Search Documents

By LUIS EAIYLNN SALAS

IF the ordinary wet method be attempted for silver-bullion containing tin, much trouble is experienced, varying with the amount of tin present. Even with a percentage as low as 0.05, the end-point is masked by a persistent turbidity, while with amounts ranging from 0.5 per cent. upward, the determination of the exact end-point is impossible, owing to the finely divided or colloidal metastannic acid resisting all efforts to cause it to settle, or to give a clear supernatant liquid. The object of the following experiments was to seek a remedy for these difficulties, and to find the conditions whereby the Gay Lussac method might be applied directly to these bullions. Material containing tin is met with frequently in bullion from Mexico or Bolivia; and tin is carried (sometimes in large quantities) in jewelers' sweeps. 1. A bullion was prepared containing Ag, 74; Cu, 25; and Sn, 1 per cent. A weighed amount was treated by the humid assay-method as if it were an ordinary bullion free from tin. Ten cc. of HNO3 (1.21) was added, and the bottle was heated until all traces of red fumes had been expelled. Before heating, the solutions were moderately turbid; and after heating, the turbidity greatly increased. One hundred cc. of normal NaCl solution was added and the bottle was shaken vigorously at intervals during 30 min. The turbidity persisted. The bottle was allowed to stand over

Mar 1, 1912

By T. P. Lim, N. K. Davé

"A modified accumulator method was devised to measure surface radon flux from porous media. It consists of a collector hood type of accumulator with a homogenizer pump and a pressure balancer. The latter was used to compensate any pressure changes produced during sample withdrawal and hence eliminate additional radon transport from the media. Errors resulting from radon back diffusion due to decreasing concentration gradient with time across the interface were also eliminated by measuring radon concentrations in the accumulator for two different periods of time and calculating the true radon flux, J(o), from the solution of a time-dependent radon transport equation in the absence of any pressure and temperature gradients.Core samples from the observation site were also withdrawn for laboratory determination of porosity, moisture content, bulk and grain densities, Ra-226 source concentration and the fraction of Rn-222 produced in the void volume. The data were used to calculate the radon diffusion coefficient for the media.Using the present method, the true value of surface radon flux for an abandoned uranium tailings pile was obtained as J(o) = 2020.2 mBq/m2/sec (54.6 pCi/m2/sec) compared to the value J = 1406.0 mBq/m2/sec (38.0 pCi/m2/sec) obtained by the conventional method. The bulk diffusion coefficient of radon for the media was obtained as 1.2 x 10-7 m2/sec.IntroductionRadon-222 (hereafter called radon) released from uranium mill tailings is a continuous source of environment radioactivity in terms of its transport as an airborne gas and its decay products. The particulate daughter products readily attach to aerosols or dust particles and can further be transported by various other environmental pathways. Typical radon release rates from existing tailings piles vary between 740 and 14,800 mBq/m2/sec (20-400 pCilm2/sec), depending on the nature of the tailings material, moisture content, etc. The United States Nuclear Regulatory Commission (NRC) is proposing radon release rates of 74 mBq/m2/sec (2 pCi/m2/sec) above that of background."

Jan 1, 1982

By Q. Han

A modified cast-on method has been developed to reinforce aluminum castings with steel insert. Defect-free bond between the steel insert and the aluminum casting has been consistently obtained. Data obtained from a push-out experiment indicated that the bond strength was much higher than that obtained using the Al-Fin approach. This paper introduces this modified method in four sections: the coating of the steel pins, the cast-in method, microstructure characterization, and the bond strength. The section on the coating of the steel pins contains coating material selection, electro-plating technique for plating Cu and Ni on steel, and diffusion bonding of the coatings to the steel. The section on cast-in method deals with factors that affecting the quality of the metallurgical bond between the coated steel and the aluminum castings. The results of microstructure characteristics of the bonding are presented in the microstructure characterization section. A push-out experiment and the results obtained using this method is described in the section of bond strength/mechanical property.

Jan 1, 2015

Small scale' table concentration tests have many critics. Many metallurgists consider that such tests are of problematical value because of the difficulties involved in conducting and interpreting them.Many kinds of small-scale ore dressing tests are difficult to conduct, and there is, perhaps, good reason for thinking that table concentration tests are amongst the most difficuIt.Interpretation of results from small-scale tests is the responsibility of the metallurgists and engineers in charge, and it is often held that small-scale table concentration tests are particularly difficmlt to interpret.TESTING FOR TABLE CONCENTRATIONOn analysis it appears that the difficulties encountered in conducting small-scale table concentration tests are of three fairly distinct kinds. Firstly, there are difficulties due inherently to the smallscale nature of the operations; for example the smaller width of all mineral bands on the table and the less complete separation due to the shorter length of travel between the feed and discharge points.Secondly, there are the effects of batch operation owing to the fact that the mineral particles behave differently during the initial period when the sample is just beginning to spread over the table, the middle period when feed and discharge are even and continuous, and the final stage, when the last of the sample has been added and the table is beginning to empty itself.

Jan 1, 1954

By Z. Leng

"After detonation of the explosive, the final blast-induced damage area around the blast-hole falls into three categories, namely crushed zone, fractured zone, and elastic deformation zone. This paper presents a modified model to calculate the size of crushed zone around a blast-hole in drill-and-blast, with the hoop compressive stress and cavity expansion effect taken into account. The material in the crushed zone was assumed to be a granular medium without cohesion, but with internal friction. On this basis, the formula for crushing zone radius was derived. The proposed approach was verified with tests reported in the literature and the simulated results from SPH-FEM coupled models. A full statistical analysis was also carried out, and the predicted values were found to be in better agreement with the test results compared with other models. A sensitivity analysis of the modified model showed that the size of the blast-induced damage area is mainly affected by the following factors: rock mass properties, in situ stress, and borehole pressure. In particular, the roles of borehole pressure and in situ stress are discussed. Finally, suggestions are made on how the size of the crushing zones can be decreased. IntroductionOver the past decades, drill-and-blast has become the most commonly used technology in rock excavation. It is well known that in rock mass fragmentation with explosives, the annular rocks around the blast-hole are converted into fines. The formation of these fines consumes a significant part of the energy of the detonation, which in general is ignored in the determination of the efficiency of detonation (Glatolenkov and Ivanov, 1992; Furtney et al., 2012). Many studies show that only 20–30% of the total explosive energy is effectively used in fragmenting the rock, and up to 50% of the energy generated by conventional charges is wasted in overcrushing of the crushed zone and the inner part of the fractured zone (Ouchterlony et al., 2004; Sanchidrian et al., 2007). How to control the crushed zone to enhance the effective utilization of explosive energy, reducing the unit explosive consumption and the engineering cost, is therefore of great significance."

Jan 1, 2016

By M. K. Mohanty

A modified coal flotation characterization procedure, referred to as the Advanced Flotation Washability (AFW) technique, has been developed which, compared to traditional procedures, provides a more accurate prediction of the optimum separation performance achievable by a froth flotation process. The AFW procedure uses a vertically-baffled flotation column which provides enhanced selectivity among particles of varying degrees of hydrophobicity due to a plug-flow environment and an improved carrying-capacity environment. In fact, the separation performance of the traditional procedures was enhanced by increasing the possibility of operating under improved selectivity conditions. The separation performance provided by the AFW procedure was superior to that obtained from multiple cleaning stages using commercially-available flotation columns under both kinetic and carrying-capacity limiting conditions.

Jan 1, 1997

By Z Fu, E Topal, O Erten

"Mine waste rock management involving waste rock movement and placement, is a critical aspect in the planning of open pit mining operations, as the waste rock haulage cost can be the largest portion of the mine operating cost. The concept of sustainable development in the mining industry also encourages environmentally friendly waste dumps that have zero hazards to people and the surrounding environment. Therefore, a detailed waste management schedule must satisfy economic and environmental considerations. However, the available tools in the market cannot provide optimal waste dumping schedules to meet all these constraints. This paper introduces a user-friendly and automatic tool to optimise the waste dumping schedule, which minimises the haulage cost, and covers the encapsulation of reactive materials to minimise acid mine drainage problems. This tool has been developed by using a new mixed integer programming (MIP) mathematical model that considers both single-lift and multilift dumping scenarios. The application of the proposed tool on a data set collected from a gold mine shows that the multilift dumping scenario has provided a more flexible and economical waste dumping schedule than the single-lift scenario, and both scenarios satisfy environmental requirements.Citation:Fu, Z, Topal, E and Erten, O, 2016. A Modified Software Tool for Mine Waste Rock Dump Planning, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 229–242 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

THE slide-rule, as a quick and convenient instrument for performing approximate calculations, is steadily growing more and more into favour with the engineer, and results obtained by it are considered close enough to enable him to satisfactorily dealwith a considerable portion of his work. To the surveyor, however, whose ordinary computations must be as precise as his measurements, the present makes of rule are insufficient, except for a very narrow margin of the scales and for rough work. Few will carry the rule when they can clearly see that it is unreliable for general routine, and the careful surveyor is inclined to look askance at those who do use it, recognizing the temptation there undtmbtedly must be to push it into work that the log book should be called upon to treat. From the fact that a surveyor's duties take him on the surface in all weathers, and underground in many wet and uncomfortable places, where the manipulation of a book of mathematical tables becomes both awkward and patience-trying, an efficient slide-rule must offer the mbst transparent advantages. Again, a surveyor being specially trained to read divided scales quickly and accurately, the slide-rule must commend itself as an apt addition to his outfit.

Jan 1, 1912

By David A. Newman

The Geomechanics Classification (Bieniawski, 1979) was modified for entry and roof support design in underground room-and-pillar coal mines. Adjustment multipliers were introduced to incorporate the influence of strata weatherability, high horizontal stresses, and the roof support reinforcement factor into the existing classification system. Sixty-two case histories of both standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant impact upon the supported stand-up time of coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1985

By A. Tosun

"The size distribution of the muckpile formed as a result of open pit blasting operations has a considerable effect on the efficiency of loading, hauling, and crushing. Various researchers have developed specialized computer software that uses image analysis methods for determining the size distribution of the muckpile. However, these methods have some limitations. One of the most important of these limitations is that the very fine fragments in the muckpile cannot be used in the size distribution calculation. In this study, 18 test blasts in total were carried out in two limestone quarries belonging to Batiçim Corp. in Izmir, Turkey. A new model was developed in order to ensure that very fine fragments are used in the size distribution calculation. The size distributions of the test blasts were calculated by both the Wipfrag computer program and the new model. Correlations were established between the muckpile size distributions determined by both methods and the parameters determining the efficiency of the loader. IntroductionThe size distribution of the muckpile formed as a result of open pit blasting operations has a considerable effect on the efficiency of loading, hauling, and crushing. Various researchers have established certain correlations for predicting the efficiency of the operations according to the muckpile size distribution so that production can be carried out economically (Tunstall and Bearman, 1997; Nielsen and Kristiansen, 1996; Workman and Eloranta, 2004; Michaud and Blanchet, 1996; Frimpong, Kabongo, and Davies, 1996; Osanloo and Hekmat, 2005; Molotilov et al., 2010). In these studies, the 50% passing size (X50) is generally used. These methods rely on the correct measurement of the size distribution of the muckpile formed by the blast. The most reliable measurement method would be to subject the entire muckpile to a sieve analysis, but this is obviously impracticable. Therefore, computational method based on image analysis have been developed. These include IPACS (Dahlhielm, 1996), Tucips (Havermann and Vogt, 1996), Fragscan (Schleifer and Tessier, 1996), Cias (Downs and Kettunen, 1996), GoldSize (Kleine annd Cameron, 1996), Wipfrag (Maerz, Palangio, and Franklin, 1996), Split Desktop (Kemeny, 1994), PowerSieve (Chung and Noy, 1996), and Fragalyst (Raina et al., 2002). In these methods, the size limits of the fragments forming the material are determined by image analysis on photographs of the muckpile. However, the computer software has some limitations. It does not take into account the third dimension of the muckpile, nor the size distribution of very fine fragments. In particular, the fragment size ranges below 2.5 to 3 cm cannot be determined, and therefore these cannot be included in the muckpile size distribution. However, the muckpile formed by a bench blast contains a wide range of particle sizes (Tosun et al., 2015)."

Oct 1, 2018

By Pradip, Beena Rai

A molecular modeling study was carried out on an adsorbed oleate monolayer on the surfaces of three calcium minerals, fluorite, calcite and fluorapatite using Universal Force Field (UFF) potentials. The cleavage plane of calcite {104} was the best template for oleate monolayer adsorbed since the surface structure enabled all the calcium sites available on the surface to be occupied by oleate anions. The area occupied per chain of oleate in this well packed monolayer was computed to be 20.2 Å, which exactly matches the value calculated to be the parking area per oleate molecule for a fully packed monolayer based on strictly geometric calculations. On the other hand, the precentage of calcium sites occupied by oleate to achieve a fully packed monolayer in case of fluroite and and fluorapatite was found to be 67% and 75% respectively. The results of this theoretical study suggest that while all the three adsorption conformations, that is unidentate, bidentate and bridging type are equally likely on fluorite and fluorapatite, bridging is most likely on calcite. Interestingly, all the conformations are observed experimentally for calcite-oleate system also. The reasons for this discrepancy between the theoretical predictions and experimental observations are not clear. More work is required to resolve this discrepancy, in particular simulation studies in presence of solvent water molecules on the surface.

Jan 1, 2003

By P. S. Bagga, P. T. Luckie

Liberation (the process of destroying the interlock between unwanted materials, such as mineral matter and pyrite, and coal) is one of the most important precursors to the benefication of raw coal in order to produce high grade marketable coals at economical recovery levels. Liberation is achieved usually by comminuting the raw coal. However, because of the significant interaction between the production of fine particles to achieve liberation and the cost of separating fine particles, the coal industry needs a method projecting the change in washability with size reduction. Such a projection can be combined with size reduction and separation simulators in order to examine completely beneficiation circuitry to produce coals of stringent specification. This paper presents the development of an appropriate liberation model for coal and its solution by Monte Carlo simulation to predict the expected washability of the raw coal as a function of comminution. It includes model validation with a known binary mixture as well as with a known teritary mixture.

Jan 1, 1983

By A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate, while increasing it decreased the corrosion rate. Keywords: austenitic stainless steel, % ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentio-dynamic scans, microstructure, chemical analysis.

Jan 1, 2007

By M. J. Papo, A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2 wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5 wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate while increasing it decreased the corrosion rate. KEYWORDS Austenitic stainless steel, %ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentiodynamic scans, microstructure, chemical analysis.

Jan 1, 2006

By N Weerasekara, M Bird, M Yahyaei, M M. Hilden, M S. Powell, J Franke, P Toor

The combination of new tools with a more rigorous approach to understanding the interaction of mill liners with overall mill performance and economics, forms the basis of an integrated approach to liner management. Based on accurate liner wear measurements, some (limited) physical mill inspections and surveys, accurate calibration of the mill load and analysis of process data, a whole new approach to liner selection, relining intervals and mill control is proposed. Collection and analysis of this information in operating mills illustrates the mill performance improvement which can be attained through this careful measurement and modelling approach.A more holistic approach to liner management is proposed, including a broadening of the current work to cover the potential benefits of improved relining technologies and predictive liner wear modelling. CITATION:Powell, M S, Hilden, M M, Weerasekara, N, Yahyaei, M, Toor, P, Franke, J and Bird, M, 2012. A more holistic view of mill liner management, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 95-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By P. Wells, P. Quinn

"A moveable flotation miniplant was designed and constructed at the research laboratory of Inco Technical Services Ltd. to address the need for flowsheet development with a limited amount of ore (such as drill cores). It consists of one rod mill, two regrind ball mills, one vibratory screen, 24 flotation cells of various sizes and two Venturi aerated flotation columns. The setup has continuous monitoring capability for pH, dissolved oxygen, oxidation-reduction potential, conductivity and temperature in conditioning tanks and flotation cells. Various options regarding flotation reagents, circuit configurations, and fineness of primary grind and regrind can be readily evaluated. The throughput of the miniplant is 20 – 30 kg/hour ore.Unit operations such as flash flotation, magnetic separation and gravity concentration can also be evaluated as an integral part of an entire flowsheet development.This communication describes the basic design features of the miniplant and some examples of applications are given.INTRODUCTIONInco operates numerous mines in Sudbury and Thompson and will shortly bring the Voisey’s Bay mine into production. It has long been recognized that the ores from different mines or from different depths of the same mine can give different responses in flotation. There is a growing need to properly evaluate the ores before feeding the mill to maximize the return of the mine/mill operation. Inco Technical Services Limited at Sheridan Park, Mississauga, Ontario has developed a batch laboratory procedure to address this issue. The results are considered in the overall economical assessment of new mine operations.For ores that cannot be processed by the existing mill operations or that will be processed by a new mill, it is necessary to develop a flowsheet that can maximize the economical return of the mine/mill operation. While recognizing the importance and contribution of the laboratory batch flotation procedure, it does not generate reliable data for flowsheet simulation and design. A full-scale pilot plant campaign is normally required to obtain the design data but often this is not possible due to a limited amount of ore obtainable from the drill core. A small-scale pilot plant (mini pilot plant or miniplant) capable of processing 20-30 kg/h ore can provide this data prior to a full-scale pilot plant campaign. A miniplant can also be used to optimize the circuit configurations, reagent additions and recycle options of process water before pilot plant work and can be used to test a different flowsheet configuration for an existing mill before re-piping a plant circuit."

Jan 1, 2003

By R. Demont, A. Pranesh, S. Rakheja

Ethical concerns of in-vivo procedures and poor repeatability of non-invasive techniques have been major limitations in estimating vibration-induced spine loads through experiments. The biodynamic models of seated human body exposed to whole-body vibration (WBV) have evolved for defining the frequency-weightings, enhancement of human responses to WBV, and developing anthropodynamic manikins for seating assessment activities. The widely reported mechanical-equivalent models, solely based on through- or to-the-body biodynamic response functions, do not seem to resemble the biomechanical structure and do not yield information on the dynamic loading and deflections of segments of concern, namely the spine. On the other hand, biomechanical models with representative anatomical structure and anthropometry are being attempted to simulate segmental movements and the coupling effects, using Finite elements (FE) or multi-body dynamics (MBD) formalisms, which could provide important insights into the inter-vertebral forces [1]. While the FE models pose considerable complexities primarily related to characteristics of the bio-material properties, the MBD technique with discrete rigid bodies offers the flexibility to create multi-segment models with relative ease and lower computational cost. In this study, a preliminary multibody dynamic model of a seated human body exposed to WBV along the vertical direction is formulated using MSC/ADAMS software. The model validity is demonstrated by comparing selected responses with the available measured data. Methods The seated human is represented by nine rigid body segments, including: head, neck, thoracic and lumbar torso, pelvis, hands and thighs, as shown in Fig. 1. The rigid bodies are coupled through different rotational and translational joints, some of which are force elements to allow vertical translations and sagittal–plane rotations of the segments. The measurements of transmission of vertical vibration through-the-body generally require subjects to voluntarily maintain a vertical head position to reduce head-accelerometer orientation errors. The head–neck–shoulder joint is thus considered to be rigid. The shoulders are assumed to be rigidly attached to the thoracic segment. The torso is made up of three (upper, middle and lower) segments connected by visco-elastic revolute and translational joints to permit relative pitch and vertical motions. The forces and torques generated by the joints are derived assuming linear stiffness and damping properties, which were identified from published studies. The pelvis is connected to the rigid seat by similar elements representing the visco-elastic properties of the buttock tissues. The two thighs are rigidly connected to the pelvis, while the segment masses are chosen from the anthropometric data for the 50th percentile male subject. The initial model parameters for the joints were obtained from [2]. The model was analyzed to determine the force-motion relationship at the buttock-seat interface expressed in terms of

Jan 6, 2006

By S. A. Abdel Sabour

Conventional methods for selecting a production plan for an open pit mine is based on the assumption that ore grades throughout mine life as well as market variables are known with certainty. Another important issue that is also being ignored in the conventional procedure is the value of management flexibility to revise operating policy with time according to the arrival of new information. Based on this oversimplification of reality, an optimum mine plan that is thought to be maximizing net present value (NPV) of the project is selected. Given the multiple sources of risk affecting the estimated NPV, there is a high probability that the actual value will be different from that estimated. This could mislead decision making process regarding selecting an optimum mine plan. This paper proposes a multi-criteria ranking system for selection between alternative mine designs under both geological and market uncertainties. The system is based on integrating multiple market and geological uncertainties as well as the operating flexibility to revise the ultimate pit limits using a Monte Carlo-based real options valuation (ROV) model. To compare the methods, the article applies the proposed system, along with the conventional NPV-based method, to rank possible mine designs for a copper and a gold mine. It has been found that, considering multiple risk analysis measures while integrating uncertainty and operating flexibility results in selecting a mine design that is different from that selected by the conventional method.

Jan 1, 2009

By Bright Oppong Afum, Kojo Boakye, Kwaku Boakye

This research developed and simulated a novel multi-indicator Fatigue Detection and Alert System (FDAS) designed to enhance fatigue detection accuracy in mining environments. The system integrates a comprehensive set of inputs: eye blink rate, eye closure duration, yawning frequency, distraction levels, Pre-shift Check-in Scores (Self-report) and Electroencephalography (EEG) Levels. Using MATLAB’s Fuzzy Logic Rule Viewer (FLRV) and Simulink, simulations demonstrated the FDAS’s robust ability to process these diverse physiological and behavioural indicators accurately. It effectively classified operator fatigue into low, moderate, and high fatigue levels, consistently providing appropriate outputs and corresponding intervention recommendations across various mixed-signal scenarios. The system achieved a calculated accuracy of 85.19% across 27 test entries, with a standard deviation of approximately 1.8459, confirming its reliability for real-time fatigue monitoring. These findings highlight the significant potential of this fuzzy logicbased approach to proactively identify early signs of fatigue, substantially enhancing safety and operational efficiency in demanding mining operations.

Feb 22, 2026

By G Hancock, J Lowry, T Coulthard, W Erskine, M Saynor

An important part of planning for the rehabilitation of uranium mine sites is the ability to assess the geomorphic stability of the final landform, over time frames ranging from decades to millenia. Depending on the environmental conditions, erosion features such as gullies may incise into containment structures, potentially leading to the exposure and transport of encapsulated radioactive material. Further, erosion may lead to increased sediment loads and the transport of other mine-related contaminants off-site and into downstream waterways. While erosion may be monitored and assessed over the short term (years to decades), the longer-term behaviour (centuries to millennia) of such landscapes is not within any meaningful human management time frame. Landscape evolution models (LEMs) can provide information on soil erosion rates at decadal or centennial scales over large spatial scales, and evaluate the sensitivity of these processes to environmental changes. However, an important issue associated with the use of models is the ability to assess the reliability and accuracy of the model. In this paper, the CAESAR-Lisflood LEM is tested for its ability to predict soil erosion from a series of 30 m × 30 m experimental plots specifically constructed for this purpose on a trial rehabilitated landform at the Ranger Uranium Mine in the Northern Territory, Australia. Model predictions of bedload and suspended sediment loads from the erosion plots were compared with field measured observations collected over four wet seasons from the trial landform. Once calibrated for the specific site hydrological conditions, the predicted sediment yield – specifically, bedload – demonstrated an excellent correspondence with the field data. However, longer-term simulations of ten years identified an exhaustion effect in sediment yield from the landform. These latter results indicate that a weathering function needs to be incorporated into CAESAR-Lisflood to ensure confidence that the CAESAR-Lisflood LEM will be able to correctly predict the long-term evolution of a rehabilitated landform once it has been?constructed.CITATION:Lowry, J,?Saynor, M,?Erskine, W, Coulthard, T and Hancock, G, 2014. A multi-year assessment of landform evolution model predictions for a trial rehabilitated landform, in Proceedings Life-of-Mine 2014 , pp 67–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014