Search Documents

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935

By S.S. Clarke

The sheet-ground deposits of the Tri-State district, because they are fairly uniform in thickness (7 to II ft.)—rather flat, with an easy dip to the west—and cover a large acreage, offered a problem of improved transportation. Heading advance in this kind of mine is very rapid and track haulage requires a larger crew of trackmen than do other mines, and a heavy investment in track. The use of some type of rubber-tired truck equipment for underground haulage was under consideration for some time by the Eagle-Picher Mining and Smelting Co. The nature of some ore bodies made them not adaptable to truck haulage and some mines that did offer possibilities were equipped with other types of haulage, and the expected savings by the use of trucks did not offset the loss of investment that would be incurred in discarding other equipment. The decision was made to sink a new shaft, designed for skip hoisting, on the Blue Goose ore body, and then develop truck equipment. Developing Tractors and Trailers A study was made of internal-combustion engines for power units in the tractors, but the extreme difficulty of controlling air circulation, and the heavy cost of drilling large churn drill holes for blower installations, led to the adoption of a tractor with a storage battery. The storage-battery tractor that was on the market for mine haulage was impossible to obtain because all were needed for defense work. Several standard electric-truck chassis were purchased and rebuilt in the Eagle-Picher shops. The steering wheel was shortened and set vertical, permitting the driver's seat to be moved forward, and the frame was shortened enough to take the battery box and the fifth wheel support that carried the gooseneck of the dump trailer. The fifth wheel, or turntable, is of the ball and socket type. Tig. I shows the ball fastened to the gooseneck. The socket is split to permit introduction of the ball and is held by through-bolts, and the socket is welded to a ½-in. plate, which in turn is attached to the tractor frame. Smaller wheels and tires were put on to reduce over-all height. If it had been necessary, the spring: could have been reversed, or taken off entirely, to gain additional clearance. The tractors are equipped with 48-cell, 23-plate, 400-A.H. batteries. With the initial tonnage and mileage, the batteries were about 50 per cent down at the end of a shift. Tractors have truck tires 7.50 by 20, 8-ply, front and rear, the rear being dud. After four months of use, the .tires are beginning to show signs of failure.* In

Jan 1, 1943

By S. S. Clarke

The sheet-ground deposits of the Tri-State district, because they are fairly uniform in thickness (7 to II ft.)—rather flat, with an easy dip to the west—and cover a large acreage, offered a problem of improved transportation. Heading advance in this kind of mine is very rapid and track haulage requires a larger crew of trackmen than do other mines, and a heavy investment in track. The use of some type of rubber-tired truck equipment for underground haulage was under consideration for some time by the Eagle-Picher Mining and Smelting Co. The nature of some ore bodies made them not adaptable to truck haulage and some mines that did offer possibilities were equipped with other types of haulage, and the expected savings by the use of trucks did not offset the loss of investment that would be incurred in discarding other equipment. The decision was made to sink a new shaft, designed for skip hoisting, on the Blue Goose ore body, and then develop truck equipment. Developing Tractors and Trailers A study was made of internal-combustion engines for power units in the tractors, but the extreme difficulty of controlling air circulation, and the heavy cost of drilling large churn drill holes for blower installations, led to the adoption of a tractor with a storage battery. The storage-battery tractor that was on the market for mine haulage was impossible to obtain because all were needed for defense work. Several standard electric-truck chassis were purchased and rebuilt in the Eagle-Picher shops. The steering wheel was shortened and set vertical, permitting the driver's seat to be moved forward, and the frame was shortened enough to take the battery box and the fifth wheel support that carried the gooseneck of the dump trailer. The fifth wheel, or turntable, is of the ball and socket type. Tig. I shows the ball fastened to the gooseneck. The socket is split to permit introduction of the ball and is held by through-bolts, and the socket is welded to a ½-in. plate, which in turn is attached to the tractor frame. Smaller wheels and tires were put on to reduce over-all height. If it had been necessary, the spring: could have been reversed, or taken off entirely, to gain additional clearance. The tractors are equipped with 48-cell, 23-plate, 400-A.H. batteries. With the initial tonnage and mileage, the batteries were about 50 per cent down at the end of a shift. Tractors have truck tires 7.50 by 20, 8-ply, front and rear, the rear being dud. After four months of use, the .tires are beginning to show signs of failure.* In

Jan 1, 1943

By Harry H. Angst

The history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. 'She elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,090 tons of 012 and 18,000 tons Of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4½-cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. Equipment On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-diii~lp trucks rather than smaller trucks, for the following reasons: I. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4½-cu. yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1943

By Harry H. Angst

The history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. 'She elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,090 tons of 012 and 18,000 tons Of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4½-cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. Equipment On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-diii~lp trucks rather than smaller trucks, for the following reasons: I. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4½-cu. yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1943

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Wilson B. Emery

The Hidden Dome gas field, situated in Washakie County, Wyoming, was discovered Sept. 26, 1917. Subsequently five additional gas wells were completed and a large reserve was developed. For a number of years this field completely supplied the domestic market at Basin and Greybull, as well as the refinery at the latter town, and it is still supplying gas in small amounts to this market. Production is obtained from the sands of the Frontier formation at depths ranging from 1000 to 1500 ft. The original rock pressure was 725 Ib. and initial production ranged from 4,000,000 to 28,000,000 cu. ft. per day per well. Porosity of the sand, determined from the size of the productive area and the amount of gas recovered, is over 18 per cent. Area and Management It is estimated that the productive area is about 640 acres. Its outline is indicated on Fig. 5, on which are also shown the locations of holes drilled on the structure and the area of unit operation. The unit area is owned by the Ohio Oil Co. and development and operation have been by this company. No productive well has been completed outside this area. The entire area was Government land filed on under the placer mining law. Results of Unit Operation With six producing wells, or an average of one to each 160 acres, the pool is completely developed. Location of the wells was made with respect to structural conditions plus the requirement that at least one well be drilled on each 160-acre placer claim. Perhaps a somewhat more uniform spacing of the wells might have been accomplished and one well eliminated, but it must be borne in mind that the holes, on account of their shallow depth, were not expensive and that the object was to develop as reliable a reserve as possible. There is no cause to suspect that these holes have not adequately drained the reservoir and there is every reason to think that any additional wells, which might have been drilled under diversified ownership and operation, would have been an economic waste. Unit operation by a competent company has not only resulted in the elimination of loss of gas through careless development and operation

Jan 1, 1930

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth's surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer's airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist's artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth's surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer's airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist's artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941

By A. A. Scheil, S. I. Hoyt

In technological studies on steel considerable emphasis has been placed on the identification of the foreign inclusions, testimony of which is adequately given in the metallographic literature covering methods for their identification. The outstanding accomplishment in this field is the scheme devised by Campbell, Comstock and Wohrman for identifying various oxides, sulfides, silicates and other constituents by systematic etching tests and microscopic examination.' The time involved in carrying out this procedure has led to attempts to secure quicker methods, or at least to shorten the time required to secure essential information. An example of this is the use of dark field illuminatin,2 but when this was tried out by the authors it was found that cavities and pits on the polished surface appeared bright on a dark field and could not be distinguished from small glassy inclusions. Still another means is the Leitz Ultropak, an instrument equipped with optical units for the illumination of the specimen by reflected light to secure an effect similar to dark field illumination. The structures are made visible in exceedingly sharp details by utilizing the inherent properties of the samples, such as refractive index, absorption coefficients and reflection powers. We have had no experience with the Ultropak, but a recent paper by Benedicks and Löfquist3 describes methods for determining the refractive index of (Fe, Mn) O and MnS by the use of this equipment. Presumably this method would be subject to about the same limitations as dark field illumination, though the, feature added by Benedicks and Löfquist appears to offer great promise in inclusion identification.

Jan 1, 1935

By A. A. Scheil, S. I. Hoyt

In technological studies on steel considerable emphasis has been placed on the identification of the foreign inclusions, testimony of which is adequately given in the metallographic literature covering methods for their identification. The outstanding accomplishment in this field is the scheme devised by Campbell, Comstock and Wohrman for identifying various oxides, sulfides, silicates and other constituents by systematic etching tests and microscopic examination.' The time involved in carrying out this procedure has led to attempts to secure quicker methods, or at least to shorten the time required to secure essential information. An example of this is the use of dark field illuminatin,2 but when this was tried out by the authors it was found that cavities and pits on the polished surface appeared bright on a dark field and could not be distinguished from small glassy inclusions. Still another means is the Leitz Ultropak, an instrument equipped with optical units for the illumination of the specimen by reflected light to secure an effect similar to dark field illumination. The structures are made visible in exceedingly sharp details by utilizing the inherent properties of the samples, such as refractive index, absorption coefficients and reflection powers. We have had no experience with the Ultropak, but a recent paper by Benedicks and Löfquist3 describes methods for determining the refractive index of (Fe, Mn) O and MnS by the use of this equipment. Presumably this method would be subject to about the same limitations as dark field illumination, though the, feature added by Benedicks and Löfquist appears to offer great promise in inclusion identification.

Jan 1, 1935

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By H. E. Nold

ThE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained. For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. Periodic Kilns Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks. In order that heat can be distributed uniformly throughout the pile or setting, the units are placed so as to leave open spaces or flues throughout the pile for the passage of the hot gases. Each kiln is provided with a number of fireboxes (usually 10 or 12) spaced equally in the outside wall. The fireboxes may be equipped with flat or inclined grate bars or they may have no grates at all (dead bottom). Down-draft kilns are most used. In these the hot gaseous products of combustion from the fireboxes are deflected upward by bag walls just inside the fire zone. From the top of the kiln the gases are drawn down through the setting, off through holes in the kiln bottom, and conducted to a stack or stacks. In up-draft kilns the fireboxes are usually set somewhat lower. The hot gases are drawn inward and upward through the ware and pass off from the top. Up-draft kilns find their greatest use in the firing of common brick. In either case the problem is to maintain, as nearly as possible,

Jan 1, 1934

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By W. M. Peirce, R. K. Waring

Zinc of high purity offers definite advantages in certain fields. A process by which zinc of 99.99 + per cent purity is produced by pyro-metallurgical methods is described in this paper. The process consists of a fractional distillation following the primary reduction; this fractional distillation employs the principles of rectification for the separation of lead and other high-boiling impurities and cadmium and other low-boiling impurities. Theoretical Considerations Involved in Production of High-purity Zinc by Distillation Fractional distillation, fractional condensation, and rectification are recognized methods of separating mixtures of liquids. In the field of organic liquids these methods are widely used but not commonly to effect as complete a separation of liquids as is done in the problem under consideration. Zinc boils at 905" C., cadmium at 778" C. and lead at about 1620" C. Zinc may contain from several hundredths of one per cent to over one per cent each of cadmium and lead, and the problem is to reduce these impurities to a few thousandths of one per cent. For lead and zinc, the spread in boiling points is substantial, 715° C., while for zinc and cadmium it is only 127" C. The basic limitation of any separation by distillation may be found from the relation between the equilibrium composition of the vapor and the liquid for all mixtures of the two substances involved. If a mixture of constant boiling point is found, or if a stable compound that vaporizes without dissociation occurs, there is a definite theoretical limit to the degree of separation that is possible when operating at atmospheric pressure with respect to that mixture. Otherwise, any degree of separation is theoretically possible. The equilibrium composition of vapor in contact with liquid mixtures of zinc and cadmiurn at the boiling point has been determined experi-

Jan 1, 1937

By R. R. McNaughton

The Consolidated Mining and Smelting Company of Canada, Ltd. at Trail, B. C., inaugurated a comprehensive program of investigation about 15 years ago to develop the most economical process of recovering the metal in the large accumulated stock of by-products of the lead smelter and the zinc plant. Two principal methods of recovery were followed to a successful conclusion—an electrothermic process to treat zinc-plant residues and cold slag and the fuming of hot slag from the lead blast furnaces. The latter was selected because it showed a saving over the former in its ability to handle hot blast-furnace slag, thus obviating the necessity of granulating, handling and eventually remelting the same slag for the electrothermic process. The design of a fuming plant was commenced in 1928, and construction, which was started immediately, was completed in July 1030. Operating intermittently for a general tuning up, the plant was officially blown in for regular operation in August. During this month the vagaries of a slag-fuming plant were studied and an operating crew was trained. A history of slag fuming at Trail and the development of plant design is given in a paper by G. E. Murray in the Transactions of the Canadian Institute of Mining and Metallurgy for 1933. Fuming Plant The fuming plant at Trail (Fig. 1) is a separate unit although of necessity interlocked closely with the lead smelter. The plant consists essentially of a fuming furnace with its accessories, a waste-heat boiler followed by an economizer, and a suction-type baghouse. The plant was built as the first of two 400-ton units with the intention of adding the second unit within a year, so that flues, fans and buildings were built to handle double the original load. Furnace.—The furnace as originally built (Fig. 2) was of water-jacket construction, 10 ft. wide, 20 ft. long and 6 to 10 ft. high. The roof height was made variable to check experimental work, which had indicated that this dimension affected the rate of reduction. Coal and air were supplied

Jan 1, 1937