schulz

Casting fluxes are one of the key factors to guarantee a good performance of the continuous casting process. Fluxes are added over the liquid steel in the mold, where carbon in the flux reacts with any air present, to form a reducing atmosphere of CO (g) to protect molten steel from oxidation. Then the oxide components form the sintered layer and they melt to form a liquid flux pool. Liquid slag from the pool infiltrates into the mold/strand channel and lubricates the newly-formed, steel shell. It was very common in the past that the addition of casting flux in the mold was made manually by the continuous casting strand operator, where the addition uniformity would mainly depend on the attention of the Operator in process and the addition standard would change from one operator to another, may causing variability on the continuous casting quality parameters. This paper presents improvement of continuous casting parameters such as, stability of flux thickness and reduction of dust in the continuous casting process, with the use of flux distribution mechanism in two continuous casting machines from two different steel plants.

Oct 1, 2019