Search Documents

By C Bellia, A Maldonado, S Strong, H Baxter

This paper discusses the technical and cost benefits of alternative data collection techniques used to collect lithological information, obtain laboratory testing samples and perform in situ testing. A comparison between diamond coring and sonic coring techniques is made using data from a recent geotechnical investigation for a final pit slope cut-back. The impacts of the coring method on laboratory strength testing results, material character testing and, ultimately, the mass strength parameters and subsequent slope design adopted are compared. The sonic coring method was chosen out of necessity and enabled the collection of tube samples of a clay unit of interest as well as bulk samples for material character and geochemical testing. The sonic coring generated unexpected degradation of clastic units, while cohesive clay-dominated units were recovered well. The likelihood that disturbance due to the coring method would result in lower than expected triaxial strength results was recognised ahead of time, with surplus samples collected and single-stage triaxial strength testing undertaken. This testing compared favourably with historic three-stage testing, where sample degradation occurred during the later stages. Material character testing of fine-grained, clay-dominated units was comparable with historic diamond core testing, while grain size estimates for more clastic units tended to be finer than previous results. The use of sonic coring over non-cored methods enabled the collection of material texture data, geotechnical properties and a full suite of geochemical analyses. This provided a comprehensive understanding of the lithological and geotechnical character of the rock and soil mass. A high-confidence geotechnical model was developed. The end result was the development of a slope design that was more aggressive than was previously designed (5° steeper inter-ramp angle), which has proven to be appropriate to the conditions following excavation. Overall, sonic coring was a cost-effective means of obtaining additional geotechnical data for the site.CITATION:Baxter, H, Bellia, C, Maldonado, A and Strong, S, 2015. Case study assessing alternative data collection techniques and analysis methods to assist with geotechnical slope design, in Proceedings Iron Ore 2015, pp 419–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By G B. Smith

Barrick (Australia Pacific) Limited initiated a trial of Caterpillar’s Minegem autonomous loader technology in 2009 at the Kanowna Belle mine in Kalgoorlie. Autonomous loader technology offers the potential to improve loader productivity, reduce operating costs and improve safety through removing personnel from the mine operating environment. This paper discusses the implementation of the technology at the mine site, the data collected during the trial and quantifies the benefits of using automated loader technology in comparison with teleremote loader operation. The lessons learned from the trial and work planned for the future in respect of this technology is also discussed.

Mar 21, 2011

By R. M. Owens, J. F. Lupo

The Shirley Basin Uranium mine, located in southeastern Wyoming, USA, was an open pit mining operation consisting of a series of several open pit mines excavated into poorly consolidated sandstones, siltstones, and claystones. Since the initial open pits were developed in 1969, slope failures have plagued the mine and mining operations. These slope failures have persisted into the current mine reclamation period. When the mine was first developed, the open pit slopes were designed to range between 45 to 55 degrees. Numerous slope failures during mine development required the pit slopes to be redesigned with slopes as shallow as 26 degrees. At present, movements are occurring within the open pits on reclaimed slopes that are shallow as 12 degrees. Several detailed slope studies were conducted at the mine in the early 1970s. These studies, combined with more recent geotechnical investigations, provide a unique detailed history of pit slope failures on shallow slopes. This paper presents an evaluation of the slope failures at the Shirley Basin mine, highlighting important mechanisms causing slope failures on very shallow slopes. The evaluation demonstrates important key parameters for shallow slope design.

Jan 1, 2001

By Rodger C. Fry

Underground coal mining has been active within the East Mountain property since the mid 1950's. As a result, coal from two seams has been extracted within large areas allowing surface subsidence to occur. Monitoring of subsidence annually, began in 1981 using on the ground conventional monumentation, surveying and photogrammetric monitoring. The data collected has shown the time benefits of photogrammetry and the relationship between observed subsidence and the geometry of the mined out area below.

Jan 1, 1986

By Scott Chesman

Increased TBM performance is leading the way for resurgence in tunneling activity in NYC. Tunnels will be excavated in the same geologic formations as previously excavated D&B tunnels whose construction records are providing valuable insight into the prediction of rock mass behavior. This report compares an eight mile stretch of NYC Water Tunnel #2 with the recently excavated eleven mile stretch of the TBM driven Water Tunnel #3. Comparisons of the type and amount of rock support installed as well as water inflows and grout quantities are made. Rock mass characteristics specific to TBM performance are also evaluated.

Jan 1, 2005

By D. C. Brady

"Within six months from award of a project management contract, Les Mines Dumagami Limitée, Cadillac, Quebec, was operating its new hoisting facility. This was accomplished with less than a six-week shutdown of mine production while still maintaining shaft access for underground maintenance.The work involved installing a refurbished /3.5 ft diameter double drum hoist, replacing a timber headframe with a newsteel headframe, increasing the ore bin capacity from 500tons to 1000 tons, constructing a new substation, and upgrading related facilities.This paper describes the work and methods used by various contractors, Les Mines Dumagami Limitée and J.S. Redpath Mining Consultants Limited to bring this project to a successful completion. It discusses the history of the project from proposal stage through to the design, procurement, scheduling, and construction management. The paper also comments on problems that were encountered and the methods used to overcome them.IntroductionThe Donald J. Laronde Mine of Les Mines Dumagami Limitée (Dumagarni), a gold and copper producer, is located in northwestern Quebec, approximately half way between Val d'Or and Rouyn. The mine started production in the spring of 1988 and the first gold bar was poured in June 1988.Following a request by Dumagami, on February 22, 1989, J.S. Redpath Mining Consultants Limited(Redpath) delivered a proposal to increase hoisting capabilities from 1500 tpd to a minimum of 2500tpd. Although various concepts were considered, Redpath proposed a new hoist house along the same shaft axis as the existing hoist, and located on the site of the existing substation. They would then provide a new substation, replace the headframe with a largersteel structure , gain extra storage capacities by increasing the bin heights, and raising the roof of the bin house accordingly.Although underground mining would have to be stopped for a month, the mill production would be maintained by feed from Dumagami's open pit.Figure 1 shows the original plant layout and Figure 2 represents the general arrangement after the project was completed . Table 1 compares the original hoisting facilities to the new facilities.On March 2, Dumagami awarded Redpath a contract that included preliminary engineering, detailed engineering, procurement and contract administration, and later added construction management. The preliminary engineering refined the initialconcept, selected major equipment, and prepared schedules and capital cost estimates for the total project."

Jan 1, 1991

By B. T. Lusk, J. M. Hoffman, J. Silva Castro

Blast vibration induces sounds within neighboring residences. A housewide vibration and sound monitoring system was installed in a West Virginia home subjected to blasts from various distances and directions. Eighty-nine blast events were monitored and analyzed. Fifteen channels of data were collected, including data from three triaxial geophones, one airblast microphone, one uniaxial geophone mounted on the wall of the house (response channel) and four microphones that recorded CD-quality sound waves inside the house. Each of these channels was recorded on the same time scale. The response channel signal was easily separated into ground vibration and airblast-induced movement, due to differences in the time of arrival. This response channel was then compared to the sounds recorded to determine which component of blast vibration induced the maximum sound response. Blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast, while for blasts beyond 762 meters (2,500 feet), the maximum sound response was caused by ground vibration without exception. When airblast was identified as the dominant sound generator, the peak amplitude of the sound was directly related to the amplitude of airblast. When ground vibration was identified as the dominant sound generator, the peak amplitude of sound was not related to the amplitude of ground vibration. Findings from frequency analysis showed that the frequency content of sounds inside the house was not related to the frequency content of airblast or ground vibration, regardless of source. This finding suggests that residents will have difficulty determining the source of blast-induced noise in their homes. The proposed airblast response factor (ABRF) can aid blasting operations to determine the dominant source of sounds inside a complainant’s house based on the time-of-arrival relationships. With this site-specific information, public relations responses can be developed accordingly.

Jan 1, 2010

By Liane J. Terrill

A 9O) ft (275 meter) section of a highly fractured beam of halite was mined from the roof of a supported thirteen year old drift at the Waste Isolation Pilot Plant (WIPP). The operation was conducted with a continuous miner and allowed the unique opportunity to collect spatial information on roof beam geology and to observe ground support conditions during the mining advance. Photographs and fracture maps of the mining face document the progress of the operation and the deteriorated condition of the strata. This case study details the drift's excavation and support sequences. the geomechanical response, and the conditions found in the exposed roof beam.

Jan 1, 1997

By Chandrasegaran, Tamilmani

"This paper describes a case study of a retaining wall structure using a diaphragm wall to construct a stilling basin at Tanjung Bin T4 power plant in Johor Bahru, Malaysia. The stilling basin is part of the Phase IV (T4) 1x1000MW power plant’s offshore cooling water discharge culverts. The site is located close to the sea with 5m of fill on top of very soft sediments of marine origin up to 20m thick underlain by fluvial clay and metasedimentary rock. Stringent wall deflection criteria and construction program dictated adopting an efficient solution with 800mm thick diaphragm wall supported by permanent top support as the temporary prop and improved horizontal restraint provided by deep mix piles acting as a slab (ground improvement layer) below the final excavation level. The depth of excavation is about 10.12m from the existing ground level. The proposed solution kept the wall deflection below the limit of 0.7% of the depth of bulk excavation and avoided additional props leading to faster completion of the structure. With unsymmetrical loading behind the retaining walls, 2D finite element analysis was carried out to assess the wall deflection and stresses in the wall and the grout layer below. The diaphragm wall is instrumented to monitor the behavior and the findings are discussed in the paper.INTRODUCTIONConstruction in soft marine clay has always been a challenge to the engineer because of its very low shear strength and its sensitivity to disturbance. In the case of excavation projects the problem becomes even more complicated with development of excess pore pressure during excavation. Marine clay with its low shear strength and lesser passive resistance, generally leads to large wall movements and settlement behind the wall. Increased passive resistance coming from increased number of props is useful but has its limits and it is no longer the most effective way in containing or reducing the wall movements or forces in the wall. One of the solutions to these problems is to improve the soil shear strength by means of ground improvement infront of the wall at an elevation most appropriate to maximize wall performance. There are several methods adopted in improving a soil layer including mixing additives to the ground to improve the shear strength to partially replacing the weak soil while others are fully replacing the weak soil. This paper discusses the case study of approximately 10m of excavation in soft marine clay using 800mm thick diaphragm wall supported by Deep Mix Piles (DMP) being used to improve soft marine deposit to form a slab just below the formation level and thus improving passive resistance significantly. The ground improvement layer helped to reduce the wall forces and deflections making it possible to remove the need for additional temporary props leading to significant savings is time and productivity. The paper presents the various options explored before this method is adopted, the design approach, instrumentation data and the monitored results."

Jan 1, 2015

By M. V. T. Da Silva, J. C. Harrison

Eldorado Gold Corporation of Vancouver, B.C. owns and operates three gold mines. The São Bento underground gold mine in Minas Gerais State, Brazil produced 105,907 ounces in1997. The La Colorada and La Trinidad open pit, heap leach mines in Mexico produced over 83,000ounces in 1997. With a deteriorating gold market plaguing the industry throughout 1997 Eldorado had to take critical measures at each mine to enhance gold production while lowering cash operating costs. Each mine had its own unique problems to confront. This case study will discuss three distinct courses of action taken at the three mine sites.

Jan 1, 1999

By R. J. Matetic

Mining operations have long been accused of causing a disruption to local, domestic and agricultural water supplies. More recently, concern for water supplies has increased with the advent of high-extraction mining techniques, namely longwall mining. Theoretically, any water bearing zone in the overburden above a high-extraction mining operation may be affected by mining. In some cases, a confining bed may be fractured causing a loss of water to a particular zone. In other cases, increased fracture permeability may enhance the ability of an aquifer to transmit and deliver water. Unfortunately, only a limited amount of studies have been conducted that characterize hydrologic changes and also quant1fythe magnitude of mining-induced subsidence. The U.S. Bureau of Mines conducted such a study at a mine site located in Greene County, PA. A total of 8 water wells were drilled and hydrologic parameters such as specific capacity, transmissivity and well yield were determined both before and after mining. Electronic water level recorders were installed on each water well to provide continuous observations of water level fluctuations.

Jan 1, 1990

By Warder A. Shaver

INTRODUCTION Mine No. 95 of the Consolidation Coal Co., a divi¬sion of Continental Oil Co., is located in Shinnston, WV. Mine No. 95 was opened in January 1967 and has been operating continuously since that time. The mine has 544 hourly and salaried employees. In 1974 this mine was the largest coal producer in West Virginia. Opera¬tions include two longwall sections and eight Marietta Borer continuous miners. Originally there were also two Jeffrey Heliminer continuous miners, but use of these was discontinued in June 1978. Production averages 12 727 t/d (14,000 stpd). Two portals now service the mine with a third portal proposed for 1978. GEOLOGY Mining takes place in the Pittsburgh coal seam which dips 0.04 rad (21h°) northwest. The working seam is steam coal with an average height of 2.2 m (86 in.). Immediately above the seam, the overburden is com¬posed of 6.1 m (20 ft) of shales followed by 6.1 m (20 ft) of weak sandstone and 51.8 (170 ft) of shaley limestone. The shale weathers when exposed to mois¬ture. Surface water has been a problem due to a fire¬clay floor which turns to paste when mixed with water. GENERAL DESCRIPTION The present mining plan for Consol's No. 95 mine has a proposed life of 35 to 40 years. One set of main headings has been driven in the north direction and one set in a western direction. These are the areas in which the majority of the virgin coal lies. The panels are driven off of the mains at 2134 to 3048-m (7,000 to 10,000-ft) intervals. The continuous mining sections are set up 133 x 610 m (600 x 2000 ft). Longwall sections are 259 x 1220 m (850 x 7000 ft). All of these mining sections are retreating uphill. Development is with continuous miners. A Marietta Borer miner is used for the main development work. These miners cut 4.1 m (13 ft 6 in.) wide and 2.1 m (7 ft) high, leaving an arch cut. Along with the arch, a 152.4-mm (6-in.) thick layer of roof coal is left in place to protect the roof from weathering. The combi¬nation of the self-supporting arch and the roof coal al¬lows the entries to be driven 30.5 m (100 ft) without bolting. Full bolting, however, is carried outby the last open crosscut. This bolting is done on 1.5 x 1.5-m (5 x 5-ft) centers using 1.5-m (5-ft) long roof bolts with tandem anchors and 152.4-mm (6-in.) steel washer plates. When needed, crib blocks with a 50.4-mm (2-in.) drill hole are used as supplemental supports. Three-hole steel channel with the ends curved down¬ward to conform to the borer arch may also be used. In the mining sections, a 14 BU loader is used be¬hind the Marietta miner to load two Torkar shuttle cars. These haul to Long-Airdox feeder breakers which load onto a 1.07-m (42-in.) wide conveyor belt. With the exception of the shuttle cars, which use 275-V d-c power, the face equipment operates on 550-V a-c power. The main power line is 7200 V ac. The same loading and hauling equipment is used with the Marietta Borer miner for driving both panel and development entries. In the retreat sections, the same equipment with the exception of the miner is utilized. Because of the advantage of a variable cutting hight, Jeffrey Heliminer ripper-type continuous miners were employed in these retreat sections. For longwall mining the first unit uses an Eickoff EDW 300-L double-drum ranging shearer. Drum di¬ameter is 1.69 m (66 in.) with a drum rotation speed of 45 rpm. The drum is equipped with 48 Carmet 34-L-1 bits. The 300-kW (400-hp) motor operates on 1000 V. Tramming of the shearer head is done through a hydraulically driven 26-mm wide chain. Maximum cutting speed is 7.93 m/min (26 fpm), and maximum tram speed is 12.8 m/min (42 fpm) with an average cutting speed of 3.66 m/min (12 fpm). Web cutting depth is 762 mm (30 in.) and the cutting height is 2.13 m (7 ft). The conveyor width is 686 mm (27 in.). It uses a single chain, 26 mm thick, with flights on 0.91-m (3-ft) spacing. The face conveyor speed is 64.3 m/min (211 fpm) when driven by two 112-kW (150-hp) 1000-V Louis Allis motors through torque convertors. The roof support used is Gullick Dobson chocks [6-legged 77.3 t (85 st) per leg, 463.6 t (510 st) total capacity] with double-acting leg jacks. The hydraulic pressure for the legs is 13.8 MPa (2000 psi), and the hydraulic pressure for rams is 6.8 MPa (1000 psi). The yield valves are set at 57.8 MPa (8500 psi). Each chock weighs 4.09 t (4.5 st). The stage loader is an Eickoff drive, with a 68-kW (90-hp), (00-V Reliance motor. A 26-mm thick single strand chain with flights on 0.6-m (2-ft) centers runs at 75.89 m/min (249 fpm). The stage loader is self-advancing and is connected to the belt tail piece with a special fifth wheel attachment so that the stage loader can advance and guide the tail piece. The hydraulic pressure for the roof support is supplied by two 45-kW (60-hp) Reliance motors op¬erating on 699 V, with 1.26 L/s (20 gpm) constant volume Gullick hydraulic pumps. Each pump services alternate chocks, with the two pressure lines connected at the tailgate by 25.4-mm (1-in.) hydraulic hoses, rated at 27.21 MPa (4000 psi). The 6.8 MPa (1000 psi) pressure rams advance is supplied by a 45-kW (60-hp), 600-V Reliance motor and a 1.26-L/s (20-gpm) con¬stant volume Gullick pump. Return lines are 35.5-mm (1.4-in.) diam hydraulic hoses with rated capacity of 27.21 MPa (4000 psi). The fluid used in the hydraulic system consists of 95% water and 5% Hy-chock fire resistant water soluble oil. Water is stored and mixed in a 6096-L (2000-gal) track-mounted tank and goes to a 655-L (180-gal) reservoir at the pump. The belt conveyor structure is 1.07 m (42 in.) wide with 0.47 rad (27°) idlers, bottom stands located on 3.05-m (10-ft) centers, top stands on 1.5-m (5-ft) centers, and is supported on a 19-mm (3/4-in.) diam

Jan 1, 1982

By H. Cay, J. Zachwieja, T. Esplin, R. Ravenelle, T. Olsen-Tank

Barrick Goldstrike mine utilizes a carbon-in-leach (CIL) circuit to simultaneously leach gold into solution with cyanide and adsorb the gold-cyanide complex onto activated carbon for further refinement. If the gold bearing ore contains a significant amount of native carbonaceous material, gold cyanide can be adsorbed at these sites instead of onto the desired activated carbon and the gold is effectively lost to tailings in a detrimental process known as "preg-robbing." The preg-rob effect is considerably reduced by treating the ore with a surfactant, which is hypothesized to adsorb to and passivate the native carbon surfaces. Past laboratory and pilot studies have consistently demonstrated significant gains in gold recovery after treating carbonaceous ore with surfactant. With success in bench and pilot scale testing, a plant trial was conducted at Barrick Goldstrike to evaluate the feasibility of using an alkoxylated fatty amine surfactant (Ethomeen T/12) to aid in the leaching of high preg-robbing ores. This paper analyzes the performance of the surfactant during the plant trial in addition to the problems that occurred during the trial period. Suggestions for improvement are also discussed.

Jan 1, 2014

By S. F. Smith

Following a roof beam collapse on a major production district at the British Steel Corporation's Dragonby Iron Ore Mine, Scunthorpe, South Humberside, UK, rock mechanics investigations were undertaken in this room and pillar operation to assess the stability of workings throughout all the underground mine area. Over a four year period room convergence and roof sag were monitored in different mining areas and various junction configurations in order to assess and compare the relative movement of the strata resulting from mining activities, where varying rock bolt lengths and patterns have been utilised. The paper, after shortly describing geological aspects and mining methods, presents the research procedure adopted together with the instrumentation employed and discusses the results obtained during these investigations.

Jan 1, 1995

By Fernando O. L. Xavier

"The Barro Branco coal mine was located in the southern region of Brazil, in the state of Santa Catarina. In 2002, an incident occurred at the mine, leading to a violent, massive pillar failure, resulting in almost 100 failed pillars in less than 3 hours, totaling nearly 700 collapsed pillars after a period of 6 weeks. The paper outlines the geological and operational conditions before the accident and analyzes the primary factors leading up to the event. This paper also discusses and examines the unusual characteristic of violent, uncontrolled pillar bursts that occur over a longer timespan, in comparison to other equally violent but rapid events, such as those that occurred at the Crandall Canyon Mine, at a Book Cliffs District mine, and at the Solvay Mine. INTRODUCTION The southern region of Brazil holds 100% of the coal reserves for the country, and half of it is located within the state of Santa Catarina. Almost the entire Brazil’s coal production, around 8 million tonnes/year, is consumed for electricity generation. Most of the coal mines in Santa Catarina are underground room-and-pillar mines, and most are shallow mines, with depths of cover ranging from 20 to 400 m. The Barro Branco mine, near the city of Criciuma, experienced a violent mine collapse at the end of March 2003, which was analyzed and discussed by Zingano, Koppe, and Costa (2004). The event consisted of violent failure of 100 pillars in less than 3 hours, and a subsequent failure of approximately 700 additional pillars over the next 6 weeks. After the panel collapsed, the mine was closed due to unsafe conditions as a consequence of the seismic event. A map of the collapsed area is shown in Figure 1. GEOLOGY AND MINING METHOD There are two coal seams mined at Barro Branco mine. The first is the 1.5 m to 2.3 m thick Barro Branco Seam, under about 75 m of cover. The second is the Bonito Seam, where the collapse occurred. The Bonito Seam is 2.5 to 5.5 m thick located at a depth of approximately 80 m, with an average dip of 0° to 15°. Various major faults and inherent joints are present in the area."

Jan 1, 2017

By Mark A. Krall

The Conda Partnership's Dry Valley Phosphate mine is a thinly bedded, multiple seam, open pit mining operation where selective mining techniques are used to recover phosphatic shales. The mining methods used are truck/shovel and scraper/ dozer operations. The ore that is mined is shipped 32 km (20 miles) by rail to a beneficiation facility which upgrades the ore via washing and calcining. The mine and beneficiation complexes are owned by the Conda Partnership. The Conda Partnership is a joint venture between Beker Industries Corp. of Greenwich, Connecticut, and Western Co-Operative Fertilizers (U.S.) Inc. of Alberta, Canada. The Conda Partnership operates as a separate entity from the two partners.

Jan 1, 1984

By Chris T. Franke

The Waste Isolation Pilot Plant is a deep underground facility mined in bedded salt interspersed with persistent clay inter- beds. The clay seams delineate beams of salt above and below the excavations which strongly influence excavation performance. This paper reviews available rock mechanics information relevant to improving drift stability by removing the roof beam. Conceptual deformation mechanisms, relevant field data, and numerical analyses were used to investigate the effects of mining the roof of the excavations along a clay seam. Finally, a case study that applies the results of this investigation is presented.

Jan 1, 1997

By R. Hart

In this paper, problems that have been experienced with the rockpass system at Kloof Mine No. 3 Shaft are described. Actions that have been taken to overcome the problems are also described. These include the use of slugshots to remove hang-ups, the abandonment and waste filling of passes, and design criteria adopted for an alternative pass system.

Jan 1, 2006

By Jérôme Girard, Shiu Kam, Sue Longo

"Historically, tailings management in a northern climate has involved the deposition of tailings into the Tailings Management Area (TMA) as conventional slurry. This type of system is obviously viable but presents challenges that are difficult to manage as circumstances change over the life of mine. These issues can include:? Increases in mill throughput, and? Life of the TMA for the life of mine.This case study will present how thickened, high-density, non-segregating tailings are used as an alternative to conventional slurry disposal to achieve greater storage capacity and enhanced environmental performance for a gold tailings facility in a northern climate. This paper will focus on how this change in deposition strategy accommodated the increased throughput of the mill and the increased life of mine. Specifically, the paper will discuss the addition and integration of new processes to the exiting mill system to accommodate the tailings management issues. It will highlight the challenges from laboratory testing to pre-feasibility to the engineered design of the thickened tailings system implemented at Musselwhite Mine.BACKGROUNDGoldcorp Canada’s Musselwhite Mine, in Northwestern Ontario (120 km north of Pickle Lake), is an underground gold mining operation that began production in 1997. The current mill throughput is about 4000 tpd (1.4 Mtpa). Gold extraction is based on a CIP process with cyanide destruction.The existing tailings management area (TMA) is located about 2 km southwest of the mill complex. The TMA is contained by high ground to the north and to the west and flanged by a moraine ridge along the south side. A number of dams have been constructed along this ridge. The dams were first built in 1996 and subsequently raised in 2000 and again in 2005. Excess tailings pond water is discharged to a polishing pond then released to the environment via a wetland.The TMA was originally designed to contain 13.7 Mt of tailings under a ponded surface for closure. The water cover was to inhibit adverse long-term environmental effects because the tailings contain pyrrhotite and other sulphide-bearing minerals that are potentially acid generating. The design was modified during Stage 3 Construction in 2005 to expand the storage capacity to 17.3 Mt (Golder, 2005). As of end of 2009, over 16 Mt of tailings had been deposited in the TMA. The slurried tailings were historically deposited at 50% solids."

Jan 1, 2011

By Chris A. Bennett, Glenn S. Dobby, David A. Bulled

Establishing reagent dosing strategies for new ore bodies has traditionally involved a combination of experience and empirical experimentation using standard laboratory tests. The grade and recovery data resulting from these lab tests have historically been used as direct indicators of plant performance despite the obvious differences between the flotation environments. A reagent scheme selected in this way would subsequently be employed to generate the grade and recovery information for the geometallurgical model which in turn was used for metal production and cash flow forecasts. If the reagent scheme was sub-optimal then so too would be the forecasts and the resulting cash flow.

Jan 1, 2003