Search Documents

By A. W. Jolliffe

AEROPROSPECTING may be defined as the application of the air view to the search for mineral deposits. The term is suggested as a preferable alternative to either aerial prospecting (which may be confused with areal prospecting) or air prospecting. The air view may be obtained by visual observation from an aircraft or by examination of air photographs; each has its particular advantages and disadvantages. Aeroprospecting should be regarded only as an aid to, and not as a substitute for, accepted prospecting methods ( l ). The Precambrian region north of Great Slave lake consists of two well defined physiographic units, a feature first noted by J. T. Wilson (2). The boundary between these lies close to the north shore of the east arm of the lake and extends northwesterly near Spencer, Beniah, Carp, and Ghost lakes (Figure 1). South and west of this line, exposed bed-rock makes up the greater part of the land area; eskers are very rare, and overburden is largely limited to rock-walled valleys and depressions. North and east of the line, outcrops are rare or absent, eskers are abundant, and most of the surface consists of drumlin-like drift hills, elongated parallel to the direction of ice movement (Figure 2). Where this boundary passes through the area shown in Figure 1, it lies near the 1,200-foot contour and may mark the maximum extent of the lake or sea arm present in this vicinity toward the end of the Pleistocene period. For convenience, the first area may be called the 'bed-rock belt' and the other the 'drift belt'.

Jan 1, 1945

By F. Heivilin

Little did I know, in 1977, that when the A. P. Green Refractories Raw Material Manager showed me 5-6 burlap bags with samples of calcined high alumina bauxite in their testing lab that this was the start of China moving to be the number one user and producer of calcined refractory bauxite. According to Ted Dickson in his August 2008 Industrial Minerals article China produced about 4 million tons of calcined bauxite in 2007 using 2 million tons themselves. They imposed an export limitation of 970,000 tons in 2007 and 940,000 tons in 2008. A 10% growth will take up the difference between exports and production in 4 years. Two of these years are gone. It will take only 4 more years to eliminate the export quota in home use. Then they will be importing unless they increase production. Guyana was exporting over a half million tons in 1975 and sold less than 70,000 tons in 2002. Basai Metals Group bought Guyana?s deposits and is rose to 250,000 tons in 2007 and expects to produce 280,000 tons in 2008. PRICES According to the USGS Prices dropped from $172/per ton for Guyana calcines in 1980 just after the start of Chinese production to $122 in 1985. Guyana prices averaged around $120/ton from 1985 to 2005. China?s price dropped as low as $45/ton in 1995 undercutting Guyana and making it virtually impossible for anyone to get into the market. The price suddenly escalated to $550/ton FOB China in the summer of 2008 when China actually cut its exports in half. The price dropped in the fall as orders dropped. This is a four to five fold price increase. Is this a shortage of bauxite or a monopoly? Australia dropped out of the market in 2008 and Surinam, controlled by Alcoa, is not participating right now. Will these two come back in to make up the difference? Will the price hold up so they can make a profit? [ ] The low prices have undoubtedly affected the prices of the 60 and 79% alumina bauxite which can hold down the quantity of 80% plus calcined refractory needed in the world market. China is starting to upgrade lower quality bauxite up to 90% alumina. With high prices kaolin alteration to high alumina comes into play. The calcined bauxite is also used for proponents, Brown fused alumina, and abrasive grades which compete with Refractories. These and the tightness of supplies needed for metallurgical will hold prices up. TONNAGE China is the number one supplier and consumer of high alumina calcined bauxite in the world. Basai Metals Group Guyana (BMGG) is owned and controlled by Basai Minerals Group of China. This appears to be the second largest supplier. Australia has dropped production and Brazil is just starting to expand. It appears China is going to replace some of exports caused by the Export License 940,000 ton maximum in 2008 by raising Guyana?s (BMGG) production of calcined refractory grade bauxite. Companies exceeded restriction in 2007. Fines have been imposed for 2008. In August 2008 they appear on line to meet the 2008 quota. After August prices have dropped off as orders dropped due to the recession. Guyana was the largest producer in 1975 with 769,000 tons which decreased to less than 79,000 tons in 2002. The U. S. is a small part of the world production. I have used the United States charts to represent world imports because I have little data on what other countries import and pay FOB for their bauxite. China started exporting calcined 80% plus refractory bauxite to the United States in 1979 with 24,000 tons. By 1985 they were the number one importer with 169,000 tons. Guyana who had been number one in shipments to the United States gradually decreased to 36,000 tons in 2006. Guyana has been purchased by China BMGG and will increase there production to over 200,000 tons in 2009. Australia shut down production in 2008 and Surinam has elected to not send any Calcined bauxite to the United States. Imports to the United States from 1978 to present are as follows: [ ] Refractories are important because they affect 96% of the GNP. During the cold war we had stockpiles of 80% refractory grade bauxite

Jan 1, 2009

The Board of Directors, at its meeting on March 22, 1918, extended an invitation to the American .Institute of Metals to become the Institute of Metals Division of-the American Institute of Mining Engineers in accordance with the terms of By-Law VII. This invitation was presented to the membership of the American Institute of Metals for letter ballot, and, at the meeting of the Board of Directors of the American Institute of Mining Engineers on April 26 191 ,it-was reported that the replies had been in favor of accepting the invitation. The American Institute of Metals therefore becomes a division of this Institute and the members thereof are entitled-to all privileges of regular

Jan 6, 1918

By C K. Bell, L. S. Collett

An AFMAG survey was flown in 1968 over the Upper Nelson River area, Manitoba. The flight direction was northwest-southeast and flight spacing was 2 miles. In the Cross Lake Subprovince, AFMAG showed that an isolated peridotite outcrop was part of a dike that extended over 80 miles. Diabase dikes are not always marked by an anomaly, but isolated cross-overs, when used in conjunction with geological and magnetic data, permit their extrapolation. Anomalies coincide with areas of sulphide mineralization. In the Flin Fion Subprovince, known and unknown northeast-trending faults are detected. The Berry Creek fault was extended south through Tramping lake, then under the Paleozoic cover. Conductors were detected at, or near, the axes of major synclines within Amisk and Snow Group sediments. Granitic terranes have low conductivity and, because they are characterized by smooth AFMAG profiles, they can be delimited. AF.MAG is being recognized as a geophysical method that can aid geological mapping and interpretation. Its most important contribution to the geologist will be in regions where out-crops are sparse.

Jan 1, 1971

By Steve Kral

The Society for Mining, Metallurgy and Exploration’s origins can be traced back to 1871. This was when 22 Pennsylvania coal mining engineers founded the American Institute of Mining Engineers (AIME). The organization’s objective was to “promote the arts and sciences connected with economic production of the useful minerals and metals, and the welfare of those employed in those industries by all lawful means.” Metallurgy and Petroleum were added to the AIME name in 1919 and 1956, respectively. Divisions of AIME were formed throughout the following years in recognition of the increasing trend toward specialization among mineral industry engineers. At the time, SME’s divisions consisted of the Coal Division (1930, now known as the Coal and Energy Division), the Industrial Minerals Division (1935), the Mineral and Metallurgical Processing Division (1948) and the Mining and Exploration Division (1949). The Environmental Division was created in 1997.

Jan 1, 2007

By Gunther Schimmel

Ag exudation in four different alloys (Ag-Cd, Ag-Sn, Ag-Sn-In and Ag-Zn) is characterized. The amount of exuded material is correlated with the volume increase due to oxide formation in dependence of the alloy concentration and different densities of the oxide and matrix phases. It is shown that all four alloys show similar amounts of volume increases, but different amounts of exuded material. It is concluded that internal stresses due to the volume increase cannot be the dominant driving force for Ag exudation. A gradient in the chemical potential of Ag that originates from the O concentration gradient inherent to internal oxidation is suggested as driving force. The exudation behavior is thus governed by the variation of the activity of Ag in the Ag fcc phase in the Ag-Me-O system that differs between the alloying systems.

Jan 1, 2010

By É. Roberge, S. Makni, G. Gagnon, F. Lavoie, A. Faucher

"Feed particle size is an important variable for the primary grinding mill operation. Several commercial vision systems have proven to successfully measure online many types of ores and are used for automatic control. However, due to limitations associated with segmentation algorithms, these systems fail to provide good measurements when the feed is composed of a specific bimodal particle size distribution: very big rocks and a large amount of fine particles. This is typically the case for crushed iron ore. This paper presents a technique to overcome the limitations of existing vision systems by using 3D cameras and appropriate processing methods. It provides online particle size distribution indicators and bulk volume flow rate measurement. It is designed to be very cost-effective, robust, precise, easy to install and to maintain. The 3D system was validated in two iron ore processing plants and the results clearly show that it can be used to optimize primary grinding mill operation where 2D segmentation vision systems fail.INTRODUCTIONFragmentation measurement using digital image processing has successfully been applied in mining and mineral processing operations. Several maintenance and operating applications are already deployed in the industry: Measurement of rock fragmentation after blasting (Maerz, 1999; Palangio, 1999) (Pragyan, 2012) Truck inventory (Palangio, 2005) Monitoring of crusher mantle wear Automatic control of crushers and SAG mills (Bouajila, 2000) (Bartolacci, 2001)Commercial technologies like WipFrag (Maerz, 1999), VisioRock and others proved to be very efficient to precisely measure the particle size distribution of many types of materials. These products are mainly composed of a camera, a lighting system and an image processing system based on a segmentation algorithm. By controlling adequately the lighting conditions and with periodic maintenance on the segmentation algorithm calibration parameters, it is almost always possible to achieve reliable measurements.However, the segmentation algorithm is not adequate when the particle size distribution contains big rocks and a large amount of fine particles. In this case, the area containing the fine particles is accounted as a big rock while big rocks get segmented as multiple smaller sized particles, leading globally to a wrong measurement. This situation prevails for crushed iron ore and coke, among other materials. Figure 1 shows a picture of a material which is typically very difficult to process through segmentation techniques."

Jan 1, 2015

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012

By José Arce

El sistema AG-DAS entró en operaciones en 2015 y su aplicación tiene diversas ventajas sobre el método de polarización inducida convencional. El concepto del sistema fue el uso de múltiples receptores de dos canales, que registran la señal completa con sincronización de tiempo por GPS. La tecnología DAS (sistemas de configuración distribuida, por sus siglas en inglés) brinda mayor confiabilidad en la detección y modelamiento tridimensional de mineralización metálica con geometría compleja a profundidades de hasta más de 800 metros.

May 22, 2019

By Hui Lu

The structural changes in solutionized AA2618 during natural aging and their effects on subsequent artificial aging were investigated by hardness measurements, X-ray diffraction, differential scanning calorimetry and transmission electron microscopy. The changes in lattice parameter and hardness during natural aging indicate that copper-enriched clusters form in the earliest stage, followed by the formation of magnesium-enriched clusters and coppermagnesium co-clusters. Prior natural aging consistently weakened the hardening during subsequent artificial aging at 180, 200 and 230 °C but had no effects on artificial aging at 150 °C. The decreased age hardening was attributed to the reversion of small clusters/zones that formed during prior natural aging. The lattice parameter exhibited erratic changes with increasing artificial aging time, reflecting the complex sequence of the reversion and precipitation.

Jan 1, 2006

By D. B. Swanepoel

Hulamin Rolled Products (Ltd) developed a high Mn and Si containing alloy, EN 4017 as a scrap consuming alloy from the waste generated in producing their range of clad products for brazing of inter alia automotive heat exchangers. The multifaceted composition of this alloy (Al -1.2 wt% Si -1.1 wt% Mn -0.2 wt% Mg-0.26 wt% Cu) suggested that it might display some degree of strengthening via precipitate formation of the Mg2 Si-types. The aging isotherms constructed showed that EN 4017 with 0.19% Mg reached a lower peak strength (YS~210 MPa and UTS~260 MPa)compared to the EN 4017 material with 0.43% Mg (YS~270 MPa and UTS~325 MPa). The higher Mg variant of EN 4017 was comparable with the age-hardenable reference alloy EN 6061. Selected area electron diffraction (SAED) studies proved that the microstructure of age hardened EN 4017 contained a combination of ß', ß" and U2 phase after being aged at 175ºC for 65 h. The general microstructure contained precipitate free zones as well as grain boundary Si films, although these did not lead to significant embrittlement. The role of Mn dispersoids in the fracture mechanism of 4017 is also discussed. The article will compare the behaviour of EN 4017 with that EN6061. Keywords: Age-hardening, dispersoids, magnesium silicide, precipitate free zones

Jan 1, 2009

By Finley A. Campbell

THE Quemont and Horne mines are located at Noranda in north-western Quebec. As shown in Figure 1, the Noranda area lies between the Cadillac-Bouzan fault zone on the south and the Porcupine-Destor fault zone to the north. Both of these major structural lineaments appear to be geometrically, and possibly genetically, related to the Grenville Front. The regional geology has been discussed by Wilson (12), Cooke et al. ( 2), and others. The geology in the Noranda vicinity, as compiled by Dugas and Gilbert ( 3), is shown in Figure 2. The Cadillac-Bouzan fault zone separates the dominantly Temiskaming-type sediments in the south from the Keewatin-type canic rocks to the north. These volcanics, which vary in composition from rhyolite to andesite, form a broad anticlinorium with a general eastward plunge. A succession of dioritic stocks, sills and dikes have been mapped in the area. The principal granitic rock masses include the Powell, Flavrian and Dufault stocks.

Jan 1, 1962

By A. A. Levinson, M. B. Kirkley, J. J. Gurney

"Scientific advances in the past decade have greatly clarified our understanding of certain concepts relating to the age and origin of diamonds. These advances are largely the result of geochemical studies of mineral inclusions in diamonds, made possible by modem analytical techniques which enable the accurate chemical analysis of micro-sized particles of the order of 200 microns in maximum dimension. As a generalization, the inclusions indicate that most diamonds formed from either of two rock types, peridotite and eclogite. Peridotitic diamonds have yielded ages of 3300 million years, whereas eclogitic diamonds areyounger and rangein agefrom approximately 1000to 1600million years. Kimberlite and lamproite, the two rock types usually associated with diamonds, typically are much younger than the diamonds they contain. Thus, it is now dear that kimberlites and lamproites are only the transporting mechanisms which brought diamonds to the surface and are in no way related to the formation of most diamonds. The latest concepts which developed during the past decade regarding the sources of carbon for the crystallization of diamonds from peridotite and eclogite, and the mechanisms of kimberlite and lamproite emplacement, IntroductionThe decade of the 1980s has seen major advances in our understanding of the age, origin and emplacement of diamonds. The information presented herein is applicable to virtually all natural diamonds, excluding diamonds related to meteorite impacts. There is still some question, however, as to the applicability of the new information to industrial grade ""fibrous"" or ""coated"" diamonds, and to microdiamonds (< 1 mm). In addition to drawing upon our own experiences, this review is summarized from a voluminous literature and for those interested in the original sources we recommend the books by Mitchell and Bergman (1991), Ross (1989), Nixon (1987), Mitchell (1986), Glover and Harris (1984) and Dawson (1980), and the review articles by Mitchell (1991), Gurney (1989) and Meyer (1985).are also discussed."

Jan 1, 1992

By E S. Bernard

Toughness testing of fibre reinforced concrete (FRC) at 28 days age is typically undertaken as part of quality control for the many applications where fibres are used in concrete, including shotcrete, tunnel segments, and cast-in-place tunnel linings. The performance achieved at 28 days is usually assumed to be retained with increasing age. However, as the average strength grade of concrete used in most tunnelling applications, including tunnel segments, has steadily increased over the last 20 years, this assumption is becoming increasingly unviable. This is because for some types of fibre the mode of post-crack fibre behaviour depends on the strength of the concrete and can change from a desirable high-energy pull-out mode to a low-energy rupture mode as the strength and age of concrete increases. This paper describes a series of trials performed over two years in which the American Society for Testing and Materials (ASTM) C1609/C1609M beam tests were used to assess the performance of FRC reinforced with two widely used brands of steel and macro-synthetic fibre. The hooked-end steel fibres used for half the beams exhibited a dramatic fall in performance beyond 56 days age as the mode of failure changed from pull-out to rupture. The other fibre did not exhibit a fall in performance with age. This phenomenon highlights the need to quantify performance of FRC at much later ages when long-term performance is required, for example, to resist seismic events or changes in ground stress due to nearby excavations. As an alternative, a reduction factor may be applied to the performance of FRC mixes for which evidence of satisfactory long-term performance is not?available.CITATION:Bernard, E S, 2014. Age-dependent changes in post-cracking performance of fibre-reinforced concrete for tunnel?segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 229–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By William Fink

MANY investigators have attempted to determine the true nature of the internal changes taking place during aging. Merica, Waltenberg and Scott1 were the first to propose a theory of age-hardening. They attributed the age-hardening of duralumin to the precipitation of minute particles of the compound CuA12. Later Zay Jeffries and R. S. Archer2 augmented the above theory by suggesting that the small CuA12 particles acted as "keys" causing "slip interference." Many other investi-gators3 have devoted much time to the mechanism of age-hardening, some corroborating the "precipitation" and "slip interference" theory, others coming to different conclusions because of effects that to them seemed unexplainable by the early theories; e.g., the increase of electrical resistance upon aging, the fact that no change in lattice parameter could be detected during the early stages of aging even at elevated tempera-tures, and the fact that the density did not change as would be predicted. In 1932, Merica revised4 his earlier precipitation theory to take care of these presumably anomalous effects. This revised theory, the "knot" theory, assumes that substantial age-hardening occurs before actual precipitation of solute as discrete particles. The assumed mechanism is one of diffusion of solute atones into groups forming distorted regions which act as "hard" spots and cause slip interference. These "knots" are assumed to have approximately the same lattice arrangement as the solvent.

Jan 1, 1936

By F. R. Hensel

Up to the present time few attempts have been made to produce hard nonmagnetic materials by heat treatment of austenitic steels. The usual result has been to cause them to pass into the martensitic stage, thus destroying to a great extent the typical austenitic properties, since this involves a transition of a portion of the iron from a face-centered to a body-centered type of atomic arrangement. High-strength nonmagnetic materials such as might be provided by properly hardening austenite are required in the electrical industry for different machine parts. In Europe nonmagnetic retainer rings for restraining the end-turns of the rotor windings in turbo-alternators have been developed as a special application of high-strength austenite. In testing1 a 28,000-kva. three-phase Siemens turbo generator running at 3000 r.p.m. at full load current, the losses in the short-circuit test were 450 kw. for the magnetic ring and 286 kw. for the nonmagnetic, and the difference should be attributable to the magnetic ring. The differences in temperatures during the same test are given in Table 1 and these show the advantage of a nonmagnetic over a magnetic retainer ring.

Jan 1, 1931

By V. Labiouse, M. Souley, N. Lafrance, C. Auvray

"Chalk rocks have been used for centuries as a strong building material and for the production of lime. The shallow underground room-and-pillar quarries where the chalk was extracted are now abandoned and endure the effects of time and weathering, increasing their risk of collapse. The risk of instability, involving natural or anthropic underground structures, is an issue for more than 10 000 towns in France.In order to investigate the causes of underground quarry collapse and to aid prevention strategies, we carried out a study of the physico-mechanical behaviour and ageing of chalk in abandoned pillars in two underground quarries, in situ-instrumented by INERIS, in the Parisian Basin, France. Core samples were drilled horizontally from pillars in the Saint-Martin-Le-Noeud dolomitic chalk quarry (Oise, France) and the Estreux glauconitic chalk quarry (Nord, France).Uniaxial tests were performed on dry and saturated cylindrical plug samples extracted perpendicular to the cores at regular distances along their lengths. Physical and mechanical properties were obtained. The dolomitic chalk (Saint-Martin-Le-Noeud) exhibits variation in mechanical and physical properties with horizontal pillar depth. Both density and compressive strength seem to increase outwards from the pillar-core to the pillar-wall. This is the opposite of that would be expected from a purely mechanical point of view. SEM analysis revealed progressive degradation and homogeneity of the grains from the edge to the inside of the pillar. At the pillar wall, the crystal faces are well-defined, almost euhedral, and the grains are of variable size. In contrast, at the inside of the pillar, crystals are finer-grained and are anhedral with highly degraded edges. In the physico-mechanical tests and SEM analyses performed on the Estreux samples, no significant variation was observed between the pillar-walls and pillar-core. However, dissolution marks were observed along the entire length of the half-pillar core."

Jan 1, 2015

By Daniel Valente Guimarães

Este trabalho tem como objetivo apresentar os resultados alcançados através do planejamento, por meio do agendamento com hora marcada, no processo de expedição de produtos acabados, que estão permitindo a Votorantim Siderurgia atratividade na contratação de veículos, redução de custos e confiabilidade no processo.

Aug 17, 2017

By I. Nikolic

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By R. Hogg

The sedimentation and dewatering characteristics of flocculated slurries are determined by the size and density of the flocs. Studies of the formation and growth of flocs reveal that floc size is limited by breakage of the agglomerates due to shear in the suspension. Floc density measurements indicate that there is an inverse relationship between size and density. This relationship appears to be determined primarily by the nature of the solid particles, especially the size distribution, but it appears that agitation of the suspension can lead to some densification of the flocs, in addition to breakage. It follows that both size and density can be controlled to a significant extent by regulating the physical conditions (agitation, method of flocculant addition etc.) during flocculation. The use of physical floc conditioning to control the sedimentation and dewatering (filtration) behavior of flocculated, fine-particle suspensions is evaluated in terms of its effects on floc size end density.

Jan 1, 1986