Search Documents

By William H. Walton, Clyde N. Baker Jr., Darren S. Diehm

"A 51-story concrete core and steel frame commercial office tower was recently constructed on the site of the former US Gypsum building in downtown Chicago, Illinois, USA The structure foundation reused several caissons from the demolished US Gypsum building supplemented with new belled caissons bearing on silty clay hardpan. Extensive in-situ pressuremeter testing was performed during the geotechnical investigation to determine allowable bearing capacity and better estimate building settlements. Problems during foundation construction along the south side of the building frame required remediation of two caissons. One caisson was supplemented with micropiles, while the second caisson was abandoned and replaced with a straight-shaft rock socketed caisson. To determine the effectiveness of the repairs, the building foundation settlements were monitored during construction.IntroductionIn 2001, The John Buck Company began development of a new office tower at the southeast corner of West Monroe Street and South Wacker Drive in Chicago, Illinois. The site was formerly occupied by the 18-story US Gypsum (USG) building. Mr. Clyde N. Baker, Jr. (Senior Principal at STS Consultants, Ltd .) served as the foundation engineer for USG which was completed in 1962. The building was founded on a forest of belled caissons bearing at elevation -56 Chicago City Datum (CCD). For reference, the ground surface at Upper Wacker Drive is approximately elevation +20 CCD. The bearing material was a hard silty clay, locally described as Chicago Hardpan. The foundation caissons were designed using an allowable bearing pressure of 16 ksf (766 kPa). In 1996, the USG superstructure was razed, and the three-level basement was converted to an underground parking ramp.South Wacker DevelopmentThe 51-story high-rise building was completed in 2005 with a structural height of 681 feet (208 m), and an internal space of more than 1,000,000 square feet (93 ,000 square meter). The typical floor size is 27, 700 square feet (2, 570 square meter). Renderings of the building are provided in Figures 1 and 2. The largest single tenant is the accounting firm of Deloitte & Touche, which occupies roughly 45% of the building space with over 3,000 employees."

Jan 1, 2005

By J. W. Bawden, J. Nantel

"The mine operator has two prime objectives when he operates a mine: (l) the mine must be safe, and (2) the mine must operate with the lowest possible costs. The operator constantly faces a dilemma; if he is over cautious with regard to safety, his costs may be very high, and if he is over-zealous in trying to reduce costs, the safety of his operation may be jeopardized.Modern bulk mining methods rely heavily on high productivity non-entry stoping techniques (e.g. open stoping, VCR, etc.). Such techniques have the advantage of removing the operator from the active and sometimes dangerous mining face and ofminimizing costly development. On the other hand, this generally results in a certain loss of flexibility in following irregular ore-waste contacts. If stopes are opened too large and/or are inadequately supported, severe dilution with resulting escalating costs usually results. If initial access drift support is inadequate for latter mine induced stresses high rehabilitation costs may also be incurred.Optimization of stope dimensions should logically occur as part of a general mine rock engineering program, within the over-all mine planning context. The same program should help highlight those areas where drift rehabilitation may be a problem.Whenever successful mining is performed, rock engineering is being applied, either by design or by chance. The cost implications of planned practical rock engineering as an integral part of mine planning and design can be very significant to the ultimate mining ""bottom line"". At Noranda Minerals Inc. allowable stope dimensions are derived using a combination of numerical stress analysis and empirical design techniques. This paper discusses the use of the above techniques and their limitations as tools for rock mechanics based stope dimension optimization. The potential cost implications of such design efforts within the general mine planning context are also addressed."

Jan 1, 1989

By D. Milne, P. Germain, G. Sauriol

"The practical determination of optimum stope geometry has, until recently, been an art relying primarily on experience at a given operation. Due to the complex and variable nature of rock masses in situ, stopes are often designed either very conservatively, resulting in excess development, or non-conservative resulting in excessive dilution and, in some cases, in loss of ore reserves.The Geomechanics group of the Mining Technology Division, Centre de Recherche Noranda, uses a combination numerical modelling and empirical design techniques to optimize allowable stope geometries. The above methodology allows the optim ization of stope geometry for varying rockmass classifications within an operation or between different operations. Such techniques require the development of a thorough geotechnical database at each operation and are best used when calibrated to the specific operation through back analysis.This paper discusses the above optimization techniques in light of specific examples from the Noranda Group. The design methods, limitations and results are discussed.INTRODUCTIONMine design has traditionally referred to production planning, general facility layout, (i.e. ore passes, crusher stations, main haulage drifts, etc.) and ventilation design. The dimensioning and sequencing of the stopes and pillars, however, has been almost solely based on trial and error and precedent practice.More recently, numerical stress analysis has received much more attention as part of the design process. It is common now at many operations to look at the effect of proposed stope layouts and sequences on stress redistribution through the surrounding mine workings. Through calibration of actual stope and pillar behaviour in situ, one can then relate the model predictions to support requirements, safety problems, etc."

Jan 1, 1989

In practice a sampling solution is a compromise of many requirements: the sample should be representative; the sampling system should also be reliable, less than 95 per cent availability restricts the use of the assayed sample for process control purposes; no sample is the worst sample, and investment costs and installation space/layout are frequently a restriction. For instance, online X-ray analysers for process control introduce a delimitation error by the nature of X-ray physics. Thus only in special cases a relative accuracy better than three per cent relative, as one standard deviation, is achieved. A sampling system for process control needs not to be, as representative, for so many sample properties, as one for composite laboratory analysis samples. Sampling system maintenance is also an important issue. There are many sampling systems in the industry which have been difficult to maintain and are in disuse for lack of resources or incentives to keep them running. Pierre Gy developed the most generally accepted sampling theory. One of the main principles is that all particles in a one-dimensional process stream should have equal chances of being included into the sample. A correctly designed and operated transversing cutter comes close to this goal but has limitations in temporal representativity. For slurries an acceptable solution in many cases is to use a fixed vertical cutter(s) in a position where the slurry is well-mixed by turbulence and other means. For online analysis, reliability problems are mostly related to faulty design or installation of the piping system to the analyser. Properties of material processed, process flow sheet and piping details before and after the sampler have to be taken into account when deciding on which sampling arrangement is appropriate. Guidelines and some solutions to these issues are presented in this paper.

Mar 1, 2010

By M. M. K. McCrank

"PRACTICAL SAMPLING TECHNIQUESIt is important to achieve reliability when sampling heterogeneous materials where there is a difference in composition, and non random distribution of the constituent particles. Throughout the design, construction and installation of sampling systems it must be borne in mind that the sampling point must be capable of:-allowing each particle in the stream an equal opportunity to be sampled.-accepting and collecting as large a volume or mass of material as necessary to satisfy the requirements of particle counting statistics.-establishing a sampling plan so that the sample is representative of the whole to a defined standard of accuracy.Design ConsiderationsFactors that may influence the design of the sample point include:-the mass, or volume flow rate of the material being sampled-the size and shape of the material or flowing stream-the physical condition of the material being sampled (i.e. temperature, wetness, size consist, density).-the chemical composition of the material being sampled -the location of the sample point and the space available for installation, extraction, reduction where necessary, secondary sampling, and return of the sample rejects downstream.-whether the process to be sampled is in an existing plant or one yet to be designed and built.-ease of access for servicing and maintaining the equipment.-whether the sampled material must be collected continuously or intermittently.-whether an existing sampling method is likely to be adequate or whether a new technique has to be developed."

Jan 1, 1989

By Bianca Foggiatto, Marko Hilden, Malcolm Powell

"Since the introduction of the concept of flexible circuits (Powell and Bye, 2009), it has been further developed and refined to the definition of ‚FlexiCircuits leverage ore variability to maximise resource utilisation?. The focus of flexible circuits is to investigate processing options that provide extra capacity through sophistication rather than scale. This requires a combination of smart ore characterisation, economic modelling and innovative processing plant design. Flexible circuit design can reduce energy requirements through gangue rejection or progressive ore upgrade; and increased robustness and controllability by leveraging off ore variation. Each rock type, as characterised through Geometallurgical ore modelling, may be processed more efficiently by individually optimising processing paths. The objective of FlexiCircuits is to transform the processing capability of comminution and concentrator plants - targeting step change in performance through integrating a range of interrelated improvement opportunities. Considerable effort has been applied to developing the modelling and simulations tools required to develop and demonstrate the potential of this concept. This paper presents a practical application as a test case. A realistic application of flexible circuits is provided through a conceptual circuit design of an iron ore processing plant. It is simulated as a multi-component feed with a range of new models in the researcher’s Model Developers’ Kit (MDK) to trial the ability of different circuit designs to respond to variable ore and quantifying the potential of these circuits to transform processing capability of variable ore feed. The outcomes of the simulations are presented and discussed, providing a practical demonstration of the level of modelling and simulation required and the potential of flexible circuit design."

Jan 1, 2014

By Walter G. Kutschke

Four significant soil nail wall projects in the eastern United States were recently completed with a combined area of 175,000 square feet of finished shotcrete surface. These projects required the use of innovative design and construction methods in order to address various challenges, including slide-prone back slope materials, perched water, highly erodible rock materials, curved wall alignments, very tight construction tolerances and unexpected subsurface conditions. Special focus is given to issues such as bench excavation, soil nail installation methods, shotcrete mix design, anticipated shotcrete quantities, shotcrete nozzlemen qualifications and weather conditions, in order to provide a lessons-learned database for future soil nail wall design and inspector considerations. These projects also underscore the importance of design engineer and soil nail wall contractor qualifications as well as effective communication with the owner.

Jan 1, 2007

By S. D. Dladla, S. Ramsamy

The majority of the tailings dam operations in South Africa will be required to comply with the new Global Industry Standard on Tailings Management (GISTM) within the next one to three years, depending on the dam classification and the requirements of the respective investors and insurers. With up to 72 auditable requirements, the implementation of the Standard needs careful planning and prioritization. This paper focuses on the practical steps to GISTM compliance for tailings facilities in operation in South Africa. The discussions are based on current practices, South African regulations, and industry standards requirements. The possible changes in dam classifications and the associated requirements are presented.

Jun 2, 2022

By J Wesseloo and Y Kim, Y Potvin, G Mungur, D Grant

At the previous MassMin conference held in Sudbury in 2012, the authors proposed a new framework going beyond dilution and equivalent linear overbreak sloughing (ELOS) for stope reconciliation in relation to the planned stope design. More specifically, the new process investigates performance outcomes including rock overbreak (OB) and fill overbreak (FOB), rock underbreak (UB) as well as geomechanical and operational aspects such as blasting, fragmentation and other production data.Based on the findings of the original 2012 study, a comprehensive data gathering program has been undertaken involving design and reconciliation data from 43 stopes mined between September 2012 and October 2014 at BHP Billiton’s Olympic Dam (OD) operation. The new database structure was based on four types of data:stope definition and performance datastope geometrygeotechnical parametersoperational parameters.The new database allows a more in-depth investigation of stope performance. It is now possible to quantify and analyse UB and OB performance from each wall individually as well as the crown. In this paper, the influence of several parameters on recent stope performance at OD is analysed. The underlying reasons for stope wall performance outcomes are discussed in this paper.CITATION:Potvin, Y, Grant, D, Mungur, G, Wesseloo, J and Kim, Y, 2016. Practical stope reconciliation in large-scale operations part 2, Olympic Dam, South Australia, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 501–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Shane McDonald

Australia produces approximately 84 million tonnes of coal per annum from 30 longwalls in New South Wales and Queensland, operating at an average depth of around 300m. Industry trends and expectations place increasing emphasis on the reliability of these operations; for example, the current average face width is 245m and this is expected to increase to approximately 270m by 2010. In recent years, Beltana No.1 Mine has consistently been Australia?s highest longwall producer, with ROM output of 7.2Mt in YEJ2007. Strata management has become a key feature of the operation of Australia?s longwall mines, as a tool to manage variances in the geotechnical environment. This involves an understanding of the impacts of the geotechnical environment on ground behaviour and the implications for mine design, stability and associated support, interaction and horizon selection. The anticipated ground control impacts of these factors form the assumptions that drive the format of plans specifying both triggers and actions, with quantified, monitoring-focussed experience used to refine the plan in a continuous improvement (ie ?plan-do-check-act?) process. This paper summarises the Beltana No.1 Mine strata management methodology and experience to-date.

Jan 1, 2008

By Keith Heasley

As part of the initial investigation and validation of a new boundary-clement formulation for stress modeling in coal mines. the underground stresses and displacements at two multiple-seam coal mines with unique stress problems are modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and non-linear seam materials can he used: and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geo-mechanics based on previously observed stress conditions at the mine. For this calibration process. a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems abead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses, and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 1, 1998

By C. L. Tang

Parts of the wastewater are reused directly and the rest moderately purified and reused, so the utilization rate of wastewater of the whole processing plant reaches 100 percent. At the same time, beneficiation indicators have been improved stably, and great economic and social benefits have been achieved.

Jan 1, 2014

By Keith A. Heasley

At this point in time, approximately 800 M tonnes (880 M tons) of coal are mined each year in the United States. Forty percent of this coal or approximately 320 M tonnes (350 M tons) is taken from underground coal mines, and from this subtotal 16% or 50 M tonnes (55 M tons) is from longwall panels (1). If, for the sake of argument, an aver- age extraction thickness of 1.5 m (5 ft), an aver- age extraction ratio of 50 percent and an in situ density of 1360 kg/ms (85 lb/ft3) for this coal are assumed, then the 320 M tonnes (350 M tons) of underground coal translates to over 310 km2 (76,000 acres) that is undermined each year. Con- sidering that the total U.S. production of under- ground longwall coal to date is approximately 345 M tonnes (380 M tons), then a total of approximately 165 km2 (41,000 acres) (considering 100% extraction) has been directly undermined by longwall coal production in the United States. If the angle-of- draw is considered, the total area affected by longwall subsidence in the United States is probably twice the above value or 330 km2 (82,000 acres) . In the future, a number of other miscellaneous factors seem likely to multiply the number of potentially damaging situations that occur due to longwall coal mining. First, the overall production of coal in the United States is expected to gradually increase. This factor is further com- pounded by both the fact that the percentage of the overall production due to underground mining is bound to increase, since the vast majority of U.S. reserves (68%) are only recoverable by underground methods, and the fact that the percentage of the underground production of coal that is recovered by longwall mining is drastically increasing (1). Finally, as the nicest underground reserves are depleted, the remaining reserves will tend to be deeper, which increases the affected surface area, and under denser population concentrations, which increases the likelihood and severity of possible damages. Overall, considering the number of factor which are biased towards increasing the amount of undermined acreage, it appears that there must certainly be a corresponding increase in the number of possible damaging situations due to longwall-induced, ground subsidence.

Jan 1, 1986

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory are developing ways to protect the health of miners. Part of that effort is devoted to improving the air quality in underground stone mines by developing ventilation techniques that can be used in these types of operations. The air quality in these large opening nonmetal mines can be significantly improved by using diesel particulate matter (DPM) controls along with sufficient ventilation quantities to remove contaminants. Practical methods of ventilating these underground stone mines can be accomplished by using mine layouts that course and separate ventilation air through the use of stoppings. The design, construction, and maintenance of effective stoppings in large openings have been a real challenge to mine operators. Several different types of stoppings have and can be used for this application. The choice of stopping design, material used, and construction techniques should be dependent upon a number of factors such as the intended life and effectiveness desired.

By M. Hakala

A computer program was developed to simulate transient strains and stresses during an overcoring in the situ stress measurement. The solution is based on superpositioning of elastic stresses. The measured strains can be compared with the calculated ones to check if the measured transient behaviour is accordant with the interpreted in situ state of stress. If not, the in situ state of stress can be calculated based on any transient or final strain values. The transient stresses can be compared with the strength envelope of intact rock and thereby estimate the core damage potential. Technically, the developed code fulfilled all the objectives, and the numerical error was found to be less than 5%. The basic idea can be applied also for different overcoring probes with minor modifications and recalculation of stress tensors. The analysed case studies showed clearly the advance of having an objective and practical quality control method to study the reliability of the in situ stress measurement data. The study was set up and funded by the nuclear waste management companies Posiva Oy ( Finland ) and Svensk Kärnbränslehantering AB ( Sweden ). Un programme informatique a été développé pour simuler des tensions et des contraintes passagères pendant la mesure in situ de contrainte de surcarottage. La solution se fonde sur une superposition de contraintes élastiques. Les contraintes mesurées peuvent être comparées avec celles calculées pour vérifier si le comportement passager mesuré correspond à l'état de contrainte in situ interprété. Sinon, l'état de contrainte in situ peut être calculé à partir de n'importe quelle valeur de contrainte passagère ou finale. Les contraintes passagères peuvent être comparées avec l'enveloppe de force de roche intacte et ainsi il est possible d'évaluer le potentiel de dégâts au noyau. Techniquement le code développé a rempli tous les objectifs, et le taux d'erreur s'est révélé être inférieur à 5 %. L'idée de base peut être appliquée aussi pour différentes expériences de surcarottage avec des modifications mineures et le recalcul de tenseurs de contrainte. Les études de cas analysées ont montré clairement l'avantage d'avoir une méthode de contrôle de qualité objective et pratique pour étudier la fiabilité de données de mesure de contrainte in situ. L'étude a été fondée et financée par les sociétés de gestion de déchets nucléaires Posiva Oy (Finlande) et Svensk Kärnbränslehantering AB (Suède). Es wurde ein Computerprogramm entwickelt, um Transient-Beanspruchungen und Spannungen während eines Überentkernens in situ-Spannung-Messung zu simulieren. Die Lösung beruht auf Superpositionierung von elastischen Spannungen. Die gemessenen Beanspruchungen können mit den berechneten Daten verglichen werden, um nachzuprüfen, ob das abgemessene Transient-Verhalten mit dem interpretierten in situ-Zustand der Spannung übereinstimmt. Wenn nicht, kann der situ-Zustand der Spannung auf irgendwelchen Transient- oder endgültigen Beanspruchungswerten berechnet werden. Die Transiet-Spannungen können mit dem Stärke-Umschlag des intakten Felsens verglichen werden und dadurch ein Kernbeschädigungspotential kalkulieren. Technisch erkannte der entwickelte Code alle Ziele und hat gefunden, dass die numerische Fehler weniger als 5 % waren. Grundsätzlich können auch verschiedene Überentkernen-Untersuchungen mit kleineren Modifizierungen und Wiederberechnung des Spannung-Tensors angewandt werden. Die analysierten Fallstudien zeigten deutlich den Fortschritt, objektive und praktische Qualitätskontrollmethode zu haben, die Zuverlässigkeit in Situ-Spannung-Messung-Daten zu studieren. Die Studie wurde aufgestellt und durch Atommüll-Management-Firmen Posiva Oy (Finnland) und Svensk Kärnbränslehantering AB (Schweden) finanziert.

Jan 1, 2003

By Bradford F. Townsend, Colin R. Speers

INTRODUCTION This is the first in a series of papers addressing practical tunnel lining design. The format for this and future papers is to present a particular topic and support the presentation of the guidelines by the practical application of a case history. The primary intent is to provide guidelines for the geotechnical and structural design of tunnels where the tunnel size and/or ground conditions dictates that systematic support of the excavation is required following each increment of excavation. This method of tunneling is commonly referred to as Sequential Excavation and Support(SES) and is also commonly termed the New Austrian Tunneling Method (NATM) The authors developed the design guidelines from experience gained over the past two decades during the design and construction of several major railway, highway and water-transfer tunnel projects in Africa and Asia. During this time it has been possible to compare the performance of the as-constructed structures to the predicted performance as given by the design process. Excavation was typically carried out in widely varying ground conditions (weak-bedded rock, jointed hard rock, and soil-like poorly cemented rock with groundwater). It is therefore intended that the design guidelines could be applied, in general terms at least, to any tunnel excavated in any ground mass condition with any ground material type (hard rock, soft rock, bedded rock, soft ground, and soil) with or without ground water. This first paper is an introductory paper that defines the scope and a brief outline of the design issues that may be presented in detail in later papers. What is design? It may be thought of as any rational/verifiable/justifiable process whereby a concept is transformed into information that can be used to bring the concept to reality. In the case of a civil structure, design may be defined as that process, which is documented and can be audited, that determines information such as the shape (form) of the structure, the dimensions (size) of the structure, the thickness and strength of structural members that comprise the structure, etc. This information can be used to compute the time, money and resources required for

Jan 1, 2005

By Hempenstall J, English W

Mine management has a responsibility under the various acts of state parliaments for the adequate ventilation of existing workings. It also has a need to plan adequately for the ventilation of proposed workings. Future workings alternatives have become progressively more complex and ventilation planning of the various possibilities must be undertaken within an atmosphere of rapidly changing market circumstances, etc. Any non-optimal solution will prove more expensive than necessary on both capital and cost bases. Clearly these increasing and alternative ventilation demands of coal mines in Australia have multiplied the work load of ventilation engineers. Management in general has for some time been aware of the advantages of using computers for commercial applications such as payroll and stores inventory. However, while the hand held calculator has replaced the traditional log tables and slide rules for smaller engineering calculations, the larger digital computer has not made the same

Jan 1, 1983

By E Jak, J Chen, B Hogg, S Nikolic, S Nicol

The quantity of post-consumer ‘waste’ materials generated each year is rapidly increasing. These materials can contain significant quantities of critical metals and present an environmental challenge if landfilled. The ISACYCLE™ technology is a proven solution for the processing of these materials. In the ISACYCLE™ furnace, the post-consumer materials are processed to recover energy along with any contained critical metals, in the form of a base metal alloy or matte. In addition, a clean aggregate (slag) is generated, which has the potential to be used for a range of applications in the construction industry. This slag is commonly based on a fayalite slag but is modified to manage the complex feed. This paper will review the fayalite slag system and the theoretical modifications required for treating urban wastes. Slags from an ISACYCLE™ furnace processing urban wastes have been sampled and characterised. The chemistry of these samples will be reviewed and compared to the expected theoretical modifications required.

Jun 19, 2024

Most coal mines in Chongqing Area are highly gassy mines and liable to outburst of coal cnd methane. In order to harness mine environment and raise the Prodction capacity, methane predrainage is generally taken as a main preventive measure against outburst by all mines. In the recent ten years, the drainage volume per year has increased from 38.25 million m3 to mote than 100 million m3 with a volume over 12 m3 per tome of coal. In some mines, the draining rate is approaching to 50 percent, the rate in mining districts is up to 60 to 70 percent. The predrainage volume accounts for one fourth of total drainage volume. All these have effectively prevented the occurrence of coal and methane outbursts.This is the current situation of methane predrainage in coal mines in Chongqing area, the methods of predrainage to prevent outbursts and related parametres comprise:1. methods, technologies, supervision and effect of predrainage in different geological and mining conditions,2. the change of methane parametres pre-and post-drainage and the analysis of the effect of methane predrainage to prevent outbursts, and3. ways to improve the effect of methane predrainage.Thus the safety, reliability and production of Changqing Coal Mines will be enhanced.

Jan 1, 1991

In China, thin coal seams are rich in resources but are technically challenging. The mineable reserves in these seams account for 20.4% of the total coal resources, while the current production accounts for only 10.4% of the total annual production. Characteristics such as narrow mining space, low level of mechanization, poor working environment, and high cost of mining, restrict the development of mining safety and efficiency. Recently, fully mechanized mining technology has developed rapidly for thin coal seams, the level of yield and efficiency has reached or exceeded the international standard, and some state-owned key coal mines are considering automation of their mining process. In thin coal seams with hard stone bands that contain concentrations of pyrite, a specialized software, LS-DYNA, is used to calculate the rational blasting parameters that are used in the deep-hole pre-splitting blasting. Using this method the hard stone bands are fractured effectively, and hence increasing the coal productivity. In addition, mining advance rate were increased by enhancing the level of fully mechanized equipment and safety improved by increasing gas drainage from the gas outburst prone seam located some 7 m below the coal horizon. At present, thin coal seam mining technology faces many challenges, including the low level of equipment automation, the low advance rate in mixed coal-rock ground, and the large number of the mine personnel underground. By lowering the labour intensity and improving efficiency through automation and other measures, more efficient working faces can be implemented in thin coal seams.

Jan 1, 2012