Search Documents

By J. F. Archibald

A research effort has been undertaken, under Workplace Safety and Insurance Board of Ontario (WSIB) sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials [thin, spray-on liners (TSLs)], typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and bolt-and-mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field-scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen’s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validate that thin, spray-on linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

Jan 1, 2004

By N. N. Malila, N. R. Shoko

The ever-increasing pressure on the profit margins of ferro-chrome producers and the gradual depletion of deposits of rich hard lumpy chrome ores calls for the ferrochrome industry to maximise the use of fine fractions of concentrates and friable chromite ores. Zimbabwe is endowed with huge deposits of refractory and friable ores that occur on and off the Great Dyke complex. The conventional metallurgical process of smelting of chromite ores in submerged arc furnaces is favoured by the use of refractory hard lumpy ores. The requirement to use all lumpy ore has been circumvented to a large extent at Zimbabwe Alloys. The use of briquetted chrome ore fines in the production of Ferrosilicon Chrome and High Carbon Ferrochrome has yielded positive results over a period in excess of twenty-five years. Of the three industrially used methods of agglomeration of chromite ores; sintering, pelletisation and briquetting, briquetting is preferred because the other two are associated with higher capital and operational cost. Zimbabwe Alloys has developed operational and technical expertise on the briquetting and utilisation of chromite ore fines and concentrates. Variations in the quality of available chromite ore fines imply that their amenability to briquetting is a dynamic problem. Appropriate briquetting parameters to guarantee quality briquettes are essential to the successful use of briquetted chromite ore fines. In developing a technology for briquetting of chromite ores, it is important not only to study the mineralogical and grain-size characteristics of the chromite ore fines but also to make an informed choice of the type and quantity of the binder and the conditions for producing a physically and chemically competent green and cured briquette. This paper discusses Zimbabwe Alloys' experience on the briquetting process and the advantages derived in the smelting of the briquetted chromite ore fines in comparison to the use of conventional lumpy chromite ore with respect to improvements in chromium recovery and as a consequence related efficiencies and unit cost of production.

Jan 1, 2004

By R. T. Jones

Slags have been produced as by-products from pyrometallurgical processes for thousands of years, and have generally been regarded as waste. Many of these slags are no longer seen as residues merely to be discarded, but as potential economic sources of metals, or as useful by-products in their own right. Slag cleaning can enhance the recovery of valuable metals in existing pyrometallurgical processes, or can produce economic value from recycling old slag dumps. For example, a process has been developed and implemented industrially for recovering cobalt from copper smelting slag in a DC arc furnace. The relatively non-leachable behaviour of glassy slags allows them to be used as a very safe means of disposal of metallurgical waste streams, including many that are classified as hazardous. The high temperatures, reducing conditions, and good mixing that can be achieved in a DC arc furnace enable the effective functioning of this environmentally beneficial means of disposal. Lead blast furnace slag can be rendered safe for disposal by treating it using the Enviroplas process, which strips most of the hazardous lead from the slag (and traps the rest in an insoluble glassy slag) and recovers economic quantities of zinc by absorbing (in a lead splash condenser)the zinc vapour that is fumed off in the furnace. Another example can be seen in the recovery of a chromium- and nickel-containing alloy from stainless steel plant dust, while producing a disposable residual slag. The examples presented here illustrate that it is possible to develop processes that are both economic and environmentally beneficial. Keywords: DC arc furnace, plasma, slag cleaning, cobalt recovery, zinc fuming, Enviroplas, jigging, re-melting fines, environmental, economic

Jan 1, 2004

By Craig Byington

The stress-field orientation mapping and analysis (SOMA) technique for determining the operative stress field near mine workings and its relationship to various fracture sets is described using Dickenson-Russell Coal Company's Laurel Mountain mine as an example. Carried to its practical application, this technique ultimately defines the optimal orientation for the mine workings wherein pillars, rather than rock bolts or other roof support methods, dominantly shoulder support of the highest-probability, potential, roof-fall blocks. It also provides a predictive tool describing local variability in rock deformation and in secondary roof support methods. Fracture discontinuities within a rock mass, either as pre¬existing natural fractures or as mining-induced fractures, are uniquely necessary for every brittle-deformation ground failure including roof falls. Prediction and mitigation of roof falls requires quantifying the interaction between the fracture sets and the operative principal-compressive¬ stress-axis orientation (olo). The SOMA technique utilizes the interaction between fractures and 61o, specifically their dilation or closure, to calculate the orientation of 610, and to estimate the orientations of 62o and o3o. A stereonet program is used to organize and statistically analyze the fracture data, and then to determine the optimal orientation for the mine workings. The final step in the SOMA technique involves modeling the Laurel Mountain mine using a 2-D, finite-element, modeling program. This assures that the interpretations regarding the optimal working orientation closely match the deformation features observed in the mine. It also provides a predictive tool describing highly variable stress and strain partitioning, seemingly erratic rock-bolt failures and the interactions between different sets of mine workings within different coal seams. The critical importance of including the fracture sets is well illustrated in the Laurel Mountain mine where the effects of earlier mining of an underlying seam is contrasted in both a fractured and otherwise identical non-fractured model to illustrate the consequences of ignoring fractures in a predictive roof-fall model.

Jan 1, 2004

By J. H. Zietsman

It has previously been observed that industrial high-titania slags display a compositional invariance, remaining close to stoichio-metric M3O5. The present study focuses on this invariance and the phenomena which may cause it. The invariance was studied using thermochemical calculations and a mechanism is proposed for the observed behaviour. The mechanism suggests that a combination of thermochemical equilibrium and transient slag solidification and melting results in the observed compositional invariance. The proposed mechanism provides new insights and prompts questions about other mechanisms in the smelting process.

Jan 1, 2004

By M. Ramulu, A. K. Chakraborty, P. B. Sahu, C. Bandopadhyay, P. B. Choudhury

Human response to blast induced vibration and air overpressure is an unsolved problem that accompanies excavation process in mining. Pre-assessment and understanding of annoyance due to production blasting is probably one of the most important aspects of a successful mining operation. Complaints arising due to unoptimised blasts lead to various critical situations that hamper production. Inspite, this important aspect has been covered by a limited number of researchers in the world and probably least in Indian context. Human response is a complex phenomenon and the sensitivity of individual also vary from person to person depending on various factors like age, sex, literacy, health and exposure to mining. With ever increasing demand of minerals, opencast mines are expected to approach habitats and thus mine management may witness increased response to blasting. Many developed countries have their own guidelines based on scientific analysis, addressing such environmental problems, where as there are a few studies available in India. This study introspects above phenomenon in tune with mining requirements by analysing direct human response. This paper is based on a case study regarding the human response to blast induced hazards in a Manganese mine situated in central India. Advanced techniques of Critical Path Method and Multiple Response Analyses have been used to unearth important inferences on the response of different crosssections of population residing about the mine to blast induced noise, ground vibration and air overpressure. Various inferences drawn may provide guidelines to the planners, environment or safety departments and blasting official for safe and environment friendly blast design.

Jan 1, 2004

By K. Saito, Y. Miyauchi, T. Nishi, Y. Kizu

At Tokushima Plant of Nippon Denko Co., Ltd. high-carbon ferromanganese is produced by the electric furnace method using lump manganese ores and sintered manganese ores manufactured from fine manganese ores. However, the distribution of manganese ores is significantly uneven on earth, and their characteristics considerably vary by ore type. It is known from experience that the production of high-carbon ferromanganese by the electric furnace method depends greatly on material ores. Therefore, to maintain stable operation in the electric furnace-smelting field, it is important to identify the characteristics of each type of material ores in advance. Thus, we evaluated the high-temperature electric characteristics of manganese ores using the electrical conductivity measuring system developed by ourselves and provided the standards for determining ores and blending ratio necessary for stable operation of the electric furnace based on the evaluation results. This time we worked for optimisation of the high-temperature electric characteristics of sintered manganese ores through modification of the characteristics because the blending ratio of sintered manganese ores in the electric furnace is high. The electrical conductivity of sintered ores having various chemical components in a high-temperature region (up to 1 550°C) was measured using our electrical conductivity measuring system and high-temperature electric characteristics evaluating method reported at INFACON 9. As the result of the measurement, we revealed that the high-temperature electric characteristics of the sintered ores depend on their chemical contents and the sintered ores can be modified to those having excellent high-temperature electric characteristics by controlling their chemical contents, so that the resources can be effectively used.

Jan 1, 2004

Existing processes for the recovery of platinum group metals (PGM) from UG-2 ores place stringent requirements with regard to chromite content upon feed material to the plant. An alternative hydrometallurgical process for which this is not an issue is proposed that involves reductive roasting of the ore followed by leaching with HCl/chlorine, ion exchange, and recovery of PGM from the ion exchange eluate by reduction. Problems associated with leaching of PGM are discussed and results of laboratory testwork for each of the process steps are given.

Jan 1, 2004

A Seismic Hazard Scale (SHS) has been developed to provide a practical seismic hazard assessment tool applicable to mine site personnel. It has been applied to seismic data sets from numerous Western Australian mines. The SHS is applicable when quantifying seismic hazard on a mine wide scale, on a mining block scale, and on a local cluster-by-cluster scale. Spatial mapping of variations in seismic hazard is a particularly powerful application of the scale. The SHS is sensitive to temporal increases in seismic hazard. It has also been shown that the SHS can be applied to estimate seismic hazard when seismic monitoring data are not available. The SHS is a simple derivation of the Gutenberg-Richter relation. There are assumptions and limitations to the SHS that need to be considered when applying it to mine seismicity data.

Jan 1, 2004

By Steve Kral

Commodity price down cycles are a fact of life in the mining industry. And companies pre-pare for them as best they can. Evenso, operations are still curtailed or closed during those cycles, profits shrink, layoffs are inevitable and many companies do not survive. However, one of the few good things that occurs during down cycles is the new, innovative exploration, mining and processing technologies that come about during hard times. To survive the lean times, the mining industry turns to improved technology to decrease costs and hold the bottom line. And, because mining is a cyclical business, each down cycle brings about technology improvements that carry over into the good times.

Jan 1, 2004

By A. Ahmed, A. Fathy, M. Eissa, K. El-Fawakhry, A. El-Mohammady

Silicomanganese is widely used as a complex reducer and an alloying addition in the production of various grades of steel due to its economic and metallurgical advantages. It is also used as a semi-product in the manufacture of medium- and low-carbon ferromanganese and metallic manganese. Manganese-rich slag, resulting from high carbon ferromanganese production, has the advantages of high manganese content, high Mn/Fe ratio, low excess oxygen, low phosphorus content, low fine content and low cost. Such slag seems to be very attractive to use as raw materials for the production of silicomanganese alloys. In the present study, experimental heats were designed and carried out to optimise the factors affecting the production process of silicomanganese using manganese rich slag in the charge. The results of pilot plant experimental heats showed that the optimum metallic yield and recoveries of manganese and silicon are obtained with initial slag basicity,(CaO + MgO) / (Al2O3), equals 1.8 by using dolomite as fluxing material and charging quartzite and fluorspar in percentage of 25% and 4% of the blend, respectively. The results showed also that an amount of 30% of coke in excess of the stoichiometric amount should be added. These result are relative for the specific high Al2O3 ores used.

Jan 1, 2004

By Corry Goumans, Ron J. Elliot

This paper discusses the challenges encountered in drilling and blasting of a small diameter shaft underneath a parking garage in historic Gastown, Vancouver, BC. This project involved drilling in a restricted headroom area, blasting in a confined space environment, and excavating using a novel vacuum technique. The 1.2m x 1.2 m x 8.5m deep shaft was required for installation of a hydraulic piston for a show lift. The project called for very accurate drilling through inter-bedded sandstone and siltstone within the water table. Development of a unique blast design was required for blast vibration control on a historic structure located just 15.8 meters away. The shaft was successfully completed without damage to any of the surrounding structures.

Jan 1, 2004

The Indonesian province of Papua is a remote jungle-clad region covering the western half of the mountainous island of New Guinea. Despite being relatively under-explored to this day,Papua is home to the greatest mineral success story of the 20th century. The Grasberg/Ertsberg minerals district atop the central dividing range contains the worldÆs largest reserve of both copper and gold (Freeport-McMoRan Copper and Gold, 2002). With large mines at Ok Tedi,Por gera and Lihir,and many well-delineated resources such as Frieda River,Wafi and Hidden Valley, neighbouring Papua New Guinea,the eastern half of New Guinea has enjoyed sustained exploration campaigns for gold and copper since the mid 1960s. The combined Grasberg and PNG exploration successes can be measured in terms of ounces of gold produced over the last decade versus available landmass,conf irming the island of New Guinea and surrounding islands as a world-class destination for gold explorers. Yet despite this obvious regional prospectivity and the profitability of the Grasberg operation, a sustained exploration effort in the Papua province in Indonesia has not been achieved. Periodic political constraints, poor infrastructure, high costs, operational challenges, social and environmental concerns and lack of immediate exploration success often impact exploration investment decisions. Accordingly a lesser number of mineral occurrences have been documented in Papua compared to those seen along tectonic strike in geologically similar Papua New Guinea.

Jan 1, 2004

By D. Komljenovic, J. Paraszczak

"This paper presents the use of queuing theory in truck fleet sizing in open pit mining operations. In the first part, a methodology is developed by which an optimal ratio between the size of shovels and trucks may be determined. The second part gives the fundamentals of the queuing theory and its application in analyzing shovel and trucks. The stochastic character of involved times (loading, truck cycle, etc.) is taken into consideration. Using the above theory, the optimal truck fleet size in actual conditions may be estimated. Minimal operating cost of the working system (shovelstrucks) represents the basic requirement of the analyzed process. The methodology was validated on Caterpillar front-shovel – truck combinations. IntroductionLes camions représentent probablement les équipements les plus utilisés pour le transport dans les mines. Le coût de transport peut parfois atteindre 50 % du coût d’exploitation et 25 % du coût total (Collins, 1996; Kennedy, 1990). Il est critique pour une opération minière de le minimiser. C’est un sujet qui a été traité relativement souvent dans la littérature spécialisée. Les premières applications informatiques dans l’industrie minière ont été développées pour la détermination du temps de cycle des camions.Au fil des ans, la capacité des camions a augmenté et, aujourd’hui, les plus gros manufacturiers de camions (Caterpillar, Orenstein & Koppel, Euclid, Terex, Unit Rig, Komatsu, Liebherr, Belaz) fabriquent des camions ayant une capacité de 200 t et plus dont quelques-uns d’une capacité supérieure à 320 t. Pour les plus gros camions, le coût d’opération peut même dépasser 240 $US/heure dans des conditions modérées (Caterpillar, 1999). Les mines modernes de grande taille peuvent posséder plusieurs dizaines de camions dans leur flotte."

Jan 1, 2004

By Bruce Geller

The 2004 Prospectors and Developers Association of Canada (PDAC) conference contained an air of optimism and excitement that has not been seen since 1997. Many segments of the mining industry are alive and well. This is largely a reflection of improved metal prices, themselves due to the strong euro and improvements in Asian economies. Those factors offset higher oil prices, a weaker U.S. dollar and concerns about the Middle East. This report is an overview of the conference. It is supplemented by an examination of conference handouts, abstracts and a few complete papers that are on the PDAC’s Web site www.pdac.ca. Sixty PDAC 2004 abstracts are available at the same site, along with 15 complete papers in PDF format. The conference was held March 7-10 in Toronto, Ontario. It was attended by a record 9,200 delegates from 85 countries. About 8,000 people from 74 countries attended the 2003 conference.

Jan 1, 2004

By C. J. Martin, M. P. Hay

"A methodology was developed in the mid-1980’s to predict plant performance from standard laboratory flotation tests. The technique is based on a simple, empirical kinetics model, and is tailored for use by the practical metallurgist.To date the performance of more than 20 flotation plants has been predicted, including copper, lead, zinc, phosphate, pyrite, graphite, cassiterite, platinum, nickel and various slags. The method has successfully been used to predict and size four flotation plants directly from bench-scale laboratory flotation testwork. All have since been commissioned, and have performed as predicted.The technique has now received broad acceptance within the South African mining industry, for example in the last year alone it has been used to drive flowsheet development for at least seven new plants. It is also being used to assist in the optimisation of existing operating plants.The methodology is described in this paper and verification of the methodology is presented using case studies of porphyry, polymetallic and PGM operations.INTRODUCTIONThere is considerable interest these days in the use of modelling to simulate flotation circuits, for process design and plant optimisation purposes. Although these models are proving to be useful tools for plant design and optimisation, their complexity can make them cumbersome – expensive to use and difficult for metallurgists to visualise and mentally absorb, without a background in each specific technique. In “SUPASIM” no attempt is made to measure flotation fundamentals, rather to use empirical relationships between laboratory flotation kinetics and plant performance – relationships that hold up well to validation exercises as will be demonstrated later in this paper. Although not designed to be as comprehensive as other models, “SUPASIM” is easily understood by the operating metallurgist and can be quickly and easily applied."

Jan 1, 2004

By Jeffrey M. Taylor, Arturo Ressi di Cervia

"Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 foot (2.44m) diameter drilled shafts with 7.5 foot (2.31m) rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at both the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts. INTRODUCTIONThe replacement Brightman Street Bridge spans the Taunton River between Fall River and Somerset in Massachusetts.The new crossing is located approximately 1500 feet (450m) upstream from the existing Brightman Street Bridge, which was built in 1908. The new mainline bridge includes nine spans totaling 1725 feet (525m). A bascule type moveable span will be located in the middle of the Taunton River and provide a 200 foot (61m) open channel centered about the 400 foot (122m) navigational channel. The bascule span, which has a span length of 409 feet (124.7m), will be a trunnion-type four leaf structure with a solid deck. A site plan is shown in Figure 1 Contract 3, which includes construction of the foundations for the East and West bascule piers, was bid on December 19, 2000 and was awarded to Modern Continental Construction Company (MCC) on January 24, 2001. MCC in turn awarded the subcontract for the installation of the drilled shafts to TREVIICOS Corporation, which started mobilizing in June of 2001.The scope of work for the drilled shafts of Contract 3 consisted in installing 18 drilled shafts in three rows on each side of the river to support the bascule piers located in the middle of the Taunton River.The foundation plan for the bascule span is shown in Figure 2."

Jan 1, 2004

Ferrochrome is the major chromium source for stainless steel production, and submerged-arc furnaces (SAF) are most commonly utilised to smelt chromite ores into ferrochrome by using suitable carbonaceous reductants such as coke. Because of the complexity of feed structure and electrical-thermal-chemical interactions, there exist large gradients and wide distributions of temperature, mineralogy and other process variables in the furnace. This leads to various zones in the furnace, and different reduction mechanisms. Control of the furnace is thus often difficult due to the complicated physical and chemical situations in the furnace. The temperature profile in the submerged arc furnace has a great influence on the reduction rate and the production efficiency. Therefore, the energy generation through electrical arcs submerged in the solid feed and its distribution within the packed bed play an important role. In the present paper, an overall process model is illustrated to simulate inter-linked transport processes of fluid flow, heat transfer and reduction kinetics within the submerged arc furnace. The application of reaction kinetic data to simulate the chromite pellet/lumpy ore reduction with CO gas is presented and further adjusted to provide a submodel for a flow and heat transfer simulation for the packed bed by using computational fluid dynamics (CFD) technique. The comprehensive process model is aimed to simulate materials and gas flow, temperature and energy distribution throughout the furnace system. A preliminary model for gas flow and temperature distribution for the upper part of a 20 MW furnace (the packed bed) for high carbon ferrochrome production has been developed under simplified conditions. The integration of the reaction kinetic model into process simulation, and the future vision for a more comprehensive process modelling are discussed. It is expected that better understanding of the furnace insights through process modelling will help process optimisation and furnace control.

Jan 1, 2004

By A. R. Naji Meidani, A. Cameron, A. Richardson, M. Isac, R. I. L. Guthrie

The supersonic core of shrouded jets remain coherent over longer distances vs conventional supersonic jets. This phenomenon should allow for greater penetration of oxygen into slag/steel reactor systems. As such, they hold the promise for faster slag/metal mixing in BOF type metallurgical reactor systems, possibly creating greater surface area/volume ratios of reacting phases, and thereby faster kinetics, as compared to conventional supersonic jet systems. In order to assess the potential of shrouded supersonic jets versus their conventional counterparts, an experimental investigation of impinging shrouded supersonic jets into a water model of a simplified BOF system was carried out in the MMPC's water modelling laboratory. The experimental results for three different designs of a shrouded supersonic jet nozzle have been compared in terms of greater penetration depths and reduced mixing times. Based on a novel dimensional analysis, the depth of penetration of a gas jet into a liquid bath is shown to depend on the nozzle-bath distance, the liquid's Froude, Reynolds and Weber numbers, reflecting the ratios of gravity, viscous and surface tension forces to the jet's inertial, or momentum, forces. Good agreement between the mathematical model and experiment was obtained in terms of predicted and observed depths of penetration. Further efforts have been made to study jet penetration into liquid metals. The effects of mean liquid density of slag/metal mixtures and a wide range of gas flow rates on the penetration depth were investigated theoretically. The results show that the penetration depth can be increased with increasing gas flow rate and decreased bath density.

Jan 1, 2004

A model has been developed for drum scrubbing which allows selection of geometry and power input. Specific aspects considered are: Calculation of total static and operating volumes. Total residence time based on total operating volume. Solids residence time based on solids operating volume. Selection of the aspect ratio. Alteration of operating fill to allow for smaller or larger feed openings. Selection of proportion of critical speed. Calculation of shell and motor power requirements. The model uses either solids or total residence time to calculate the required operating volume. The solids residence time is based on the proportion of coarse solids in the feed. Material finer than the reject size is considered as part of the slurry. The solids operating volume is the static volume plus the surcharge on the discharge weir required for flow of the solids from the unit. The total operating volume is the static volume plus the surcharge on the discharge weir for the total flow to exit the scrubber. The burden density is calculated from the coarse solids bulk density and the slurry density that includes all the fine solids. Power is calculated using the Liddell and Moys correlations for burden position and shape, and the operating rotational speed. Results from the model (especially power) have been verified from industrial installations of significant size. Predicted and observed power draws are within two per cent. A check against the JKMRC mill model shows power draw prediction agreement to within four per cent.

Jan 1, 2004