Search Documents

By Julius Pohlman

The history of Niagara Falls, as currently told, is simple, and by that very simplicity it has been rendered plausible. AS the story runs, the Falls were once situated at Lewiston, 7 miles to the north of their present site; and, since all the rocks in this section are alternate hard and soft strata, the waters acting readily upon the soft shales caused their removal, and the overlying hard lagers, deprived of support, broke down under the weight of the large volume of water that rushed over them; and this erosive action has sent the edge of the fall more and more southward, until it now has excavated the seven-mile gorge between Lewiston and the village of Niagara Falls. (See Fig. 1.) As early as 1790" we find this theory advanced in a description of this region; and it has been practically endorsed by subsequent observers, the most prominent of whom was Prof. James Hall, the State Geologist of New York, who surveyed the Falls in 1841, and gave the most exact description of their surroundings in the publications of the State Survey.? Not until 1883 was the correctness of the accepted theory of the Falls questioned.‡ The geology of the basins of the Great. Lakes, as elucidated by Newberry,§ Speneer,ll and others, has added largely to a clearer understanding of the life-history of the Falls. The investigators have shown us that Lake Erie, as a lake, is, geologically speaking, quite young; that its valley was excavated in pre-glacial times by a series of rivers; and that the Maumee, Sandusky, Cuyaboga, Alleghany and other rivers carried the drainage of the surrounding

Jan 1, 1889

By H. S. Munroe

The dressing-works of the St. Joseph Lead Company were destroyed by fire, February 26th, 1883. Within about four months, or on July 5th, 1883, the new mill, with a capacity of 500 tons per day, was built and in active operation. The capacity of the new mill has since been increased to 800 tons per day. The old mill was built in 1867, by Mr. C. B. Parsons, the present superintendent. It was a curious rambling old structure, which had grown with the demands of the business; a few jigs having been added in one place, a table or two in another and wings and sheds added to the main buildings, from time to time, as it was found necessary to increase the efficiency or the capacity of the mill. The old mill was, moreover, a most interesting place to the student, a perfect "museum of ore-dressing." Nearly every form of dressing apparatus known to the art had, at one time or another, found a place under its roof, jigs of many kinds, concave, convex, side-bump and stationary tables, tyes, buddles, dolly-tubs, etc., etc. The method of dressing followed in the main the lines of English practice, but with many modifications, both in the machinery and the methods of working, due to the inventive genius of Mr. Parsons. Different forms of crushing apparatus were tried, and the best method of handling the ore and the different products of

Jan 1, 1889

By William R. Webster

This is a subject which our Institute has made peculiarly its own. In the first volume of its Transactions the analysis of steel received attention, and every subsequent volume has borne witness to the acuteness and industry of our members in the investigation of this subject. The keynote mas struck, in this as in so many other lines of progress, by A. L. Holley, in his paper on " Tests of Steel," read at the Easton meeting of October, 1873 (Trans., ii., 116)—an essay which may rank as a classic by reason of .its elegant form, logical force, and clear prevision of all the bearings of its theme, Taken together with the brief report of the discussion which followed it (in which Dr. Drown emphasized the effects of heat-treatment and mechanical handling, and Dr. Sterry Hunt the importance of minute variations in chemical composition, and of possible isomeric and allotropic conditions), it constitutes, after the lapse of twenty-five years, an admirable and adequate introduction to the long list of technical papers which have succeeded it. Three years later came the epoch-making papers of Dr. C. B. Dudley on the relation between the chemical composition and physical properties of steel rails, which, with the voluminous discussion they evoked, constitute a special volume, published by the Institute, and full of useful suggestions. If Dr. Dudley could be induced to resume this investigation, he would doubtless be able to solve many points still uncertain or disputed. But I cannot undertake to review the history of this subject, as represented in our Transactions—still less to restate all the contributions to it which have been made in books or in papers before other technical societies, since the initiative was taken by the Institute. My more modest purpose is to indi-

Jan 1, 1899

By F. E. Bachman

Although it has been apparent to me for a long time that too great weight was currently given to the silicon-contents of foundry-iron, and that the theory of the control by silicon of the carbon-contents of cast-iron is unsound, or that, at best, the influence of silicon is too small to be of much practical value as a guide in foundry-work, it never seemed to me desirable to enter the lists against either the " silicon-fad " or the theory, for the reason that I had neither the time nor the facilities to prove my position, nor any better theory to offer. But since Mr. Summers has taken the step, it seems but right that I should give such facts as are at hand in support of his contention. At the same time I do not think these are enough to prove the case if the contrary proposition were not itself, as it seems to me, based on insufficient evidence. Both Keep's and Turner's conclusions seem to be drawn from irons carrying less than the normal amount of carbon; Turner's " base " being, moreover, a steel rather than a pig-iron, and both the white base and the ferro-silicon of Keep being so low in carbon that compounds of them would not give a material approaching the carbon-contents of a normal casting, and having, therefore, little value as showing the effects of silicon on foundry-irons, even if his samples were treated under the same conditions as those to which pig-metal is subjected in making castings.

Jan 1, 1899

By Robert D. Deister

The Buick Concentrator represents state-of- the-art technology in automated digital process control operation utilizing a centralized computer. The process control strategies implemented at Buick are no longer new to the industry but the successful application of these developments is still rather unique in North America. Productivity improvements, determined to be a direct result of the process control developments, are the primary topics of this paper. Emphasis is placed on metallurgical benefits including both lead and zinc recoveries, lead concentrate grade and reductions realized in reagent consumptions, operating costs and personnel. The productivity improvement discussion is preceded by a concentrator description and a brief history of the process control development at Buick. Current control strategies and future applications are presented afterward.

Jan 1, 1985

By Mikko Loponen

Outotec has developed an operator training simulator (OTS) platformsuitable for various hydrometallurgical processes. The complete solution is run in the cloud, where virtual client instances can be managed on-demand. The aim is to build a generalizable model that produces coherent results even when operating outside of ideal parameters, allowing the operator to train in unsteady state conditions such as start-up and shutdown. Complex software products are commonly associated with significant development time and cost. Utilizing modular software architecture, only the control system and processmodel are tailored for theOTS,whereas modules such as user administration and cloud-based client machine spawning can be imported, shortening development time. A generic acidic pressure oxidation process (POX) operator training simulation consisting of feed preparation, autoclave, dual-stage flash evaporation and off-gas scrubbing is described. Process is simulated using Outotec HSC Sim 9 process simulator and controlled by Siemens Simatic PCS7 control system.

By L. A. Cornish, S. N. Prins, R. Süss

The work is being done using the Thermo-CalcTM software, and the database is being built up by obtaining good thermodynamic descriptions of all of the possible phases in the system. The database supplied did not cover all of the phases, and these had to be gleaned from literature, or modelled using experimental data. Similarly, not all of the experimental data were known, and where there were gaps or inconsistencies, experiments had to be undertaken. A preliminary version of the database was constructed from assessed thermodynamic data-sets for the binary systems only. The binary descriptions were combined allowing extrapolation into the ternary systems, and experimental phase equilibrium data were compared with calculated results. Very good agreement was obtained for the Pt-Al-Ru and Pt-Cr-Ru systems, which was encouraging and confirmed that the higher-order systems could be calculated from the binary systems with confidence. Since some of the phase models in databases were different, these phases had to be remodelled. However, more work is ongoing for information concerning the ternary phases present in the Al-Cr-Ru, Pt-Al-Ru (two ternary compounds in each) and Pt-Al-Cr (possibly more than three ternary compounds) systems. At later stage of the work, problems with the thermodynamic descriptions of the Cr-Ru and Pt-Cr binary systems were found. A programme of experimental work to overcome these has been devised, and is being undertaken. Keywords: Pt-based alloys, phase diagram calculations.

Jan 1, 2006

By R Baumgartner

The Canahuire deposit is a recently discovered Au-Cu-Ag epithermal deposit in Southern Peru. A geometallurgy program is a key study element of the project Feasibility study. Metallurgical, mineralogical, and comminution studies have been completed over a suite of samples, spatially distributed among the various geological/ore domains. The early stage of Canahuire presents challenges as there is a lack of metallurgical information to guide geometallurgical sampling, in contrast with an established deposit at a more advanced stage of development or mining. Nevertheless, the available information will assist in the development of geometallurgical domains for Canahuire in order to ensure that future metallurgical, mineralogical, and comminution test work is representative of the deposit variability. This supplementary knowledge will be able to predict important metallurgical parameters which will be incorporated into a geometallurgical model to spatial predict material types, metallurgical recovery and through put. The information obtained will be a valuable addition to the future mine plan, influencing process design, engineering design, plant operation, operating and capital costs, and ultimately will reduce project development risk.

Sep 5, 2011

By Lori A. Simpson

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the three-level basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tied-back soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

By Lori A. Simpson, Linda H. Liang

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the threelevel basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tiedback soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

Jan 1, 2017

By Leon H. Bruner

This paper presents a case study describing how a global consumer products company with 138,000 employees that markets over 300 brands in 180 countries is building sustainability into the rhythm of its business. This strategy extends beyond social investment programs by incorporating sustainability into the fabric of product design, manufacturing operations, employee engagement and stakeholder partnerships. During the implementation of this program it has been necessary to be explicit about sustainability and its importance to the business, to broadly define sustainability, to ensure that sustainability is not added work, to eliminate trade-offs between performance, value and sustainability and to implement programs to ensure that sustainability is incorporated into the DNA of the company. Our program continually emphasizes the importance of making no tradeoffs between consumer acceptance of sustainable products and sustainability investments. We also work diligently to overcome the challenges of engaging employees around the world to implement a single coherent sustainability strategy that delivers great results.

Jan 1, 2010

By Tony Szwilski

Indonesia has enormous mineral resources. Its population of more than 180 million people inhabit most of the more than 13,000 islands. The country is becoming a significant economic power in Southeast Asia. Indonesia is the largest Muslim country in the world. Java, its largest island, is the most densely populated area. The country's diversity is its strength. However, as only an estimated 16 million inhabitants speak bahasa Indonesia as the first language, communication problems endure. Although burdened with large debts, Indonesia has been able to service the debts better than most developing nations. This has given it high credibility and, with increasing frequency, creditor nations compete to provide Indonesia loans with the most the most favorable financial terms. Recent rising prices of petroleum crude has further improved Indonesia's economic status. It maintains a policy of stable oil prices that it promotes in OPEC, of which it is an influential member. As a result, Indonesia is becoming increasingly attractive to foreign investors. The South East Consortium for International Development (SECID) is made up of 34 universities in the southeastern US and Indonesian partners Lembaga Afiliasi Penelitian dan Industri (LAPI) of the Institute of Technology in Bandung, West Java. SECID bid successfully against international competition to develop new academic programs and campus for the Sriwijaya University UNSRI) in Palembang, South Sumara. Funding for the project was provided by the government of Indonesia through a loan from the Asian Development Bank (ADB). There are 47 public universities

Jan 1, 1991

By John S. Civetta, Seth Martin, Marc J. Gallagher, Arthur J. Alzamora, Ronald Peralta

The Crown Building, built circa 1921, is a 26-story iconic building located at West 57th Street and Fifth Avenue in the heart of Manhattan. The paper highlights collaboration between the geotechnical engineer and foundation contractor to develop economical and practical solutions to foundation design and construction challenges associated with this complex redevelopment project. The project includes both below-grade and above-grade expansion of the occupied building, and required undermining the existing foundations, and essentially doubling the foundation loads. The below-grade expansion required surgical foundation work including drilling minicaissons, shoring columns, underpinning, and excavating 20 feet of rock.

By J. A. Flinn

Phelps Dodge’s Morenci copper mine has had six drills, six track-dozers, 16 shovels, two loaders, and 90 haul trucks equipped with either Caterpillar, Aquila, or Modular GPS systems for nearly three years. The Caterpillar Computer-Aided Earthmoving System is an open-architecture system, which allows for inputs to enhance orientation solutions and system functionality. This system has begun a new phase that leads to an intelligent mining system. Optimization techniques of the current system and inputs are reviewed. In addition, some practical issues of implementing new technology in a mining environment have been identified to aid in this new phase.

Jan 1, 2000

By I Thin, L Morizzi, C Seymour, G Mungur

Olympic Dam has been investigating mine design options for the South Mine Area (SMA), which will continue using the existing sublevel open stoping (SLOS) method. The SMA is an undeveloped mining area, located south of the existing underground mining areas currently in production at Olympic Dam. The SMA study reached the stage where geotechnical inputs were required for stope design, infrastructure location and ground support forecasts. A large database of geotechnical data was collected to inform open pit designs for the ODX (Olympic Dam expansion) project (resulting from 659 drill holes). This geotechnical data has since been reprocessed to align with design inputs required for the SLOS mining method. The result has been the construction of a preliminary three-dimensional mining rock mass model (MRMM) that has been incorporated into preliminary stope mine design and infrastructure layout assessments, which have taken into account the predicted prevailing ground conditions.As with any model, it is necessary to improve the confidence in its predictability; therefore the model must be calibrated. The preliminary SMA MRMM was no exception. First pass calibration was possible with results from underground geotechnical window mapping from exposed rock mass conditions in the lateral development and surface geotechnical holes for ventilation shafts.The SMA project continues to advance and has started a program of resource drilling. Selected holes have been identified that target data limited areas. This will ensure that the data gaps are infilled in order to maintain the required data density required to improve the model confidence. In addition, further underground window mapping in the SMA will provide ‘mine scale drill hole’ data that can be used to either update the MRMM or as part of planned future calibration. Stope performance data from stopes will provide further valuable data for calibration purposes.The proposed paper will present the process and findings that have been followed in order to establish a well calibrated geotechnical model that can be used with an acceptable level of confidence in the ongoing refinements of the mine design and planning process for the SMA.CITATION:Thin, I, Morizzi, L, Mungur, G and Seymour, C, 2016. Building and calibration of a geotechnical model for sublevel open stope design at Olympic Dam, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 523–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By T J. V Duffy, L H. D Siahaan, P G. Albert

G-ResourcesÆ Martabe Mine in North Sumatra, Indonesia, is a US$700 M world-class and world-scale operation in a country which, with a few notable smaller scale exceptions, has had no significant hard rock mining development in more than ten years.The mine was commissioned in the middle part of 2012 and poured first gold on 24 July. At full production Martabe will produce 250 000 oz/a of gold and 2 - 3 Moz/a of silver at cash costs in the lowest quartile. The mine location is on the west coast of North Sumatra, which experiences annual rainfall of 4 m with no notable dry season, adjacent to seismically active fault zones, and relatively close to a rural community of 31 000 people with no significant industrial experience.The management team has successfully forged strong links with the various government departments and levels in Jakarta, North Sumatra Province and the local Regencies; developed long-term relationships with the various community groups within the local district of Batangtoru to build a sustainable social licence; has dealt with the physical and environmental challenges presented by the project location, and has successfully raised more than US$900 M over a period of three years for the original acquisition then the development of the project.Whilst in its infancy of operation, the mine is set up to deliver a long-term sustainable future for the company, the shareholders, and the people of Batangtoru and all stakeholders generally. The quality of the project execution and commitment by the company will ensure that maximum value can be delivered from Martabe, not just for the current mine life but from the significant exploration potential that exists on the large tenement area that the company has access to for 30 plus years.This paper will deal with the physical challenges associated with the design, the Indonesian government regulatory requirements for mine development, the social aspects of building a world-class project in a developing area, the in-country commitment necessary for any project development anywhere in the world and the successful funding arrangements for the mine development.CITATION:Albert, P G, Siahaan, L H D and Duffy, T J V, 2012. Building AsiaÆs latest hard rock mine, in Proceedings International Mine Management 2012, pp 189-204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

The structural design of a mine haul road involves the determination of cover thickness requirements above the in-situ or sub-grade material. The specification of these layerworks is a critical component in the overall road design process. Poor design often leads to premature failure of the road, safety is often compromised and productivity and equipment service-life will certainly decrease. Historically, the California Bearing Ratio (CBR) cover-curve design method has been widely applied to the structural design of mine haul roads. More recently, established mechanistic design principles have superceded the CBR approach to haul road design, using a multi-layer model to represent the various road structural layers. The structural design and associated layer thickness requirements are then determined following a maximum strain criterion. This paper develops a case-study evaluation of the CBR cover-curve and mechanistic design methodologies and through a comparative analysis of layerworks and materials, highlights how improved structural design can be achieved mechanistically.

Jan 1, 2011

By Paul A. Filteau

Asbestos ranks among the leading minerals produced in Canada. It is also mined in Russia, Rhodesia, South Africa, Cyprus, Italy, the U.S.A., Japan, China and several other countries. The most abundant variety, chrysotile, and also the most valuable form of asbestos produced, makes up 90% of the world's supply. In Canada, chrysotile is found in the provinces of British Columbia, Ontario, Newfoundland as well as in Quebec, the latter accounting for almost 90% of all the fibre produced in this country. A number of developments emerging this year could make 1968 a record production and export year for Canada's asbestos mining industry. Asbestos fibre consumption in increasing in the U.S., Canada, up 10% to date this year, Japan and in Latin America. Demand in Western Europe is again on the upswing, following a cut-back last year. As a result, shipments from Canadian mines for the first eight months of this year reached some 916,968 tons versus 873,402 in 1967, an increase of 43,566 tons or 5%. Indications are that Canadian asbestos production will for the first time ever top 1.5 million tons in 1968.

Jan 1, 1969

By L. Bloom

In 1996, lack of confidence in assaying methods and sample handling affected companies as diverse as Bre-X and Timbuktu. Both share prices and the ability to raise financing are impacted when the quality of assay data is suspect. Overseas projects are subject to enhanced scrutiny when local facilities are used that are unfamiliar to brokers, financing agencies and banks. Quality control systems can be -implemented but there are associated costs. These costs should reflect the risk to the mining company, investors and financiers and the size of the proposed investment. In this regard, assay control call is considered a form of insurance to enhance the value of an exploration or mining project.

Jan 1, 1997

By Olivia Gamache

When working in remote and extreme environments, projects are faced with new challenges for engineering and project execution. This is heightened when also working in countries with a developing environmental regulatory framework, small skilled workforce available for recruitment, and minimal infrastructure such as power, roads, and water. There is an increasing realization that social and environmental aspects need to be built into project execution. Giving proper attention to these issues during project development and execution, and maximizing opportunities is an ongoing challenge.

May 1, 2013