Search Documents

By Kang N. Zhong, Hui H. Luo, Yi H. Wei, Yu L. Wang

"More than 85% of phosphorous reserves in China occur as middle-low grade phosphate of sedimentary origin. The main gangues are dolomite, quartz, silicates, and clays. The characteristics of minerals are finely disseminated. Flotation results have shown that the floatability of apatite of this kind of ore is much worse than that of igneous and metasedimentary origin because of its high specific surface area. Although some effective depressants, such as naphthalene sulfonate and phenanthrene sulfonate, are used to decrease the MgO content in the P2O5 concentrate, its presence is still high (about 2%) in the Chinese concentrates. Meanwhile, the wastewater may cause some environmental problems. Batch flotation results and measurements of specific surface area and CO3 2- have revealed that there is a relationship between the floatability of apatite and the surface area.A two-stage flotation flowsheet, which includes a combination of direct and reverse flotation, was developed for beneficiating sedimentary phosphate ores. The direct flotation was conducted in an alkaline medium and most of the apatite and carbonate minerals floated leaving quartz and siliceous gangue in the sink. In the reverse flotation circuit, the floated product was further beneficiated in an acidic medium to eliminate the carbonate as a float product. Apart from the high quality of concentrate, the two-stage flotation also facilitated the treatment and the recycling of wastewater. A wastewater recycling procedure was developed and tested in a continuous flotation process. The key factor was the careful selection of effective and non-toxic reagents."

Jan 1, 2003

By Lloyd Rowson

??Several factors have led to a review and reoptimization of the Midwest uranium deposit by AREVA Resources Canada Inc., the project operator, on behalf of the owners ??The current proposal is to mine the deposit using open pit methods and then transport the ore by truck on a dedicated road linking the Midwest site with AREVA?s McClean Lake Operation (JEB mill) for processing ??A decision has been made to begin mining the deposit by 2010 (pending regulatory approvals)

May 1, 2008

By Orlando Gallardo

El presente texto describe la implementación del software ADS (Sistema de Despliegue Activo) a los sistemas de control supervisor de los diferentes procesos del complejo metalúrgico a nivel administrativo -en tanto replica los archivos gráficos y de base de datos. Este servidor además de concentrar en su red de campo redundante data de controladores e instrumentos de campo, puede compartir información con clientes usuarios y clientes de visualización dentro de la planta. En ese sentido, el objetivo es simplificar la producción y uso de datos únicos y garantizar la fiabilidad de estos a tiempo real para todos los niveles de supervisión a nivel administrativo, al tiempo que se planea y optimiza los recursos con la toma de decisiones apropiada.

Sep 24, 2008

By Z. Sun

Magnetic fields have been used for inclusions removal from melt and preparation of materials with gradient compositions. Fundamental in these applications is that the induced magnetic forces on the particles/melt can enhance migration and change the interaction behavior. In the present paper, migration and interaction behavior of electrical-insulating particles in a conductive melt under strong magnetic field are theoretically analyzed. It is found that the migration can be considerably enhanced for micrometer sized particles by applying a strong magnetic field. In addition, two forces are involved in the interaction between two particles: the interparticle magnetic dipole-dipole attractive force due to magnetization and the repulsive force induced by flow of the melt. This theoretical analysis renders a better understanding of recent experimental results. Additionally, a new method by using strong magnetic field can be proposed to control the particle size distribution for the preparation of metal-matrix composites.

Jan 1, 2009

By R. J. Bridwell

Acid mine drainage (AMD) occurs in high sulfur coal and heavy metal mining environments. We show remediation methods using 3D numerical ground water flow models and chemical kinetics of pyrite oxidation for acid leaching of pyrite during air and ground water flow. A recently developed numerical model couples air and water flow with kinetics of iron-reactive bacteria, oxygen transport, specific chemical reaction rates, and pyrite oxidation to calculate migration control of pollution. A model is presented which considers diminution of acid mine drainage in pyrite rich ore bodies by raising the potentiometric surface through a vadose zone to reduce acid mine drainage. A ground water model is presented of an initially saturated mountain, containing an adit, with a sloping ground water table. Ground water recharge consists of snowfall and normal precipitation. Simulations indicate that the historically open adit creates a desaturated mountain above the adit. Significant air saturation ranging from 10-90% oxygen can occur to depths of the adit (-270 m). Remediation consists of plugging the adit, which fill s adit and mountain with water from recharge. Plugging the adit required <10 years for resaturation and rise of the water table in the mountain.

Jan 1, 1994

The following data cover a phase in the systematic testing of gold deposits which does not appear to have been specificalIy investigated.In boring either secondary or primary deposits, gold, by virtue of its high specific gravity, will tend to migrate downward, below the driving shoe or bit, and thus cause misinterpretation of value unless final recovery Can be effected after the hole has been bottomed.Unlike fortuitous and non-recurrent errors, due to, say, running ground, &quot;pile driving&quot; or rock fractures, systematic error due to migration may be unpredict.able from operating data alone, and, therefore, result in serious miscalculation of the weighted average upon which the engineer&apos;s recommendation is based.Applied to diamond drilling, loss by downward migration appears to have been largely responsible for distrust of sludge assays in the past. On the other hand, although modern practice rightly trends towards an integration of both core and sludge samples in borehole valuation, the possibility of systematic loss must be investigated when using combination graphs such as those of Longyear, Moehlman and WeIler. If the sludge value is incorrect the combination graphs will serve solely to stultify the core valuation.It appears to be axiomatic that: 1. With full core, sludge assays are of minor import.2. With recovery above 90%, differentjal grinding, of the high grade sections may have occurred, and this c!ln be corrected only by the us.e of cOJ;rect sludge valuation.3. With core recovery less than, say, 70%, no accurate valuation is possible without integrating the sludge assay.4. With less than, say, 10% core recovery, the sludge assay affords the sole basis of evaluating a borehole which may have cost many hundreds of pounds.The conditions demanded for reliable sludge valuation have, in practice, been restricted to high quantitative recovery and return of nearly 90% of the drill water. It is submitted, however, that the following additional knowledge is required:1. The nature of gold distribution in the ore.2. The lifting power of the return water column, which can be gauged by the maximum quartz particle, provided that the degree of &quot;hindrance&quot; can be determined.3. That all gold has been cleared from the bottom of the borehole immediately after it has passed through the orebody.The three cases discussed hereunder are offered not only as proof of the thesis, but also in the hope of promoting discussion on the interpretation of borehole values and on methods for saving free gold in the sludge. The fact that two of them cover alluvial boringand the third diamond drilling has resulted in this attempt to reduce the behaviour of free gold to a basis common to all types of boring.

Jan 1, 1950

By Savita Schlesinger, Mike Hanna, Nathan Scalla, James O’Shaughnessy, Steve Miller

Loudoun Water’s Quarry A (Milestone Reservoir) project involves conversion of a rock quarry to a billion-gallon raw water reservoir. The project includes a new 40 MGD pump station, deep intake shaft, and three drill and blast intake tunnels for accessing the reservoir. Due to concerns regarding constructability and construction risks, the project design was paused while a Construction Manager At-Risk (CMAR) contractor was procured. The CMAR contractor was engaged collaboratively with the design team to provide risk and constructability input for refining the design. Aspects of the original design, design modifications, and benefits of the CMAR collaboration will be presented.

Jun 13, 2023

By E. Fritz

This paper reviews the history, developments and 10 milestones of the oxygen steelmaking processes, with a special focus on conventional autothermic converters, high-speed converters with a blowing rate up to 5 m3n/t min and allothermic converters with coal addition, post combustion and the possibility to increase the scrap rate up to 50%. Related operating results are introduced. A new process route, which is based on hot metal and chromium ore, is outlined. The cost advantage for the production of 304 stainless steel grade is higher than 100 USS/t. The synthesis of EAF and oxygen converter steelmaking, a comparison of decarburization rates, refining combustion burners for optimized oxygen-management in EAF and an example for a large advanced EAF are outlined. Possibilities of flexible steelmaking and the growth and outlook of worldwide oxygen steelmaking are described.

Jan 1, 2004

By Charles De Witt

The ore treated at the reduction plant (called Yangdei) of the Chiksan -Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments conic from Sajunkohl mule, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The overage assay value in gold is $6.95 per ton. At the mine the ore is put into bin,, and is Mien trammed over an 8 per cent. grade to the tipple bins above the mill, where the ore is drawn through the hull holes as desired. The capacity of the tipple bins is about 3,500 tons. On, from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 lb. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore

Jan 5, 1915

By Norman Weiss

THE need for more efficient utilization of labor in the metal-mining industry has been the subject of several recent editorials in the mining press, and one attractive possibility for such improvement lies in the designing of future milling plants particularly with economy of man-power in mind. We are accustomed to think of mill design as the selection and coordinated arrangement of process equipment, but if labor is to be efficiently utilized it must be given early consideration in planning the new mill. There are three good reasons for economizing in labor: (I) to reduce costs, not only in the form of wages but also in housing, hospital, welfare, and other obligations that a company accepts when a new man is added to the payroll; (2) to prepare for recurrent periods of manpower shortage, during which a well-designed plant can manage to get along with skeleton crews; (3) because a milling plant that must depend upon an inordinately large labor force for its operation and maintenance is certain to be inefficient in other respects, for many of the shortcomings in design that make necessary the excessive use of labor are generally not corrected merely by having too many men. A simple example of this is a poorly designed ore-feeding system: if this is inadequate to the extent that one man must be constantly unclogging feed chutes, it may help the situation to put two men or three at this task instead of one, but the feed rate will still be inconstant. First of the factors that affect labor saving is the location of the mill. This is often determined by transportation costs alone, and as a result the mill may be placed close to the mine regardless of the nature of the terrain. The designer must then adapt his layout to the conditions, favorable or not. This happens often at small properties, where capital investment may seem more important than operating expense. In most instances, however, a mill site carefully selected for the advantages it gives the designer in laying out the plant is the most economical in the long run, even if it involves a slight increase in cost of ore haulage. Given some freedom of choice, the design engineer may be able to find just the piece of ground that provides the proper gradient for the needs of the flowsheet, permits installation of essential yards and trackage, and perhaps supplies an excellent site for a tailing dam. Further justification for having placed the mill not too close to the mine sometimes emerges only years later as an opportunity to treat ores from other properties. When it is known from the beginning that the new mill will serve a number of scattered mines, a free choice of mill site is naturally stimulated. The most important single factor in limiting the labor requirements of a mill is its materials-handling system for bring-

Jan 1, 1946

By Robert S. Shoemaker

The development of a metallurgical project is a business venture rather than a technical exercise, and its real objective is to obtain the maximum return on investment consistent with the limitations imposed by company policy and the requirements of society. Demand for profits is the driving force for technical advances and naturally leads to improvements in processes, equipment and plant designs. In the mineral dressing field there have been virtually no new processes developed since the introduction of flotation, and the steady erosion of profits by inflation has been offset only by increasing equipment size. Unfortunately, in recent years, plant designers have not always utilized the largest equipment or the opportunities for functional and economic design presented by the development of larger equipment. Lower cost plants can be developed providing that unrealistic restraints arising from the prejudice of past practices are avoided. As an illustration of this premise, three different approaches were taken toward the design of a clearly delineated but hypothetical copper concentrator of 20, 000 tons per day capacity. While the same flowsheet was used in each case, designs were produced for a conventional plant, an alternate using the largest available equipment, and a third scheme utilizing large equipment and the most functional design which could be developed, including features derived from many plants in many different industries. Capital costs were developed for the three separate designs based on a location in the southwestern United States. Ancillary facilities were identical in each case and included a mine truck shop, a maintenance shop, a general office, and a nominal starter dam for tailings disposal within 5000 feet of the plant. Water supply within 1000 feet of the plant, and power furnished to the property boundary has been assumed in each case. The flowsheet of the three plants is shown in Figure 1 and represents the treatment of a typical sulfide copper ore by three- stage crushing followed by single-stage ball milling. Concentration is by flotation roughing and scavenging followed by regrinding of the concentrates and two stages of cleaning.

Jan 1, 1971

By Craig M. Sams

Matching mill? drives to mill power draws is a relatively new practice with the introduction of variable speed drive arrangements. Semi-autogenous grinding (SAG) mills are the focus of this paper as ball and rod mill characteristics are easily charted as charge loading and speed change. In addition, a look at types of drives available in the market and mechanical ratings is outlined to match the specifics of each drive.

Jan 1, 1991

By G. A. Grandy, P. F. Thomas, C. D. Danecki

When considering the mill drive system for a grinding application, a large number of questions must be answered. Depending on the mill size and type, the mill can be driven by several configurations of drive systems: a single low-speed motor connected to a pinion driving a ring gear, two low-speed motors connected to two pinions and driving a ring gear, or a gearless motor mounted directly. In addition, a gear drive system can have a reducer placed between a high-speed motor(s) and pinion(s) or a power path splitting pinion stand. In some designs the reducer is integral with the pinion stand driven by a high-speed motor. The technical and commercial implications of several mill drive options are presented. Initial cost, cost of installation, cost of commissioning, and cost of operation and maintenance are presented for each drive option considered. The impact of each drive system on the design, cost and operation of the overall plant electrical system is discussed. Also, consideration is given to mill drive availability, and the potential cost resulting from delays in plant production.

Jan 1, 2001

By E. Busse

"Heath Steele Mines Ltd. operates a lead-zinc-copper mining and milling complex in New Brunswick.• During the past seven years, as ore reserves increased, the mill capacity was first expanded to 1,600 tpd and then to 3,000 tpd. In the last expansion, instead of building a completely new 3,000-tpd mill, or adding to existing installations, Heath Steele retained service facilities, buildings, ore bins, Jab, etc., and removed and replaced almost all existing process facilities. Requiring a complete mill shutdown, the expansion had to be carried out in minimum time. Also, new equipment had to fit into existing space. Critical path networks of the project were prepared, a tight schedule for construction was mapped out and progress charted daily to detect problems before they could interrupt the schedule. Heath Steele supervised the purchasing, handling and storage of new equipment, maintained liaison with the engineering contractor and became a sub-contractor, using its own staff to install all flotation equipment and process piping. The 1,600-tpd installation was dismantled and a 3,000- tpd unit was successfully put onstream in 5 months - on time and within budget. One benefit stemming from the expansion: production increased 87 per cent while operating and maintenance labour rose only 8 per cent."

Jan 1, 1972

By R. L. Russell

Production at Freeport Indonesia&apos;s Ertsberg open pit copper/gold mine started in 1972 at a rate of 7500 t/d. Mill throughput remained at that rate for a number of years until the discovery of the Ertsberg East (GBT) orebody. This discovery prompted three successive expansion stages from 1981 to 1988 that boosted production to 20,000 t/d. The discovery of the huge Grasberg porphyry copper deposit in 1988 launched a new era of much larger expansions. The first of these involved installation of a fourth primary mill in 1989 to bring production up to 32,000 t/d and was immediately followed by an expansion of the crushing and screening plant and the addition of a new south concentrator to bring production to 57,000 t/d in 1991. The addition of a primary ball mill and the changeout of the original Denver flotation cells in 1993 has served to optimize current production at a level of 66,000 t/d. A major expansion is now in progress. This includes construction of another new concentrator to house a SAG mill circuit and large Wemco flotation cells in an area created by the removal of 6,000,000t of glacial material. This current expansion, with a planned completion in 1995, will take production to 115,000 t/d. This paper describes the evolution of the Freeport Indonesia (FI) concentrator to-date and will then go into an in-depth discussion of the 66,000 and 115,000 t/d expansions.

Jan 1, 1994

By Robert L. Russell

Production at Freeport Indonesia&apos;s Ertsberg open pit copper-gold mine started in 1972 at a rate of 7.5 kt/d (8270 stpd). Mill throughput remained at that rate for several years until the discovery of the Ertsberg East (GBT) ore body. This discovery prompted three succes¬sive expansion stages from 1981 to 1988 that boosted production to 20 kt/d (22,000 stpd). In 1988, the discovery of the huge Grasberg porphyry copper deposit launched an era of much larger expansions. The first of these was the installation of a fourth primary mill in 1989 that increased throughput to 32 kt/d (35,270 stpd). That was followed by an expansion of the crushing and screening plant and in 1991 the addition of a new south concentrator to bring production to 57 kt/d (62,830 stpd). The addition of a primary ball mill and the changeout of the original Denver flotation cells in 1993 brought production to its current level of 66 kt/d (72,750 stpd).

Jan 1, 1994

By G. Van Weert

Mining project feasibility is projected from a geological model and a mining plan. Ore grade is assumed to be continuous, based on drill hole assays as much as 80 m apart. Eighty meter is 80,000,000 micron. Base metal concentrators may be said to work at 80 micron, for flotation at least. In short, metallurgical and financial performance in green field metal mining is forecast on rejecting waste after comminuting the ore down by roughly a volume factor of 1,000,000,000,000,000,000 (1018) from the feasibility/banking study parameters. This is the gap between mine and mill, between present sulphide mining practices and mineral dressing capabilities, and ultimately between lenders/shareholders expectations and mine/mill performance. By inserting a new upgrading technology in this gap, new opportunities for reserve enhancement and cost reduction are created, and risk could be reduced. Blast holes for extracting the outlined ore might be 8 m apart. Most ore bodies do not abruptly change composition at 8 m intervals; nor are they homogeneous in grade at the 8 cm (3?) rock size, optimum size for sorting. Mining in 8 m blocks will inevitably cause dilution of the mill feed and ore losses in the waste rock. This is well recognized in the mining industry. Much work is going on applying the vast data storage and manipulation capability of computers to mine scheduling. One only has to consult the SME Annual Meeting presentations. At the 2007 Meeting, Clark and Dagdelen described the challenges faced by Newmont at its operations and the application of sophisticated software tools and methods in its search of solutions to mining optimization. Block models can often contain in excess of one million blocks. Additional complexity exists when multiple grades are modeled for each block. The authors identify the main optimization problem as the system?s ability to cater to large scale problems in an acceptable timeframe; in other words, still larger computers are needed. At the same Meeting, Menabde et al (2007) presented a new pit development planning tool called Blasor, developed by BHP Billiton Technology, and its co-developed Blasor IPD (In Pit Dumping), (Zuckerberg et al (2007)). For purposes of this paper, Blasor/IPD incorporates options on processing capacity constraints and blending targets, eliminating arbitrary up-front decisions about cutoff grades for each block of material in the extraction sequence.

Jan 1, 2008

By V. Svalbonas

Everybody has an opinion what the quality of a grinding mill head casting should be, yet extremely few take the time, or get the opportunity, to compare their opinions against fitness-for-purpose data. The real question is not how flawless the casting should/could be, but rather how long will ?this? casting survive in operation. To validate an opinion on this topic one needs either extensive historical data, or comprehensive experimental data, or preferably, a combination of both. The same data can also be used to establish the conservativeness, or lack thereof, of analytical prediction methods.

Jan 1, 2009

By G. H. McKay

AT the Eagle mine, near Gilman, Colorado, where the Empire Zinc Company have installed an underground mill, transportation problems were comparatively simple. A railway siding on the Denver and Rio Grande railway is equipped with an unloading dock or platform at the portal of their service incline adit to the mill. This 18-degree incline is approximately 600 feet long from the unloading track to the head of the mill skipway. For the Big Missouri mill, upwards of 2,500 tons of material and equipment had to be trucked from tidewater at Stewart, B.C., a distance of 21 miles to the Big Missouri camp at elevation 2,800. From that point, this freight had to be moved either over or through the Big Missouri ridge, rising to elevation 3,450, to its final location 800 feet from the surface between elevations 2,150 and 2,350. Immediately after leaving the government dock at Stewart, the road crosses the International boundary line into Hyder, Alaska, and then follows a water grade for eleven miles along the lower stretches of the Salmon river. leaving the river, the road climbs for two miles before crossing back into British Columbia territory at Silver Heights, and then continues for another mile and a half to where the Big Missouri road branches off from the main road to the Premier mine. For a distance of four miles from the junction of the roads, the Missouri road is very narrow, with many sharp curves and with irregular up and down pitches and grades up to 25 per cent until it reaches the Summit. From there on, a fairly easy grade leads a mile and a half to the end of the road on Joker Plats. In winter, the last stretch of road is subject to heavy snow drifting, especially through a narrow funnel-shaped gulch, known as &apos;The Gap&apos;, where the snow may pile up to a depth of over twenty feet.

Jan 1, 1938

By Michel Fontaine, Bruno St-Cyr

"The mission of the CENTRE DE RECHERCHE INDUSTRIELLE DU QUEBEC (CRIQ) is to stimulate economic development by guiding businesses in their pursuit of innovation.With a comprehensive approach to their needs, CRIQ provides businesses with expertise based on the most recent developments and insights in the fields of:Research and Development ServicesAutomation and production processesDevelopment of industrial equipmentEnvironmental biotechnologiesTesting and Product Qualification Services Industrial and Technological Information ServicesConsultancy and competitive intelligence servicesIndustrial information bankStandardization ServicesElaboration of standards and product certificationSystems registrationEXPERTISE COMPETENCE, INNOVATIONSince its founding in 1969, CRIQ has been involved in over 100,000 projects. The results of its research and development services have enabled it to build over one hundred pieces of equipment, almost all still in operation today. CRIQ has been and remains the driving force of innovation and expertise on the industrial scene, offering highly competitive solutions to a clientele from numerous industrial sectors.CRIQ became a crown corporation operating on a commercial basis on June 30, 1997. This change in its corporate structure has enabled it to put a marked emphasis on trade and implement an array of new operational practices.The formation of marketing companies with private partners, the opening up to corporate business and international markets, the new directions for internal research and the strengthening of its marketing component are among the activities CRIQ has initiated over the last fiscal year to finally reach its cruising speed."

Jan 1, 2000