Search Documents

By D. Tang

The froth zone in a flotation cell is recognised as a region which contributes to the overall flotation performance. Froth recovery is a measure of the efficiency with which the froth phase delivers particles arriving at the pulp-froth interface to the concentrate. Poor froth recovery in scavenger stages is generally attributed to poor froth stability. The key indicators of froth performance: froth recovery, entrainment and water recovery were measured in an OK3 pilot cell installed at a zinc concentrator in Australia and supplied with scavenger feed. Cell hydrodynamic and pulp chemical conditions during the operation of the cell were also measured as well as bubble growth across the froth phase. The objective of the work was to assess the impact of a number of commercial frothers on the froth performance in the OK3 cell and assess the suitability of using bubble growth as an indicator of froth stability.

Jan 1, 2014

By F D. I Hodgson

Twenty-seven observation test pits were excavated at four different spoils dumps at three collieries in the Witbank Coalfield. The holes were dug into the upper three metres of the spoils to ascertain if any weathering profiles, variation with age or influence of topsoil covering could be gauged. Samples from these holes were also subjected to laboratory testing (ABA, humidity cells and mineralogy on several selected samples). The test pits showed that there was a good correlation between in situ paste pH-values and ABA results for samples taken from the pits. At all the collieries, no correlation between age of spoils and in situ acidity could conclusively be drawn. The depth of soil cover also appears to be a minor consideration in determining the eventual acidity of the spoil. In the pits where acidity was found, the weathering was evident when contrasted to areas still buffered. It is unclear if the weathering leads to the acidity or vice versa, as the soil covering appeared to be similar. The spoils proved to be extremely variable with regard to particle size and material on a micro and macro scale. Evidence from most of the holes suggested that there was enough water contained in the fine material in the spoils to support the initiation of acid generation. Conclusions from this investigation are that the mineralogy of the spoils is the most important factor in determining the eventual occurrence of acidic hotspots, and that prior characterisation and selective handling will provide the best management practice for these spoils.

Jan 1, 2003

By L Matthews, D O’Dea, P C Hayes, J Manuel, B Monaghan, T Honeyands, D Pinson, J Leedham

Many different approaches have been used in the past to characterise iron ore sinter mineralogy to predict sinter quality and elucidate the impacts of iron ore characteristics and process variables on the mechanisms of sintering. Characterisation techniques include optical image analysis and point counting, X-ray diffraction and scanning electron microscopy. Each technique has its advantages and disadvantages depending on the objectives of the measurement. It is generally acknowledged that silicoferrite of calcium and aluminium (SFCA) is very important to the quality of the sinter produced; however, strict definitions of the phases and textures of SFCA are not generally agreed. This paper summarises the state-of-the-art in sinter characterisation applied in Australia by both academics and industrial researchers. The results from various techniques are compared and the relationships between the measurement results are discussed.CITATION:Honeyands, T, Manuel, J, Matthews, L, O’Dea, D, Pinson, D, Leedham, J, Monaghan, B, Li, H, Chen, J, Hayes, P C, Donskoi, E and Pownceby, M I, 2017. Characterising the mineralogy of iron ore sinters – state-of-the-art in Australia, in Proceedings Iron Ore 2017, pp 49–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D J. Bradshaw, E M. Wightman, C L. Evans, B Triffett

During the commissioning phase of Prominent Hill, periods of reduced recovery were experienced with higher-grade ore blends. This was unexpected and as part of the process to identify the cause, surveys were conducted in May 2009, with two different ore blends (copper grades: 1.94 per cent Cu (blend 1) and 2.49 per cent Cu (blend 2)). Metallurgical performance was assessed in terms of rougher recovery and grade with consideration of both pulp and froth effects. In addition, hydrodynamic measurements (gas hold up, bubble size, superficial gas velocity) as well as measurements of bubble load and top-of-froth grade were taken during the surveys and full mineralogical assessment of selected streams completed to characterise the nature of the differences. The metallurgical results showed that the lower performance was obtained with blend 2 which contained the higher amount of chalcocite and was higher-grade. Analysis of the survey data showed that for both ore blends more than half of the copper loss occurred in the +38 ¦m size fractions. Almost 30 per cent of the copper in the +38 ¦m fractions that reported to the rougher tails during processing of blend 2 was liberated compared to less than five per cent for blend 1. Additionally almost 60 per cent of the copper in the +38 ¦m fraction of blend 2 was chalcocite compared with approximately 20 per cent in blend 1. This paper discusses the sensitivity of the chalcocite-to-surface chemistry effects causing marked reductions in recovery either through reduced pulp recovery or froth phase (detachment) effects. The reagent suite and operating conditions were subsequently changed and the recoveries increased substantially and the sensitivity to ore changes eliminated. It should be noted that subsequent optimisation work, which focused on recovery improvement, has led to copper recoveries of over 90 per cent being achieved.CITATION:Bradshaw, D J, Wightman, E M, Evans, C L and Triffett, B, 2012. Characterising the reasons for the difference in performance of two ore blends in early processing at OZ Minerals Prominent Hill Operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 273-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Nic Slatalla

Acoustic emission monitoring techniques are a powerful tool for analysing deformation behaviour and fracture characteristics of rock samples under uniaxial loading. Uniaxial compression tests were carried out on three different types of sandstone for a better understanding of acoustic emission response with respect to rock deformation and damage develop-ment. All sandstone samples revealed congruent characteristic acous-tic emission patterns which correlated directly with distinct stress-strain stages. However, the acoustic response and development within the individual stages proved to be entirely different due to variations in their microstructure.

Jan 1, 2008

By Joseph Moses Botbol

Two methods are developed whereby; (1) mineralogic data can be arranged in order of typicality, and (2) mineralogic data external to a model can be compared with the model and the degrees of association computed. Thirty arbitrarily selected base metal mining districts in the conterminous United States were classified as copper, lead, or zinc districts on the basis of tonnage of the major base metal produced. For each of the copper, lead, and zinc districts binary-occurrence distributions were compiled for primary (unoxidized) and secondary (oxidized) minerals. Primary and secondary minerals were then arranged in order of decreasing typicality. Model copper districts are most typified by primary chalcopyrite, pyrite, and secondary malachite. Model lead districts are most typified by primary galena, quartz, pyrite, sphalerite, and secondary anglesite and cerargyrite. Model zinc districts are most typified by primary sphalerite, galena, pyrite, quartz, and secondary smithsonite and cerus-site. The Park City district was removed from the model and its primary and secondary mineralogy was compared with the model copper, lead, and zinc districts. The primary mineralogy of the Park City district is about equally associated with the model copper and lead districts, but the secondary mineralogy is much more akin to the model copper districts. Thus, with respect to the model data, the geochemical target presented by the Park City district resembles a copper district more closely than a lead district.

Jan 1, 1969

By Guangwei Wang, Changle Zheng, Yifan Chai, Jian Guo, Weiwei Geng, Jianliang Zhang

In this paper, characteristic and kinetics of CO2 reaction with four different kinds of coke such as top-loading coke, dry quenching tamping coke, wet quenching tamping coke and semi-coke were investigated based on isothermal method. Electric resistance reduction furnace was used to heat the sample. Volume Model (VM) and Shrinking Core Model (SCM) were used to calculate the kinetic parameters and to contrast with the experimental results. The results showed that the Volumetric Model (VM) was much suitable for the reaction of top-loading coke, dry quenching tamping coke and wet quenching tamping coke, while Shrinking Core Model (SCM) was much suitable for semi-coke.

Jan 1, 2015

By L. M. English, Y. J. Wang

When plotted as head vs. volume, fan curves start high and decrease in head with increasing volume while mine head curves start low and rise with increasing volume. Their intersection is the system operating point. But wait a minute: Isn't head loss a negative number, a debit? And isn't fan head an energy addition, a credit? This, as every ventilation instructor knows, is often a stumbling block to student or audience comprehension. It is possible to use the intuitively correct curves - pressure losses as negative values and energy additions as positive values-and still obtain the correct operating point: adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at which the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure; with the standard approach it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel circuit or ventilation network. The results are the same, and the approach is logically consistent and less confusing.

Feb 24, 1997

By T. T. Wang, T. H. Huang, Y. C. Chiu

Quantitatively analyzing deformation of a tunnel with lining anomalies for structural safety evaluation is essential for sustainable tunnel engineering. However, a complete theory and associated methodology accounted for displacement of a built tunnel is absent. This manuscript introduces a novel characteristic matrix method proposed by the authors which is an integrated procedure that analyzes displacement of rock tunnels in operation. First, establish a numerical model expressing a specific state of the tunnel in interest. Derive the characteristic displacement modes by a unit disturbances and check their independency. Once the characteristic displacement modes are proved to be orthogonal (independent), they are ready for use. Given a tunnel displacement, modal decomposition returns the magnitude of each characteristic displacement modes that together consist the given displacement. By realizing the definite value of horizontal and vertical translation, rotation, uniform compression/expansion, elliptic deformation, triangular deformation…etc. for a tunnel displacement, one can distinguish tunnel displacement and deformation types from their modal composition. A circular tunnel with elastic structure and surrounded by elastic rock mass is chosen to demonstrate the outcome of characteristic modes and how they work. The influences of tunnel shape, elastic modulus ratio between rock mass and tunnel structure, and numbers of monitoring points on a tunnel profile were also discussed. Identifying possible tunnel deformation causes is attainable if further connections between mode combination and force increments were built.

Jan 1, 2015

By Charles R. Boardman

Recent underground nuclear tests in tuff, alluvium, salt, and granite have yielded data essential to the evaluation of mining applications of contained nuclear detonations. The data indicate that for these media the cavity radius is predictable within ±20% without regard to the properties of the rock in the immediate shot environment. Properties of the chimney of broken rock resulting from collapse of the cavity, on the other hand, are found to be related to the properties of the rock and its preshot structural weaknesses. Seismic effects and radioactivity distribution are sufficiently documented to serve as a basis for predicting the safety conditions associated with detonations for a variety of yields.

Jan 1, 1964

By Sudhir Kumar Das

"The exorbitant price of the land in the metropolis has restricted the horizontal expansion and compelled the owners, the developers and the engineers to opt for vertical expansion. This has resulted in the construction of high rises by extending floors of the existing buildings and developing the new ones for which deep excavation is a must. The multistoried buildings up to a certain height can be founded on shallow depth if the soil beneath can withstand the load. If not, the soil can be stabilized by the latest improvement technology to change the properties of soil to cater the desired load of the superstructures. By such practice the cost and time of completion of the substructures can be reduced in comparison to the substructures needed for deep excavation.The necessity of deep excavation cannot be ignored to create housings, underground parking lots and the other public amenities for the urban migrants in the metropolis.Although most of the metropolis have underground mapping the developers, before starting excavation should be hundred percent sure about the alignment and depth of the utilities so that the excavators do not snap the same to bring cut in water supply, power lines, telephone lines etc, resulting in hue and cry in the neighborhoods of the metropolis due to no availability of the essential services The building/structures coming on the influence zones of the deep excavation should be monitored in all sequences of excavations. In case of building underground corridors for rail or road through open deep excavation under a traffic road the developers, before commencing excavation should shift/divert the dry and wet utilities coming on the way of excavation to suitable locations. The surface traffic need to be diverted either temporarily to an adjacent alternative road or allowed to pass over a decking built over the trench of excavation for the affected length of construction. The soil support system is necessary longitudinally on the two sides covering the width of trench for building corridors. In case of building substructures of flyovers built at different plots along the alignment of the flyover or a multistoried complex built at an isolated plot, the soil support system would be necessary on all the sides covering the plot of construction.The material of construction of soil support depends on the depth, type of soil and the type of permanent structure to be developed. Probable geo-hazards inviting casualties in the deep excavation projects occur due to caving of soil, leakage of wet utilities, seepage through honey comb concrete surfaces, failure of pump used for dewatering etc. A detailed comprehensive planning, management and determination of the project authority is essential for marginalizing the casualties. These prevent unforeseen expenditure in mitigation and help to control the time and the cost over run of overall project. The engineer at site should be more a professional manager than an engineer at site. He should be conversant with the safety and environment rules and regulations applicable to deep underground projects."

Jan 1, 2015

By Yuanbo Zhang, Qian Li, Helei Zhang, Heng Yu, Guanghui Li, Tao Jiang

"Large reserves of specularite iron ores have been found all over the world, which is characterized by high total iron grade, low gangues content, as well as low commercial price. However, it has not been widely used in sinter or pellet production due to its inferior sintering and roasting behaviors. It has shown that the proportion of specularite ores was increased as high as 40%~50% and good results was achieveed by using Composite Agglomeration Process (CAP), an innovative agglomeration process invented by Central South University. But the mineralization of specularite is still unknown during composite agglomeration processing. In this paper, the induration characteristic of specularite ore is studied by simulating CAP in laboratory, as well as microstructure analysis of CAP product. The results show that specularite pellet is mainly indurated through recrystallization of Fe2O3, calcium ferrite within high basicity sinters matrix interweaves with the recrystallized Fe2O3 on the surface of the pellet, which forms an integral microstructure, and ensures high strength of CAP product for ironmaking.IntroductionLarge reserves of specularite iron ores have been found all over the world, especially in Minas Gerais of Brazil, Xuanhua city and Anshan city of China, Elba island of Italy, St.Gotthard of Switzerland, Cumberland of Britannic, and so on. The specularite ores have a smooth surface, as well as a good crystallization and dense texture. When specularite is used to produce pellets, the specularite ore grains are difficult to adhere onto green ball due to its poor ballability. Moreover, specularite pellet requires high roasting temperature over 1300°C [1]. When specularite ore is used in sintering, the permeability of sintering bed gets bad and the quality of sinter is diminished. The practice in a few sintering plants finds that the output and strength of sinter decrease with the increase of specularite proportion, and the consumption of coke increases [2-4]. Therefore, the utilization of specularite has been limited. Composite Agglomeration Process (CAP) is an innovative technology invented by Central South University [5-7]. The process has the following merits: making reasonable utilization of different iron ore resources; improving the quality and output of sinters; manufacturing sinters with low basicity; significantly reducing energy consumption, etc[8-9]. It has been shown that large proportion specularite ores, as high as 40%~50% can be used well by CAP [10], but the mineralization of specularite pellet is still unknown during composite agglomeration processing. In this investigation, the induration characteristics of specularite ore pellets is studied by simulating CAP in laboratory, and the phase composition and microstructure of CAP product are also characterized by using microscope and Leica image analyzer (Germany, Leica DM RXp)."

Jan 1, 2011

Characteristics Analysis of a Bastnaesite Rare Earth Mineral for Recovery of Cerium

Sep 13, 2010

By H. Hitchen

THE PURPOSE of this paper is to indicate the working capacity of different types of ropes for various engineering and mining duties. ROPE CONSTRUCTIONS There are approximately one hundred different designs of ropes in use today but, normally, only about ten are necessary for mining and engineering duties. The rest are designed for unusual equipments, or are different ways of combining wires of special shapes. Basically, the various designs of mining ropes consist of round, triangular, and oval strands, constructed with one or several layers of wire over a single wire, or a compound construction of sever.al wires. To suit different installations ropes are made with 3, 4, 5, or more of these types of strands over a central core, the ?co re itself being manufactured from either a fibrous material or a combination of steel wires. Nevertheless, in mining, the demand for 'locked coil rope', wl1ich may be considered as a single strand, is steadily increasing, especially for use on vertical shaft winding engines. So far as the locked coil rope is concerned, many constructions have been developed to suit different requirements, such as - in addition to winding ropes - aerial carrying Topes, shaft guide ropes and haulage ropes.

Jan 1, 1957

By J. W. Wang

This article first explains the mechanism of forming strength in the Jet grouting reinforced foundation, and points out the function of cement hydrates and clay minerals in clayey soil, the reinforced body with the character of long-term growth of strength. Secondly, regarding the strength and the deformation characteristics of compound foundation, the article points out that the stress-strain curve of the jet grouting pile is approximate to hyperbolic curve. Finally, the article cites three examples of application in the construction of the metallurgical industry.

Jan 1, 2010

By G. P. Hand

The purpose of this paper is to bring to your attention the various kinds of high performance graphites available today, their characteristics and possible applications. These materials are products of a proprietary high temperature technology developed by Superior Graphite Company. We feel we have only begun to tap the potential of this technology and the utilization of the resulting products. During the course of the paper, we shall investigate high purity, high performance graphites made from raw materials such as mined natural graphites, synthetic graphites and petroleum derivatives. We shall define their characteristics and resulting benefits to current applications, along with applications currently under development. It is our desire to stimulate speculation and development of current high performance graphites and their applications as well as ideas for new high performance products and applications. First, a little background about the process. The technology was developed through a concentrated R&D effort which culminated in 1976 in the construction of a unique furnace capable of continuously processing tonnage quantities of granular carbons at temperatures in excess of 2,500 degrees C. This process is capable of refining various carbonaceous raw materials, including natural graphites, to levels of purity and consistency that were previously unattainable in commercial quantities. Carbon contents in excess of 99.9% are currently being produced on a continuous flow-through basis. Since beginning operation in 1977, this plant, located in Hopkinsville, KY, has been expanded in stages to its present capacity of producing over 45,000 tons of purified graphites and graphitic carbons per year. In addition to the purification process, the technology used allows the introduction of selected elements into the carbon/graphite structure to provide additional benefits. Elements of interest include boron, silicon, copper, iron and rare earths. The characteristics of and applications for some of these products will be discussed later.

Jan 1, 1990

By Cheng Xie, Zhihu Li, Xiaoming Sun, Linsen He, Jiaxu Ding, Jinkun Yang, Yong Zhang, Zhenmin Qi

To solve the problem of large deformation of deep soft rock roadway, taking the soft rock roadway of no. 1 coal mine in New Shanghai as an engineering example, the deformation mechanism of surrounding rock of deep soft rock roadway is analyzed by combining theoretical analysis, numerical simulation and field test, and the control countermeasures centering on deep and shallow dense drilling are put forward. Through theoretical derivation, based on the masonry beam theory, surrounding rock structure S-R stability principle and composite beam principle, the length, angle, and spacing of deep and shallow dense drilling are determined. Through numerical simulation, the deformation evolution process of soft rock roadway surrounding rock after dense drilling pressure relief is reproduced, and the influence of drilling parameters (drilling spacing, dip angle) on pressure relief effect is analyzed and compared. The field application test and monitoring verify that the deformation control measures of deep and shallow dense drilling broken roof surrounding rock have a good effect of large deformation control of soft rock roadway, and provide a new support means for the safety and stability control of soft rock roadway.

Mar 2, 2024

By Dong-sheng Li, Hong-ming Long, Tie-jun Chun, Chao Ning, Zhen Wang

Iron ore sintering is an essential process in modern iron and steel production. It has the largest emission of the PM (particulate matter) in the iron and steel industry, accounting for about 40% of the total emission. The physical and chemical properties of PM 10 and PM 2.5 in the iron ore sintering were introduced, and the research development of PM emission reduction was also summarized. The potential future development of PM emission reduction by chemical agglomeration and capture in the iron ore sintering process was also carried out. The interface chemistry relationships between PM and polymer, such as sodium carboxy methyl cellulose (CMC) and polyacrylamide (PAM), in agglomerates were also investi- gated in this paper. It is signi ficant to reveal the characteristics of PM and develop the emission reduction technology of PM for the cleaner production of iron ore sintering.

Mar 1, 2018

By Wooltorton B

Highwall failures in surface coal mines in Queensland occur as circular slips through weak and weathered material, or as bilinear slides on sub-horizontal surfaces and steeply dipping joints. Weak horizontal planes occur in the Permian-Tertiary unconformity or on bedding surfaces within the Permian Coal Measures. Sub-vertical movements occur along rock joints and tension cracks induced by stress relaxation after excavation. Blasting also introduces new fractures and causes movement along existing rock discontinuities. Critical factors for stability include the dip direction of potential failure surfaces, shear strength of the rocks, damage due to blasting prior to highwall excavation, groundwater conditions, the type and performance of clays on shear surfaces, and pit geometry.

Jan 1, 1981

By Willard L. Cumings, Benjamin L. Miller

(Glen Summit Meeting, June, 1911.) I. THE CAMAGUEY DEPOSITS. 1. Location. THE Camaguey brown iron-ore deposit covers the top of San Felipe hill, the nearest point of which lies 14 miles NW. of the city of Camaguey. While there are several low flat-topped hills in the vicinity covered with a more or less continuous mantle of brown iron-ore, the deposit of San Felipe hill is the only one of any size and importance, and the name "San Felipe district " is proposed for the region. The deposit extends in a NW-SE. direction for a distance of about 10 miles, with an average width of 5 miles. The location is shown in Fig. 1, a sketch-map of the eastern part of Cuba. Fig. 2 is a map of the San Felipe district. 2. Description. The district is mentioned by Spencer,1 who says: "The Cubitas iron-ore fields are situated from 12 to 15 miles north of Camaguey City, in the province of Camaguey Within an area measuring roughly 10 miles east and west and 4 miles north and south, there are several flat-topped mesas rising 300 to 400 ft. above the level of an almost featureless plain which extends for many miles in all directions except toward the north." With the exception of the discrepancy in his statements as to the distance from Camaguey and the area of the hill, which is over 50 sq. miles, his description is a very good one. Kemp 2 has the following to say of ores in Carnaguey Province * Geologist, Bethlehem Steel Co. + Professor of Geology, Lehigh University. 1 Bulletin No. 540, U. S. Geological Survey, p. 324 (1908). 2 The Iron Ore Resources of the World, printed by the Eleventh International Geological Congress, vol. ii., p. 795 (1910).

Mar 1, 1911