Search Documents

By M. M. Rajkovich, L. Adams, J. J. Zaluski, S. Gardner

In 1998, Kentuckians for the Commonwealth filed an Administrative Petition with the Kentucky Natural Resources and Environmental Protection Cabinet to designate 8,903 +/- hectares (22,000 +/- acres) on Black Mountain, which contains the state’s highest point, as unsuitable for mining. A fast track legislative process was triggered which could have "taken"100 million tons of coal reserves or, in the alternative, imposed severe restrictions on mining. Even with all parties represented by reasonable individuals, this process can be extremely cumbersome and expensive. The legal and technical preparation for this unusual hearing process as well as issues and strategies of the negotiated resolution are reviewed.

Jan 1, 2000

By H Wright

Black Rock Cave (BRC) is a sublevel cave which was developed in 2018–2020 and has been in production since November 2020. BRC is part of the Mount Isa Mines complex and extracts a leached orebody comprising of high-grade chalcocite ore, situated below the historic Black Rock Open Cut workings. The mine is owned by Mount Isa Mines and operated under contract with PYBAR Mining Services. In 2021 a number of rockfalls occurred throughout the mine and were increasing in frequency. This culminated in a major rockfall on the decline in June 2021, after which the decision was made to withdraw all persons from the mine, initiate rehabilitation and conduct further investigations to deduce a safe method to provide long-term support. The rockfall investigations have shown that the corrosive nature of the highly leached rock mass can consume a split set in less than 18 months. A review of potential corrosion resistant ground support methods concluded that steel split sets have a safe lifespan of six months at BRC, and that all workings must have corrosion resistant support installed prior to exceeding the safe life of the friction bolts. The review recommended the use of 4 m cable bolts as the most suitable method of corrosion resistant support. This new support system, and the requirement to rehabilitate all mine workings within the leached orebody, had an impact to the schedule and an effect on both equipment and manning levels at BRC. Accelerated jumbo rehab allowed access to the production levels within two months of the rockfall. Cable bolting then followed the jumbo bolting in all leached areas. The direct impact has been ten months of reduced production, due to night shift closures of the decline to enable cable bolting. The impact to the mine has been minimised by the small flexible team that enabled the mine plan to change rapidly and often to accommodate the challenging conditions. In less than two months from the rockfall event, production had resumed. Within ten months of concluding that the mine required; full rehabilitation, a new support system and a full re-schedule, normal mining operations had restarted, with pre-event productions rates being achieved.

Mar 29, 2023

By Fan Delian, Ye Jie, Lui Tiebing

The lower and the upper parts of the Doushantuo Fonnation, Hubei Province, China, contain silicate-type K-rich beds (illite and feldspar), and intraclastic phosphorites, as well as Ag-V and V deposits in a "Black Shale Series". The K-rich beds fonned in an anoxic basin whereas the phosphorites fonned in a more oxic and higher energy depositional environment. The Black Shale Series occurs in the lower and upper parts of the Doushantuo Fonnation; that in the upper part consists of black illite shale and dark gray dolostone, and contains Se-rich Ag and V deposits. These deposits are of more industrial significance than the previously discovered Ni-Mo polyelement sulfide deposits which occur in the Lower Cambrian Black Shales Series of South China. Studies of lithotype, sedimentary sequence, and geochemistry of the Doushantuo Fonnation have led to more attention being focused on the uppennost Black Shale Series and its Ag-V and V deposits. There are three ore types: black, Ag-V-rich, illite shale; black, V-rich, illite shale; and dark gray, Ag-Vrich, fmely crystalline dolostone. The first two ore types contain 3070 to 5% Corg and the last, 1.25%. The Ag-bearing minerals are naumannite, argyrodite, aguilarite, acanthite, and native silver that occur as inclusions in pyrite associated with barite. Vanadium substitutes for AI in illite and is also related to organic-matter contents. Because (1) the pre-Sinian Kongling Group contains one to three times greater than the Clark Ag value; (2) black, illite shale has a negative Ce anomaly; and (3) there are large occurrences of black, K-rich, tuffaceous, fme siltstone, the sources of Ag are thought to include subaerial and submarine volcanic materials. It is proposed that Ag, V, and Se were absorbed by clay particles and organic matter during syngenetic deposition in an anoxic environment; Ag subsequently was reconcentrated into sulfides and selenides, whereas V was incorporated structurally into illite during early and late diagenesis. These types of Black Shale Series-hosted Ag-V and V deposits are, therefore, considered to be sedimentary-diagenetic in origin.

Jan 1, 1992

By Hugh W. Evans

Many reports and papers have been delivered on projects under construction or already in operation, but we believe there are few that have been written about projects yet to be built specifically dealing with advanced mine and environmental planning. This paper describes such planning for Atlantic Richfield Company's Black Thunder mine. Project planning is a cyclic phenomenom involving four broadly overlapping planning steps (Figure 1). The demands of the public include needs that can be satisfied through planned resource development. Using a base of information that partly exists and must in part be gathered and updated, the preplanned development can be, evaluated. The evaluation process, with built-in environmental constraints leads to an implementation procedure. Implementation results in the development, including the release of the affected area to other public demands that follow.

Jan 1, 1975

By AIME AIME

BLANDFORD. C. BURGESS, the new Chairman of the Industrial Minerals Division, took the advice of Horace Greeley in reverse-he turned his hack on San Francisco and the Golden Gate, and after a few side excursions toward Alaska and Arizona, hit the trail eastward, not for the lonesome pine, but for Spruce Pine, N. C. Born Aug. 10, 1893, in San Francisco. Burgess found his first job, shortly after finishing high school at 19, as axeman for a surveying party of engineers working for the Southern Pacific Co. in Oregon. Later he moved on up with them into Alaska. He liked the engineering profession, and decided to equip himself further so he entered the University of California in the fall of 1913. and for the next two years devoted himself to acquiring an education in civil engineering.

Jan 1, 1945

By B. Law, M. Menabde, B. Baird

Blasor is a new mine planning tool which is being used in the long and medium-term optimization of multi-open-pit operations throughout BHP Billiton’s Base Metals and bulk commodities portfolio. It is not just a scheduler, nor even only a schedule optimizer—although this function lies at the heart of the tool’s functionality—but a pit development plan optimizer, used from ultimate pit design and process plant capacity sizing right through to mining phase design and optimal panel scheduling. The tool uses a mixed-integer-linear-programming optimization engine to determine when material should be excavated and where it should be sent to optimize discounted operating cash flow over the life of operation. The core software design concept of Blasor is to provide a tool which is intuitive and flexible enough so that a competent mine planner can perform a pit development plan optimization without assistance from optimization specialists. To this end, a generalized graphical user interface has been implemented which allows full configuration of the optimization problem, including the definition of all inputs and constraints, specification of the material flow topology, bin and destination class definitions and full specification of the economic model encompassing prices and costs. This paper describes the capability of Blasor and outlines the design concepts underlying its design philosophy.

Jan 1, 2007

By Frank Sames

The control of the environmental effects, especially blast vibration and airblast, has become a dominating planning criterion for most surface blasting operations. Compliance with existing regulations is generally achieved through constraints in the blast design, or monitoring programs. Commonly, blast vibration and airblast signals are rated and compared only by their maximum amplitude and the principal frequency associated with the peak.

Jan 1, 1997

By Carl Hendricks, Malcolm Scoble

There currently exists no viable means of obtaining continuous, quantified feedback on blast efficiency. This paper describes the adaptation of a loading shovel to serve as a diagnostic tool in evaluating the success of ground preparation practices. Work undertaken in a large western Canadian open pit involved microprocessor-based instrumentation for the performance monitoring of an electric mining shovel. The monitored shovel responses proved to be reliable indicators of variations in muckpile d&ability. This approach is considered to provide a very comprehensive survey of post blast conditions since the shovel must physically interact which every cubic yard of blast fragmentation.

Jan 1, 1991

By R. R. Rollins

Field data combined with theoretical derivations were used to design a surface mining operation using explosive casting. Calculated casting results varied from 44 to 65% depending on bench height. This model was then applied to field tests at an eastern, contour, coal stripping operation. Results from five experimental casting shots are summarized and compared to conventional mining methods. The overburden material removed by casting ranged from 35 to 65% with an average of 50%. Fragmentation was improved and it was demonstrated that this procedure is economically attractive with a resultant cost savings of $.59/m3 or $5.93/t of clean coal.

Jan 1, 1987

By McKenzie C. K, Stewart R. S, Simpson J

Blast control in small scale underground mining leads to improved fragmentation control, improved control over overbreak and dilution, and the optimisation of drilling and charging operations. Greatly improved control can be achieved through blast monitoring, to confirm proper implementation of blast designs and blasthole charging. Further improvements can be achieved through simple modelling, enabling blastholes to be placed in the correct locations and charged with the correct weight and strength of explosive. Improved design can be shown to significantly reduce overbreak and dilution, and even ground support costs. In one mine in Quebec, open stopes of widths varying from 2.5 metres to four metres and dipping at 36¦ to 38¦ were designed to achieve zero dilution using open sloping blasting practices. The first stope designed in this manner was monitored in detail and achieved its objective.A method for contouring damage around blastholes is presented as a basis for selection of drilling patterns, with particular application to the control of overbreak and dilution. Contouring can be used to provide reliable estimates of either overbreak or damage (where rock is broken het reynainc in nlarr)

Jan 1, 1993

By A Rorke, B Cubitt, R Beeslaar

The recent drop in the value of the South African Rand has resulted in an increased export value for South African coal and has lead to new coal reserves becoming available for mining. Very often these reserves are in close proximity to existing structures and utilities thus calling for stringent blast control measures to keep the risk of vibration, air blast and fly rock damage to a minimum.

Jan 1, 1997

By Laura Bastemante, Bruce Vandenberg, Fred Huettig

Recent advances in solid-state, field portable, fast framing video camera systems and PC based frame capture hardware now allow blast imaging up to loo0 frames per second. Up to 8 seconds of data can be stored directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the KineView 1256P system and compare these with the analogous aspects of film based cameras.

Jan 1, 1997

By Laura Bustemante, Bruce Vandenberg, Fred Huettig

Recent advances in solid-state, field portable, fast framing video camera systems and PC based frame capture hardware now allow blast imaging up to 1000 frames per second. Up to 8 seconds of data can be stored directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the KineView 1256P system and compare these with the analogous aspects of fii based cameras.

Jan 1, 1998

By Ron Beeslaar, Tony Rorke

The Professional Blast Manager is a blast design tool that has been developed in South Africa. It is aimed at mining and civil engineen, blasting contractors and mine planning engineers. The code can be used as a stand-alone package or be combined Into complex mine information systems.

Jan 1, 1998

By Raj K. Rajamani, Solomon A. Tucker, Michael K. McCarter

"In a study aimed at exploring possible improvements in operating performance at an Open Pit Copper (OPC) mine in the western U.S., the impact of blast energy changes on crushing performance was evaluated. OPC feeds its 3-stage crushing plant in 12-hour-day shifts with skarn ore from three domains: Pit_B (B), Pit_S Low-Grade (SLG) and Pit_S High-Grade (SHG), in the blending ratio 1:1:1 (B/SLG/SHG). Thecrushed product is fed to a 2-stage ball mill circuit. "

Jan 1, 2017

By P S. Jaitawat, M Sarim, M P. Roy, P K. Singh, A Joshi

Mining is being carried out using the sublevel open stoping method at the Kayad underground mine. The mine will ultimately reach a depth of 390 m. Kayad village is only 100 m (horizontally) from the underground mining areas. As a result, blast-induced ground vibration is one of the major issues for the residents of the village. This paper deals with the process involved in optimising blast design parameters at the development face blast, slot raise blast and ring hole blast to control blast-induced vibration within safe limits while ensuring improved production, productivity and safety. In total, 1041 development face blasts, 110 slot raise blasts and 52 ring hole blasts were conducted, and 2612 vibration data were monitored in the village at different locations. Initially, electronic delay detonators were used, with an emphasis on controlling vibration in the surface structures. Subsequently, shock tube (Nonel) initiations were used as the blasting faces reached lower depths. A comparative study was also performed for both the initiation systems. The orebody width generally varied from 3.1 to 7 m, and ring hole designs were optimised accordingly. The number of holes in a ring was up to seven and the depth was up to 23 m, depending on the size/width of the orebody. The ring blasts were performed with 64–340 kg of emulsion cartridge explosive and detonated with explosive weight per delay of 10.92–17.16 kg. Extensive experiments were performed and blast-induced vibrations were controlled in the village. Deck blasting (ie up to four explosives decks) was used in a blasthole and the explosive charges were separated by delay detonators, which helped to control the vibration in the village. The actual detonation time of each deck was recorded by monitoring the in-hole velocity of detonation of the explosives, and the charging patterns were optimised accordingly to get the desired blast results.CITATION:Roy, M P, Singh, P K, Sarim, M, Jaitawat, P S and Joshi, A, 2015. Blast design and vibration control at Kayad lead-zinc underground mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 533–544 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Melvin A. Sannes

The Pinson Mine has several different rock formations, running throughout the pits. The main types of material found are Alluvium, Shale and Limestone. In some instances, all three can be found within one blast pattern. Several areas have broken material, which makes it very hard to drill and to shoot. If not timed and loaded correctly a lot of the explosive energy is lost through the broken material.

Jan 1, 1998

By Paine GG

The in-situ retorting of shallow oil shale deposits is an attractive alternative to the material handling problems of conventional open pit mining techniques, which involve removing overburden, fragmenting and transporting the shale to a fixed retort, and finally disposing of the hot spent shale.For in-situ retorting to be successful, the oil shale has to be fractured and the fragmented rock expanded into a void, to allow controlled propagation of a flame front through the in-situ retort. The principles of cratering with explosives have been used to develop a process for the in-situ fracturing of a thin oil shale deposit overlain by a formation of porous rock. The overlying porous rock formation is first compressed by explosive charges to create voids in the porous rock. The oil shale is then fragmented and pushed in to the voids with separate explosive charges. This paper discusses methods of creating voids in porous rocks with minimal surface disturbance, and then methods of obtaining the most uniform fragmentation of the shale. The whole process can be completed, in practice, in one blast. The results of an experimental blast are presented, and possible modifications are then discussed.

Jan 1, 1985

By Terra Dinamica, Frank Lucca

This paper discusses blast design for vibration control in tight construction blasting. Topics include blast pattern geometry, blast design formulas, loading, explosives & initiation selection, and utilizing borehole deviation equipment and lasers, and rules of thumb. The paper will also explore vibration prediction, neighbor relations, and related topics, such as blast plan submittal. Various projects from metropolitan construction blasting operations will be used as examples. Examples include blasting in the inner city, next to pipelines, and in housing developments.

Jan 1, 2005

By G. R. Adhikari

Step 4: Selection of explosives and initiation system Various types of explosives are manufactured in India and a wide choice is available among them that include nitroglycerin based explosives, slurries, emulsions, ANFO (ammonium nitrate mixed with fuel oil) and heavy ANFO. The choice is also available between cartridged and bulk loading systems. In Indian mines, much importance is unduly given to the cost of explosives alone which is not conducive to optimization of blast design parameters. The concept of energy per meter of blasthole and the way in which the total explosive energy is partitioned between shock and heave is not considered in the prevailing practices. Besides, very little efforts are made to objectively evaluate the performance of explosives for a given site condition. Tailoring explosives is limited to changing the density of the bulk explosives. Cartridged explosives are still being extensively used in large operations where bulk explosives should be the preferred choice.

Jan 1, 2002