Search Documents

By C. H. Lee, K. Adham, D. Lemieux, J. P. Mai, A. M. S. Hussein, S. Francey

Copper concentrates contain an increasing amount of arsenic, as the older sources of cleaner ores are depleted. At the same time, the market-determined price penalties on arsenic rich concentrates are rising due to limited arsenic treatment capacity at smelters and increasingly stringent environmental emissions limits, necessitating arsenic removal from the copper concentrates. Heating the concentrate to about 700°C can remove significant amounts of arsenic (as elemental and/or sulfide); however, it is important to achieve that removal economically and with due consideration to post-roasting arsenic (toxic waste) treatment. A comparison is made among different roasting options (kilns, multi-hearths and fluid beds) to qualify their potential application to arsenic roasting of copper concentrates. Both direct and indirect methods of heating as well as inert, air and oxygen atmosphere options are considered. Technology comparisons are made with respect to the roaster’s operation, its off-gas treatment and arsenic stabilization. INTRODUCTION In the last twenty years, the arsenic content in globally produced copper concentrates have risen steadily due to the depletion of cleaner ores and the increase in complex concentrate production. Smelter contracts typically limit arsenic to less than 0.5wt%, with a penalty paid per unit of additional arsenic and other contaminants such as antimony. While penalties can vary, they can be on the order of $70/dry metric tonne of concentrate per 1% of arsenic. Strategies used by miners to avoid the price penalties have been to blend clean and complex concentrates, and to remove arsenic from complex concentrates to achieve smelter limits. Arsenic can be removed from copper concentrates by the heat-induced decomposition of the predominant enargite mineral (Cu3AsS4) at ~700°C. Roasting at such elevated temperature is a commercially proven option, but still suffers from process, cost and environmental challenges. After roasting, the released arsenic sulfide fumes can be separated from most of the entrained concentrate dust in cyclones. Then, the As2S3 laden off-gas can be oxidized to generate a still volatile oxide (As2O3), which can be further separated from the residual concentrate dust in a hot electrostatic separator. Next, the off-gas can be cooled with air or water, to either deposit the arsenic oxide in a dry or dissolved state. Dissolved arsenic acid can be oxidized to As(V) and reacted with iron to yield a stabilized ferrihydrite precipitate or scorodite that can be safely disposed. In the case of dry arsenic trioxide, it can be mixed with reactants (e.g. iron) and fluxes before thermal stabilization in a glass matrix, thus eliminating the need for costly oxidation.

Jan 1, 2019

By Z. T. Bieniawski

Results of in situ investigations are discussed providing comparisons of rock mass deformability measurements by three methods: 'petite sismique' technique, the Goodman borehole jack and flat jacks. The tests were performed in exploratory tunnels constructed for site characterization purposes of an underground hydro-electric scheme. Due to the large number of data (41 petite sismique measurements, 45 Goodman jack tests and 19 flat jack measurements), it was possible to evaluate thoroughly the testing techniques employed. The purpose of this paper is to indicate the problems encountered in the interpretation of the results and to offer suggestions for selecting in situ tests. INTRODUCTION In situ tests are expensive and time consuming but they are an important aid in tunneling applications since they can provide deformability data of rock masses in contrast to rock material characteristics obtainable from small laboratory specimens. Some in situ tests are relatively easy to perform but their reliability may be in question unless a comparison of the data obtained by several different test methods is possible. Although many in situ techniques are available for determination of rock mass deformability (1), those more convenient to use are the Goodman jack, flat jacks and 'petite sismique. These methods are considered convenient because the Goodman jack is a borehole device; flat jacks can provide not only deformability data but also information about the stress field around excavations; while 'petite sismique' is based on seismic refraction surveys. Accordingly, these three methods have been selected for comparison.

Jan 1, 1979

By R. J. McLaughlin

Acid mine drainage (AMD) can occur as a natural phenomenon through oxidation of sulfide minerals. Oxidation by air and water can be exacerbated by mining. Because AMD can exhibit low pH, it is capable of extracting heavy metals from mineral deposits. The result is highly acidic drainage with elevated heavy metal concentrations -the combination of which can cause extensive environmental damage. Because of the importance of these factors, this paper is focused on sulfate based AMD. Due to widespread mining, the occurrence of AMD is ubiquitous. As a result, several approaches to treatment have been developed. Chemical treatment using alkali is most commonly employed to treat AMD. There are alternative methods of treatment, as well as alternative ways of handling treatment sludges or concentrates. Dewatering of sludge or concentrates is beyond the scope of this paper.

Jan 1, 1996

By D. Lindeman, R. M. Nendick

"From a technologist's point of view, there have been few fundamental 'breakthroughs' in the process of gold extraction since the turn of the century. However, the industry has made a great deal of progress in its response to the problems that have arisen: a changing demand for products, lower grade and more refractory ores, inflated labour and materials cost and the increasing control of governmental legislation. The trend in North America and South Africa to alleviate these problems has been to adopt a common policy to process larger tonnages of lowgrade ore through more efficient milling circuits. Here, however, is where the similarity ends.The purpose of this paper is to emphasise the different principles of practice employed by extraction plants in North America and South Africa to achieve the same common goal, namely gold bullion.2.0 INTRODUCTIONTwo very important aspects of extraction metallurgy for which the metallurgical engineer is responsible are plant design and plant commissioning.In North America and South Africa the importance of these aspects is due to the fact that both are related to the financial success of the project of which they form part. Good design is imperative if the capital invested in both the plant and the whole mining undertaking is to reap maximum profit. Furthermore, good design leads to a carefully planned and well executed start-up procedure resulting in bringing the plant into production on time, at designed efficiency and within budget.Due to the competent nature of the quartz pebble conglomerate and quartzite ore on the South African Witwatersrand, the characteristics of the ore type are not much different from one mine to the other. Thus a significant operating knowledge and experience has been built up over the years and there is considerably less risk in selecting a gold extraction process route."

Jan 1, 1992

By Michael D. Justason

This paper details the static and Statnamic load testing on a 600 mm square pre-stressed concrete pile. The pile was located at Pier 15 on the 20 million-dollar Bayou Chico Bridge Project in Pensacola, Florida. The pile was 10.5 meters long and had a design load of 1.3 MN. Three static load test cycles were performed in November, 1996. The Statnamic load test was performed in January, 1997. The Davisson Failure load of the first cycle of the static test was 3.7 MN, and the Davisson Failure load of the Statnamic test was 3.2 MN. The load-displacement curves for the two types of tests were very similar, indicating that the Statnamic load test performed well in the sandy soils. Strain gauges embedded in the pile showed 35% skin friction and 65% end bearing for both test methods. Strain gauges were located at equal spacing at five elevations in the pile. A toe accelerometer verified the rigid body assumption of the Unloading Point Method currently used in the analysis of Statnamic load tests. The data collected from the pile instrumentation was of excellent quality and represents some of the best research to date comparing static and Statnamic load tests.

Jan 1, 1997

By Gary R. Corbett

The federally owned Cape Breton Development Corporation (CBDC) mines approximately 2.5-3.0 Mt of coal per annum from its Phalen Colliery. As part of an ongoing process to become more commercially viable the Corporation has implemented changes in its support method, namely, the transition from traditional steel set inseam supports to roof bolts as primary support in the single entry longwall retreat drivages. During 1991 and 1992, a monitoring program was implemented by the Cape Breton Coal Research Laboratory (CBCRL) to determine the loading on support systems and ground reaction in the gateroads in front of the retreating longwall faces of the 4 East and 5 East panels at Phalen Mine. The 4 East gateroad had been supported by steel sets alone. The 5 East gateroad had been supported by steel sets as well as roof bolting and strapping of the gateroad roof. Steel sets in both gateroads were instrumented with strain gauges and load cells to record support reaction to the retreating face abutment pressure. Multipoint borehole extensometers and multipoint strain gauged roof bolts were installed in the gateroad roof to monitor strata displacement and bolt loading above the gateroad as the longwalls retreated. This paper describes the details of the instrumentation and monitoring techniques utilized during this program and discusses the results, trends and differences observed in the two differently supported access roadways. Work on future data acquisition instrumentation is also briefly described.

Jan 1, 1993

By Elizma Ford, Vincent Sithole

"Two shortened test procedures for estimating the Bond ball work index are compared for suitability of use on Zambian/DRC-type copper–cobalt ores. The first procedure is based on a batch milling test while the second procedure is based on a limited locked-cycle test. Both procedures were conducted using a standard Bond test mill. INTRODUCTION The Bond ball work index is widely used in the field of minerals processing as an indicator of ore grindability. The work index is determined by means of a locked-cycle test procedure that typically requires seven to eight cycles to stabilise at a re-circulating load of 250%. A typical test requires between three to four kilogram of ore sample and around eight hours of operator time. For geometallurgical test work applications, where a large number of variability samples are to be tested, it would be highly beneficial to use a test procedure that requires less sample mass and operator time. Certain test work laboratories, for example SGS and JK Tech, are already offering various types of shortened test procedures for estimating the Bond ball work index. This paper discusses a comparison of two shortened test procedures that were evaluated for suitability of use on Zambian/DRC-type copper–cobalt ores. EXPERIMENTAL Test Procedure 1 – Batch Milling The first test procedure is derived from a batch milling approach proposed by the University of Hacettepe (Aksani, 2000). Some modifications were, however, made to the data analysis method from that originally proposed. During this test procedure, a 700 mL volume of sample is milled in a standard Bond test mill for a pre-determined number of revolutions. The feed and product particle size distributions are measured for each test. These results are then used to back-calculate a cumulative breakage rate parameter (k) for each particle size, according to the following formula:"

Jan 1, 2015

By Kuo En Chang

Many rare earth - transition metal (RE-TM) compounds absorb/desorb hydrogen reversibly at room temperature and atmospheric pressure. For LaNi5 which is used as a battery material, the electrochemical nature of this process is well known. In the case of Nd-Fe-B which has found wide application as a powerful permanent magnet, the absorption of hydrogen has both significant advantages and disadvantages. However, a fundamental understanding of the hydrogenation process at ambient temperatures and its effect on subsequent corrosion behavior is currently lacking. This paper reports the results of the hydrogenation of NdFeB two alloys, (NdDy)15Fe78.3A10.7B6 and (NdDy)15Fe67Co5V4A12B7, which are compared with that of LaNi5. Results show that hydrogenation can be accomplished by either electrochemical methods or immersion in dilute sulfuric acid. For the latter method, the change in lattice parameter indicates that the level of hydrogen absorbed by the NdFeB particles corresponds fairly closely to an overall composition of Nd2Fe14BH2.7. Cyclic electrochemical charge/discharge experiments show that the maximum hydrogen discharge capacities of the NdFeB, NdFeB-Co-V, and LaNi5 are 40, 60, and 210 mA?h?g-1, respectively. Anodic potentiodynamic polarization measurements and calculated values of icon reveal that absorbed hydrogen in NdFeB-Co-V and the NdFeB may lead to significant increases in corrosion rates.

Jan 1, 1995

By Steve Wilson, Bern Klein, Jeff Drozdiak, Stefan Nadolski, Andrew Bamber

"In the adaptation of high pressure grinding rolls (HPGRs) to hard-rock mining applications, circuit development has mainly focused on placing HPGRs in the role of tertiary crusher in the preparation of ball mill feed. In order to take advantage of the potential energy benefits associated with HPGR and stirred mill grinding technologies, work was done to investigate the potential of and resultant energy benefits of placing the HPGR in series with a high speed stirred mill in replacement of the conventional cone crusher / ball mill arrangement. The proposed circuit was designed to operate with two stages of HPGR grinding followed by high speed stirred milling.Using a pilot-scale HPGR unit inline with a 20 liter stirred mill, the design criteria, circuit arrangement and consequent comminution energy requirements for a circuit processing copper sulphide ore from Teck Resources’s Mesaba Copper project were determined. These results were then compared to two other circuits, an HPGR / ball mill circuit and a conventional crusher / ball mill circuit processing the same ore.The testwork indicated at a proof-of-concept level that the HPGR / stirred mill circuit could potentially be appropriate for this duty and further work on the concept is merited. While the results indicate that the HPGR component of the circuit was more energy efficient than conventional cone crushing, the energy efficiency of the stirred mill was found to be lower than that of a comparable ball mill undertaking the same duty. However, increased energy efficiency of the stirred mill portion of the circuit is possible with further optimization and further work on the concept is indicated."

Jan 1, 2010

By E. Chen, M. Barati, K. Coley

The reaction between carbon and slags is of significant importance in direct smelting of iron ores, EAF slag foaming and copper slag cleaning processes. This reaction is known to occur via gaseous intermediates and it is important to have fundamental data to understand the relative importance of each reaction step. In this study, the rate of CO2dissociation on different slag surfaces is measured using an isotope exchange technique. It was found that increasing iron oxide content up to 30 wt per cent does not have a significant effect on the rate constant while increasing from this limit, increases the rate constant dramatically. Activation energy of CO2dissociation on slags of unit basicity and different iron oxide contents is in the range of 180±40 kJ/mol. It is found that rate constant dependence on oxygen potential in the slag phase is increasing with iron oxide concentration. In the case of copper making slags, the influence of copper oxide is found to increase the magnitude of apparent rate constant, while decreasing the activation energy considerably. Key words: Gas-slag reaction, CO2dissociation, copper slag, kinetics, isotope exchange

Jan 1, 2004

By P. S. B. STEWART

As part of a continuing study of mechanisms of breakage, the grinding at Nairne Pyrites Pty. Ltd. was traced by the addition of barytes and the results compared with parallel small scale laboratory tests. It was confirmed that the same basic mathematical functions described the behaviour of the full scale ball mill as those established in the small scale mill. However, an additional classification function was required to define the behaviour for the rod mill and was evaluated as a function of size from the experimental data. The classification and grinding of the pyrites ore was assessed from steady state size distributions around the circuit.

Jan 1, 1971

By Ihsan Berk Tulu, Keith A. Heasley, Chris Mark

"The Analysis of Retreat l\.fining Pillar Stability (ARJ\1PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover. To this end, the National Institute for Occupational Safety and Health (NIOSH) and the West Virginia University (WVU) l\.fining Engineering Department have been working together to improve both the ARJ\1PS and the Lal\.fodel programs.This paper compares and analyzes the overburden loads calculated by ARJ\1PS 2002, the new ARJ\1PS 2010, and the Lal\.fodel program with regard to the retreat pillar line, the gob, and the barrier pillars. The analysis shows a number of distinct differences between the ARJ\1PS and Lal\.fodel loading distributions. Ultimately, the programs, with their distinctive load distributions, are used to analyze a database of 52 deep cover pillar retreat case studies, and the ability of each program to discriminate between successful and unsuccessful retreat pillar plans is evaluated.INTRODUCTIONThe Analysis of Retreat l\.fining Pillar Stability (ARJ\.f PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover.Pillar recovery accounts for less than 10% of the coal produced from underground coal mines; however, in the period between 1989 and 1996, it accounted for more than 25% of all ground fatalities (l\.fark et al., 2003). In the past 15 years, the safety of retreat mining operations has greatly improved. l\.fark (2009) explains three steps promoted by l\1SHA and NIOSH for safer pillar recovery:1) Global stability through proper pillar design2) Local stability through proper roof support3) Worker safety through proper section managementThe ARJ\1PS and Lal\.fodel (Heasley, 1998) programs have been playing an important role in guiding mine operators in designing pillars to ensure the global stability of a retreat panel."

Jan 1, 2010

By P Hagan, S Wang, D Li, B Loh

A study was undertaken to quantify the differences in performance between a full-length encapsulated cable bolt and a partially encapsulated cable bolt. Much research has been reported on the differences in cable bolt design and operational parameters such as borehole diameter and grout type with much of this based on the Laboratory Short Encapsulation Pull Test (LSEPT). However, there is a gap in knowledge surrounding the effect of anchorage length on load transfer and cable bolt performance particularly with respect to the role of the bulb in modified cable bolt designs. The objective of this study was to expand the existing knowledge base of cable bolt performance with the intent of developing a revised design criterion. Alongside a comprehensive review of current cable support theory, design and practice, a series of pull tests was undertaken to compare each anchorage method using a high capacity modified cable bolt. The results serve to confirm earlier work on fully encapsulated anchorage. Both the peak load capacity and stiffness of the fully encapsulated cable bolt were nearly double that of the partially anchored cable bolt. When the tests were repeated in an oversized borehole, while there tended to be more variation in performance, there was little significant difference in the mean results. In addition to anchorage length, there are other factors that contribute to cable bolt performance including in order of sensitivity: embedment length, water-to-cement ratio of the grout, type of grout and borehole diameter. CITATION:Loh, B, Hagan, P, Li, D and Wang, S, 2018. A comparison of the performance of fully versus partially encapsulated cable bolts based on laboratory-scale testing, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 291–302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By R. V. Ramani, R. Bhaskar

"While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mi ne environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use.As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined.The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.INTRODUCTIONThe sampling of airborne dust in mines can be done for several purposes. Traditionally, dust sampling has been restricted to the gravimetric measurement of airborne respirable dust to comply with the regulations governing the mining industry. Instruments such as the MRE gravimetric sampler, and personal gravimetric samplers that have collection characteristics similar to the human respiratory system have been in use for the last two decades. Presently available instrumentation for the purpose of regulation have been considered adequate by the Committee on the Measurement and Control of Respirable Dust in Mines (National Academy of Sciences, 1980),"

Jan 1, 1989

By R. Loots

High temperature creep resistant alloys are used in power plants as steam pipes and headers where they have to withstand super heated steam temperatures of up to 600ºC for the lifetime of the plant. Frequently certain portions of pipes may be subjected to excessive temperatures and consequently suffer from creep damage. Damaged portions then have to be replaced by welding new steel to the service exposed steel. Such welds will have to be subjected to a post weld heat treatment (PWHT) to relieve residual stress. During such a PWHT it is then possible for the steel to crack in the heat affected zone (HAZ) by what is known as Reheat Cracking (RHC), also known as stress relief cracking. For the present purpose the RHC susceptibility of service exposed steel was compared with that of new steel by reproducing the temperature cycle to which the HAZ will be subjected during welding in a weld simulator. This was followed by PWHT where the influence of residual stress was studied by applying a constant stress to such a weld-simulated specimen in a creep testing machine. A sharp spiral was machined along the length of the cylindrical specimen to simulate the presence of a possible weld defect. In this way it is possible to subject all portions of the simulated HAZ to the same stress intensity. For the purpose of the investigation 1/2Cr-1/2Mo-1/4V steel known to be susceptible to RHC was chosen. During testing a constant tensile stress was maintained while the temperature was increased to follow the thermal cycle prescribed for PWHT. It was found that the new steel in all instances failed by RHC along the grain boundaries in the high temperature heat affected zone. In the case of the service exposed steel the creep strength of parent metal was lower than that of new steel as a result of exposure to a steam temperature of 540°C for about 15 years. Consequently, all of the failures during testing occurred in a ductile manner by necking outside the HAZ rather than by RHC. When service exposed steel is welded to new material, it is expected that the creep strain associated with stress relaxation will mostly be concentrated in the parent steel outside the HAZ. Accordingly, it should probably not be necessary to make any extra allowance for reheat cracking during repair of steam pipes manufactured from 1/2Cr-1/2Mo-1/4V steel other than that applicable for welding new steel.

Jan 1, 2004

By J. W. Leonard

Since the interpolation of exploratory data 1 can be no better than sampling procedures, a series of field experiments were conducted in an effort to determine whether hand-cut channel or core washability determinations best represent continuous miner produced run of mine coal. By obtaining a core drilled to within a few feet of channels taken from an underground face and then overmining both locations; core, channels and run-of-mine coal allocations were obtained from a common sample and all allocations were subjected to identical washability determinations. In order to compare results, basic rules2,3 previously anticipated and later published by the writer were employed. The first rule states that "For any full seam washability determination, the sulfur versus ash function for increasing cumulative specific gravity float coal fractions is linear". The second rule states that "For any full seam washability determination, the recovery versus ash function for increasing cumulative specific gravity float coal fractions is logarithmic".

Jan 1, 1988

By J. P. Landriault, F. W. Harrison

"Zinc-iron alloy coatings can be produced by either thermally alloying hot-dipped galvanized steel or by electro deposition. Stelco Inc. produces a thermally alloyed Zn-Fe alloy-coated steel, which is mechanically wiped to remove free zinc.A more extensive use of Zn-Fe alloy-coated steel has been predicted for unexposed autobody and structural part applications, since this material is characterized by good spot weldability and formability, and provides superior corrosion resistance under automotive primers.This investigation has examined the coating composition, corrosion resistance, spot weldability and formability of Stelco's Zn-Fe alloy-coated steel and found its properties to be similar to those of Zn-Fe alloy-coated steel produced by post coating annealing.IntroductionRecently, there has been increased automotive interest in galvanneal, which is characterized by good spot weldability, good paintabilityt and good corrosion resistance when primed. Stelco produces a thermally alloyed zinc-iron coated sheet product similar to galvanneal. However, this product is produced by mechanically wiping the free zinc from the surface of hotdip galvanize to expose the underlying zinc-iron alloy.The surface of Stelco zinc-iron alloy-coated sheet is matte gray and has longitudinal streaks which result from contact with Kevlar wipers during production (Fig. I). This paper describes the coating composition, corrosion resistance, weldability, formability and surface appearance of Stelco zinc iron alloy coatings and, wherever possible, compares these properties to those of galvanneal."

Jan 1, 1987

By R Minnitt

Two methods of calibrating the parameters K and Alpha for use in Gy’s formula for the fundamental sampling error were investigated. Approximately 480 kg of broken ore from Harmony’s Target gold mine in South Africa was used to compile the replicate samples for two experiments. The duplicate series analysis (DSA) and segregation free analysis (SFA) methods differ in terms of their approach to recovering the sized materials required for the calibration procedure. In this experiment the DSA method split off six more-or-less equal masses of material from a 75 kg lot that was successively crushed to finer and finer fragment sizes. The sublots so formed were split into 32 samples and fire assayed for gold. The SFA method used approximately 250 kg of broken ore crushed to 95 per cent passing 2.50 cm, which was then passed through successively finer screens until a sublot of less than 0.0075 cm was obtained. Each of the 15 sublots obtained in this way were split using a riffle splitter into 32 samples that were fire assayed. A total of 672 fire assays were used in these experiments. The sampling parameters K and Alpha were used for the compilation of a nomogram and to calculate the gold liberation size of the ores. While there are no definitive results in terms of the actual gold grain sizes against which the calculated sizes can be compared, it appears that the DSA method produces more acceptable results.CITATION:Minnitt, R, 2014. A comparison of two methods for calculating the constants K and alpha in a broken ore, in Proceedings Sampling 2014 , pp 165–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By R. Patterson

Tracer gases have been utilized successfully in a variety of industries, each with specific releasing and sampling methods. The various attributes of tracer gases are dependent on the industry the tracers are utilized in. Tracers must be chemically and thermally stable, safe, odorless, detectable at low concentrations, have a low background concentration, and should not be naturally occurring in the environment if they are utilized in underground mining applications (Thimons et al., 1974). In addition, the tracer gas should be inexpensive, non-corrosive, non-toxic, easily transportable, readily attainable, and non-radioactive (Kennedy et al., 1987). Sulfur hexafluoride (SF6) met many of these above requirements and therefore was introduced as an ideal tracer gas to use in mining industry in the early 1970?s (Thimons et al., 1974). Due to the nature of underground mining including complicated geometry, irregular flows, turbulent flows, obstructed airways, and leakages it is difficult to use conventional anemometer and smoke tube techniques to accurately measure the effectiveness of ventilation controls (Thimons et al., 1974; Klinowski and Kennedy, 1991). There have been several applications of SF6 as a tracer gas in underground metal/non-metal and coal mines. Thimons et al. conducted early testing of SF6 in an underground limestone mine and determined that it is an effective technique for evaluating auxiliary fans, estimating volumetric flow rates in large areas, and measuring low flow velocities. A rapid face ventilation measurement method (FVM) utilizing SF6 was developed by the Bureau of Mines to make face measurements in underground coal mines (Timko and Thimons, 1982). When measuring the effectiveness of jet fans in dead headings SF6 was proven more effective than smoke tubes (Timko and Thimons, 1982). Experiments related to determining methane liberation in the gob were also conducted by injecting SF6 into a borehole (Timko and Thimons, 1982). Also, in an emergency situation where the gob had to be sealed due to a fire, SF6 was released to determine the effectiveness of the seals (Timko and Thimons, 1982).

Jan 1, 2011

By M I. Pownceby, C M. MacRae, A Torpy

Electron probe microanalysis (EPMA) and quantitative X-ray diffraction (QXRD) techniques are capable of providing high-quality quantitative information regarding the phase mineralogy and distribution of alumina within iron ore samples. The techniques, however, use different methodologies in determining the mineralogical information (ie structural versus chemical), which introduces some limitations. In this study, EPMA was used to identify and quantify the deportment of alumina within mineral phases in iron ore samples (-1 mm crushed) sourced from different suppliers. Results were directly compared with quantitative mineralogical data derived from QXRD to provide an evaluation of the relative merits of both techniques. The four ores studied contained alumina either in the form of gibbsite, aluminosilicates (eg kaolinite), or associated with goethite.For minor phases, gibbsite and kaolinite, the abundance trends measured via QXRD were generally reflected in the EPMA data. Agreement was less satisfactory for the more abundant goethite phase (both low- and high-Al forms). The discrepancy may be the result of sampling issues arising from textural features such as grain size, and also a systematic overestimate in the amount of Al-rich goethite when hematite and Al-bearing phases are finely intermixed and the EPMA step size is coarse. A second difference in the EPMA results compared to the QXRD data was in regard to quantification of low-Al and high-Al goethite phases. The sensitivity of the chemical-based EPMA was better for distinguishing between high- and low-Al goethite although the results remain overprinted by potential errors introduced via sampling.Care should be taken when directly comparing results from each method, although in general the data should be considered complementary, as each approach provides slightly different results and interpretations regarding the overall mineralogy.CITATION:Pownceby, M I, MacRae, C M and Torpy, A, 2017. A comparison of X-ray and electron-based analysis techniques for characterising the mineralogy and alumina distribution in iron ores, in Proceedings Iron Ore 2017, pp 593–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017