Search Documents

By Mikko Ruonala, Pertti Lamberg, Olli Hyvärinen

The smelting of copper sulphide concentrate is the dominant route in copper production (Figure 1). Heap leaching of oxidized copper ores with weak sulphuric acid together with copper solvent extraction and electrowinning has gained popularity during recent decades, and it accounts for close to 20 % of primary copper production. Heap leaching offers advantages such as lower costs and consequently the construction of a production plant at a mine site is made possible. Limited resources of oxidized copper ores, the long leaching time of chalcopyrite and inability to recover gold inhibit this growth. The HydroCopperTM process developed by Outokumpu Technology at the laboratories of Outokumpu Research, Pori, Finland, is a new chloride leaching technology /1,2/, which offers an alternative to smelting and heap leaching (Figure 1). In the HydroCopperTM process sulphidic concentrates with various mineralogy and grade can be treated at the mine site to produce high-quality copper. Instead of copper cathodes the HydroCopperTM end products are copper wire rod, copper bars or copper billets. One of the advantages of HydroCopperTM technology is that gold can also be recovered in the process simultaneously /3/. To confirm the functioning of the new process and to dimension equipment Outokumpu Technology built the HydroCopperTM demonstration plant in Pori, Finland /4/. It has a capacity of 1 metric ton of copper per day. After testing with Pyhäsalmi copper concentrate in 2003, the first commercial demonstration run with Erdenet copper concentrate took place in 2004.

Jan 1, 2005

By Y Peng, D Wannas

In the fine particle flotation technologies being developed today the fine hydrophilic (gangue) particles are usually well dispersed. These highly dispersed fine particles can be recovered into the flotation froth product by mechanical entrainment. Flocculation of hydrophilic particles caused by polymer depressants could potentially reduce the mechanical entrainment of these particles. This paper reports testwork completed on fine particles of several solids, iron oxide, hydroxylapatite, galena and sphalerite, as well as on a relatively coarse quartz sample (-75+38 ¦m). Dodecylamine was used as a collector for the quartz, and several dispersants and polymer depressants, including sodium silicate, sodium metaphosphate, zinc sulfate, potassium dichromate, corn starch, corn dextrin and carboxymethyl celluloses (with molecular weights of both 700 000 and 80 000) were used as flotation modifiers. The major part of the testwork involved flotation tests in a 200 ml flotation column. Both water and solid recoveries were recorded. The degree of flocculation and dispersion was determined by settling tests in 250 ml graduated cylinders. It was observed that flocculation of the fine hydrophilic particles significantly reduced their mechanical entrainment, while dispersion severely aggravated it. Thus, in the flotation separation of artificial mixtures of the -75+38 ¦m quartz and fine iron oxide or hydroxylapatite, polymer depressants that caused flocculation were found to perform better than the ones that did not cause flocculation.

Jan 1, 2005

By T. Rasmussen, T. G. Jørgensen, T. Fischer, R. K. McLimans, C. Knudsen, D. Frei

Ilmenite-bearing paleo-beach deposits were discovered in Jylland, Denmark using a combination of Ground Penetrating Radar (GPR), portable X-ray fluorescence (XMET), bulk XRF analyses, Computer Controlled Scanning Electron Microscopy (CCSEM), and wire line logging. The Miocene-age paleo-beach deposits are located below a thin Quaternary cover in a region of very moderate relief and essentially no outcrop demanding unique approaches in exploration. Initially, an isopach map of the Quaternary is prepared from existing water well data. A geological model for likely occurrence of Miocene paleo-beach deposits is generated and the coincidence of thin Quaternary cover and potential paleo-beach deposits define targets for detailed exploration. The defined targets are traversed with GPR to identify paleo-beach structures which are then used to define a drilling program. This methodology located a paleo-barrier island at the Vorslunde location with more than 10% ilmenite in the sand. During the drilling process, the TiO2 and heavy mineral contents of the sand were logged every meter with a portable XRF unit (XMET) and subsequently calibrated more accurately by comparison to bulk XRF and CCSEM analyses for selected samples. The bulk XRF data also provided more complete compositional information. Insitu determination of geology, heavy mineral abundance, and corroboration of the XRF logging was done using wire line logs, a combination of spectral gamma and induction conductivity logs. Detailed characteristics (abundance, grain size, shape) and chemical composition of minerals was determined by the GEUS CCSEM methodology (Frei et al, this vol.). The average weight percent TiO2 for all Ti-minerals is 62%, 60% excluding rutile. That elevated TiO2 content (>> ilmenite stoichiometric value, ca. 50 %) indicates that ilmenite experienced an iron-leaching environment. The source of the sand deposit was investigated by dating contained zircon. The results show that the likely sources of zircon are in southern Norway and southwestern Sweden with common zircon ages of ca 1100 Ma. and 1500 Ma.

Jan 1, 2005

By Emre Biringen

"Results from a small-scale laboratory experimental program show the changes in the vertical stiffness and strength of a soft clayey soil adjacent to the shaft of an inserted pile (i.e. expansion of a cylindrical cavity). The experimental program provides a realistic axi-symmetric physical model of an element of a cylindrical pile and the surrounding soil. The study interprets the improvement and assesses its magnitude in vertical stress-strain-strength properties of a normally consolidated soft cohesive soil in response to preloading impact in the radial direction. The results verify that insertion of a cylindrical pile causes densification of surrounding soil in a radial direction due to change in stress state around the pile, and thus consolidating and stiffening of the soil.The test results indicate that most improvement in modulus and strength takes place within a distance of 4 times the radius of a pile, though significant improvement is realized to a distance of 8-10 times the radius, beyond where there is negligible effect. Settlement characteristics of the surrounding soil in a zone of 12 times the pile radius improve significantly after the formation of a cylindrical cavity. The miniature vane shear strength tests show a 1.5 times increase in a zone of 4 times the pile radius compared to the strength at 10 pile radii. The results also imply that the spacing of cylindrical piles should not be more than 4 to 10 times pile radius, so that the surrounding soil matrix may improve the vertical bearing capacity under any foundation or embankment loading.INTRODUCTIONThe engineering community is familiar with different techniques to improve the bearing capacity and settlement characteristics of weak cohesive and organic soils. Some of the in situ techniques to improve the properties of soft ground (e.g. soft clays) prior to placement of foundations are vertical preloading, deep cemenUlime mixing, stone columns, and grouting (Henn 1996; Moseley 1993). In addition to these methods, researchers have recently showed interest in achieving soft ground improvement by means of applying radial compression method for which different names exist including expanding pile (Kelleher et al. 2001 ), Preload™ Pier (Biringen and Edil 2003), and sand compaction pile (Lee et al. 2004). Handy (2001) has described how preloading can also be achieved by imposition of radial loading in soft ground with an expected improvement in stiffness. The idea behind the latter method is densification and consolidation of soft soil in the radial direction by controlled displacement for which the process can be viewed as a cavity expansion problem (Vesic 1972)."

Jan 1, 2005

By Monica Prezzi

"Auger cast-in-place (ACIP} piles and drilled displacement piles are being increasingly used as foundation elements for structures, particularly in projects requiring accelerated construction or involving the rehabilitation of foundations of existing, overstressed structures. Auger cast-in-place piles (also referred to as continuous-flight-auger piles) are widely used to construct the foundations of all types of structures. There are many different types of drilled displacement piles, with the installation methods varying according to the equipment used. Depending on the specific rotary piling technology used, responses ranging from those associated with non-displacement to those associated with full-displacement piles are obtained. Conventional pile design methods do not account for how the various construction techniques involved in auger piling change the soil state around the pile during installation and, hence, cannot accurately estimate the pile resistance in a consistent way. Research on this subject, identifying the different variables that must be accounted for in design and linking these variables to installation methods, is lacking. This paper describes the different piling methods available for auger cast-in-place and drilled displacement piles, the equipment used to install them and the quality control processes typically used. It also reviews some of the design methods currently used.IntroductionDeep foundations are extensively used in geotechnical engineering practice. The wide spectrum of piling methods results in a variety of pile types. Each type behaves differently, depending on the installation or construction methods. On one end of the spectrum are non-displacement piles, the classicql examples of which are bored piles or drilled · shafts. These piles are constructed by removing a cylinder of soil from the ground and replacing it with concrete and reinforcement. On the other end are full-displacement piles, such as closed-ended pipe piles or precast reinforced concrete piles, which are typically driven into the ground. Driven piles preload the materials below the toe of the pile and displace the soil surrounding the pile shaft laterally during the installation process. Therefore, displacement piles are, in general, more likely to have a stiffer response than non-displacement piles. This is true particularly in the case of sandy soils where displacement causes densification."

Jan 1, 2005

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been studied on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27° between each tuyere, and five side tuyeres with an angular separation of 22.5° or 27° between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By Bob King

Jan 1, 2005

By A. Nivala, S. Ulgiati, M. Canino

Mining and processing of bastnaesite ore, (Ln)CO3F, for lanthanides extraction is investigated in this paper. This series of elements proved to be applicable for a wide range of high-tech uses. In spite of the strategic importance of lanthanides, no LCA and energy analyses of their extraction have ever been published. We perform in this paper a Life Cycle Assessment of the Lanthanide production cycle, based on available database and literature data from Mountain Pass mine (USA) and other worldwide mining and processing sites, most of which in China. We investigated three main steps: mining, milling (including transport, grinding and drying), and flotation (for lanthanide chloride extraction). We do not investigate here the separation of pure oxides from lanthanide chloride, a compound which is also marketed as such. The conventional LCA was integrated by means of energy and emergy evaluations, aimed at investigating respectively the global energy cost and the environmental sustainability of the process. Indicators of material intensity, thermodynamic efficiency, and environmental impact (including LCA and ecological footprint impact categories) are calculated and discussed.

Jan 1, 2005

By P. M. Soupios

A near geophysical surface investigation of a landfill area close to the Hania city, in Crete Island, Greece, was conducted as inextricable phase of a preliminary geotechnical, geological and hydrogeological study of the area under investigation. Electrical Resistivity Tomography (ERT), one of the most promising prospecting techniques mainly concerning its effective contribution to resolve several environmental problems, was applied for the geophysical modelling. ERT is a robust imaging method the theory and implementation of which are well documented in geophysical research literature. The survey site is located in Akrotirion Peninsula, about 7km east of Hania city in Crete I. The geological setting comprises Trypalion limestones, marly limestones and a clayed weathered layer. Cavities are also identified at various scales which are recent tectono-karstic voids resulted from the combined actions of karstic erosion and tectonic stress on the Trypalion limestones where they are located. Due to the above-mentioned geological singularity and in the light of the requirement for an environmentally safe construction of the landfill, an ERT survey was carried out by deploying the dipole?dipole electrode configuration. Specifically, seven geoelectrical tomographies were conducted reaching the prospecting depth of 36m. The resulted images conduced, a) to overcome geotechnical problems, b) to plan the future sites for waste disposal and c) to reliably estimate the thickness of the already deposited wastes.

Jan 1, 2005

By P. -Q. Wu

A modified electrochemical noise (EN) technique has been applied to monitor corrosion wear of TiN-coated ASP23 steel and TiN-coated AISI 316 stainless steel sliding against corundum in 0.5 M H2SO4. Experimental results show that the EN technique can sensitively detect potential and current variations during a corrosion-wear process. Corrosion-wear mechanisms of TiN coatings depend on their substrate properties. If the substrate is passive, such as AISI 316 stainless steel, the potential and current variations reflect the properties of the coating. Depassivation and repassivation alternately take place on the tribo-activated wear area during the steady-state phase. If the substrate is active, such as ASP23 tool steel, the electrochemical noise is dominated by dissolution of the substrate at the pinholes and the hydrogen evolution all over the exposed surface.

Jan 1, 2005

By Peter Shuttleworth, Chris Fesq, Eddie Woods

Precast concrete segmental linings for tunnels have traditionally been designed with conventional steel bar reinforcement. In many cases, this has been satisfactory in service, but in others, major problems have occurred with the durability of the linings. Commonly this has resulted from corrosion of the reinforcement, mainly from chloridesin ground water, causing spalling of the concrete and leading to very expensive and disruptive repair programs. This paper discusses the relative merits of designing tunnel linings with steel fiber reinforcement to provide long-term durability, improved impact resistance and toughness for greater load capacity across joints, enhanced robustness during transportation and erection, plus improved fire resistance with the addition of polypropylene fibers. Guidance is also given in the selection of the correct fiber type, mix design and testing methods to establish the optimum dosage required and production techniques to ensure even distribution and compaction.

Jan 1, 2005

By William W. Edgerton, Calvin Locke

INTRODUCTION King County, Washington operates a regions wastewater treatment system that provides treatment to 18 cities and 16 sewer districts in the greater Seattle metropolitan area. The system serves 1.4 million people and currently includes two regional treatment plants. In 1999, a long-range planning study identified the need for a third regional treatment plant, now known as Brightwater. Prior to this project, the county has almost exclusively used the traditional design-bid-build delivery process for its capital projects. However, with the adoption of the RWSP, the county began to study the potential application of innovative project delivery methods. This paper looks at the project delivery methods used for the Brightwater project, based on the specific needs of this large, complex, and multi-faceted project. THE KING COUNTY WASTEWATER TREATMENT SYSTEM In 1958, voters approved the formation of a regional agency called the Municipality of Metropolitan Seattle, or Metro, to build and operate a regional wastewater collection and treatment system. Prior to the formation of Metro, there were no regional wastewater treatment facilities and pollution of Lake Washington and Puget Sound from untreated sewage was a concern for many residents. In 1994, King County merged with Metro. The county’s 1,087 square kilometer (420 square miles) wastewater service area covers most of urban King County and extends into portions of two neighboring counties. The system includes two regional treatment plants, a local plant, 61 pump and regulator stations, and 571 kilometers (355 miles) of conveyance pipeline which convey wastewater from local districts to the treatment plants. As with other areas, the greater Seattle/King County region has seen rapid population growth. The RWSP estimates that the current system would soon reach capacity, and called for the construction of a new third regional treatment plant, called Brightwater, to be operational by 2010.

Jan 1, 2005

By Vijenac Quarry, A. Iljazagic, t. Knezicek, T. Omeragic

Limestone quarry Vijenac, is one of the key limestone producers in B&H. Conventional massive drilling and blasting is the technique applied for limestone exploitation. Utilized blasting scheme causes appearance of large oversize stone pieces, uncontrolled flying stone and undesirable seismic effects. In order to reduce or eliminate exposed disadvantages and to improve environment in the area of Vijenac quarry, an innovative blasting scheme was tested. Conventional blasting scheme was changed from single row, deep inclined blast holes combined with two lines short horizontal holes to multi row, inclined blast holes combined with a single line short horizontal blastholes. Applied innovative blasting scheme reduces negative blasting impact on the environment through safer working conditions, reduced amount of dust after blasting, reduced explosive and energy consumption, reduced appearance of explosive gasses and reduced earth and air vibrations as the result of seismic effects.

Jan 1, 2005

Proper water and thermal management is essential for obtaining high performance of Proton Exchange Membrane Fuel Cells (PEMFCs). A steady, two-dimensional water and thermal management model was developed, aiming at considering pressure drop, open circuit voltage variation with stack temperature, water vapor effects on membrane conductivity, which made the model physically more reasonable and more suitable for various operating conditions. The model could predict the distributions of a series of important parameters along the flow channel, and thus the effects of various operating and design parameters on the fuel cell performance could be investigated easily by numerical trial-and-error method. The modeling results compared well with the available experimental results from the literatures. The results also showed that the humidification is crucial for the performance of PEMFCs. The model could be a very useful engineering tool for the optimization of PEMFCs.

Jan 1, 2005

By F. L. Pirkle, D. L. Pirkle, E. C. Pirkle, W. A. Pirkle

Heavy minerals have been mined from the sands of the United States’ Atlantic Coastal Plain since the early part of the twentieth century. Production of ilmenite from beach sands near Mineral City (Ponte Vedra), Florida, began in 1916. The first reported large-scale recovery of zircon in Florida was reported from this deposit in 1922 and of rutile in 1925. These operations ceased in 1929. Today the Ponte Vedra Country Club and Golf Course is situated in the center of the former mining site. In 1942 heavy-mineral operations were established on 202 hectares of land situated in Duval County, Florida. The location is about 16 kilometers east of the center of Jacksonville, Florida, in an area known as Arlington. This operation demonstrated that low-grade sand containing only 2 to 3 percent titanium minerals could be concentrated economically with the Humphreys spiral and that the oxides could be separated from the heavy silicates by electrostatic methods. Much of this area is now covered by a large mall and is a major retail- commercial center. Between 1958 and 1964 the Skinner tract, a deposit about 4 kilometers south of the above deposit, was mined. Today the area of this deposit is known as Deerwood, a gated country club community on the southside of Jacksonville. Further inland, E.I. du Pont de Nemours and Co. has been mining heavy minerals from a physiographic feature known as Trail Ridge since 1948, and a deposit near Green Cove Springs, Florida has been in production since 1972. Since the start of heavy-mineral mining in the southeastern United States, nine heavy-mineral ore bodies either have been or are being exploited in Florida and Georgia. Other deposits either have been lost to mining or are yet to be mined. These deposits have different origins. Some formed along shorelines at the heights of marine transgressions while others formed on regressional beach ridge plains during periods of temporary stillstands or slight transgressions. These different origins are reflected in the chemical and physical characteristics of the deposits. Ilmenite in older, more western deposits has a higher TiO2 content than ilmenite in younger, more eastern deposits. TiO2 content does not very with north-south direction. Garnet and epidote are absent or rare in the older Trail Ridge deposits, but progressively become common in the younger Duval Upland, Crestal Pamlico, and Holocene deposits. Grain size is coarsest for Trail Ridge sediments and finest for sediments in Duval Upland and Crestal Pamlico deposits. The average grain size for Holocene deposits is intermediate between Trail Ridge and Duval Upland deposits. The two models for the origin of the heavy-mineral deposits – deposits formed at the height of major marine transgression; and deposits formed during periods of temporary stillstands or slight transgressions that occur during a general marine regression; - are consistent with known sedimentological data and depositional trends.

Jan 1, 2005

By J S. Laskowski

Froth flotation process requires the use of frothers. These important flotation agents are commonly characterised as either æselectiveÆ or æpowerfulÆ and are chosen following general guidelines and verification by laboratory and/or pilot plant tests. Fundamental properties of the flotation frothers have been extensively studied over the last few years. These studies have led to the development of standardised procedures to characterise frothers in terms of their ability to reduce bubble size and to increase foam stability. In this research project, the performance of five frothers in flotation of coal is evaluated and related to the fundamental properties of these agents. Since the recovery of water in the concentrate is closely related to the non-selective transport of solid particles by entrainment, the tested frothers are also assessed in terms of their ability to promote the transport of water towards the froth collection zone, both in absence and in presence of solids.

Jan 1, 2005

By R L. Brathwaite

The epithermal gold-silver deposits wall poster is one in a series of posters on different mineral deposit types being produced by GNS Science to raise awareness of the characteristics of New Zealand mineral deposits and their prospectivity. Epithermal deposits consist of quartz veins, quartz vein stockworks and hydrothermal breccias that are mainly hosted in subaerial andesitic or rhyolitic rocks of Tertiary age. The deposits were formed at depths of typically less than 1 km and at temperatures between 180¦ and 320¦C, although ore grade mineralisation was generally deposited at less than 270¦C.   In New Zealand, epithermal deposits occur in association with late Cenozoic volcanic rocks in the Northland, Coromandel and Taupo volcanic regions. All of the past and present gold production, estimated at greater than 380 t (along with 1300 t Ag) comes from the Miocene-Pliocene Coromandel Volcanic Zone, where about 50 epithermal gold-silver deposits occur over a 200 km long belt. In Northland, silver and mercury have been produced from hot spring type epithermal deposits, and several gold-silver prospects have been identified. Ore grade gold-silver mineralisation is currently being deposited in several active geothermal fields of the Taupo Volcanic Zone, and extinct geothermal systems occur on the western side of the zone. The active systems have provided natural laboratories to help understand the processes of epithermal mineralisation.

Jan 1, 2005

By K. Freytag

The extraction of lignite in open-cast mines has a severe impact on the landscape. Proper landscaping after the shut-down of the mines has always been the statutory responsibility of the mine operator. The large area of the land used for open-cast lignite mining requires special regional planning procedures well in advance of the permitting procedure stipulated in the mining law. The lignite plan determines, among other things, the objectives of land reclamation. These objectives will then be outlined in more detail in the mine operation plans and implemented accordingly. Apart from the actual mining laws and regulations, a large number of environmental laws also determine the process of land reclamation. The success achieved in the field of land reclamation in all mining regions during the recent decades has shown that the lignite mining industry creates new landscapes that do not leave any scars in the countryside and merge very well with it.

Jan 1, 2005

By S. Schwartz, T. Bilney

"Over recent years a number of techniques have been developed as part of the AMIRA1 P9 project to represent mathematically or measure directly sub-processes occurring in flotation cells. These include the determination of:•,?a machine parameter (bubble surface area flux, Sb);•,?a froth parameter (froth recovery, Rf );•,?entrainment and drainage parameters (???and d); and•,?an ore floatability parameter (Pi).These flotation parameters allow the plant engineer to develop a model of the flotation circuit that can be used as a powerful tool to diagnose the performance of that circuit. The recently developed JKSimFloat V6 flotation simulator uses these parameters to predict the flotation circuit performance that would arise from changes in operating conditions and circuit configuration.This new flotation technology was applied to the Placer Kanowna Belle Gold Mine in Western Australia. A series of plant surveys, cell characterisation measurements and laboratory batch tests were conducted to determine the flotation circuit model parameters to be used within the JKSimFloat V6 simulatorA thorough flotation circuit analysis was then performed at Kanowna Belle using JKSimFloat V6. The recommendations that were provided by this circuit analysis have resulted in large improvements in the flotation performance at Kanowna Belle. These include a 1.3% increase in flotation gold recovery and a substantial decrease in operating costs. The analysis is still ongoing, however, the benefits already obtained from applying this technology have resulted in a US$1.3 million a year improvement to the mine."

Jan 1, 2005

By Y. Nien Wang, Moe Amini, Heiner Sander, Max John

INTRODUCTION As the population increased along the coast route (California Route 1), and the people’s need to have guaranteed access increased, the landslides and related road closures began to have serious adverse economic impacts. Landslides were causing major long-term road closures about every 10 years on average. In 1983, ground movement at Devil’s Slide caused Highway 1 to be closed for an extended period of time which caused significant economic loss to the surrounding coastal communities. A number of options for bypassing the slide area were considered, and the Martini Creek inland bypass was selected for design. Subsequent litigation led to the creation of the Devil’s Slide Tunnel Study in 1996. The results of this study indicated that a tunnel alternative would be competitive with the inland bypass. The final decision was left to the citizens of San Mateo County, who approved the tunnel alternative in the November, 1996 election After completion of environmental studies and the processing of legal challenges, the final environmental document was finished in 2001. The preferred tunnel alternative was designated to proceed for final design and construction. PROJECT DESCRIPTION The Devil’s Slide Tunnels consists of a separated two-lane road, one lane in each direction, which passes through twin tunnels and over twin bridges and then connects with the existing non-separated, two-lane road at each end. The total length of the project is approximately 1900 meters consisting of four main project divisions, which are described below, going from south to north. 1.Operations and Maintenance Center (OMC) area, 2.Southern approach roadways to the South Portals (250 meters), including the South Rock Cut,

Jan 1, 2005