Search Documents

By D. G. Westlake

Levine has concluded that prismatic slip in titanium is controlled by two distinct thermally activated processes in the temperature ranges O° to 220°K and 220" to 300°K. We feel that his evidence is not convincing. He has drawn a curve through the plot of activation volume u* vs temperature T with a break at 22WK, Fig. 2. We believe that considering the possible experimental error apd the fact that there are only four points between 4° and 196°K, one could be justified to represent these points by the smooth curve we show as a solid line in Fig. 12. Levine believes that (8rf/aT)+ is discontinuous at 220°K, but he hints that he recognizes the possible doubt. We doubt seriously that the results shown in Fig. 1 indicate a discontinuity at 220°K. Certainly if he were justified in drawing a straight line through only four points on Fig. 2, we are even more justified in drawing straight lines through the seven points between 77" and 297°K on Figs. 1 and 3, because a straight line touches all seven of his circles. If his measurements of t were so precise that his decision to draw two curves in Fig. 3 is valid, then the experimental technique is deserving of further mention. We have drawn a smooth curve through the results in Fig. 3 and used this and the curve in Fig. 12 to obtain the values of shown in Fig. 13. Finding continuous is a contradiction of Fig. 4, which deserves comment itself. Levine obtained the solid circles in Fig. 4 using Fig. 2 and a smooth curve through the points shown in Fig. 3. We have replotted these solid circles in Fig. 14. We submit that there is no basis for his two straight lines (dashed in Fig. 14), and therefore have superimposed the curve that we believe is indicated. Certainly, there is reasonable doubt that a discontinuity in dH/dT exists at 220°K, even when one accepts Fig, 2. Furthermore, if one draws the straight lines indicated by least-squares treatments of the results presented as open circles in Fig. 4, their intersection is at about 196°K, not at 220°K as shown. Thus the alleged agreement between Figs. 3 and 4 with respect to "break" temperatures is not apparent. In Fig. 9, Levine has drawn a straight line very much different from the one indicated by a least-squares treatment. Obviously, he has done this because he recognized that H = 0 when T = 0. He is consistent in drawing the low-temperature curves in

Jan 1, 1968

By P. Marier, T. R. Ingraham

When cylindrical powder compacts of nickelous oxide (NiO) are heated in an equilibrated stream of SO3, SO,, and 02, in the temperature range 500°to 800°c, tlickelous suljate (NiSO4) is formed as an adherent layer on the oxide. The reaction is diffusion-controlled, with an activation energy of 13 ± 3 kcal per mole. When cylindrical powder compacts of NiSO4 are heated in a stream of dry nitrogen in the temperature range 1000 0to 11500C, NiO is formed at a well-defined interface between the sulfate and oxide. The interjhce migrates into the sulfate at a constant rate at a constant temperature and gas flow. The reaction rate increases with increasing gas flow and decreases with increasing partial pressure of SO3 in the gas stream. Resolution of the partial-pressure data with a Lang-itzliir Adsorption Isothern suggests that about 80 pct of the NiO interface is covered with SO3. The heat of adsovption is about 68 kcal per mole. The activation energy of the decomposition process is 61 ± 3 kcal per mole. MOST of the work reported on the formation and decomposition of nickel sulfate is related to thermodynamics.1-3 No quantitative work has been reported on the decomposition process. The only kinetic work reported on the formation is that by Fletcher and shelef.4-6 whose main purpose was to study the effects of alkali metal sulfate additions on increasing the rate of nickel sulfate formation. They found that, in the absence of an additive, only small amounts of sulfate were formed and the kinetic data were difficult to interpret. However, they suggested that the sulfa-tion of nickel oxide is a diffusion-controlled process for which the activation energy is approximately 17 kcal per mole.6 In this paper, both the formation and decomposition reactions will be examined; and based on the effects of temperature, flow rate, interfacial area, and partial-pressure of sulfur trioxide, mechanisms and activation energies will be suggested for both processes. EXPERIMENTAL Material. The nickel source material used in all experiments was Baker and Adamson Reagent Grade NiSO4. 6H2O, for which the following analysis was supplied by the manufacturer: C1, 0.001 pct; NO3, 0.005 pct; Co, 0.02 pct; Cu, 0.005 pct; Pb, 0.002 pct; Fe, 0.001 pct: insol, 0.005 pct. The anhydrous sulfate was prepared by heating the hydrate at 420°C in a muffle furnace for 5 hr. Nickel oxide was prepared by decomposing the sulfate at 950°C over a period of 10 hr. Method. The technique used for measuring the rates of formation and decomposition was developed earlier in these laboratories.7-8 The method is based on the observation that the kinetic parameters of a reaction can be established in a flow system, with specimens prepared by compacting powder to a uniform pellet shape. The results are identical with those established with solid polycrystalline specimens or single

Jan 1, 1967

By B. W. Roberts, V. A. Phillips

A copper alloy containing- 25.5 at, pct Zn and 19.0 at. pct Ni, which was previously found to show an anoma1old.s hardening effect on quenching- from 600 "C and aging- at 400oc, has now been examined by neutron diffraction. No evidence of long-range order was found. The aged sample showed diffuse scattering- consistent with clustering. The anomalous hardening effect is now attributed to lattice strains caused by clustering rather than (long-range) order hardening. SOLID-solution Cu-Ni-Zn alloys (the commercial 'nickel silvers") have been reported to show anomalies in: change of resistivity on cold working,1-6 temperature coefficient of resistance,2-12 resistivity at low temperatures,13,14 parameter (vs temperature),2"4 calorimetric data,2,4 specific heat,15,16 dilation,2-4 and elastic modulus.17 The structure responsible for the anomalies is produced by annealing typically near 400°C and is rather loosely referred to as the ('K-Zustands" (K state), a term coined by Thomas1' who apparently meant simply that the arrangement of atoms on the sites deviated from that expected statistically. Thomas proposed that the K state occurred in a variety of (solid-solution) alloys such as Cu-Ni-Zn, Ni-Cr, Ni-A1, Ni-Cu, Fe-A1, and Fe-Si and is recognized because its formation is strongly temperature-dependent and results in an increase in electrical resistance which can then be decreased by cold working. Later workers on ('nickel silver" have interpreted the K state variously as short-range order, long-range order. or a combination. The present work was prompted by the discovery by Phillips and Jones19 of a substantial hardening effect when an 18 pct "nickel silver" alloy which is fairly close to the Cu2NiZn composition, was reheated in the range 150" to 450 C after previously quenching from 600°C or, alternatively. was slow-cooled from 600°C or above. The phenomenon was attributed to (long-range) order hardening. Due to the similarity in the atomic scattering factors of copper. nickel, and zinc atoms, the ''nickel silvers" are unfavorable for X-ray diffraction studies aimed at detecting ordering. Nevertheless Bialas et a1.,20 using a powder sample containing 47.96 wt pct Cu, 24.03 wt pct Ni, and 27.98 wt pct Zn, slow-cooled from 400" to 200°C taking 500 hr, observed weak super lattice lines. Further unpublished work" using an anomalous dispersion X-ray technique indicates that zinc atoms are regularly ordered at the corner points of the lattice cell, while the nickel and copper atoms are statistically distributed on the remaining sites. Köster 17 also observed X-ray superlattice lines, for example, in an alloy containing 43.5 wt pct Cu, 28.6 wt pct Ni, and 27.9 wt pct Zn superimposed on the basic fcc cell with a = 3.62 kX. He proposed a Cu3Au-type superlattice with the Ll2 structure in which the A sites were statistically occupied by copper and nickel atoms and the B sites by zinc. He adds that substitution must be possible so that zinc atoms partly occupy A sites. Below about 35 pct Cu, Koster had some evidence for a CuAu-type superlattice with the Llo tetragonal fcc structure with a = 3.82 kX, c/a = 0.88 which could be preserved by quenching. This is suggested17722 to correspond to CuNiZn. While the present work was in progress Hirabaya-shi et a1.23 made an independent comprehensive neutron-diffraction study of a single crystal containing 50.05 at. pct Cu, 26.57 at. pct Ni, 0.25 at. pct Mn, 0.13 at. pct Fe, balance zinc. The presence of manganese and iron is surprising since the crystal was supposedly grown from high-purity metals. The homogenized crystal showed evidence of long-range ordering after an anneal of 5 months at about 300°C. Three possible crystal models were proposed. A curious feature of their results23 is that they could not find any neutron-diffraction evidence of ordering in a powdered polycrystalline near-stoichiometric Cu2NiZn alloy. There appears to be some essential difference between a near-stoichiometric Cu2NiZn alloy and one somewhat further off stoichiometry as used by the present authors. Thus Sato14 was able to reproduce the low-temperature resistivity anomaly reported by one of the authors13 on the present alloy if he used a similar composition, but found the normal behavior of the residual resistivity in a near-stoichiometric alloy. satol2 found that the resistivity of a cold-drawn slightly off-stoichiometric alloy increased to a maximum on isothermally annealing at 300°C and then decreased ("over-aged"). Since he could not explain this on the basis of ordering phenomenon, he proposed that zinc atoms were segregating to stacking faults (Suzuki effect) and found etching bands on the surface by replication which were attributed to the widening of faults. Sato suggested14 that the hardening effect observed by Phillips and Jones19 is partly due to the Suzuki effect. EXPERIMENTAL The starting material was 1/4-in.-diam hard-drawn rod of a commercial 18 pct "nickel silver" alloy identical with that used in a previous study by Phillips

Jan 1, 1967

By Y. H. Liu, G. W. Powell

Thin foils made from the gold-rich region of- short (0.15 mm)Au-Ag diffusion couples annealed at 880°C for 1 hr were examined in ax electron microscope and the structures were compared with that of pure gold subjected to identical heat treatments. The couples underwent Plastic deformation (bending) during the diffusional anneal. The foils prepared from the diffusion zone have a higher dislocation density and incidence of subboundaries than pure gold. The plastic bending of the couple can be interpreted in terms of the climb of edge dislocations, which are pavallel to the bend axis, along the direction of diffusion. THE interaction of lattice defects during interdiffu-sion between two metals has been considered by several investigators. In particular, da Silva and Mehl,1 Barnes,' and Bardeen and Herring3 have proposed models based on interactions between point and line defects to account for the Kirkendall effect (marker movement). Each of these models is based on dislocation climb, which can either add or remove lattice planes, induced by an under- or supersaturation of vacancies. A theoretical treatment of the nucleation and growth of voids by the condensation of vacancies has been presented by Seitz.4 Stresses can arise in a binary diffusion couple as a result of the vacancy flux and the gradient in the lattice parameter. rinkmman' has investigated the effects of diffusion-induced stresses on void formation; the results of his analysis suggest that voids can form and grow under the influence of these stresses in the absence of an excess vacancy concentration. The relationships between vacancy supersaturation and diffusion-induced stresses and void formation have been elucidated also by Balluffi and seigle6 who concluded that the stress generated by a vacancy supersaturation aids the growth of voids. Experimental evidence which indirectly shows that stresses are produced by chemical diffusion has been obtained by several researchers.2,7-9 This evidence consists in part of the observation by light microscopy of the formation of subgrains, a process characteristic of the high-temperature deformation of some metals during creep.'0 More striking, however, is the plastic bending of short (0.2 mm) Cu-Ni couples observed by Barnes2 and of boron-doped silicon crystals reported by Queisser.9 Diffusion-induced dislocations in iron and silicon have been investigated by Ainslie et a1.11and Schwutte and Queisser,12 respectively, the former using transmission electron microscopy and the latter an X-ray transmission technique. Matthews and Crawford13 observed the formation of boundaries by the climb of interfacial misfit dislocations in thin, vapor-deposited Au-Pd couples diffused in situ in an electron microscope. In order to obtain additional information on the phenomena associated with defect interaction and diffusion-induced stresses in binary couples, an electron transmission study of foils prepared from the diffusion zone of short Au-Ag couples was undertaken. The initial objective was to investigate the processes occurring at various points of the diffusion zone. Subsequent research demonstrated that foils could be prepared only from the gold-rich region of the diffusion zone using the technique described herein. EXPERIMENTAL PROCEDURE Preparation and Annealing of the Diffusion Couples. The couples were made from annealed, high-purity (99.999 pct). polycrvstalline gold and silver sheets (0.075 mm thick). Shall (0.075 by 5 by 17 mm) elec-tropolished coupons of gold and silver were pressure-bonded by heating the two metals in a graphite device to 770°C and holding at this temperature for approximately 30 min. The quality of the bond was ascertained by metallographic examination at 150 times. Each couple subsequently was annealed at 880°C for 1hr; under these conditions, the extreme portions of the

Jan 1, 1968

By A. Hellawell

Specitlrens of the Al-Ge eutectic alloy have been frozen unidivectionally at rates between 2.5 x 10-6 and 2.5 x 10-4 cm per sec and the structure examined by optical and X-ray methods. There is no epitaxial relationship between phases, the aluminum having random orientation and the germanium a preferred (011) fiber textuve. Lamellar colonies which are BINARY eutectic alloys occur between either silicon or germanium with the metals aluminum or silver. common in this alloy are constructed from axial and nonaxial (111) plates of germanium which are related by a variety of twin configurations. Irregular or globular regions of the microstructure are composed of continuous single crystals of each phase, the germanium being heavily twinned. There is limited solid solubility in these systems, and the eutectic phases all involve diamond cubic with fcc crystal structures. In the microstructures of these eutectic mixtures the silicon and germanium crystals exhibit an almost infinite variety of shapes which are notably sensitive to

Jan 1, 1968

By B. C. Allen

The solubility of chromium in liquid silver and that of molybdenum and tungsten in liquid tin have been determined by equilibrating Ike Liquid in a crucible of the solule metal. Generally the weight of solute in solulion was delermined both chemically and from crucible weight losses. The resulting weight percent solubilily of chromium in silver as a function of absolule temperature T is given by log w = -6660/T + 4.02 in the range 960° to 1445°C, and that of molybdenlttrl in tin by log w = —5050/T + 1. 79 in the range 1200° to 2200°C. The values appear unaffected by minor changes in solute composition. Calculations aye made of the parlial molar heal and excess entropy of mixing. The estimated solubility of tungsten in tin is 0.001 pct at 2000°C. Evidence is presented that molybdenwm dissolves in tin without compound for mation and that tungsten and tin form W10Sn. RECENT developments in coatings, heat transfer, and brazing require a knowledge of equilibrium solubilities in a variety of systems at elevated temperatures. Of particular interest are solid-liquid interactions in metal systems involving dilute solutions. This investigation was undertaken since little is known about the phase relations or solubility of chromium in liquid silver or of molybdenum and tungsten in liquid tin.1,2 EXPERIMENTAL WORK As indicated in Table I, high-purity metals or those of known impurity levels were used. Crucibles were machined from chromium, molybdenum, and tungsten bar stock 1.3 cm diam and 2.2 cm long. Chromium rod was prepared by arc melting and extruding iodide process crystals.3 The five chromium impurity alloys were in the form of 0.6-cm-diam swaged rod. A Cr-0.06N* alloy was prepared by exposure to NH3 at 1150°C in a closed quartz capsule for 24 hr. Because significant nitrogen was lost during annealing in argon at 1600°C,4 the estimated level was 0.01 pct N. Chromium and Mo,W crucibles were outgassed at 1200" and 1600°C, respectively, at 3 X 10-5 mm. The solvent was placed In crucibles of the solute metal- 6 g Ag in chromium, 0.4 g Ag in the five chromium impurity alloys, and 4 g Sn in Mo,W crucibles. The silver and tin series were outgassed at 900" and 110O°C, respectively, and held at the desired solution temperature in a tantalum resistance furnace under 1.05 atm 99.995 pct Ar. An equilibration time of 0.5 to 1 hr was chosen since 0.3-, I-, and 4-hr anneals at 1235°C for Cr-Ag yielded similar results. Temperatures were measured optically to +10°C under essentially black body conditions which were checked against the melting point of silver. The Cr-Ag and Mo-Sn,W-Sn series were respectively equilibrated at 990° to 1400°C and 1200" to 2000°C. Vaporization losses were generally held to <1 pct by the argon. In the 1800" and 2000°C anneals for 0.5 hr, the crucibles were placed in tightly sealed tantalum cans which kept tin losses to <5 pct. After the anneals, the specimens were furnace-cooled. One anneal was made on small Mo-0.02 C, Mo-0.5Ti-0.lZr, and tungsten crucibles containing tin at 2200°C. The metals were sealed in an electron-beam-welded tantalum can of minimum volume. After the anneal, tin was still present in each crucible, none of which was severely attacked. After equilibration, the saturated solvent metal was selectively removed from the crucible by acid leaching. Weight losses sustained by the crucibles were determined from the initial weight minus the final blank-corrected weight after acid leaching. Chemical analyses were performed on some of the samples. Hot 1:l HNO3-H2O removed silver from chromium with the blank running <0.1 mg or <0.002 pct on measured solubility. Tin was removed from molybdenum and tungsten by hot concentrated HC1 with the respective blanks amounting to -0.004 and -0.0004 pct in the presence of tin. The insoluble residues were weighed and checked for composition. The leaching solutions contained traces of the solute metals which were analyzed by colorimetric methods, Diphenyl Carbazide for chromium, Thiocyanate for molybdenum, and Dithiol for tungsten. The total of the two percentages found from the residue and leaching solution minus the blank gave the desired solubility values. On the basis of annealing empty molybdenum and tungsten crucibles, weight losses due to MoO3 or WO3 volatilization were found to be generally 10.4 mg and affect measured solubilities by <0.01pct. RESULTS AND DISCUSSION Chromium-Silver . Since no intermediate compounds are reported to form in the Cr-An system,&apos; crucible weight losses and chemical analysis of the entire melt should provide reliable measures of the chromium in solution. Values obtained by the two methods are in agreement as shown by the results for unalloyed chromium in Table II and plotted in Fig. 1. Furthermore, the results are consistent with those previously determined by melting equilibrated silver out of the crucible and analyzing calorimetrically for chromium.&apos; On the basis of limited thermal analysis data, the solubility of chromium in silver has been quoted as 8 pct at the monotectic temperature of -1445°C.1 This investigation indicates an extrapolated solubility of 1.38 pct which is believed to be more reliable. At the eu-

Jan 1, 1968

Jan 1, 1967

By C. N. J. Wagner, E. N. Aqua

The bee alloys of the terminal solid solution of rhenium in niobium were investigated by X-ray diffraclion methods. The analysis of the broadening of the powder pattern peaks from the niobium-rich alloys, cold-worked by filing, showed evidence for faulting on (211) planes. The alloys with larger rhenium concentrations were brittle, and fractured when filed. The analysis of the shapes of the diffraction profiles from powders produced by hammering with steel plates) of these brittle alloys indicated that the broadening was due predominantly to platelets bounded by clibe planes. This result was consistent with the Laue patterns from single-cleazlage facets which showed evidence for clearage fracture on {100} planes. The influence of faulting on the mechanical properties of face-centered cubic (fcc) metals and alloys, i.e., how faulting affects the various dislocation configurations in fcc metals, is well-known.&apos; The important question is whether or not faulting occurs in body-centered cubic (bcc) metals and alloys, and, furthermore, if faulting does occur, to what extent it affects the mechanical properties. Theoretical calculations indicate that the stacking-fault energy is rather high in most bcc metals.2 The results of sev-eral studies using transmission electron microscopy have indicated that faults are present in well-annealed and lightly deformed bcc metals and alloys, such as tungsten,3 vanadium,4 and Mo-Re alloys.5,6 These faults, as have been observed, may be stabilized by the presence of interstitial (C,N,O) atom segregation to the extended dislocations. In addition, there is considerable X-ray diffraction evidence for faulting in bee metals,7-8 using the same techniques that were successful for the study of faulting in fee metals and alloys.7 This X-ray diffraction method is currently the only technique applicable for the investigation of faulting in metals with high stacking fault energies, i.e., when severe amounts of deformation are required to produce sufficient amounts of faulting to be detectable by X-rays. The thinned films of heavily deformed metals will become opaque in the electron microscope due to the high dislocation densities present. In a previous investigation of faulting8 in bee metals of group Vb and VIb, the authors observed that niobium was ductile when filed at room temperature, and showed the highest density of faults on the (112) family of planes. A niobium-base alloy system was therefore chosen to study the effect of alloying on the occurrence of faults in a bcc alloy. There is a large range of terminal solid solubility of rhenium in the alloys of the bee refractory metals. All of the Group VIb-rhenium alloys, i.e., Cr-Re, Mo-Re, and W-Re, exhibit solid solution hardening without loss of ductility.9 In fact, the ductility reaches a maximum for alloys with compositions near to the limits of solubility. This enhanced ductility has been attributed to the lowering of the stacking-fault energy in the alloy; i.e., the increased amounts of twinning provide an additional mode of deformation, resulting in the observed high ductility.&apos; Because of this demonstrated effect of rhenium in bee alloys, it was decided to study a series of alloys of Nb-Re. Using the same X-ray diffraction methods as described in the previous investigation,&apos; one is able to identify the possible causes of broadening of the powder pattern peaks, e.q., particle size, microstrains, stacking faults, and/or twin faults. The separation of these various contributions to the measured peak shape is accomplished by the Warren-Averbach analysis.7 I) EXPERIMENTAL PROCEDURE A series of seven bee solid solution alloys containing from 2.5 to 21.5 at. pct Re (remainder niobium) were prepared at the General Electric Research Laboratory. Buttons, weighing 25 g, were alloyed from electron-beam-melted niobium chips and random rhenium sheet by arc melting in a water-cooled copper crucible, under an argon atmosphere. The buttons were inverted and completely remelted to promote homogenization. The nominal alloy compositions are listed in Table I. Samples of the cold-worked alloys were obtained by filing to produce a powder for the X-ray study. Alloys too brittle to be filed were hammered with steel plates. The resultant filings or brittle impactings were screened through 150-mesh classifiers and compacted to the required shape for the diffractometer holder. The X-ray diffraction peaks were automatically recorded by fixed time counting at uniform 28 intervals, or by continuous registration with a ratemeter. In all cases, the (110)-(220) and (200)-(400) pairs of peaks and the (211), (310), (222), and (321) reflections were measured on a GE-XRD5 diffractometer using CuKa radiation with nickel filter or MoKct radiation and a LiF monochromator in the diffracted beam. The first part of the data reduction, completed with the aid of a series of programmed computations,10 was the analytical resolution of the Kol component of the diffraction profile. Subsequent computations were then made with reference only to the resolved Kol peak shape. These included the measurement of the

Jan 1, 1967

By R. A. Meussner, C. T. Fujii

Chromium solution in wustite depresses the oxygen activity in a nonideal manner and expands the lattice slightly. Gravimetric measurements of the equilibrium compositions of wustite containing 0.00 to 1.38 wt pct Cr define the oxygen potential (CO2-CO atm) and the limits of the phase field at 1000°C. These data extrapolate to a maximum solubility of 2 wt pct Cr. The lattice parameter data, room-temperature measurements of quenched samples, differ significantly from those in the literature. Both pure and chromium wus-tites contract at uniform and equal rates as the oxygen content (metal deficit) increases. The a. US metal deficit relationships are straight lines showing none of the curvature previously reported. At constant metal deficit, the a. expands by 0.002? on alloying with 0.4 to 0.5 wt pct Cr but is insensitive to further chromium additions: a small expansion rather than a marked contraction. These results require a modification of the accepted alloying mechanism. IN the high-temperature oxidation of Fe-Cr alloys in Ha-H,and CO2-CO atmospheres the vapor transfer of oxygen from the continuous wustite outer scale to the porous inner scale/alloy interface sustains the high oxidation rates.1"3 The driving force for this transport is the difference in the oxygen activity of the outer wustite and that at the inner scale/alloy interface. In pure CO2, as well as in CO2-CO atmospheres, carburization of the alloy accompanies this oxidation. Current efforts to evaluate the parameters controlling this carburization have shown that the process is not simple; i.e., the carbon concentration in the alloy initially increases rapidly, reaches a maximum, and then decreases slowly as the oxidation time is extended. This is the same pattern reported by McCoy for the more complex oxidation-carburization of stainless steels and an Fe-Cr alloy in CO2 at lower temperatures.4 These changes in the carburization process occur while the overall oxidation rate and the lattice parameters of the scale layers remain constant. If this invariance of the lattice parameter is assumed to indicate a constant scale composition and thus a constant oxygen potential, the carburization results are not easily explained. Electron microprobe traces across the thickness of these outer scales, however, have revealed distinct chromium gradients penetrating 10 to 50 µ from the inner surface where the chromium concentrations were estimated at a few tenths percent. The variation of the chromium cmcentration on the inner surface of the scale, and the resulting change of the oxygen activity, during the oxidation process is considered to be important in defining the carburization process. Thus, to gain an understanding of the complex oxidation-carburization proc- ess, it was necessary to measure the properties of wustite containing known amounts of chromium (chromium wustite). Although the general features of the Fe-Cr-0 equilibrium diagram between 900° and 1300°C have been fairly well established by Richards and white: Wood-house and White,6 Seybolt,7 and Katsura and Muan,8 there have been no detailed studies of the limits of the chromium wustite phase field or the properties of these alloyed wustites. The recent results of a limited study of chromium wustite by Levin and wagner9 indicate that more than 0.67 wt pct Cr is soluble in wustite above 850°C and that this alloying is accompanied by a substantial lattice contraction. This change in the lattice parameter was not evident in the X-ray diffraction patterns of wustite layers from the oxidation experiments;1,3 the lines were sharp even though a chromium gradient existed in the scale. The present paper describes gravimetric equilibrium experiments which delineate the boundaries of the chromium wustite single-phase field at 1000°C and define the changes in the oxygen activity and the lattice parameter of wustite as functions of chromium and oxygen contents. The lattice parameter data of chromium wustite obtained from these equilibrium and special quenching experiments differ considerably from those reported.9 Those for pure wustite show significant differences from the widely accepted data of Jette and Foote.10 Since the causes of these differences are not easily assignable, and since the literature contains many sets of data on wustite which if not in conflict are at best not in harmony, the experimental procedures are discussed in the present paper. EXPERIMENTAL Oxide Preparation. The specimens used in these studies were porous pellets compacted from high-purity (Fe,Cr)2O3 or Fe2O3 powders. These powders were prepared from electrolytic chromium (99.8 pct purity) and electrolytic iron purified by consumable-electrode, vacuum arc-melting processing (299.9 pct purity).11 The oxides were produced by standard analytical procedures: solution of the metals in acids (HC1, then HNO3 added), coprecipitation of the hydroxides (NHaOH), and filtering and washing these precipitates. Initial dehydration of the coprecipitated hydroxides was done in a porcelain evaporating dish heated by a Meker-type burner, final dehydration by firing in a recrystallized alumina crucible at 1000" to 1050°C for 20 hr in an electrically heated furnace. Spectrographic analysis detected the following impurities: silicon, 0.01 pct or less; aluminum, 0.001 pct to trace; manganese and copper, 0.0001 pct to none. Each of these levels is at least one order of magnitude lower than in commercially available CP grade ferric and chromic oxides. Fluorescence analy-

Jan 1, 1969

By W. T. Roberts, N. G. Turner

A study of the fatigue properties of several grades of commercially pure titanium has established that the strain-aging process is of minor importance in the development of a fatigue limit and a relatively high fatigue strength ratio. Metallographic observations and damping measurements at room temperature indicate that striations are able to spread from grain to grain only at stress levels above the fatigue limit. This suggests that the fatigue limit represents the stress above which large-scale dislocation unlocking takes place. Fatigue tests on annealed material at - 60" and - 196" c showed that under conditions when a thermally activated diffusion process would be suppressed the fatigue limit is not eliminated. Prestraining at room temperature did not have a detrimental effect on fatigue strength at room temperature but a decrease was recorded at — 60°C. This is further evidence that initial dislocation locking is a important strengthening mechanism. TITANIUM and titanium alloys have S-N curves with a definite fatigue limit, and a high ratio of fatigue limit to UTS can be attained. Other materials which show similar fatigue characteristics are mild steel and some Al-Mg alloys. The fatigue limit of these materials has been associated with their strain-aging capacity. It is well-known that commercial-purity titanium contains interstitial impurities which can give rise to a sharp yield point, and a small strain-aging effect following static strain has been demonstrated.7 This type of aging reaction is differentiated from the dynamic aging process when aging occurs during plastic deformation, and which is generally observed at elevated temperatures. In a titanium at room temperature, dislocation locking is associated with the interaction of interstitial oxygen, nitrogen, and carbon atoms with dislocations. Ehr-lich has shown that the distortion produced by introduction of these atoms into the hcp lattice has no shear stress component and hence there is no interaction between the stress field and the screw component of a dislocation. Thus the dislocations as a whole are only weakly locked. It is clear that strain-aging effects in hcp a titanium will be much less pronounced than those observed in bcc iron and steel. In recent years, the attribution of the fatigue limit solely to strain aging has been questioned. It has been pointed out that a definite fatigue limit is observed at temperatures as low as -196°C in some titanium alloys,&apos; and strain aging is not expected to be effective at this temperature. The role of initial locking of dislocations in determining fatigue behavior has been examined in low-carbon steel by Oates and Wilson. They showed that under conditions in which the aging potential is low the factors which control the buildup of local stresses and hence affect dislocation unlocking, e.g., grain size, are important. There are indications that other metals can have a definite fatigue limit with no established strain-aging capacity, an example being magnesium12 which has the same crystal structure as a titanium. The spread of plasticity from grain to grain in hexagonal metals may be more difficult than in cubic metals because of the limited number of slip systems in the former, and this may account in part for their fatigue behavior. The present work was undertaken to elucidate the relative importance of crystal structure, strain aging, and initial dislocation locking in determining the properties of commercially pure titanium when subjected to cyclic stressing. 1) EXPERIMENTAL METHODS Three grades of commercial-purity titanium were used and a material of lower interstitial content was prepared by melting high-purity Japanese sponge titanium (referred to as H.P. Ti). The compositions and typical mechanical properties of the materials are shown in Table I. Fatigue tests were made in push-pull (zero mean stress) using an Amsler Vibraphore machine at a frequency of about 160 cps. Two types of fatigue specimen were used—one with a waisted gage length for determination of S-N curves and the other with a parallel gage length for metallographic studies and damping measurements. After careful machining and mechanical polishing, all specimens were electropolished prior to fatigue testing. The electrolyte consisted of 10 parts methyl alcohol, 6 parts 2-butoxyethanol, and 1 part perchloric acid (SG 1.54) and it was maintained at a temperature of -10" to -20°C during polishing. Tests at room temperature were normally carried out with the specimen immersed in a silicone oil bath which could be heated for elevated-temperature tests.

Jan 1, 1969

By C. J. Rosa, W. C. Hagel

An attempt is made to determine the diffusion coefficients of oxygen ions in hypostoichiometric zirconium oxide. A phenomenological theory is developed for three-phase, unidirectional volume diffusion of a gaseous species from a planar source. Knowledge about oxygen diffusion in a and ß zirconium and experimentally measured rates of movements of interfaces permit the evaluation of oxygen ion diffusivi-ties in ZrO2-x. The results conform to the relationship: sq cm per sec, for the temperature range of 875" to 1050° C. DIFFUSION coefficients of oxygen ions in stoichio-metric oxides have been studied by many investigators. The obtained results not only supplement the knowledge about the lattice-defect structures of oxides and conduction mechanisms but also provide information of technological importance. Rate processes such as oxide sintering, high-temperature creep deformation, and oxidation of metals and their alloys are directly dependent on diffusion phenomena. Unfortunately, diffusion coefficients obtained from studies on stoichio-metric oxides cannot be treated without restraints when applied to oxidation kinetics, if precise evaluations of oxidation rates are desired. Oxides formed on metals are usually nonstoichiometric and exhibit nonuniform distribution of either cation or anion vacancies across their thicknesses. Debuigne and Lehr1 extended Danckwerts&apos;2 mathematical analyses and furnished a semitheoretical treatment for evaluating oxygen diffusion coefficients in zirconium oxide in terms of weight gain measurements during oxidation of zirconium in the temperature range 400° to 850°C. Their calculations are based on theoretical partitioning3 of the total amount of oxygen between a zirconium and its oxide phase. An inherent discrepancy appears to continue throughout their calculations. The amount of oxygen confined to the oxide phase should be corrected by multiplying the calculated oxide thickness by the inverse of Pilling-Bedworth ratio, if expansion of zirconium dioxide is taken into account. The purpose of the present investigation is to provide a new semitheoretical treatment for evaluating diffusion coefficients of moving species in hypostoichiometric oxide. The analyses are relevant to unidirectional volume diffusion. Although the presented method is quite general, its applicability will be discussed in terms of kinetic measurements from oxidation of zirconium at temperatures above the a/ß transition, for reasons stated in the later part of this paper. EXPERIMENTAL Pure, 99.93 wt pct, zirconium samples of approximately 2 by 1 by 0.35 cm were exposed to oxygen for various times at four temperature levels: 875°, 950°, 1000°, and 1050°C. High-purity, better than 99.9 vol pct oxygen was passed through a cold trap and columns containing anhydrous CaSO4 to remove residual water vapor. Before exposing to oxygen at a pressure of 500 Torr, specimens were subjected to wet abrasion on 200- through 600-grit Sic papers and polished with 1—p diamond dust. Prior to oxidizing, all zirconium samples were vacuum-annealed at 10-6 mm Hg for about 15 min at the test temperature. The temperature variation across the uniform heat zone was ±2°C from the preset value. Final polishing, for phase thicknesses measurements, was performed by using 8- and 1-p diamond dust and followed by vibrator polishing with 0.05-µ ? Al2O3 solution. Measurements of phase thicknesses were made by projection on a metallographic viewing screen. Conventional powder X-ray analyses for the oxide were employed. RESULTS Fig. 1 is an example of the cross section of oxidized zirconium. Designations of phases given below this figure are the same as those used in the three-phase diffusion system represented by Fig. 5 in the following section. Zirconium oxidized for longer exposure times showed two types of oxides: white oxide at the surface and an underlaying layer of gray oxide. X-ray powder patterns of these oxides at room tern-

Jan 1, 1969

By H. I. Aaronson, C. Laird

The kinetics of thickening and of lengthening of ?&apos; plates in an Al-3.93 pct Cu alloy in the temperature range 203" to 300" C were determined by means of transmission electron microscopy. The rate of thickening was found to be less than that allowed by volume diffusion control at all temperatures, by amounts which increased with decreasing temperature, in agreement with the predictions of a general theory of precipitate morphology.1 Thickening was treated on the basis of the ledge mechanism. Ledges were deduced to spread across the broad faces of ?&apos; plates at volume dzjrfusion-controlled rates, as anticipated from the disordered structure of their edges. Lengthening of 8&apos; plates, on the other hand, took Place more rapidly than allowed by volume dzjrfusion. This occurred despite clear morPhological evidence of a bmrier to growth at the edges of these plates. It was concluded that the misfit dislocation structure comprising the barrier requires that lengthening take place by a jog mechanism. The tnisfit dislocations, however, also serve as diffusion short circuits, and allow high overall lengthening rates to be achieved. In Part I&apos; it was shown that, within the range of aging temperatures and times studied, the broad faces of 8&apos; plates formed in Al-4 pct Cu are fully coherent with the a, matrix. Virtually .all of the dislocations present in these faces were found to have developed as a result of plastic deformation in the a phase. Such dislocations are thus "intruders", rather than the more usual misfit-compensating variety. The edges of 8&apos; plates were confirmed, by extension of the earlier studies of Mat-suura and Koda,3 to be made up of edge-type misfit dislocations, in sessile orientation with respect to lengthening of the plates. These interfacial structures should cause 8&apos; plates to thicken and to lengthen at rates less than those allowed under the condition of volume diffusion control, such as would be expected if the interphase boundaries had disordered structures.&apos; The narrow width of 8&apos; plates, the reproducible crystallography of their broad faces, and the appearance of these plates in cross section as octagons rather than as circular discs2 provide qualitative support for these deductions. The present study of the rate of thickening and the rate of lengthening of 8&apos; plates was undertaken in order to examine them on a quantitative basis. I) THICKENING KINETICS OF THE BROAD FACES OF?&apos; PLATES A) Literature Review. The measurements now available on the thickening kinetics of single-phase precipitate plates consist of one plot of the thickening of a proeutectoid ferrite plate in an Fe-C alloy,&apos; showing (as predicted) thickening rates less than those allowed by volume diffusion control. B) Experimental Procedure. Details of the preparation of the 4-3.93 pct Cu alloy used in this study have been previously reported.4 As in Part 1,&apos; transmission electron microscopy was the observational tool employed. A general description of the apparatus and procedures of the electron microscopy studies is given in Section I of Part I. In thin foils, 0&apos; plates tend to form at and parallel to the foil surface.&apos; A direct investigation of the thickening process by means of hot-stage transmission electron microscopy was therefore not feasible. It was thus necessary to use the conventional method of aging individual bulk specimens for a wide range of different times at the various temperatures studied. In each specimen, the thicknesses of a number of plates were measured. Since thin foils prepared from "bulk-aged" material contain a large proportion of grains with orientations near (001) , it was relatively easy to find, near the edges of the foils, the characteristic multifold patterns of intersecting extinction contours which indicate regions where the foil is exactly at an (001) orientation. The thicknesses of large numbers of plates were measured along the (200) branches of the "stars" so that the 8&apos; plates were precisely parallel to the optical axis of the microscope. Wherever possible, intersecting extinction contours were adjusted with the parameter s > 0 to improve the visibility of the plates in bright-field illumination. These precautions, in combination with taking the measurements at the thinnest parts of the foils, minimized the errors in the measurement of the thickness of the plates resulting from inexact parallelism to the electron beam. Since the plates were very thin, it was not easy to measure their thickness on the photographs. The techniques of enlargement and of microdensitometry were employed to minimize errors from this part of the measurement. A further source of possible error, that the plates can appear thicker because of contrast associated with mismatch normal to the plane of the plate, was also considered. The images of the plates were usually thinner than those of dislocations, however, and no anomalous changes in apparent plate thickness were observed when regions of foil containing plates were tilted through various diffracting conditions. Any error from this cause must therefore be small. Other sources contributing errors were: a) the microdensitometer traces per se and the subjective estimates of their peak limits, and b) slight fluctuations in magnification associated with small changes in the current of the objective lens of the electron microscope. The overall error probably amounted to no more than 5 to 10 pct. In order to obtain readily interpretable data on thickening kinetics, it is essential that the diffusion fields of adjacent ?&apos; plates not be allowed to overlap. Calculations&apos;-&apos; showed that this condition is definitely not ful-

Jan 1, 1969

By A. K. Mukherjee, J. E. Dorn

A modified Peierls model is Presented for the rationalization of the asymmetric plastic behavior of single crystals of bcc metals. The model assumes that the asymmetry of slip arises from a tendency toward asymnetric splitting of the a/2[111] screw dislocation. The approach differs from former theories however insofar as it assumes that the splitting is so minor ttut only the core energy is modified and that no real partial dislocations exist. As a consequence, the concepts of a line energy of a partial dislocation, interaction between partial dislocations, constriction energies, and stacking fault energies are not invoked. Instead the present analysis is based on a specialization of the Peierls mechanism which assumes an asymmetric dislocation core which is modified by the effective stress and permits cross slip. The theoretical predictions on the stress-temperature -strain rate and orientation relationship agree qualitatively with the limited experimental data that are currently available. Additional experimental work over wider ranges of conditions is suggested to provide more complete evaluation of the possible validity of this theory. RECENT experimental investigations on the low-temperature thermally activated deformation of bcc metals have confirmed the existence of several unique orientation effects. These will be described with the aid of the standard stereographic projection shown in Fig. 1. If slip were determined exclusively by crystal symmetry, the deformation characteristics would be symmetrical about X; = 0 and independent of whether the specimen were subjected to a tension or a compression stress, regardless of what combinations of slip planes might be operative. Experiments, however, reveal that neither of these symmetry based predictions are valid. A schematic representation of the commonly observed asymmetry of both the yield stress and the plane of slip is shown in Fig. 2. A reversal of the direction of stressing results in an inversion of the asvmmetric behavior. 1) Asymmetry bf Yielding. A detailed investigation on the asymmetric yielding in an Fe-2.7 pct Si alloy was repoEted by Tabka, Tikeuchi, and Furubayashi,1 Similar trends have been observed by Keh and Nakada on iron,&apos; Stein on molybdenum,3 Bowen, Christian, and Taylor4 on columbium, Sherwood, Guiu, Kim, and pratt5 on Ta, Cb, and Mo. The degree of asymmetry not only depends on the atomic number and alloying but, in all cases that have been examined, it also increases with a decrease in the test temperature. 2) Asymmetry of the Slip Plane. Asymmetric $I-~: curves of the type shown in Fig. 2 have been found for several Fe-Si alloys6-8,1 and columbium.4 There is general agre_ement that near X: = 30 deg slip occurs by the [111](211) mode so that ?1 = 30 deg. As X; decreases it appears that [111](211) to [111](101) cross slip takes place leading to slip band traces on intermediate planes. And as xi approaches 0 deg, sharp

Jan 1, 1970

By J. B. Wagner, p. Hembree

The iron tracer diffusion coefficient of umstite has been measured at 110(fC across the phase field and at a single composition at 800°C. Assuming a simple cation vacancy model the tracer diffusion coefficient was found to be a linear function of the cation vacancy concentration at 1100°C. The equation is D = 3 x 20 29 where denotes the concentration of vacancies in numbers per cc. The tracer work at 800°C was carried out to investigate the reported "pinning" of tracer to the wustite surface at low temperatures. No evidence for the "pinning" of the tracer was found at 800°C in COz-CO gas mixtures. HIMMEL, Mehl, and Birchenall,&apos; Carter and Richardson,2 and Desmarescaux and La combe3 have measured the diffusion of iron tracer in wustite at several temperatures and compositions. The present work was undertaken to extend the measurements over a large composition range at 1100°C and to resolve certain apparent discrepancies in the data, expecially at lower temperatures. EXPERIMENTAL Wustite was prepared by oxidizing rectangular iron plates* in C02-CO mixtures. The samples were •The iron was supplied by the Battelle Memorial Institute courtesy of the American Iron and Steel Institute. The analysis is presented in Table I. quenched. Due to the inward flow of cation vacancies during oxidation, the center of the sample contained a thin void. The edges of the wustite slab were sanded until the sample could be split into two parts. Each part was then sanded on the front and back flat area until a smooth surface was obtained. The specimens were then replaced in the furnace and equilibrated at llOO°C in a predetermined COa-CO mixture by methods described elsewhere.4"6 The specimens were again quenched and the surfaces were lightly sanded to remove any roughness following the first equilibration. The specimens were then reequi lib rated in the same C02-CO mixture for thirty minutes in order to relieve any mechanical damage on the surface due to the polishing. The specimens were then quenched and the tracer was applied by an electroplating technique. The work of Carter and ~ichardson&apos; demonstrated that there was no systematic difference in the iron tracer diffusion coefficient in wustite if the tracer was plated, dried, or evaporated on the specimen. In the present study a piece of filter paper was saturated with an iron chloride solution of pH <* 3 that contained the tracer FeS5. The wustite was placed on the filter paper and made the cathode. A current density of 0.4 to 0.6 ma per sq cm was passed for about five to ten minutes. The thickness of the tracer layer was estimated to be about 7 x lom6 cm. This estimate was made by considering the area plated, the current flow, and time for plating and the activity of the iron in the plating solution. Different areas of the specimen were counted using a collimator to determine the uniformity of the tracer. Any specimen which exhibited a variation from the initial count rate (about 1500 cpm) by more than 15 pct was rejected. An estimate of the time necessary to convert the thin layer of iron tracer to wustite was made using the data of Pettit and wagner." he estimated time was 1 sec at 1100°C assuming linear oxidation kinetics. The shortest diffusion anneals were 1800 sec. The samples were suspended in the hot zone of a furnace by two platinum wires. Two separate specimens were run at the same time. Only the edges of each sample were in contact with the wires. The C02-CO gas of the same composition as that used in the pre-diffusion anneals flowed freely around the samples at a linear velocity of 0.9 cm per sec. To initiate a run, the specimens were lowered from the cold zone of a furnace to the hot zone by a magnetic lowering device." bout 60 sec were required for lowering. To terminate a run, the sample was withdrawn from the hot zone to the cold zone. Time zero for the beginning of the experiment was taken when the sample blended into the red glow of the furnace and conversely for the end of the experiment. The surface decrease method of measuring the tracer diffusion coefficient was used to collect the data. This method requires that counting geometry be reproducible because the specimen is counted before the diffusion anneal and after the anneal. A special jig was constructed for each specimen so the specimen could be removed from the jig and returned to the jig such that the well geometry was reproducible.

Jan 1, 1970

By H. L. Marcus, P. W. Palmberg

As can be seen from the phase diagram A1-W1 the equilibrium solubility of tungsten in aluminum is practically nil at room temperature. By quenching from the liquid state (50,000°C per sec), Varic, Burov, and Kolesnicenko2 obtained A1-W solid solutions up to 0.15 at. pct W. The quenched alloys were in the form of foils, 0.2 to 0.3 mm thick. Considering the results of Duwez and Willens,3 it is obvious that this thickness, which makes impossible a sufficiently rapid quenching, was the main reason for the relatively low content of tungsten dissolved in aluminum found by Varic.2 he present note shows that the metastable solubility of tungsten in aluminum can be appreciably extended in aluminum-rich A1-W alloys. The quenching technique and the procedure employed for the preparation of the alloys have been described previously.475 The resulting quenched flakes varied in thickness from 1 to 20 µm from experiment to experiment. However, the measurements of the lattice parameters were carried out only with flakes thinner than 5 µm. The areas of quenched flakes were between 0.1 and 15 mm2. The quenched flakes were placed into a 0.3-mm glass capillary tube which was then mounted in a 114.6-mm-diam Debye-Scherrer camera. Straumanis asymmetric film position and nickel-filtered CuKa radiation were used. The lattice spacings were computed taking X(CuKa1) = 1.54050A for resolved and ?(CuKa) = 1.54178A for unresolved doublets. All specimens were rotated at room temperature, 26" +2°C. The lattice parameters were estimated from extrapolation against the Nelson-Riley function. It was estimated that the error in the lattice parameter of the measurements on a single film lies within +0.0004A for lower and about +0.001A for higher concentrations of tungsten. The lattice parameters of the metastable solid solutions A1-W are plotted vs the concentration of tungsten in Fig. 1 together with the parameters measured by previous investigators.&apos; Each point of the present measurements represents a determination of the lattice spacing on different quenched flakes, for a given concentration of tungsten. With experimental accuracy, the lattice parameters of the metastable solid solutions fall on the straight line passing through the already known data.&apos; As estimated from the uncertainties in the lattice spacings of the solid solutions, the alloys were homogeneous within 0.1 at. pct W. The solubility of tungsten in aluminum-rich A1-W solid solutions obtained by a very rapid quenching technique is increased to about 0.95 at. pct W. This value is 6 times greater than the amount known up to now. -he lattice parameters of the resultant aluminum solid solutions with higher concentrations of tungsten than 0.95 at. pct W did not remain constant AUGER electron spectroscopy has been used to clarify the role of impurities in the embrittlement of AISI 3340 steel. Analysis of fracture surfaces has shown that the embrittled condition is correlated with appreciable antimony segregation at grain boundaries. The low temperature (400" to 600°C) temper embrittlement of low alloy steels containing various combinations of Cr, Ni, Sb, Mn, P, Sn, and As has been examined extensively for many years. General reviews of the area have been made by McMahon1 in 1968, LOW&apos; in 1959, woodfine3 in 1953, and Holloman4 in 1946. Recent work by Low, Stein, Turkalo, and LaForce5 has done much in separating the alloy and

Jan 1, 1970

By A. Tonejc, A. Bonefacic

As can be seen from the phase diagram A1-W1 the equilibrium solubility of tungsten in aluminum is practically nil at room temperature. By quenching from the liquid state (50,000°C per sec), Varic, Burov, and Kolesnicenko2 obtained A1-W solid solutions up to 0.15 at. pct W. The quenched alloys were in the form of foils, 0.2 to 0.3 mm thick. Considering the results of Duwez and Willens,3 it is obvious that this thickness, which makes impossible a sufficiently rapid quenching, was the main reason for the relatively low content of tungsten dissolved in aluminum found by varic.2 he present note shows that the metastable solubility of tungsten in aluminum can be appreciably extended in aluminum-rich A1-W alloys. The quenching technique and the procedure employed for the preparation of the alloys have been described previously.475 The resulting quenched flakes varied in thickness from 1 to 20 µm from experiment to experiment. However, the measurements of the lattice parameters were carried out only with flakes thinner than 5 µm. The areas of quenched flakes were between 0.1 and 15 mm2. The quenched flakes were placed into a 0.3-mm glass capillary tube which was then mounted in a 114.6-mm-diam Debye-Scherrer camera. Straumanis asymmetric film position and nickel-filtered CuKa radiation were used. The lattice spacings were computed taking X(CuKa1) = 1.54050A for resolved and ?(CuKa) = 1.54178A for unresolved doublets. All specimens were rotated at room temperature, 26o +2°C. The lattice parameters were estimated from extrapolation against the Nelson-Riley function. It was estimated that the error in the lattice parameter of the measurements on a single film lies within +0.0004A for lower and about +0.001A for higher concentrations of tungsten. The lattice parameters of the metastable solid solutions A1-W are plotted vs the concentration of tungsten in Fig. 1 together with the parameters measured by previous investigators.&apos; Each point of the present measurements represents a determination of the lattice spacing on different quenched flakes, for a given concentration of tungsten. With experimental accuracy, the lattice parameters of the metastable solid solutions fall on the straight line passing through the already known data.&apos; As estimated from the uncertainties in the lattice spacings of the solid solutions, the alloys were homogeneous within 0.1 at. pct W. The solubility of tungsten in aluminum-rich A1-W solid solutions obtained by a very rapid quenching technique is increased to about 0.95 at. pct W. This value is 6 times greater than the amount known up to now. -he lattice parameters of the resultant aluminum solid solutions with higher concentrations of tungsten than 0.95 at. pct W did not remain constant AUGER electron spectroscopy has been used to clarify the role of impurities in the embrittlement of AISI 3340 steel. Analysis of fracture surfaces has shown that the embrittled condition is correlated with appreciable antimony segregation at grain boundaries. The low temperature (400" to 600°C) temper embrittlement of low alloy steels containing various combinations of Cr , Ni , Sb , Mn , P , Sn , and As has been examined extensively for many years. General reviews of the area have been made by McMahon1 in 1968, LOW&apos; in 1959, woodfine3 in 1953, and Holloman4 in 1946. Recent work by Low, Stein, Turkalo, and LaForce5 has done much in separating the alloy and

Jan 1, 1970

By R. L. Orr, J. D. G. Masse, Ralph Hultgren

The relative partial molar enthalpies of gold and tin in liquid Au-Sn alloys have been measured from Xsn = 0.474 to 0.510 at 696°K, slightly above the melting point of solid AuSn. Within an average precision of 6 cal per g-atom, the data are represented by two smooth curves, which satisfy the Gibbs-Duhem relationship and which do not show any anomalous behavior in the range of composition studied. The results give no support to the hypothesis that atomic associations in the equiatomic liquid alloy resemble those in solid AuSu. LITTLE has been firmly established as to the nature of atomic distribution in liquid metallic phases. A favored hypothesis assumes the existence of atomic groupings in the liquid phase which are similar to those in solid phases occurring at lower temperatures. Beginning with this hypothesis, it is often possible to adjust the values of certain parameters (such as degree of association) so that approximate agreement is achieved with certain features of the X-ray diffraction pattern of the liquid, even though many other possible structures might satisfy the data equally well. Thus, in this manner, the structure of liquid tin has been described as a dispersion of fragments of gray tin in a matrix of metallic tin.1 Four X-ray diffraction studies2"5 have been made of the liquid alloy of composition AuSn at temperatures slightly above the melting point of the solid. Each investigator concluded, on somewhat different grounds, that the liquid consisted to a large extent of arrays of atoms similar to the solid, with admixture of more disordered arrays. Solid AuSn has the nickel arsenide crystal structure: each tin atom has six nearest neighbors, all gold atoms; and each gold atom has six tin and two gold atoms as nearest neighbors. It remains highly ordered to the melting point. The liquid alloy has a large exothermic (?H700° K = -2700 cal per g-atom6) enthalpy of formation, favoring ordering and making the hypothetical molecular association not unreasonable. The possible existence of such solidlike arrays, or of a high degree of order that occurs preferentially at a specific composition in a liquid alloy, might also be revealed by thermodynamic behavior somewhat analogous to that in highly ordered solid alloy phases. The latter often exist over wide composition ranges, within which the highest degree of order occurs at the ideal composition for which the atomic fractions are equal to the fractions of sites which are "right" for each kind of atom. On departing from the ideal composition, the excess atoms occupy "wrong" positions, raising the internal energy and making it progressively easier for additional atoms to occupy "wrong" positions. Thus, on either side of the ideal composition, there should be a pronounced rise in the entropy and enthalpy, which would be shown particularly by the change in the relative partial molar enthalpies, ?Hi, since they depend strongly on d?H/dx. In the one case where accurate measurements have been made, the solid AuCu ordered phase, the structure becomes much less ordered as the composition deviates from the ideal, and relative partial molar enthalpies change sharply as shown by the data6 given in Table I. This suggests the possibility of finding similar pronounced changes in the relative partial molar enthalpies of gold and tin in liquid alloys near the composition AuSn if the postulated solidlike ar-

Jan 1, 1967

By G. Beghi, G. Piatti

THE authors examined the problem of the gradual transformation of Al2O3 from the transition phases normally encountered in SAP (r -x-n)1-3 to the stable a phase. This phenomenon is well-known at temperatures above the melting point of aluminum,3"6 whereas in this paper the transformation was studied at temperatures lower than the melting point of the aluminum matrix.

Jan 1, 1967

By R. W. Bartlett

DISILICIDE coatings, MeSi2, on refractory metals are usually grown by a solid-state diffusion reaction similar to the parabolic oxidation of metals. Two or more silicide compounds occur in each of the binary silicon-refractory metal systems. When an adequate source of silicon is available during the coating process, the lower silicide compounds are usually not formed.1 However, during service application of the coated refractory metal, continued heating causes further diffusion and growth of the lower silicides. A study of the growth kinetics of the lower silicides in the molybdenum and tungsten binary systems with silicon was previously reported.2 The present study is concerned with the growth kinetics of Ta5Si3 and Cb5Si3, formed as conjugate layers between TaSi2/Ta and CbSi2/Cb diffusion couples, respectively. Diffusion couples consisting of disilicide-coated tantalum and columbium sheet coupons were subjected to diffusion heat treatments, cross-sectioned, and scanned by an electron-microprobe analyzer to determine the relative X-ray intensity profiles. These profiles correspond closely to concentration profiles for the constituents, and were used to identify phases and locate phase boundaries. The analysis of a single specimen after a diffusion-anneal provides only one value for the Me5Si3 phase thickness, corresponding to the time and temperature of the diffusion treatment. Consequently, each isothermal curve showing the rate of accumulation or depletion of silicide phases required several samples with identical diffusion temperatures but different diffusion times. The disilicide coatings were prepared by pyrolizing commercially pure silane in a hydrogen carrier gas. The hydrogen was purified by passage through a palladium membrane. Commercially pure tantalum and columbium sheet metal coupons, 0.005 by $ by 2 in., were used. All of the coated specimens for each system were prepared together in a single group in order to minimize coating variations among individual specimens. During pyrolysis, the brightness temperature was maintained at 1200°C. With suitable flow rates at this temperature, only the disilicides of tantalum and columbium were formed in detectable amounts. Coated specimens were subjected to diffusion an-neals in a tube furnace with automatic proportional control within ±10°C. A H2-Ar mixture, deoxidized and dried over anhydrous magnesium perchlorate, was used to prevent oxidation during the diffusion anneal. Diffusion couples were cross-sectioned, polished and examined with an A.R.L. electron-microprobe X-ray analyzer. Both metal constituents in each specimen were simultaneously scanned using a 1-p beam spot size and either 1- or 2-µ steps. Analyses were performed using the Ka radiation of columbium and silicon, and the La, radiation of tantalum. For all specimens, an acceleration voltage of 30 kv was used, and integration was made against the specimen current. LiF and A DP monochrometers were used to isolate characteristic radiations. Three or more traverses were made on each specimen. The intensity scales were adjusted using the constituent metals and standard samples of the silicide compounds which had been verified by X-ray diffraction. The relative intensity profiles were used directly, in conjunction with the standard samples, to identify compounds and phase boundaries. The stoichiometries differ considerably between the silicide compounds in both systems, and the homogeneity range for these silicide compounds is narrow. These characteristics result in marked differences in relative intensities of the fluorescing elements—differences which permit ready identification of phases and phase boundaries. Projections of both electron back-scattered images and characteristic

Jan 1, 1967

By R. D. Pehlke, J. V. Gluck

AS a portion of a general study of liquid-metal thermodynamics, high-temperature galvanic cells were used to study the effect of added dilute solutes on the activity of zinc in dilute solution with molten bismuth in the range 450° to 650°C. 1,2 The cells were of the type The experimental procedures have been described previously.1 In the course of studies conducted in the bismuth-rich corner of the systems Bi-Zn-Au and Bi-Zn-Cu, marked discontinuities were observed in the electromotive force-temperature relations for a number of the experimental compositions. Above the discontinuity temperatures, the relations, which were linear, exhibited slopes similar to the binary alloy of the same mole fraction zinc, as shown in Figs. I and 2. Below the discontinuity temperatures, the slopes were markedly different, but the relations remained linear. In general, as the amount of the third eletnent was increased, the slope of the lower portion of the relations tended to become less positive. The slopes of electromotive force-temperature relations reflect the entropy of mixing of zinc and, therefore, the occurrence of a discontinuity marks the transition between two different equilibrium situations involving the solution of zinc. A number of other investigators3-5 have used such observations to determine liquidus boundaries in binary alloys. Since the upper portions of the ternary electromotive force-temperature relations of this study had the same slopes as the binary alloys, the discontinuities are interpreted as marking the transition between the single-phase liquid region and the underlying two- and three-phase regions. Reference to the Zn-Bi equilibrium diagram6 confirms that the binary alloys were single-phase liquids at the experimental temperatures. Fig. I shows the electromotive force-temperature relations for the alloys containing Bi-Zn-Au and Fig. 2 shows similar relations for the Bi-Zn-Cu alloys. In the lower portion of each figure, the temperature of the discontinuity is plotted vs the mole fraction of the added solute at the various levels of zinc concentra- tion. Cross-plots from these curves at constant temperature permitted the construction of the partial liquidus surface isotherms shown in Figs. 3 and 4.

Jan 1, 1967