Search Documents

By Paul W. Weiblen, Louis J. Cabri, Rolando Lastra

"Preliminary tests were done to determine whether comminution by electric-pulse disaggregation, or E-PD (cf. Rudashevsky et al; 1995), was more effective than using conventional crushing for Merensky Reef ore. A hand sample of the Merensky Reef was sawn in two: then one sub-sample was comminuted to .2 mm using E-PD at the University of Minnesota, and the other sub-sample was crushed to .2 mm using a conventional jaw crusher at CANMET.The products of the electric-pulse disaggregation and jaw crusher were fractionated by sieving and by a separation using a heavy liquid with a specific gravity of 3.3, because the proportion of platinum-group minerals (PGM) and sulphides to silicate minerals is very low. Thus, four mineral separates were produced: .2000 + 833 µm, -833 +208 µm, -208-µm float and -208-µm sink. All the mineral separates were studied by image analysis (Lastra et al; 1998). The main objective was to determine the liberation of gangue (silicate minerals), chromite, pyrrhotite, chalcopyrite, pentlandite and PGM. In the case of the PGM, a specific image analysis program was written to search and measure these minerals.The results show that the liberation obtained for gangue was similar (~99%) using either method of comminution. However, the liberation obtained for chromite (~89% vs. ~38%), pentlandite (~50% vs. 1%), pyrrhotite (~56% vs. ~38%), and PGM (~56% vs. ~1%) by E-PD was higher than that obtained by conventional jaw crusher, whereas the liberation obtained for chalcopyrite (~20% vs. ~71%) by E-PD was lower. Nevertheless, the image analysis of the products also showed that the PGM are strongly associated with pentlandite. Thus, for the Merensky Reef, liberation of pentlandite from the gangue minerals and chromite is important to recover more of the PGM. This maybe be significant because, in addition to increased recovery of platinum-group minerals (PGM), Merensky Reef pentlandite also contains significant quantities of valuable platinum-group elements like Pd and Rh (Cabri, 1981; Cabri 1988, Kinloch 1982, Peyerl 1983). Hence, the results indicate that for the Merensky Reef, electric-pulse disaggregation would represent a better comminution operation than a conventional jaw crusher would. In addition, the greatly improved liberation for chromite may find application for the PGM-rich UG2 chromitite."

Jan 1, 2003

"The first 90 years of the last century generated a considerable volume of technical literature on the subject of grinding mill power and its prediction. It is therefore surprising that during this time there were no published models for predicting grinding mill power draw which were validated using a wide range of comprehensive industrial scale data.Notwithstanding this lack of data, the majority of models placed limited emphasis on the internal dynamics of mills and relied on simple assumptions which considered the charge to take up a fixed position and shape.Laboratory based studies (Liddell, 1986), and industrial data (Morrell, 1993), showed that these assumptions did not hold over a wide range of operating conditions, and brought into doubt the ability of the (then) existing models to accurately predict grinding mill power draw. Furthermore no model treated AG,SAG and ball mills as a single class of devices whose power draw could be predicted with the same equations.Through a detailed investigation of the charge dynamics, coupled with a large data base of industrial mill power draws, this situation was rectified by the end of the century, by which time a model had been developed and validated, which accurately predicted the power draw of all wet tumbling mills. This paper describes this model and reviews some of the earlier attempts at mill power modelling."

Jan 1, 2003

Jan 1, 2003

By Volker Vogt, Wolfgang Sand, Eberhard Gock

"It was discovered that the selective activity of bacteria during the extraction of raw material concentrates by means of flotation could also be achieved with extracellular polymeric substances (EPS) excreted by bacteria. EPS, which is extracted by means of centrifuging bacterial cultures, can help to significantly reduce the use of cyanides, approximately 200,000 t/a of which are used for ore dressing today.The bacterium used was Acidithiobacillus ferrooxidans. In order to identify the bandwidth of the oxidation activity, 20 bacterial strains of the strain collection of the University of Hamburg were attracted to iron(II) sulfate and pyrite under defined conditions. All strains oxidized iron(II) sulfate ten times faster than pyrite.EPS has so far been derived from four strains. In general, EPS extracts are divided into a hydrophilic and a hydrophobic fraction. The hydrophilic fraction is composed of e.g. fucose, rhamnose and glucose; fatty acids such as dodecanoic acid, hexadecanoic acid, octadecanoic acid and nonadecanoic acid were found in the hydrophobic fraction.Pure mineral phases and mineral mixtures were used for the flotation tests. As opposed to current knowledge, the results were reproducible with technical flotation machines."

Jan 1, 2003

By D. Whittles, S. Kingman, S. Bradshaw, N. Miles

The influence of microwave energy at high electric field strength on ore strength has been investigated. Two ores of varying mineralogy were treated in both multimode and single mode microwave cavities. After treatment, any change in strength relative to untreated ore was established. It was shown that in the multimode cavity reduction in strength was related to the applied power level. Results of tests carried out in the single mode cavities showed that, for both ores, reductions in ore strength > 50% could be achieved in very short periods (<1 second). Thermal stress analysis showed that the mechanism of microwave induced failure was the development of tangential stresses at the grain boundaries. It was concluded that operation at 915 MHz with high power and short residence times gives feasible scale-up possibilities.

Jan 1, 2003

By Francesco Vegliò, Luigi Toro, Francesca Beolchini, Francesca Pagnanelli, Stefano Ubaldini

"Biosorption is an innovative technology used to remove heavy metals from aqueous solutions from mining waters and other industrial wastes. A wider application of this alternative process is strictly dependent on the understanding of the chemico-physical aspects involved, in order to optimize the operating conditions. Mechanistic models are the most useful tools used for understanding purposes, even if the empirical models are still widely applied for their simplicity.In this paper especially propagated biomasses of Sphaerotilus natans, calcium alginate and some waste materials were tested as adsorbents for single and binary solutions containing heavy metals at different pH. The equilibrium experimental results were fitted according to empirical and physical models with growing complexity outlining the inadequacy of the predictive models; in fact, the non-ideal interactions among metals require the insertion of additional correction parameters."

Jan 1, 2003

By R. Sharon, P. M. Hawley, X. Ochoa

"Development of Barrick Gold’s Pierina gold mine in north-central Peru requires construction of a waste dump for disposal of nonore grade materials stripped from the open pit to expose the ore. The waste dump site is located near the open pit in a U-shaped valley that is underlain by thin colluvial and morainal soils with locally thick peats and glaciolacustrine deposits. Bedrock underlying the site consists of variably weathered volcanics. The site is subject to moderately high seasonal rainfall and significant seismicity. The geotechnical quality of the waste rock is highly variable, ranging from low-quality, degradable, soil-like materials containing appreciable quantities of silt and clay, to high-quality, hard, durable, blocky waste rock.A hybrid dump design concept was developed that requires in-pit segregation of highand low-quality waste, and selective placement of materials in the dump to maximize stability and enhance internal and subsurface drainage. The design includes a rock drain beneath the dump along the axis of the valley and a series of connected finger drains. Extensive peripheral diversions and stormwater control measures to inhibit infiltration of precipitation are also included.This paper discusses the unique challenges presented by the site and waste materials, the design methodology and stability analyses, and planned monitoring systems."

Jan 1, 2003

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Grinding is one of the most energy consuming unit operations and is also a very inefficient and costly process. Therefore, it is of great importance to run the grinding process as efficiently as possible. The most common way today to control grinding processes is by measuring the power draw of the mill and try to keep it at a maximum level. However, some studies (Kawatra, 1989, Koivistoinen, 1989, Moys, 1989) have shown that this measurement doesn.t reflect everything that takes place inside a mill. Among other parameters like slurry rheology, temperature and charge behaviour, the volumetric filling of a grinding mill seems to have a large influence on the grinding efficiency (Herbst, 1988, Koivistoinen, 1992, Vermeulen, 1988). A problem in attempting to measure those parameters has been to get a sensor that is both robust and sensitive enough for continuous on-line measurement.This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a DEM modelling technique is used.The results indicate that the system is capable of following the normal variation that occurs in the mill. The signal also very well reflect changes in operating variables such as ball charge level, pulp density and rotational speed. By studying the nature and different features of the signal one can get a better understanding of milling circuit dynamics. Another feature of the technique is the possibility for an operator to continuously follow the grinding process and thereby run the process under optimal conditions."

Jan 1, 2003

By M. Salas, L. Rolf, H. Z. Kuyumcu

"Industrial use of abrasive stress takes place in the area of fine grinding and in order to clean surface contaminated soil particles. Also, at many mechanical operations abrasion emerge as an unintended side effect. At the Institute for Raw and Waste Material Processing at the Technical University of Berlin systematic investigations are carried out, to further the knowledge regarding the dependence of abrasion process on material properties and stress mechanisms as a basis for design and optimisation of the process or for its avoidance. Aim was the mathematical description of the abrasion process running with a single particle stress. For the purpose of investigations an agitation cell was used. Limestone served as material.In the presented work the influence of particle diameter, particle shape and collision energy on the mass and particle size distribution of abrasion debris was studied. The surface geometry of the particle was characterised by the particle shape factor ?x and the particle diameter dp. The particle shape factor ?x stays in direct relation with the abrasion degree x, and can be substituted by a mathematical function of x.Physically the particle shape factor ?x can be interpreted as a proportion of abrasive stresses splitting up complete crystals and crystal fragments. These two different mechanisms depend on different ratios of curvature of the surface of the stressed particle. The abrasive stress of strongly curved surface areas leads to separation of complete crystals. The abrasive stress of weakly curved surface areas leads to separation of crystals fragments. Accordingly the mass of wear mAb and median diameter of the abrasion debris d50 are different. The derived mathematical relations consider this behaviour by the particle shape factor ?x , which represents the ratio of the mixture of both stress mechanisms. The dependence of the particle shape factor ?x on the abrasion degree x with an exponent approximately to 2/3 points out that the particle shape factor ?x represents a surface area relation."

Jan 1, 2003

By Takashi Furuyama, Sukeyuki Mori, Ltd. Kyushu Metal Industry Co., Abel Bissombolo, Yoshitsugu Koga, Masamichi Hata

"Actually, the recovery of valuable metals such as iron, aluminium and copper is a nowadays practice in factories dealing with the processing of scrapped automobiles (Harder (WERG); Koga et al., 1997). This process has reach a recycling rate of about 75%, and generates a huge volume of waste (including cottons, sponge, plastics, rubber, etc…), locally known as “shredder dust”, which is commonly dumped on landfills; its recycling is either unsatisfactorily or not yet performed (Keller and Schebdat, 2000).The saturation and depletion of valuable disposal sites in the not-so-distant future, as well as the social and environmental problems related to the accumulation of these residues disposals are a major challenge for the automobile shredding industry.To promote an alternative way for the management of these disposals, the authors have initiated and developed a system for their processing, on the basis that more than 90% of these residues are combustible materials that could be used as refuses derived fuel. The developed processing system points out the mechanical/physical separation of a calibrated (–80+5mm) shredded automobiles residues into two streams by means of an ascending airflow passing through a vertical zigzag separator and, the compaction of the light-weight materials (that is about 60% of auto shredder residue recovered as float products and mainly composed of cotton, sponges and light plastics) to form a refuse derived fuel (RDF), the density, calorific value and ignition loss of which are 1.19 g/cm3, 4470 kcal/kg and 60.7%, respectively. A sedimentation tank is used to recover the light-weight materials deported in the heavy fraction stream."

Jan 1, 2003

By T. S. Golosinski

The paper reviews current status of online education related to mining, and reports on the online Master of Engineering programme in Mining Engineering that is offered at the University of Missouri-Rolla since 2001. Keywords: Online education, learning, teaching, mining engineering, mining education online

Jan 1, 2003

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By Kal Sastry, Anshuman Prasad

This paper presents a population balance model (PBM) for describing the agglomeration process and select a suitable coalescence kernel that can simultaneously describe nucleation, layering and coalescence mechanisms. The PBM is solved numerically by making use of a size discretization procedure in order to simulate iron ore agglomeration in rotating drums where moist feed is added to preformed seeds. Subsequently, a comparison of computer simulation results with the previously published experimental data is provided. Finally, the paper discusses how the current approach can be further extended to the simulation of industrial iron ore agglomeration circuits operated in closed circuit.

Jan 1, 2003

By Andrew T. McBride, Malcolm S. Powell, Indresan Govender

"Current empirical Semi Autogneous Grinding (SAG) mill models contain assumptions concerning the amount of energy available for particle breakage, how this energy is distributed in the mill media and the rate at which the energy is transferred. Despite these assumptions the JK SAG model is highly functional with a proven track record. DEM provides a numerical framework to greatly improve on these assumptions that were necessary due to a lack of available input data.This paper identifies key outputs of the Discrete Element Method (DEM), such as energy spectra and impact probability distribution. It describes how they can be incorporated into current mill models utilising practical rock breakage data. The rate at which energy is transferred is shown to be dependent on particle position and mill rotational speed and not once per cycle as previously assumed. Based upon this an improved energy transfer methodology is presented. The fundamental outputs of the DEM are validated against experimental three-dimensional particle tracking data, so as to establish whether the DEM produces correct energy transfer predictions on the inter-particle level, which is crucial to this work."

Jan 1, 2003

By Aziza A. Yousef, Suzan S. Ibrahim, Mahmoud A. Arafa, Mohamed A. Abdel Khalek

In view of the shortage of soft water all over the Middle East countries, seawater may be used to replace the fresh water in flotation beneficiation. The flotation process required about 7 m3 of fresh water/ ton ore. This article aimed to study the effect of seawater cations and anions on the flotation process of four important mineral commodities. The adsorption of collector, zeta-potential, zero point of charge and floatability of pure minerals were studied. The individual effects of different cations and anions that are predominant in seawater, within their more or less actual concentrations were studied on individual mineral and on groups of them. The troublesome Ca2+ and Mg2+ ions, in the anionic circuit could be controlled by soda ash addition to the pulp before the anionic collector. The addition of sodium silicate improved the floatation selectivity of mineral mixtures and natural ore. At the optimum conditions the calcareous phosphate ore yielded a concentrate recovery of 83% with a grade of 34% P2O5, with 0.61%MgO, which from an ore assaying (25.3% P2O5 and 9.4% MgO).

Jan 1, 2003

By David Dreisinger

"The leaching of base and precious metal ores and concentrates continues to progress in both laboratory study and industrial application. These developments are being driven by the need to respond to difficult ores and concentrates that are not amenable to conventional treatment. In many cases alternatives are being developed to conventional treatment (e.g. Pyrometallurgy) for technical and economic reasons.In this paper, a brief general review of some new developments in leaching will be followed by a more detailed explanation of three process developments that have either been industrially applied or are expected to be applied in a short time frame. The three processes to be reviewed in detail are the Mt. Gordon Copper Process, the Anglo American Corporation/University of British Columbia Copper Process and the PLATSOL Process. These leaching processes operate at low (90°C), medium (150°C) and high (220°C) temperature and are successful in quickly and completely extracting metal values from ores and concentrates."

Jan 1, 2003

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed. The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grad~, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the fmal cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure 1."

Jan 1, 2003

By Hong Nguen Vu, Pavla Ovcarí, Peter Fecko, Barbara Tora

The aim of this paper is to evaluate the suitability of a coal sample from the mine Jaworzno (Poland)- locality for bacterial leaching. Laboratory research used a pure bacterial culture of Thiobacillus ferrooxidans. The results showed that bacterial leaching was effective, with a one month leaching time, when 65% of total sulphur and 85% of pyritic sulphur was leached. The paper describes changes to the pyrite during and after bacterial leaching.

Jan 1, 2003

By Emile Scheepers, Chris Aldrich, Jacques J. Eksteen

The pneumatic injection of CaC2 powder into molten iron has become a very reliable and effective way to carry out desulphurisation. The key variables that influence the kinetics of this process are the condition and composition of the top slag, the oxygen activity in the hot metal and the injection conditions. Notable injection parameters include carrier gas flowrate, reagent flowrate, lance depth and initial sulphur concentration. A one-dimensional, steady-state model for momentum, heat- and mass transfer in rising gasliquid- powder plumes was developed for conditions relevant to the CaC2 refining process at Saldanha Steel?, South Africa. Combined with a model that predicts the contribution of the topslag to the process, the overall rate of desulphurisation as a function of time was determined, thereby quantitatively demonstrating the influence of the above-mentioned injection parameters on the kinetics of the desulphurisation process.

Jan 1, 2003

By H. Tiefel, M. Schneider, T. Neesse, J. Regler, J. Dueck, F. Donhauser

In practice the advantages of high-quality hydrocyclone separation are often reduced due to varying feed suspension properties, solids concentrations and particle size distributions. Control systems of large hydrocyclones are usually fitted with controllable underflow nozzles, which is not practical for small hydrocyclone batteries. Therefore, a new control system for a battery of hydrocyclones with a nominal diameter of 150 mm was invented at the LUR in cooperation with AKW Apparate und Verfahren GmbH & Co. KG. This process was developed for bentonite slurry regeneration associated with tunnel excavation using bentonite slurry as a transport aid and lubricant.

Jan 1, 2003