Search Documents

Block caving is an underground mining method for the profitable extraction of massive, low-grade orebodies. Lately, it has become the mining method of choice, for many mining companies, because of depleted high-grade orebodies, and declining metal market prices. Block cave mining, however, still faces several challenges. Lack of access to the cave remains a major issue in understanding the rockmass response to mining for method optimisation. Improving our understanding of the rockmass response to caving will lead to safer and more productive operations. Combining large datasets from multiple sources with virtual reality scientific visualisation (VRSV) is a viable alternative to understanding complex cave behaviour without access to the cave. This is achieved using immersive environments with the ability to view complex multi-dimensional data (beyond 3D) graphically. VRSV offers a unique platform where it becomes possible to immerse the multi-disciplinary experts, and/or management team, in a virtual mine environment for quick decision making and fast resolution to conflicting conclusions. The underground mining system is complex due to multiple interrelating factors such as geology, excavation geometries, stress and time. Block caving is even more complex than most underground mining methods due to the network of tunnels required, and the use of induced stress, among others. As a consequence of the complexity in the block caving environment, it is vital that the mining system is analysed holistically, as a system, rather than optimizing individual factors one at a time. This paper presents a customised software module developed for use in the Advanced Visualisation Interactive Environment (AVIE) at The University of New South Wales (UNSW), Australia, to enable VRSV investigation into block cave mining systems (BCMS). This approach has the potential to provide a better understanding of the effect of time in in rock engineering, which has proven to be an important factor in hard rock mines (Ma & Daemen, 2006; Malan et al., 1997; Suorineni, 2010) but never validated. This work back analyses the early undercutting phase of a case study block caving operation with the view to understanding time/sequence effects. There is evidence that heterogeneous rockmass time-dependent behaviour governs the seismic response of the rockmass following undercut developments.

Jan 1, 2015

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By Kiseong Hyeong, Young-Tak Ko, Gee Soo Kong

"The benthic environmental impact experiment addresses environmental impacts at a specific site related to deep-sea mineral resource development. For such a purpose, since 2010 we have carried out essential environmental research at both the BIS and a preservation site. We have acquired several tens multi- or box core samples at 32 sites within the BIS especially between 2011 and 2013, aiming to examine the basic properties of surficial deep-sea sediment as the potential source for deep-water plumes.In this study, we present physical the properties such as water content, shear strength and also geochemical properties such as major elements, rare earth elements (REEs), heavy metal contents at the BIS. Such proxies vary distinctly according to the Facies association. The lithology of all core sediments in the BIS corresponds to both Association Ib (Unit I/Unit II) and Association IIIb (Unit I/Unit III) on the basis of the KORDI classification (KORDI, 2004); Unit I is watery mud and dark grayish brown (10YR4/2) to dark brown (10YR4/3). Unit II is highly bioturbated mud and brownish yellow (10YR6/6). Unit III is very dark brown (10YR3/2) to black (10YR2/1) mud. Physical properties of these sediment types show that Association Ib is distinct from Association IIIb. The vertical profile of water content changed more sharply in Association IIIb probably due to compaction; water contents varied from 230 to 300% in Association Ib and changed from 200 to 250% in Association IIIb. The vertical profiles of shear strength are also quite different between Associations; the profile curve in Association IIb is much more gentle due to bioturbation."

Sep 1, 2014

Researchers from the National Institute for Occupational Safety and Health (NIOSH) are developing a coal pillar rib rating (CPRR) technique to measure the integrity of coal ribs. The CPRR characterizes the rib composition and evaluates its impact on the inherent stability of the coal ribs. The CPRR utilizes four parameters: rib homogeneity, bedding condition, face cleat orientation with respect to entry direction, and rib height. All these parameters are measurable in the field. A rib data collecting procedure and a simple sheet to calculate the CPRR were developed.

Jan 7, 2020

By D Cork, R Peet

"Methane is a signifi cant greenhouse gas. Methane is released from coal seams during the mining process, both in surface and underground operations. This uncontrolled release is termed æfugitive emissionsÆ and in underground mines is transferred to the atmosphere in ventilation air, known as ventilation air methane (VAM). The global VAM emissions are over 369 Mt of CO2-e/a (Butler, 2011; US EPA, 2010). Coal mines may abate this VAM or consider abatement should there be a price on carbon. These fugitive emissions are heading towards ten per cent of AustraliaÆs emissions by 2020 (Department of Climate Change, 2011).There are safety issues involved in VAM destruction. Due to the nature of coal, and coalextraction, unpredicted methane spikes above the lower-explosive-limit (LEL) can occur in theventilation air; for example outburst events or ventilation failure. This could lead to a mine fi re ifthe mine ventilation air was connected to a VAM abatement plant and the risks are left unmitigated.CorkyÆs is working with the mining industry to directly address these safety issues. CorkyÆs calltheir technology VAM RAB, which stands for ventilation air methane regenerative afterburner(VAM RAB). VAM RAB utilises the principles of a thermal oxidiser.This paper discusses fi ve independent layers of protection (ILPs) to fi rst stop methane reachingthe thermal oxidiser and secondly prevent the fl ame front from burning away from the VAMRAB. The test work completed or contemplated includes safety integrity level (SIL) assignmentto various vents, barriers and door systems to prevent a fl ammable mixture reaching the VAMRAB, proven rapid response methane monitoring sourced from the petrochemical industry, anddefl agration experiments to test the eff ectiveness of the passive geometry and active engineeringcontrols. These experiments and SIL assessments indicate that it is possible to safely connect theVAM RAB to a working coal mine.Further work is required to upscale the pilot safety work. Refi nement to the design is possible;for example improvement to safety duct controls once trialled at demonstration scale plus thermalenergy capture for power generation or other applications to provide heat. Nevertheless, thispaper shows how safety issues can be managed by a multilayer of protection approach usingvents, barriers and doors, and appropriate thermal oxidiser geometry."

Jun 1, 2012

By David Young

This paper presents tunnel design considerations for the SR75/282 Transportation Corridor Project in Coronado, California. The project is managed by the City of Coronado in cooperation with Caltrans and the US Navy and may include a one-mile long twin-tunnel section with two options: a 36.5 foot diameter twin-bored tunnel or a twin cut-and-cover box. The alignment crosses the Coronado Fault, and design provisions were needed at the fault crossing to maintain life safety and prevent rapid inundation of the tunnel in the event of fault rupture. These provisions are discussed along with considerations related to liquefaction and ground shaking. The project is currently in the planning stage with construction to start around 2012.

Jan 1, 2008

By P. Rosario

"Current industry practice for HPGR assessment and sizing relies on conducting a series of tests using pilot-scale machines with roll diameters of 700 mm to 1000 mm. Substantial amounts of sample are required for such pilot test programs, typically 1 to 10 tonnes of the sample is needed depending on the level of study and complexity of the resource. Collection of large quantities of representative samples during the early stage development is challenging and expensive, thus significantly hinders the HPGR technology from being incorporated into early-stage designs. A robust and reliable laboratory test is therefore needed to allow a fair consideration of HPGR for early stage projects. With support from the Canadian Mineral Industry Research Organization (CAMIRO), the NBK Institute of Mining Engineering at the University of British Columbia (UBC) developed a suite of Piston Press bench-scale tests that correlated to pilot and full scale HPGR operating information (Davaanyam, 2015; Davaanyam et al, 2015; McClintock, 2018). The Piston Press Tests (PPTs) are capable of assessing the HPGR technology at the scoping, pre-economic analysis (PEA), and pre-feasibility (PFS) stages of project development. This paper will briefly describe the theory on which the PPTs are based, and then presents a case study conducted for a copper deposit to show how the PPTs are being used for scoping and pre-feasibility level studies. Specifically, the PPTs are being used to provide information for preliminary sizing and selection of an HPGR and to assess the effect of ore variability on HPGR performance. The results are also applied to developing HPGR circuit designs and can be incorporated in simulation so that optimum design parameters can be selected.INTRODUCTION It is widely accepted that high pressure grinding rolls (HPGRs) offer a viable energy-efficient solution for the modern comminution flowsheet design. Table 1 summarizes selected examples of HPGR applications in the hard rock mining industry. The main benefits of HPGRs are energy savings which leads to lower operating costs, and its stable operating characteristics that can better cope with variations in ore hardness when compared to the conventional SAG mill-based comminution circuits."

Jan 1, 2019

By Michael J. Beus

This paper describes research conducted under the BuMines's Advancing Metal and Nonmetal Mining Technology Program, a major element being the application of new and improved technology to shaft design in deep underground vein-type mines. Two basic design parameters considered in shaft planning are configuration (shape) and ground support. The most common shapes are circular and rectangular. Ground support systems include concrete, timber sets, steel sets, rock bolts, and steel liners. The inherent advantages and/or disadvantages of various shaft designs such as ventilation and fire resistance, flexibility and ground support characteristics are well known. Circular concrete-lined shafts have minimal resistance to air flora and are virtually fireproof, an important consideration in deep hot mines. However, concrete does not yield significantly, and failure conditions and misalignment cannot be easily repaired. Timber-supported rectangular shafts predominate in the Coons d'Alene Mining District with its highly stressed and frequently heavy ground. The sets can be relieved and reblocked when out of alignment. However, the constant maintenance and repair requirements result in exposure to an inherently dangerous working environment combined with excessive operating costs. Obviously a dilemma exists--a circular, concrete-lined opening has many desirable features, provided it is strong enough to withstand the stresses involved. Rectangular, timber supported shafts have proven adequate in the Coeur d'Alenes; however, the implication of increased maintenance and repair requirements on ever-deepening shafts in this district and other similar areas will be an important design consideration in the future. This paper, then, presents shaft-configuration and ground-support guidelines to help remove some of the uncertainty concerning the stresses to be encountered in typical deep vein mining areas.

Jan 1, 1976

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

2. Preliminary Study - Initial Probing 2. 1 Introduction Initial probing of the mine passage is required prior to the emplacement of the sealant material or deployment of the seal checker system. Factors which are of interest in sealing and checking include a. size and condition of the mine passage b. location of the borehole with respect to the ribs c. the presence of water flows d. the proximity to an intersection The importance of each of these factors depends strongly on the sealant material. Because the sealant material had not been selected at the time of the initial probing study, a broad survey of probing techniques was conducted. The capabilities and limitations of each technique as they applied to probing through the borehole were identified. To facilitate this comparitive evaluation, Table I was prepared which lists all passage conditions which might affect the emplacement of sealant material in the passage. The most satisfactory techniques for observing each condition of interest are listed together with the effects of the observation on the sealing operation. Table II summarizes the environmental conditions likely to be encountered in the passage being probed and the physical

Jan 1, 1973

By R. G. B. Pickering

Resue mining was practiced extensively in the East Rand in the first half of this century. The obvious benefits were that a higher grade of ore was trammed to the surface. The disadvantages were slow rates of face advance and an extremely labour-intensive method of mining. A collaborative effort by personnel from Avgold?s Target Gold Mine and Sandvik Tamrock has resulted in the design of a method of resue mining which can be totally mechanized. The purpose of this paper is to describe the methodology used and the proposed new mechanized resue mining method.

Jan 1, 2000

By E. Salinas Rodríguez, I. Rivera Landero, E. G. Palacios Beas, J. Hernández Ávila, E. Cerecedo Sáenz, M. A. Mesinas Romero, M. I. Reyes Valderrama

For this study, a sample of 5 g of copper powders obtained by grinding printed circuit boards of computers fixe to 50 mesh (270 μm) according Tyler® series was used. This sample was wholly characterized by XRD, SEM–EDS and AAS. The leaching medium used wasO2S2O3 2. From the evaluated variables it was obtained an apparent order of the reaction of n = 2.34 s−1, whereas according the effect of partial oxygen pressure it was obtained an apparent order of reaction of n = 0.9516 and the activation energy of system was of 6.5 kJ mol−1, the results so achieved suggest a transport control to the solid–liquid interface. Under certain work conditions such as: S2O3 2 ¼ 0:5M, 500 mL, 750 min−1, P/PO2 = 1 atm, 338 K, 5 g of sample and 9000 s of reaction time, it is possible get up to 97.35% of leached copper.

Mar 1, 2017

By Jie Li, Zhongliang Tian, Xun Hu, Kai Zhang, Yanqing Lai, Hongliang Zhang

The Al-Sc Alloys show many advanced properties for a wide range of engineering applications. But the metal Sc must be added into the metal Al in the form of the Al-Sc master alloy, which is usually produced by the thermal reduction process. In this paper, the decomposition voltages of Sc2O3 and Al2O3 in Na3AlF6-K3AlF6-AlF3 melt were calculated based on the Nernst equation. And the Al-Sc master alloy was prepared in the melt at 950°C by electrolysis. The results show that the Al-Sc master alloy can be prepared by the co-deposition of Sc3+ and Al3+ at the cathode if the concentration ratio of Sc2O3 to Al2O3 in the melt is more than 2:1 under the condition of the aluminum electrolysis. SEM and ICP analysis of the product indicates that the Al-Sc master alloy is made of the phase Al and the phase Al3Sc.

Jan 1, 2016

Development of aggregate resources for use in structural concrete has been encouraged in Japan to support infrastructure improvement and national land conservation. Natural aggregate is a valuable resource necessary for sound economic development, and its importance is growing. After completion of aggregate mining projects, planting and afforestation are implemented. But sandy soil in excavation sites is not optimum for the growth of vegetation, and many years are needed before forests are restored. Planting techniques should be improved to support efficient reforestation in a shorter period of time. For this purpose, problems hampering growth of vegetation must to be solved through application of physical and physicochemical techniques to ensure that the environment and the ecosystem will be conserved in project sites.

Dec 6, 2010

By A. Galvan

High rate compressible media filter (CMF) tests produced exceptional total suspended solids (TSS) removal at hydraulic loading rates ranging from 97.8 to 122.2 m/h. The compressible media is manufactured from a robust resin fiber that can withstand low pH and temperatures up to 149 °C. The media porosity can be varied by applying compression onto the media. At 40% compression, the CMF can remove particles greater than 4 μ. Three synthetic test-samples were generated by Hazen Research Inc., (Golden, Colorado) to simulate the copper Pregnant Leach Solution (PLS), Raffinate and Electrolyte solutions used for the testwork conducted at their facility. The preliminary results showed that the CMF was very effective in removing TSS without the use of chemical conditioning from the above test-solutions with efficiencies of 98%, 97%, and 96%, respectively. Given the remarkably high hydraulic loading rates, the industrial equipment footprint would be minimized appreciably over conventional clarification and alternative filtration systems.

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been studied on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27° between each tuyere, and five side tuyeres with an angular separation of 22.5° or 27° between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By I. Cameron, S. Ramjee, A. M. Garbers-Craig

The cause of reduced workability and increased ageing of a blast furnace taphole clay was examined. The investigated taphole clay contained 60 mass% alumina, with phenol-formaldehyde resole resin and liquid pitch serving as the binder system. The workability and Marshall extrusion pressure of the as-manufactured clay samples were evaluated to assess the extent of ageing of the clay. The wettability of all the raw materials was investigated to confirm compatibility between the dry raw materials and both the resin and liquid pitch, while the dry raw materials were analysed using XRF, XRD, and SEM-EDS. The characterisation of the resin and liquid pitch, as well as an analysis of their interaction, was performed using viscosity measurements, Fouriertransform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The analyses confirmed a chemical interaction between the resole resin and liquid pitch, where the chemical structure of the resole resin changed when mixed with pitch, preventing the typical curing behaviour of the resin. Upon ageing of the resin-pitch mixtures, the resin underwent premature cross-linking, causing the curing process to initiate at lower temperatures, i.e., earlier onset of curing. This premature cross-linking was likely due to secondary amines present in the liquid pitch, which acted as a catalyst for the curing process of the resin. This reduction in curing temperature after ageing was confirmed by an increase in binder viscosity, which was identified as the primary cause of reduced workability, accelerated ageing, and increased Marshall extrusion pressure of the taphole clay.

Jul 23, 2025

Over 800 mines have closed in Australia in the past 25 years. This paper summarizes the data obtained from those closures and includes all Australian States and Territories and all commodities, including metalliferous, coal and industrial minerals. Twenty five percent of the mines closed due to resource exhaustion or depletion; 24% due to high costs, price drops, or declining grades; 8% due to open pit resource depletion (but with underground reserves remaining) or underground reserves depleted (but plans to open cut remainder) and 7% due to receivership or voluntary administration. The environmental, social and economic impacts of these closures are also significant and include acid mine drainage and impact on mine employees. An understanding of the causes of premature mine closure will better equip mining companies and governments to better manage future mine closures, wherever in the world the mines are operating.

Jan 1, 2007

The most appropriate technology needs to be applied to premining geological investigations to achieve reliable data for predictions of geological conditions ahead of mining. The paper describes the application of various investigatory techniques in BHP's Illawarra Collieries which are used to provide reliable assessments of structure, the nature of the coal and surrounding strata,, and the fluids contained in the strata. The techniques used include surface seismic, in-seam seismic, borehole drilling, electromagnetic and aeromagnetic surveys, hydrogeological investigations and in-mine mapping. The results of various case studies are presented as examples of the application of techniques.

Jan 1, 1988

By J. C. Johnson

High-grade ore found in a shaft pillar at the Homestake Mine prompted a request for a Bureau of Mines study to determine if selected areas of the shaft pillar could be mined without jeopardizing the shaft. The design approach was to perform a finite-element study of the shaft pillar. Plan view and vertical sections were developed using two-dimensional, elastic, plane strain assumptions. Input into the model consisted of in situ stress measurements geologic mapping rock mass properties, and previous mining history. Results from the study indicated that ore-beating sections of the shaft pillar could be removed within the displacement tolerances acceptable for the shaft. Homestake engineers, using the results of the finite-element study and considering other factors, have designed and are beginning to mine the shaft pillar.

Jan 1, 1989

By Thomas Fraser

"El siguiente estudio señala las recomendaciones para la preparación de las antracitas del Santa de la mina ""La Limeña"", así como las modalidades para determinar los efectos de la ""trituración"" diferencial y ""maceración"" en agua del carbón del tipo ""Limeña"". El resultado de estas pruebas en Bradford, mostraron que el carbón de ""La Limeña"" es adaptable para la ""trituración"" diferencial. Dicho mineral es mucho más blando que el relave, de allí que una gran proporción del carbón limpio disponible permanezca en su tamaño lógico inferior a 5/16"" producido en la extracción y manipuleo. Así también el tratamiento experimental de los tamaños mayores en una planta del tipo Bradford se divide en dos: el primero refiere un relave ""duro "" de tamaño mayor, que contiene una pequeña cantidad de carbón limpio, brillante y fácilmenteescogido a mano; y lo segundo, es una mezcla de tamaño inferior, de ""middling"" y carbón para lavado posterior."

Jul 20, 1955