Search Documents

By Ruilin Yang

"Blast vibrations are essentially a strain/stress wave propagating in rock or structures inthe vicinity of a blast. However, blast vibration has always been quantified in terms ofpeak particle velocity (PPV) or acceleration (PPA), and a meaningful relationshipbetween blast vibration and strain/stress has not been established. The determination ofthe dynamic strain from blast vibration may improve quantification of blast damage andselection of a blast vibration limit for critical structures or high walls. Dynamic strainrelates to rock mechanics or material strength more directly than peak particle velocity(PPV). This paper documents a method to calculate the three-dimensional dynamic straintensor from recorded blast vibration signals. The method is based on determination of thedisplacement gradient at a point of interest for each time instance during the vibrationduration. The method to calculate dynamic strain is applicable to generic seismicwaveforms including near and far field blast vibration from a production blast withmultiple blast holes. In order to minimize measurement errors the specifications of thespacing between monitors and the sampling frequency of the vibration recording aredescribed."

Jan 1, 2012

By Kugan Kuganathan

Pastefill is being increasingly considered as a viable fill by underground mine operators. Mount Isa Mines (MIM) chose pastefill to fill their deep copper mine (>1200m deep) after considering various other types of fill in the feasibility studies. During the development of pastefill at Mount Isa (1996 - to date) the Mining research of MIM developed two cost effective, reliable and simple testing methods and used. With the help of these tests the behaviour of MIM pastefill was studied thoroughly and the most optimum mix design for pastefill was achieved. The MIM's pastefill plant, the largest in the world with a capacity of 450rph continuous pastefill production and unique in the process used, has been built (1998-1999) to produce pastefill to the specification developed through extensive testing program using the Flow Cone and Mini Slump cone Tests. As a consequence, it is now possible to select the optimum pastefill mix designs and predict their flow behaviour in bore holes or pipe lines using only these tests. MIM Blended Tailings Pastefill (BTPF) uses 3-3.55 Portland cement and the cost of pastefill is much lower than the total tailings pastefill, that could be produced from the same tailings.

Jan 1, 2001

By Kanchan Mondal, Anthony (Sam) Spearing, Gopi Bylapudi, Joseph C. Hirschi

"The U.S. coal mining industry uses about 100 million rock anchors per year. ASTM F432 specifies the requirements for rock bolts on mines but does not address corrosion. Corrosion has been found to be an issue in Australian coal mines (Hebblewhite et al., 2003 and Villaescusa et al., 2007), where the problem has been researched and stress corrosion has been found to be a significant cause of rock falls. Corrosion is also a major concern for underground civil construction in the U.S. but has not been considered an issue or adequately researched in coal mines. Underground conditions are conducive to corrosion mainly because of water quality and humid conditions. There is a perception, however, that when bolts are fully grouted, adequate corrosion protection is offered to the steel. Research has shown that this is not necessarily the case, due to the formation of micro-cracks as the resin sets and with subsequent rock movement shearing the resin column. This paper outlines a method to determine the corrosion potential of bolts used in long-term excavations and suggests ways to mitigate such effects based on research conducted in the lab and on three mines.INTRODUCTIONResearch on rock anchor corrosion in mines has not been extensive enough in the past, and the effects of several factors in the mine atmosphere and waters are not clearly understood. One probable reason for this lack of research may be attributed to the time required for gathering meaningful data, which makes the study of corrosion quite challenging.Almost all the rock bolts used in coal mines are made from steel, hence the corrosion of iron needs to be understood. The corrosion of iron is an electrochemical phenomenon with the overall equation"

Jan 1, 2010

NIOSH is conducting research to reduce the silica dust exposure of workers at surface coal mines. One goal of this research is to evaluate the relationship between drilling parameters, rock strata and silica dust generation. This study involved measuring blast hole emission dust from a rotary drill rig which required sampling high concentration dust (>400 mg/m3) for silica content in a high velocity airstream. To measure dust initially, traditional sampling methods using personal sampling instruments were attempted in and around the shroud area of the drill with no success. Variations in the dust cloud concentrations under the shroud, the condition of the shroud and its orientation over the hole, and ambient air conditions prevented consistent and accurate dust measurements from being obtained. Amore consistent dust cloud is necessary for accurate measurements. An area of the drill’s dust collector system that consistently draws the emitted airborne dust from the hole is the collector tube. This tube connects the drill collector’s vacuum and dust filtration system to the shroud area. Assuming the collector system is working as designed, sampling from the collector tube would enable more consistent and accurate samples to be taken. However, current personal samplers are unable to sample in the concentrations and velocities experienced in the collector tube, so another method had to be devised. To achieve the desired results, an in-stack cascade cyclone was used. Preliminary field testing shows positive results.

Jan 1, 2003

By O. J. R. Baena, I. C. Sánchez, J. L. G. Guzmán

Frontino, a municipality in western Antioquia, Colombia, has more than 200 years of mining tradition. Currently, mining activities are carried out for lode gold using subway tunnels, where the grinding of the material is done in "cocos", whose energy depends on internal combustion engines and ACPM, environmentally polluting and inefficient methods. In accordance with the Sustainable Development Goals as an initiative developed by the UN, different mining methodologies that are aligned with these are constantly being analyzed. This study proposes to eliminate the use of hydrocarbons in artisanal mining, mainly promoting Sustainable Development Goals 7, 9, 11, 12, and 13. This will be achieved through an energy transition to renewable energy sources that take advantage of the topography and water resources of the area, providing advantages to the communities that live there, such as lighting, electricity for cooking, ventilation for mines, etc

Mar 2, 2022

By Ajay K. Singh

The surface quality demands for galvanized and galvannealed steel sheets by the automotive and appliance industries have been getting increasingly stringent over the past few years. Intensive efforts by Hot-Dip-Galvanizers to meet these demands have resulted in substantial improvement to the hot dip coating process. However, elimination of zinc bath contaminants which directly affect the coated strip surface quality continues to remain a tough challenge. As part of our effort to improve the zinc bath cleanliness, Inland Steel Company has developed a test method to quantitatively measure the contaminants in incoming zinc spelters and establish a specification for incoming zinc quality. The test is currently being used for auditing the incoming zinc quality. The zinc suppliers are also using this test for quality control purposes. The purpose of this paper is to describe the test method and how it has improved the galvanizing operation at Inland.

Jan 1, 1992

By M. A. Oskouei

Draglines are dominant machines and the most electricity consumers in surface coal mines. With the growing price of energy, environmental concerns, and the high sensitivity of mine profitability to dragline productivity, any improvement in efficiency of draglines can be beneficial for mines. Research has shown that operator skills have a significant impact on energy efficiency of loading machines. This study suggests a method to identify the key parameters that lead to differences in operator energy efficiency (responsible parameters). First, correlation analysis is used to identify parameters that are correlated to energy efficiency. Second, linear regression of a difference matrix is used to determine responsible parameters. Since this method is based on pair-wise comparison of operators, equal number of cycle is required for pairs of operators. Complete case analysis (CCA) is used to handle missing data problems. The final conclusion is made after removing the effect of random sampling and by considering all pairs of operators. Identifying responsible parameters can improve operator training programs. The suggested method is illustrated with a case study using field data.

Feb 23, 2014

By Nikolaos Petropoulos, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature. In this study, pure emulsion was tested in confined conditions to better simulate the behavior of the detonation of the explosive in rock mass conditions. A methodology is proposed for carrying out the evaluation of the explosive performance. The blasthole diameter of the samples varied from Ø 25 mm (0.98 in) up to Ø 65 mm (2.55 in). The confiner was a magnetic mortar cylindrical sample with mechanical properties similar to a rock mass. A streak camera and VoD probes were used to measure detonation front curvature and VoD. The data was analyzed and correlated with the physical parameters of the explosive. Additional to this, the data was further used to calibrate numerical models in LS-Dyna.

By B. Erdem, N. Çelebi

An important problem associated with tandem dragline systems is that of matching the productive capability of individual draglines in the combination. In this paper, a dependence mechanism among draglines in a tandem system is described, and possible consequential problems in a poorly-matched system are defined. The rate of linear advance and the cost of stripping are determined as two major indications for an efficient operation. The proposed decision criteria and the underlying mechanism to select a synchronous couple are introduced and used in simulating tandem dragline systems. The developed model is tested on a hypothetical strip mine where pullback stripping is applied with a tandem dragline system.

Jan 1, 1999

By J. A. Botín

Identifying, quantifying and minimizing technical risks associated to investment decisions is a key challenge for the minerals industry decision takers and investors. However, risk analysis in most bankable mine feasibility studies are based on stochastic modelling of project NPV which, in most cases, fail to provide decision makers with a truly comprehensive analysis of risks associated to technical and management uncertainty and, as the result, are of little use for risk management and project optimization. This paper presents a value-chain risk management approach where project risk is evaluated for each step of the project lifecycle, from exploration to mine closure, and risk management is performed as part of a stepwise value added optimization process.

Jan 1, 2011

By G. Esterhuizen, C. Karacan

Methane can be a significant hazard in coal mine longwalling operations and extensive methane mitigation techniques are employed by coal mine operators. Reservoir modeling techniques are used to better understand the liberation and migration of methane from the surrounding rocks towards the mine ventilation system. The caved rock behind the advancing longwall face, known as the gob, can contain high void ratios, providing high permeability flow paths to the methane. The gob is progressively compacted by the weight of the overburden, resulting in a reduction in the void ratio and associated permeability. Estimating the permeability distribution within the gob poses challenges due to its complexity. The authors have developed a new methodology to determine both horizontal and vertical variations in the permeability of the gob. Variations of the permeability in the vertical direction are based on a model of caving and block rotation, which considers the effect of block dimensions and fall height on the void ratio. Gob compaction by the overburden and associated permeability changes are determined from a three-dimensional geo-mechanical model which simulates the gob as a strain hardening granular material. The resulting three-dimensional permeability distribution in the gob is then transferred to a reservoir model. The paper demonstrates the application of the method and shows that reasonable results are obtained when compared to empirical experience and measurements.

By H. Dong

This paper presents a heat conduction model to determine the erosion profile of freeze linings in a ferronickel submerged arc furnace. Kirchhoff transformation was adopted to simplify the nonlinear equation governing heat conduction. The boundary element method (BEM) and Nelder-Mead simplex optimization method were employed to solve an inverse heat conduction problem. Erosion profiles could be obtained when calculated temperatures at sensor locations agreed well with measured temperatures. The model was validated by comparing the heat loss through the linings, which was calculated by BEM and integral operation after erosion profiles were obtained, with the value calculated from industrial data such as actual power consumption, tap-to-tap time, and ferronickel output. The optimal solution for the erosion profile could be acquired when the difference in heat losses calculated by these two methods is at a minimum.

Jan 1, 2014

By H. Kim, R. W. Plummer, T. J. Stobbe, W. G. Jones

"Exposure to airborne dust in coal mines has caused respiratory disease in coal miners. The causal agent in these diseases remains unknown, although the minerals found in and around the coal seam have been implicated. Toxicological studies designed to establish the effect of different mineral combinations and concentrations are lacking because the mineral content of coal mine dust has not been defined. This paper reports the initial results of a study done to characterize the mineral content of the coal mine dust found in a mine in the Upper Freepott seam in Northern West Virginia. Coal mine dust samples were collected using 4- stage cassette impactors at nine locations in the mine. The samples were analyzed by an x-ray microdiffraction film technique supplemented by energy dispersive scanning electron microscopy. Primary size modes of about 17 to 20 micrometers from the samples collected at the haulageway and the returnside of the continuous miner were found. From the returnside of the roof bolter samples, a primary size mode of 12to15 micrometers was measured. The minerals found in high percentages were illite, kaolinite, quartz, and calcite. The distribution of minerals in inter· and intra- location samples showed wide variations. Trends in these variations are presented. Stobbe, T. J.; Plummer, R. W.; Kim, H.; Jones. W.: Characterization of coal mine dust. Appl. Ind. Hyg. 2:95· 100; 1986. IntroductionDisease-associated dusts in coal mine environments continue to afflict miners in today's modern mines. The relationship between exposure to coal mine dust and the development of various respiratory diseases has been well recognized; however, the reasons for variation in occurrence of these diseases among miners in different geographic areas,(1) rank of coal seams,(2-3) and jobs (4) remain uncertain. Several papers have reported on the causal agent in the development of these diseases. Davis (5) found that the percentage of the non-coal minerals present in the lungs of deceased miners increased as the level oi pneumoconiosis became more severe. Reisner (6) reported that cell damage caused by coal mine dust increases with the mineral and quartz content of the dust and with the geo· logical age and rank of the coals. Two studies, investigating the in vitro effects of mineral dusts. reported by Seemayer and Manojlovic (7) also obtained positive correlation between cytotoxicity and the mineral content of coal mine dust. Gormly (8) postulated that destruction of macrophages by certain mineral dusts is the first step in the development of pneumoconiosis. In 1980, Adamis and Timar (9) reported that quartz. sandstone, slate. respirable colliery dust. bentonite, illite, and some kaolins had cytotoxic effects on rat peritoneal macrophages""in vitro."" Walton,(10) however, reported that the presence of high clay, illite, and kaolin mineral exposures reversed the hazards associated with increasing quartz exposures. This finding was supported by Le Bouffant and coworkers.(11) They reported that illite present in coal mine dust strongly inhibited the pathogenic effects of quartz while kaolin had a weaker inhibitory effect."

Mar 1, 1989

By Dion Pastars

Kestrel Coal has undertaken a surface-to-seam consolidation program of faulted ground prior to longwall retreat in the 304 panel. Micro fine cement is used to improve the rock mass quality and therefore reduce the risk to personnel and equipment whilst increasing previously assumed sterilised reserves. The program is based on information attained from previously successful grouting campaigns in the Queensland coal area and follows the decision making process to ensure there is sufficient spatial permeation of cement across the faulted area. This data is used to assess the residual risk to the business in terms of health, safety and production

Jan 1, 2007

By L Keeney

Geometallurgy is not a mechanism designed to replace current geological and metallurgical deposit characterisation but an added component required to understand orebody variability. Current geological characterisation approaches focus on understanding deposit genesis aimed at identifying new mineralised regions and metallurgical characterisation determines parameters required for engineering design of processing plants. Geometallurgical integration has the task of drawing on aspects of each stream to enable spatial mapping of performance indices across a deposit. It is a complimentary activity to current practice and adds a new dimension to orebody knowledge. Although the notion of conducting an integrated geological and metallurgical analysis is not a new concept, limited publications exist in the field proposing integrated methods, with several technical issues existing in current geometallurgical integration approaches. An iterative method drawing on existing geological and metallurgical characterisation and new measurement tools and inputs is proposed. The integrated method comprises of discrete components dynamically linked together through iterative feedback loops with each component having a specific purpose achieved by applying a range of data acquisition technologies and statistical tests. The key outcomes of the method are:overcoming the lack of optimised geometallurgical domains relevant to processing performance,development of a rigorous approach to identifying parameters controlling processability,improved protocols for relevant metallurgical test data and sample selection, andability to generate greater data support to enable rigorous geostatistical modelling of geometallurgical attributes. This paper outlines the integrated mapping and modelling method developed and draws on multiple data acquisition technologies applied within the AMIRA P843 GeMIII Project.

Sep 5, 2011

By Dave Ecobichon, Éric Côté, Simon Nickson, Michel Leclerc

The feasibility assessment of a mineral deposit requires the construction of a geo mechanical model of rock mass properties, for the purpose of preliminary mine design. The Noranda Technology Centre has been involved in the development of geomechanical models for several mineral deposits at the feasibility stage. Each model is constructed through intact rock testing, geotechnical core logging, geotechnical mapping and rock mass classification. Rock mechanics principles are used to develop conceptual stope designs and propose possible mining sequences. This methodology is applicable to both new mining projects and to the development of new areas within anoperating mine. This paper explains how the geomechanical model is developed and reviews its application to several case studies.

Jan 1, 1996

By S Durucan, A Korre

The application of simple methods of statistical analysis, coupled with geostatistical analysis and geographic information systems, can only summarise and give an outline of the spatial distribution of the parameters measured. Spatial analysis of the components or factors calculated, through principal component analysis or factor analysis, allows assessment of the geographical distribution of the dominant processes contributing to soil composition and/or contamination. Neither of these tools, however, distinguishes between the different sources of pollution. The application of canonical correlation to the data, driven by expert appraisal of the potential pollution sources, allows their quantitative and spatial assessment while GIS provides the environment in which to organise and present the results. The methodology is illustrated by its application to soil-contamination data from the Lavrio area in Greece, where silver-bearing orebodies have been mined for more than 25 centuries

Jun 21, 1905

By I. Westermann, K. Marthinsen, M. S. Remøe

"Al-Mg-Si alloys often add small additions of e.g. Mn or Cr, to form dispersoids, which may act as nucleation sites for Mg2Si particles after homogenization. The purpose is to ensure a high density of uniformly distributed small ?’-particles, which can be dissolved during further processing prior to the final age hardening step. However, their density and spatial distribution are critically dependent on the homogenization procedure. It is therefore important to have a robust and reliable method for assessing their spatial distribution. In the present work an existing methodology for assessing spatial uniformity, the Global Shannon Entropy (GSE), has been implemented and evaluated for different dispersoid structures characterized by scanning electron microscopy. This metric is highly dependent on the parameters used, but by careful selection of adequate parameters, it can be effective in detecting non-uniformity. An important weakness with the GSE was identified, and a modification to improve on the ability to differentiate degrees of non-uniformity is suggested. To evaluate the proposed methodology, the effect of heating rate on dispersoid precipitation behaviour during homogenisation of four Al-Mg-Si alloys with different Mn/Cr-content has been investigated. The metric with the new term has demonstrated promising results, and improved the ability to differentiate degrees of spatial uniformity.INTRODUCTION Al-Mg-Si series alloys are the most common aluminium extrusion alloys and are attractive for applications in a range of sectors (e.g. construction, automotive and recently also in consumer electronics), due to their generally good combination of strength, ductility and corrosion resistance. However, their extrudability and end properties depend critically on the alloy chemistry as well as prior processing conditions. Coarse ß-AlFeSi or Mg2Si-particles typically have a detrimental effect on extrudability, while small dispersoid particles may affect recrystallization, grain growth and precipitation of Mg and Si. The strengthening potential in the final age hardening step depends strongly on the amount of Mg and Si in solid solution after extrusion. The manner in which these particles are spatially distributed will decide whether the final product will exhibit uniform properties, and the number density and sizes will determine the extent of the effect. As such, these are important characteristics."

Jan 1, 2018

By W. J. Birch, D. Leckenby, R. Farnfield

The use of electronic detonators to improve fragmentation is becoming universally accepted. However their use in limiting peak particle vibrations levels is still in its infancy. Most of which is anecdotal, in that few actual scientific studies have been carried and published. This paper details the research work carried out at a limestone quarry in the County of North Yorkshire in Northern England. Here a series of blasts were carried out some used non-electric detonators whilst others used electronic detonators. The majority of blasts were carried out at the same burden, spacing and deck charge weight loadings. Initially, the key variable was the difference in detonator type and then leading on to using the electronic detonators at specific exact different detonator timing intervals. Later the study was extended to include double row as well as single row blasts.

Jan 1, 2007

By John S. Wakeman

The initial step in the pelletizing of iron ores is the production of green balls. The importance of this step cannot be overemphasized as the physical quality of the green balls has a very significant effect on the subsequent induration process, regardless of the type of the indurating equipment employed. The ability of the green balls to withstand the rigors of handling, distribution, compaction and drying will have an effect on the degree of success of any pelletizing operation. Many factors affect the physical quality of the green balls including the prior processing of the iron ore, the characteristics of the balling feed and the type and quality of the binder used (if any). When working on the development of a new project or studying an existing operation, it is often desirable to determine what effect variations in these factors will have on green ball quality. It is generally impractical to make these determinations on a commercial, or even pilot plant scale, especially when the number of variables to be studied is large. Because of this, many organizations have developed batch techniques for producing green balls to enable them to perform such investigations with a minimum of time and expense. The batch balling method is at best, only an approximation of commercial balling systems. Many practitioners employ the use of pre-formed seed pellets to initiate a batch run. Thus, the growth mechanism encountered in any experiment is essentially snowballing. Unless an instability is introduced into a balling test (such as an excessive initial feed rate or an unusual feed material characteristic) the growth mechanism of coalescence is not present to a significant extent nor is it desirable. In a continuous operation, both mechanisms are present and necessary to sustaining the system. The batch balling technique thus produces pellets in an idealized manner and cannot be used to directly predict commercial green ball qualities. A general relationship does exist however, and the procedure is fairly sensitive to variations in test parameters. Although many refinements to this technique have been introduced over the years, batch balling is still essentially an art and subject to "operator effect". Therefore, to assure consistant and reliable results, skilled technicians who carefully adhere to established practice must be utilized.

Jan 1, 1971