Search Documents

THE irregularity of the Mount Morgan ore body presents problems other than those for mining only. For irregularity of outline is coupled with irregularity of grade, and the ore varies so rapidly from profitable to non-profitable, and from highly siliceous to highly pyritic, that the task of estimating quantities and values of ore reserves is manifestly rendered a difficult one, while the actual disposal Of the broken ore demands constant supervision.Four classes of ore are handled. The oxidized ore, cheaply mined and cheaply treated, is obtained by quarrying from the top of the mountain. Below the 315-ft. mine level (measured from the original summit) sulphide ore comes in, and this is divided into siliceous sulphide ore (too siliceous for economic smelting), sulphide ore suitable for smelting, and ore too poor either to be smelted or to be treated by wet process with the siliceous ore. It is with these three latter descriptions of ore that this paper principally deals.Although the output from most stopes in the mine may usually be presumed beforehand to be either smelting or wet-treatment ore...

Jan 1, 1910

By Yogesh Narula

Nevis Bluff Landslide - On September 17” 2000, a rockfall measuring lO,OOOm3 at Nevis Bluff, New Zealand, triggered a loday emergency. It ended when a hazardous column of rock that towered over State Highway 6 was finally shattered. The operation called for unusual and unique solutions using aerial bombing and inverted blasting techniques, not known to have been attempted before under these conditions, anywhere in the world.

Jan 1, 2002

By Joy Sandberg

The 1989 mining industry compensation survey done annually by the Denver-based Mountain States Employers Council shows the "average" or "typical" employee in the mining industry is projected to receive an increase of 3.9% to base pay in 1990, compared to a projection of 4.1 % for 1989. According to MSEC, the actual percentage increase to base pay has continued to decline since 1980. A review of pay increases since 1980 shows the highest average increase was 11%, granted in 1981. Since 1981, there has been a steady deceleration through the decade. While 1989 final figures are not available, 1988 numbers might indicate a reversal of this trend. In 1988, the average employee actual increase was 3.8%. That was 0.7% higher than the 3.1% projection. This may be significant as actual increases have been lower than projections since 1982. Chart A shows the pattern of projected vs. actual percent increases in pay since 1980.

Jan 1, 1990

By Syd S. Peng

Mountaintop removal (MTR) mining started in West Virginia nearly 30 years ago. This surface mining method can extract multiple coal seams as thin as a few inches in whole and minimum rock dilution in very steep mountainous terrain. MTR is highly efficient, even if coal seams are in close proximity and small in a real extent. Consequently, MTR has been widely used in the Central Appalachian coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impact on the surrounding area. During the past two years, however, the debate over MTR mining has grown quickly and has become very intense. This article describes chronologically issues raised by various parties, legal actions, impacts on mining permit applications and research projects developed to address the issues.

Jan 1, 2000

Diesel powered machines are doing some specific operations in the cyclic order required by the technical process. The dynamics of this process in certain conditions has an essential influence on environmental health conditions in the working area. The main purpose of this paper is to show, using computer simulation, how the movement (dynamic) of diesel vehicles effects environmental health standards and also how to determine the required air quantity for ventilation.

Jan 6, 1985

By Andrew M. Wala

The determination of air quantity needed to dilute the exhaust gases to a safe level has to be individually evaluated for particular cases. The diesel powered machines are doing some specific operations in the cyclic order required by the technical process. The dynamics of this process in certain conditions has an essential influence on environmental health conditions in the working area. The main purpose of this paper is to show, using computer simulation, how the movement (dynamic) of diesel vehicles effects environmental health standards and also how to determine the required air quantity for certain conditions

Jan 1, 1983

By K. E. Wood, K. J. DiRocco, L. A. Becker

The Russia Wharf segment of the Silver Line Phase II Project for the MBTA incorporated ground freezing and underpinning during New Austrian Tunneling Method(NATM) tunneling through timber pile foundations, urban fill, and abandoned wharf structures beneath two historic 7-story buildings with steel frames and masonry facades. During construction, the project team implemented an extensive program to monitor, evaluate, and mitigate the ground and building movements caused by the various construction activities. Mitigation included freeze cycling and building raising/lowering to compensate for ground movements and safely maintain the serviceability and occupancy of the buildings. In this paper, we present the history of the freeze, tunnel construction, and thaw-related movements that occurred and the building response that we observed.

Jan 1, 2005

By Keith Henderson

An open pit quarry operation in West Central Illinois provided a challenging proposition regarding the removal of a rock wall that once separated two pits, but was now in the middle of the north wall of the combined pit. Their mining plan included the development of a new ramp into the quarry pit in order to lessen the slope and to shorten haul truck cycle time. The task would be to remove a section of rock left behind from mining operations more than 20 years ago that was at or near the bottom of the designed ramp.

Jan 1, 2012

By S Worden, P A. Kirsch, A Kirsch

Despite the current downturn, coal remains an important commodity in the Australian economy. Increasing coal resource development has resulted in increasing competition for land use in coal mining regions across the country with communities and other stakeholders becoming more adept at articulating their concerns regarding this competition in a range of traditional and social forms of media. In this environment, obtaining and maintaining a social licence to operate (SLO) is problematic and has been identified as the fourth greatest risk facing the international mining industry.This research presents the findings from a longitudinal study on how Australian newspapers frame the views of coal mining stakeholders across each stage of the coal mining life cycle. News stories from national, state and regional newspapers in 2000, 2006 and 2013 were analysed.Over the study period, there have been significant changes in the coal mining themes being covered by Australian newspapers, the number of stories being published, the number of newspapers covering coal mining stories, and the diversity of stakeholders being quoted. How do the dominant themes in media communication change over time? How do these changes impact mining across the life-of-mine?The research confirmed that Australian journalists use framing, priming, labels and bias to conceptualise and understand the events that they report, and that this behaviour has a profound effect on public opinion.CITATION:Worden, S, Kirsch, A and Kirsch, P A, ?2014. Moving beyond economic framing of the Australian coal industry, in Proceedings Life-of-Mine 2014 , pp 365–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By David Caiden, Geoffrey Fosbrook, Jaidev Sankar, Donald Phillips, Jon Hurt, Anil Parikh

This paper will cover the progress being made on Phase 1 of New York’s Second Avenue Subway line. It will include a description of construction progress on the first contract to be let, which consists of a 248 m (815 ft) long launch box, 3.9 km(2.4 miles) of TBM tunnels and a tunnel sump; the packaging strategy for the remaining work; and the progress through Final Design of the remaining packages, including the two large span rock cavern stations.

Jan 1, 2007

By Robert J. Mac Kinnon

A moving grid finite element model for the analysis of transients in a rock mass surrounding an underground coal conversion cavity is presented. Major model components are outlined, including a special element formulated to account for internal discontinuities. A numerical example is described.

Jan 1, 1986

By S. Ianos, C. Vibert

Type and shape of large dams founded on rock depend upon the expected deformation of their foundation. Their design consequently requires the assessment of the deformability of the rock mass at large scale. Seismic refraction, laboratory tests on rock samples and empirical formulas can provide an order of magnitude of the deformation modulus, with a limited degree of reliability. Direct in-situ measurement of the deformability of a volume of rock is therefore preferred, which integrate the effect of discontinuities, such as plate loading tests, dilatometric tests, etc. The authors have been compiling results obtained by in-situ deformability tests on a number of dam sites, including the Scarabée (“Petite Sismique”) method. This last method consists in thoroughly analysing the shape of seismic wave forms transmitted through the rock mass. It has been used since now more than 40 years over a large number of dam foundations, and has proved to provide a satisfactory assessment of the static deformation modulus. After comparing the results obtained from different methods on six dam sites, the Authors conclude that their reliability closely depends upon the size of the loading device in relation to the spacing of the discontinuities. Attempts to correlate results from different types of in-situ loading tests reveal difficult, because closely depending upon local geotechnical conditions at test location. Plate jacking tests appear to be the most reliable, because involving a relatively large volume of rock. On the other hand, the Scarabée method (“Petite Sismique”) allows a rapid assessment of the deformation characteristics of the rock mass at large scale, and has been found to provide values generally in agreement with those from plate loading tests, while dilatometric or flat-jack tests were found too dependent upon local conditions. The Authors conclude that preference should be given first to the Scarabée method, which uses light equipment and is quickly performed, together with an accurate geological and geotechnical assessment for interpretation. In a second stage, Scarabée shall be complemented by adequately performed plate jacking tests in selected locations, in order to cross-check results and refine the assessment. The general accordance between the results of the two methods, which both can integrate anisotropy of rock masses, justifies this statement.

Jan 1, 2015

By Felipe Henríquez, Daniel Silva

"Traditionally, the implementation of an automated advanced process controller in any mineral processing complex is a challenge, mainly due to the quality of resources and technologies required, the uniqueness of each control solution and the uncertainty of the engineering hours needed to complete the task. Thus, the use of advanced and proven control technology becomes a key factor when deploying the control strategy. However, success would still not be possible without the presence of common sense, process knowledge and fundamental process data. Minera Los Pelambres, taking advantage of such factors and its accumulated process experience, implemented a novel and successful combination of MPC (Multivariable Predictive Control) and advanced control for secondary grinding and regrinding stages at its copper concentrator plant. In both cases, the control objectives are: being capable of processing a variable feed from the upstream process while at the same time avoiding to become a process bottle neck and yet, maintaining an adequate product quality (in terms of size distribution) to the process downstream. Additionally, for the case of the vertical regrinding mill (vertimill), the control system should also be capable of keeping an adequate circulation load and making an efficient use of the available grinding power. In either case, extending hidrocyclones availability while maintaining their performance is a must, since both factors are required for process and maintenance purposes. Thus, the process control problem becomes one with a multi-variable type of process with multiple control objectives to satisfy simultaneously. In trying to solve it, many mineral processing operations have implemented basic or conventional control or even better yet, expert systems. Minera Los Pelambres believes that better and faster results can be achieved using a combination of MPC and advanced control. Such strategy was successfully implemented, reducing considerably process variability while maintaining high throughput and keeping the process well within constraints limits. Their control philosophy, implementation process, main results and their key performance indicators are discussed here."

Jan 1, 2014

MR. McKEEVER: I think we had to start some- where. The proceeds of the beltbuckles and hard hat stickers will certainly be a beginning in a scholarship for some of our young people. And maybe, you know we might even get one of them sometime to go to the University of Oklahoma. A few years ago the luncheon speaker for tomorrow, Brooks Mitchell, got a few of the mine presidents together and we spent a full five hours of just dedicated listening to Carl Terzian. We listened basically on three subjects: how to work with the media, how to work with image, and how to identify with our political systems and those who are in them. I remember that as one of the turning points in my perspective on how our system really works. This gentleman who will be addressing you today, Mr. Terzian, will be conducting about a three-hour session tomorrow. And it's a shame that our other activities will not allow some of the golfers to probably be there. Those of you who can come to the session tomorrow morning will find it most rewarding. A little bit later on we will also have a panel session. And I see all of the panelists are here except for Bob Golten, but I understand that he is registered. We should have a full afternoon session with Charlie and his panel. When we started working on this, we naturally went back to Carl Terzian to give us some guidance. If there is anything wrong with your session, it's my fault because he knows how these should be done and he guided us along the way. One thing that I am sorry, it wasn't his fault necessarily, is that Harry Reasoner will not be with us for lunch tomorrow. Brooks Mitchell is going to make all of the PR he can out of the fact that Harry got scratched and he got in place for him. Brooks gave me one comment along that line. He said, "Do you know what you get when you cross a gorilla with a computer"? Of course I bit on that. He said. "Well, you get a Harry Reasoner." A little over a month ago I was invited out to California to Woodbury University at Carl Terzian's insistence. I happened to be sitting by one of his vice presidents. It was a formal affair. We had to wear tuxedos and everything and Mr.Green was sitting there and he said, "You know," he didn't know who I was at that time, but he said, "You know Carl really didn't want this formal affair. Said he had a couple of friends coming from the coal mining industry and they wouldn't know what to do with tuxedos." So with that Carl, we will start this little session and it's your mike. MR. TERZIAN: Thank you very much Ira. Let me begin by expressing my appreciation to the men and women of the Institute for allowing me to be here. I'm deeply concerned about my reputation, my image and don't want you to get the inference that I am responsible for Ira McKeever's image. Nobody could be responsible for that! But it is a great case in point that we all should be concerned about our images. I guess tomorrow morning from about 8:30. a.m. to about 11:30 a.m. we are going to do a? hopefully, a productive and very pleasant expertence for all of us in this growing field and great interest that people have in the area of image. I happen to be from Los Angeles. I have a national firm which has handled about 600 corporations', over the years through the areas of public relations,' community, civic involvement all built around a strengthening and safe guarding our precious, free enterprise system. And the message that I hope to give you, as you will be eating your lunch today, is really not so much about the image of individuals but as the attitudes built on what Bill Banowsky

Jan 1, 1982

By Bob de Raadt

After a review of the general principles for blasting stacks, the stagnations of two stack demolitions are investigated. The author concludes and demonstrates that MS-delay blasting can be risky under certain circumstances. How this initiation device can still be applied safely to the demolition of stacks is shown in an account of a blasting operation, in which two 106-m (350 ft) -high concrete stacks were involved. The recent discovery of a possible hazard of MS initiation in this field of blasting is an essential contribution to increased safety in blasting tall structures.

Jan 1, 1982

By Laura E. Beverage

The Changes 2008 Brought -MSHA recently posted a PowerPoint to its website which shows statistical performance information for fiscal years 2000 to 2008. -Interesting statistics: Fatality rate in Coal dropped by nearly 30% (.0348 to .0246 per 10,000 workers)

Jan 1, 2009

By J Edmund Hay, Harry C. Verakisl, Richard J. Mainiero, John J. Mulhern

As the first stage in the rulemaking process, MSHA prepared requirements for the approval and use of permissible explosives and blasting items in underground coal mines. These draft requirements known as "preproposals" were announced in the Federal Register in mid-1984. The draft requirements on the use of explosives were written as a revision to Title 30, Code of Federal Regulations, Part 75, Subpart N. The draft requirements for approval of permissible explosives including sheathed explosives for unconfined applications, approval of water stemming bags, approval of detonators and approval of blasting machines were prepared as Parts 15, 16, 17 and 25 respectively.

Jan 1, 1985

By W. H. Pomroy

In its 2001 diesel particulate matter (DPM) rule for metal and nonmetal underground mines, MSHA established an interim concentration limit of 400 micrograms of total carbon (TC) per cubic meter of air (400TCµg/m3), and a final concentration limit of 160TCµg/m3, to be phased in over five years. Following a court challenge to the 2001 rule, MSHA, industry and organized labor reached a partial settlement of the litigation under which the agency agreed to issue a proposal to amend the 2001 rule by, among other things, changing the surrogate from TC to elemental carbon (EC), applying MSHA's traditional hierarchy of controls, and revising requirements for one-year special extensions for complying with the final DPM exposure limit. MSHA issued a final rule in 2005 converting the interim concentration limit from 400TCµg/m3 to 308 micrograms of EC per cubic meter of air (308ECµg/m3) based on a miner?s personal exposure. Pending further rulemaking, MSHA retained the final concentration limit of 160TCµg/m3. In May 2006, MSHA issued a final rule that clarified that the final limit of 160TCµg/m3 would be based on a miner?s personal exposure rather than as a concentration limit. The 2006 rule also phased in the final DPM limit in three steps over two years, beginning in May 2006 at 308ECµg/m3, followed eight months later in January 2007 with a limit of 350TCµg/m3, and finally reaching 160TCµg/m3 in May 2008. Also in the 2006 rule, MSHA committed to converting the 160TCµg/m3 limit to an EC limit in future rulemaking. This paper reviews the DPM exposure limits in the context of the MSHA rulemakings and discusses the DPM engineering controls that were utilized by mine operators to attain compliance with each progressively lower limit.

Jan 1, 2009

By Sakir Selcuk, Brian Hamilton, Paul Zick

The 1.8 mi (2.9 km) Minneapolis-St. Paul International Airport Light Rail Transit Tunnels and Station project is comprised of the underground segments of the 11.8 mi(18.8 km) Hiawatha Light Rail Transit route in Minneapolis, Minnesota. The 21 ft 2 in(6.5 m) diameter twin tunnels were mined 65 ft beneath one of the busiest airports in the United States using an earth pressure balanced tunnel-boring machine. This paper will provide a project overview, review the major equipment selected, tunnel segment casting, and describe excavation and lining operations for the tunnels and station.

Jan 1, 2003

By Nidagal V

This paper discusses the dewatering strategy adopted and the considerations and procedures required to incorporate a dewaterinq scheme into the Mt Whaleback mining operation. It concludes that in pit pre-dewaterinq has successfully allowed mining to progress below the standing water level with the minimum of disruption or radical change to the mining method. It is recognised however, that dewatering is not a static activity and there is a requirement for ongoing investigations and development. Pre-dewatering commenced in October, 1984. Purpose designed pumping trailers have been employed to minimise the loss of pump availability resulting from the frequent. need to remove and reinstall pumps when close vicinity blasts occur. To July, 1986, some 0.5 Mm' of groundwater had been pumped from the unconfined orebody aquifer. Mining has progressed to some 20 m below the standing water level without. any undue water associated problems. Ultimately, it is ,cheduled to extend some 300 in below the original water level in the West Pit. With the development of an increasing area of the mine below the standing water level, the influence of seasonal high intensity rainfall events, which had previously caused little concern, now need to be addressed. Pumping equipment has been designed to evacuate storm water at a rate consistent with mine production Considerations.

Jan 1, 1986