Search Documents

By Lei Wang, Qi Zheng, Xiao-kui Che

"The wastewater emitted by gold chemical industry contained vast of different heavy metal ion, such as Zn, Cu and Ni etc. Among them Zn is the main ion in the waste water which causes the serious environment pollution. A method of preparing a kind of resin which is used for the removal of Zn by magnetic adsorbent was developed and was applied in practice. This adsorbent is a chitosan made of a kind of Fe3O4-chitosan modified by epichlorohydrin. The adsorption capacity of the absorbent and it was concluded that under the laboratory conditions, the maximum adsorbing capacity of this adsorbent could be 287.58 mg/g. The absorbent was also applied in the wastewater emitted by a gold industry in Shandong province. Its performance was tested and the result showed that the concentration of Zn ion in the wastewater was reduced from 0.58 mg/L to 0.0174 mg/L. What is more, the adsorption rate could be more than 97% when the dosage was 100L/m3 after adsorbing for 1h. KEYWORDS Selective, preparation, laboratory experiments, industry experiment, comparation INTRODUCTION Currently, most gold chemistry use cyanide to leach gold ore. Many different metals participate to this reaction besides the gold ion in this processing, so that the composition of the water is very complex. The waste water emitted by gold chemistry industry contains large amount of heavy metals. Definitely, if it was discharged without any treatment, the water would threaten the environment. The recuperation of any ion in the water would mitigate the pollution. Ion exchange resin, which is an effective material to do the water treatment with low cost, became widely applicated in this field [Yu-jiao Wang,2013]. Different kinds of resin were developed and the influence factors such as pH, adsorption properties and selectivity for different ions were investigated [CA Cruz et al,2018; PawanKumar et al.2016; Y Zhang, et al,2010; and ShengingSun, Aiqin Wang, 2006;]. The waste water mentioned in this article has a high Zn concentration, so a magic resin for Zn adsorption selectively we designed was used to manage this water. And the recovery of Zn could not only contribute to pollution abatement but also a best way to settle a dispute to the short of Zn resource. So the article mainly describes the preparation and the application of a kind of magnetic adsorbent used for the removal of Zn both in laboratory and industry. The aim of this article is to compare the effect of this resin in industry and laboratory?"

Jan 1, 2018

By Wangzhi Zhou, Huasheng Chen, Bowen Li, Meng Liu, Mingsheng He, Long Zou

Steel slag is an inevitable by-product from a steelmaking furnace such as a converter, an open-hearth furnace or an electric arc furnace. The yield of steel slag increases with the sharp rise of steel production. Utilizing the slag effectively and comprehensively is one of the important tasks to promote the development of iron and steel industry in China in a sustainable and efficient way. In this study, hot-poured steel slag from a converter was used to prepare ceramics by mixing with fly ash, microsilica, and quartz. After heating at 1100–1200 °C, the ceramics were well sintered. XRD revealed that multiple crystalline phases coexisted in the glass-ceramics, and the main crystalline phases were diopside and anorthite. SEM observation indicated that there was a plate-columnar composite structure in the ceramics. Reaction mechanisms were discussed.

Mar 1, 2018

By Gong-yi Guo, Yu-li Chen

"A partially-stabilized zirconia powder was prepared by metalorganic precipitation process from technical-grade zirconium oxychloride and the effluent of an acrylic acid plant. The effluent contained low molecular weight carboxylic acids, i. e., acrylic acid and acetic acid. The· developed process is based on the selective precipitation of acrylic acid at suitable pH values by the addition of zirconium oxychloride to the effluent. The resulting precipitate is a precursor that can yield a pure, ultrafine, and partially-stabilized zirconia powder. The evolution of formation of the partially-stabilized zirconia in the present process was investigated using thermal analysis, infrared spectroscopy, and X-ray diffraction technique. Environmental, technological and cost advantages will make the present process feasible for manufacturing advanced zirconia ceramics.IntroductionIn recent years the superior mechanical, thermal, electrical and chemical properties of stabilized zirconia have become the focus of growing scientific and technological interest, and hence resulted in various structural and functional applications. The great potential of the material has given rise to numerous preparation approaches to obtain the material with the excellent properties; nevertheless, an extensive number of programmes are underway worldwide aimed at understanding and improving both the preparation and behavior of stabilized zirconia ultrafine powders. (1 – 8)."

Jan 1, 2000

By Qiang Guo, Zongliang Zuo, Mengqi Wei, Qingbo Yu, Qin Qin

Activated carbons, derived from waste ion-exchange resin by CO2 physical activation, were applied to separate CO2 from flue gas against global warming. The BET specific surface areas of activated carbons at different activation temperatures and times were investigated. The CO2 adsorption capacity was tested under non-isothermal and isothermal conditions. The experimental results show that when keeping the activation temperature constant, the specific surface area increases firstly and then decreases with increasing activation time. For the given activation time, the specific surface area rises firstly and then declines with increasing activation temperature. The adsorption capacity decreases with increasing temperature. The maximum adsorption capacity is 51.46 mg/g under the condition of 298 K and pure CO2. Fractional order kinetic model is the best one to describe the kinetics of CO2 adsorption. The activated carbons show the potential to be an effective adsorbent for the removal of CO2 from flue gas.

Mar 1, 2018

By Shugang Hu

According to XRD, DTA and SEM detections, the hydration products of blast furnace slag (BFS) based cementing material SL, SLG. were studied in different age periods. The XRD analysis of cementing material SL hydration products showed that the composition of hydration products were mainly amorphous substances, few crystalline substances. Characteristic peak of ettringite hadn?t been found in the spectral line of DTA, and it hadn?t been found in the figures of SEM, either, which was accordant with the conclusion that the cementing performance of SL mainly coming from gel of hydrated calcium silicate (CSH) and hydrated calcium aluminate. However, the main hydration products of SLG are Aft, CSH, and AFm, which are similar to Portland cement. All results suggest that BFS is a suitable base material for cementation. Keywords: blast furnace slag, backfilling cementing material, hydration products, cementing performance

Sep 1, 2012

By Zhang Chuanfu

Keywords: solid solution, Ni-Co alloy powders, thermal decomposition, fibres. Synthesis of fibrous Ni-Co alloy powders was achieved by thermal decomposition of precursor of complex Ni-Co oxalates solid solutions obtained via modified coprecipitation method among intimate mixing solution of NiCl2?6H2O , CoCl2?6H2O and H2C2O4?2H2O in the presence of surfactant polyvinylpyrrolidone (PVP) and organic solvent ethanol. Scan electron microscopy (SEM), X-ray diffraction (XRD), X-Ray photoelectron spectroscopy (XPS), disperse energy X-ray analyses (EDX) were used to characterize the structure features and chemical compositions of the as-prepared fibres. The influences of decomposition conditions, including temperature, time, the flow rate of N2+H2, and the heating rate, on the morphology, average size and specific surface area of the Ni-Co alloy powders were investigated. It is found that a trend of the mutual alloying of nickel and cobalt: the formation of perfect solid solution for any compositions NixCo100-x was indicated and corresponding NixCo100-x alloys with fcc phase can be obtained under the optimal conditions.

Jan 1, 2005

By Chuanfu Zhang

Based on Thermogravimetric and Differential thermal analysis (TGA-DTA), porous copper powder is prepared by thermal decomposition of complicated copper oxalate. The effects of various conditions on the morphology, crystalline grain size and specific surface area of copper powder were investigated, including temperature, duration, mixing ratio of nitrogen and hydrogen. Furthermore, composition and morphologies of the products were characterized by X-ray diffraction (XRD), Scanning electron microscope (SEM) and BET adsorption isotherm. It is found that porous copper powder was produced under optimum conditions. The specific surface area is over 6.74 m2?g-1, and average pore size in particles is about 30.3 nm. After comparison of SEM images, the final product Cu well inherits the morphology of the precursor, thus a mechanism of in-situ decomposition is proposed.

Jan 1, 2009

By G. Zhu

The straight Y-shaped silica nanorods have been synthesized on Si wafer by thermal chemical evaporation of mixed powders of silica and graphite at 1300_ and condensation on Si substrate without assistance of any catalyst. The synthesized samples were characterized by means of scanning electron microscopy, transmission electron microscopy. The results suggested that the straight Y-shaped silica nanorods have uniform diameter about 50-200nm and neat smooth surface. The growth of such silica nanorods may be a result of the fluctuation of external conditions and internal structure faults causing a change in the growth direction of silica nanorods developed.

May 1, 2008

By H. Ding

Calcium carbonate/Titanium dioxide composite, characterized by coating TiO2 on the surface of CaCO3 particles, is an important substitute for titanium dioxide. This paper studies preparation method of CaCO3/TiO2 ,composites based on mechano-chemical effects, measures its properties as a pigment, analyzes the binding form and interface reaction mechanism between CaCO3 and TiO2. Through single finely grinding of CaCO3, co-grinding of CaCO3 together with TiO2, and mecha-no-chemical effects produced in the course of grinding, CaCO3/TiO2 composites can be prepared successfully. Results indicate that grinding fineness of CaCO3, co-grinding time of CaCO3 and TiO2, the weight ratio of grinding media to mineral feeding, and the amount of TiO2 have much influence on the properties of CaCO3/TiO2 composites. CaCO3/TiO2 composites have the properties same as titanium dioxide pigment, oil adsorption and ultraviolet adsorption same as TiO2, and 90% of hiding power as that of TiO2. Wet grinding of CaCO3 causes the production of mechano-chemical effect and hydroxyl group, through which CaCO3 and TiO2 can be bonded together. Repulsion occurs between the particles of CaCO3 and the particles of TiO2, respectively, they are both in good dispersion. But attraction occurs between CaCO3 and TiO2. TiO2 particles are distributed evenly on the surface of CaCO3. Therefore, coating of TiO2 on the surface of CaCO3 particles and chemical bond between them make CaCO3/TiO2 compo-sites have pigment properties of Titanium.

Jan 1, 2014

By Z. F. Hu

Tourmaline has the characteristics of piezoelectricity, thermoelectricity, spontaneous polarization and far-off infrared radiations. Ultra-fine powders of tourmaline have extensive applications in the fields of electron, chemical and environment protection, as well as health protection. The preparation technology of ultra-fine tourmaline powder is discussed. The key equipment of a pilot plant for producing ultra-fine tourmaline powder with jet mill and stirred ball mill is described. Using this pilot plant facility it is possible to produce tourmaline powder with particle size smaller than 100 nm, and a continuous production process can be realized. The final powder product has many superior performance such as high whiteness and large specific surface area, and it?s a negative ions emission can reach the value of 7190 ions per cubic centimeter.

Jan 1, 2014

By Mim Li, Huimin Lu, Lisha Yang

"CuInS2 thin films solar cells have drawn much attention for their low-cost, stability and high conversion efficiency. The electrodeposition of Cu-In precursor films, as the first step in making CuinS2 solar cells electrochemically in the air-and water-stable ionic liquid based on choline chloride/urea eutectic mixture has been investigated at constant potential. Compared with aqueous electrolytes, the large electrochemical window as well as the high thermal stability of this ionic liquid allow the direct electrodeposition of Cu-In precursor films. Then the precursor films were sulfuretted in a tube furnace at different sulfurization temperatures to optimize the films properties. The films obtained were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS).IntroductionCuInS2 is one of the most prospective absorber materials for low cost thin film solar cells, with a high conversion efficiency that exceeds 32% in terms of theory and nearly 13% in laboratory level [1-2]. In addition to its long-term stability, CuinS2 has a band gap energy Eg ranging from 1.3 to 1.55 eV and an optimal optical absorption coefficient reaching 105cm-1 [3-4]. CuinS2 thin films have been prepared by several methods such as spray pyrolysis [5-6], r.f.sputtering [7], vacuum evaporation [8-9] and electrodeposition. Comparing with vacuum methods, electrodeposition has lots of advantages such as less energy consumption, preparation big area thin film, stable system and enabling cheaper films.The electrodeposition of most technologically important metals has been shown to be possible from a wide range of ionic liquids. These ionic liquids are currently applied in a wide variety area. It is reported that the cell efficiency of chalcopyrite absorber layer (CIS, CISeS, and CIGS) via an electrodeposition route in laboratory condition has reached 11.3% [10]. Copper and indium alloy film is regarded as important precursor for the production of compound semiconductors with sulfur. The electrodeposition of the alloy film from room temperature ionic liquid (RTIL) has not been widely investigated. Only few alloy films, such as ZnTe, CdTe, GaAs and AlSb have been electrodeposited."

Jan 1, 2011

By P. Ramakrishnan, Ramjilal

Fine powders of lead zirconate titanate have been prepared by three different methods such as ball milling, conventional coprecipitation and spray drying. Different powders have also been prepared by changing the process variables in each method. These powders were analysed for particle size chemical composition and reactivity. DTA, TGA and x-ray analysis have been carried out to study the lead zirconate titanate formation with reference to calcination temperatures. The calcined powders were then consolidated by compaction and sintering. An attempt has bean made to explain the consolidation behaviour of these powders on the basis of powder characteristics.

Jan 1, 1980

By X. J. Lyu, Q. Liu, M. J. Lian, X. Q. Cao, X. F. You, B. O. Erdenekhuyag, H. Y. Zang

The slag-tailings based artificial reef concrete (ARC) is made of CaO-CaSO4 activated granulated blast furnace slag (GBFS) as cementitious material and deslimed gold ore tailings as aggregate. In order to investigate the potential application of the material as ARC, the strength development, hydration characteristics and application performance were investigated under different preparation conditions. Results indicated that using seawater as the mixing water can effectively promote the hydration of slag and generate a large amount of hydration products such as ettringite, CSH gel, hydrotalcite and Friedel ’s salt in the early curing period and so render the material with good early compressive strength. Seawater curing can also accelerate the hydration reaction in the early stage of hydration. The hydration reaction of slag and the compressive strength of ARC can be effectively promoted by increasing the specific surface area of slag. The 28-day compressive strength of the slag-tailings based ARC prepared with 30-50% CaO-CaSO4 activated slag and 50-70% tailings can reach to 19.88-42.87 MPa. Also, the material has a low surface pH value, good resistance to chloride ion penetration, and sulfate corrosion. Keywords: Artificial reef concrete, granulated blast furnace slag, deslimed gold ore tailings, compressive strength, hydration characteristics

Jan 1, 2020

By M. H. Forester, John D. Cooner

ANTHRACITE ALTHOUGH the unmined anthracite will last for approximately 150 years, most of the thicker and cleaner coal beds have been almost entirely first-mined and pretty well robbed, leaving much of the present and future production to come from thin and dirtier beds. Herewith is a section of one of the dirty beds being mined in the Wyoming region [ ] This section shows that 45.8 per cent of the bed is made up of impurities and that the 45 in. of coal in the bed is in five benches, the thickest of which is 19 inches. In some localities of the anthracite region there are 14 beds of minable coal. Orderly and proper mining of the coal makes it necessary to rob or second-mine-almost all beds have already been first-mined-in sequence from the top downward. Therefore the robbing of the few remaining portions of the thicker and cleaner beds is in many instances being held up by the mining of the overlying thin and dirtier coal beds. Impurities Impurities consist of fire clay, slate, rock, and bone. The latter, which is black, contains 40 to 60 per cent carbon and often resembles good coal. In some beds there are also bands of "blue" coal, which, as the name implies, is of a bluish slaty color. Although much of this "blue" coal has a carbon content almost as high as the good anthracite, it is not

Jan 1, 1943

By M. H. Forester, John D. Cooner

ALTHOUGH the unmined anthracite will last for approximately A 150 years, most of the thicker and cleaner coal beds have been almost entirely first-mined and pretty well robbed, leaving much of the present and future production to come from thin and dirtier beds. Herewith is a section of one of the dirty beds being mined in the Wyoming region This section shows that 45.8 per cent of the bed is made up of impurities and that the 45 in. of coal in the bed is in five benches, the thickest of which is 19 inches. In some localities of the anthracite region there are 14 beds of minable coal. Orderly and proper mining of the coal makes it necessary to rob or second-mine-almost all beds have already been first-mined-in sequence from the top downward. Therefore the robbing of the few remaining portions of the thicker and cleaner beds is in many instances being held up by the mining of the overlying thin and dirtier coal beds. Impurities Impurities consist of fire clay, slate, rock, and bone. The latter, which is black, contains 40 to 60 per cent carbon and often resembles good coal. In some beds there are also bands of "blue" coal, which, as the name implies, is of a bluish slaty color. Although much of this "blue" coal has a carban content almost as high as the good anthracite, it is not

Jan 1, 1943

By Thomas Fraser

WHEN the Bureau of Mines initiated the program of large-scale research and development in the field of synthetic liquid fuels authorized in the Synthetic Liquid Fuels Act of April 5, 1044, the Coal Preparation Section was assigned the task of obtaining data on the preparation characteristics of the coal in large reserves that might be adaptable to use in this new industry. It is natural that, as the rapidly developing general research program brought about new concepts of raw-material quality, preferred geographical location, and the like, the orientation of coal-preparation investigations should have undergone some change. The first major assignment was the sampling and testing of a series of typical American coals deemed to he suitable for hydrogenation based on early research work conducted by the Bureau of Mines. This first series of tests has been completed and is reported in this paper.

Jan 1, 1950

By Wufeng Jiang, Jiann-Yang Hwang, Suju Hao, Yuzhu Zhang

Lime was made by the calcination of limestone in a high pressure resistance furnace. The lime mineralogical phases and micro-morphologies was characterized by field emission scanning electron microscopy (FE-SEM). The lime activity degree was determined by acid-base titration, and the lime pore distribution was measured by mercury intrusion porosimetry (MIP). The results show that with the increase of calcination pressure, the lime activity degree is increased, and the lime develops a large pore structure. The desulphurization experiments were carried out in the induction melting furnace using active lime with different activity degrees as a desulfurizer. The results show that the desulfurization performance of lime is closely related to the activity degree. There is a strong positive linear relationship between the desulfurization rate and the lime ’s activity degree.

Mar 1, 2018

By Zhigang Liang

A carbon free precast block was prepared by using high-alumina fused corundum as aggregate and fused magnesia, and ultra-fine Al2O3 and ultra-fine SiO2 powders as matrix materials. A small linear expansion for the precast block was achieved through spinel formation from the reaction of MgO with Al2O3. The precast block showed a lower apparent porosity, higher hot modulus of rupture and better slag corrosion resistance compared to the traditional Al2O3-MgO-C brick. Moreover, the practical application of the precast block to the ladle lining proved it to possess a better thermal insulation which could effectively prevent the temperature drop of molten steel during the refining process. It can be predicted that the carbon free precast block could possibly be accepted as a new type of ladle lining material for the production of low-carbon and ultra-low-carbon steel.

Jan 1, 2009

By P Collier

From 1972 until 1989 when operations were suspended Bougainville Copper Limited (BCL, owned 53.58 per cent by Rio Tinto Limited) operated a large open pit mine and processing facility at Panguna on Bougainville Island, Papua New Guinea producing copper concentrate containing significant quantities of gold and silver.BCL has a stated vision of recommencing operations at Panguna. In 2008, Rio Tinto, on behalf of BCL, conducted a multi-disciplinary study to assess the technical and financial viability of redeveloping the Panguna operation. One of the key outputs of the study was a Joint Ore Reserves Committee (JORC) Code compliant mineral resource statement based on the existing block model and fundamental data, archived since mine closure. Historical data (including the resource block model and drill hole data) was recovered from computer archives by a former Panguna mine employee familiar with the various obsolete data formats, thus maintaining an unbroken chain of custody of the data by Rio Tinto since operations were suspended. No additional data were collected as part of this study.The extensive data and documentation archive facilitated a sufficiently detailed evaluation of the fundamental data and model to support an updated resource statement. Table 1 of the JORC Code was used to guide the model validation process.Reconciliation of blasthole and metallurgical plant data with the reserve model, indicated that the copper and gold drill hole composite database was significantly biased towards underestimation in several key domains due to a combination of the following: mineralisation loss during core loss, core loss (minor), vertical drill holes failing to intersect sufficient subvertical mineralised fractures and veins, drill hole spacing too wide, and variable diamond drill hole core size. The resource model evaluation was based on three material types (all previously mined at Panguna), that were defined based on cut-off grade and rock type parameters: direct feed ore – material for delivery directly to the plant, preconcentration and screening ore – subeconomic material beneficiated to produce fines of economic grade, and waste. Three pit shells and designs were generated based on three separate sets of economic parameters. These economic parameters were also used to assign material types to the block model. The three resulting models were then evaluated against the corresponding pit shells.Classification of the resource was approached conservatively due to the inherent bias in the drill hole data. Consequently only Indicated and Inferred resources were tabulated.The study highlighted the importance of maintaining detailed documentation pertaining to resource estimates and operational history, particularly reconciliation, and the value that can be added by a simple, low-cost data compilation exercise.

Aug 22, 2011

By Z. L. Huang

A new porous apatite product was prepared using phosphorite from Yichang China by a tem-plate-directed method in self-made reaction equipment under constant temperature and pressure. The product was characterized by XRD, FT-IR and SEM. The results showed that the product was a kind of micrometer porous sphere three-dimensionally structured by apatite nanoflakes, that the average thickness of nanoflakes was about 50 nm, that the average pore size was about 1.2 µm and that the particle average size was about 20 µm. Great amounts of Ca2+channel, high special surface area and regular spherical shape show the potential promising applications of this special porous apatite product in the fields of catalyst, medication, chemical engineering and environment engineering

Jan 1, 2014