Search Documents

By ZHANG Ting

In view of the high consumption and contamination of traditional vanadium extraction technology, a new process of leaching the converter vanadium slag without roasting with titanium dioxide waste was proposed. Extraction mechanism of P204 in the leaching solution had been researched and single factor experiments show that after a prereduction of Fe, and under conditions: ambient temperature，leaching solution original pH=2.5, phase ratio (A/O)=1:3, shaking time 8min, the extraction rate of V is more than 98.62% meanwhile the separation rate between V and Fe is up to 135.3 in the 20%P204-10%TBP-Sulfonated kerosene extraction system.

Jan 1, 2015

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Army Research Laboratory (ARL) has an interest in the recovery and processing of rare earth elements. At Montana Tech, elevated temperature chlorination of rare earth oxides is presently being investigated as a potential methods leading to the selective separation and recovery of rare earth elements from mineral ores and concentrates. After preliminary evaluation, ytterbium oxide was selected as a representative surrogate material for more extensive chlorination studies. Methods used to determine the conversion and recovery include X-ray diffraction (XRD) and inductively coupled plasma (ICP) analysis. These data have been used to establish and confirm process conditions that consistently yield high conversion efficiencies. Based on the promising results, further experimentation is underway to ascertain the metallurgical response of other rare earth oxides and carbonates to the roasting process. The end goal is to create a robust process for industrial application that has greater efficiency and reduced costs as compared to current practice.

Jan 1, 2015

By Mei-le He, Min Chen, Xiang Shen, Lei Xu, Lei Liu, Nan Wang, Xue-liang Yin

In the current study, Al2O3-MgO-CaO refractories were prepared at 1400-1600 by the addition of MnO micro-powders, and the effect of MnO addition on densification behavior of the refractory was discussed. The results showed that the doped MnO dissolved to MgAl2O4 phase, and promoted the growth of MgAl2O4 grains by the formation of MgAl2O4 solid solution. As a result, the dense microstructure was obtained, with the apparent porosity decreased from 19.2% to 5.4% and the bulk density increased from 2.78g/cm3 to 3.15g/cm3 after firing at 1600 for 2h by the addition of 4% MnO. In addition, a texture microstructure was observed, which is considered to be favorable to improve mechanical properties and the service life of Al2O3-MgO-CaO system refractories.

Jan 1, 2016

By Zhucheng Huang, Ronghai ZHONG, Tao Jiang, Jun ZOU

The method of reduction roasting and magnetic separation of low-grade, micro- fine disseminated refractory iron ore following granulation with coal produced unexpected success. Pellets of iron ore with diameter between 3 and 8mm were granulated with coal, bentonite and water. The raw pellets and reduction products were analyzed by scanning electron microscopy and x-ray diffraction. Results show uniformly distributed coal powders inside the pellets improved the kinetics of the reduction process and accelerated the reduction rate. Reduction time was higher at temperatures below 890℃, which resulted in the formation of substantial amounts of fayalite. When temperature was increased, micro- fine hematite was then quickly reduced to iron metal and the amount of fayalite decreased sharply. When pellets were reduced at 950℃ for 25min, reduction products with 56.73% metallization rate were obtained. After grinding and magnetic separation, a concentrate with 72.18% Fetot was obtained.

Jan 1, 2015

By Ting Liu, Qian Li, Peng Deng

The wastewater containing Hg2+ and Pb2+ does great harm to the environment and human bodies. Traditional wastewater treatment cannot fundamentally put a stop to heavy metals pollution for producing secondary pollution. In this paper, Hg2+ and Pb2+ in wastewater were removed and recovered by sulfide precipitation- flotation. Sodium sulfide was used as precipitant and butyl ammonium aerofloat was used as collector. Results indicated that Hg2+ and Pb2+ could be reduce to less than 0.03mg/L and 0.16mg/L respectively by both coprecipitation- floatation and fractional precipitation- floatation. In these two methods, fractional precipitation flotation could not only remove Hg2+ and Pb2+ from wastewater, but also could recover mercury and lead effectively. The infrared spectrograms showed that the adsorption between butyl ammonium aerofloat and mercury precipitate or lead precipitate is chemisorption.

Jan 1, 2015

By Chuanfu Zhang

Based on Thermogravimetric and Differential thermal analysis (TGA-DTA), porous copper powder is prepared by thermal decomposition of complicated copper oxalate. The effects of various conditions on the morphology, crystalline grain size and specific surface area of copper powder were investigated, including temperature, duration, mixing ratio of nitrogen and hydrogen. Furthermore, composition and morphologies of the products were characterized by X-ray diffraction (XRD), Scanning electron microscope (SEM) and BET adsorption isotherm. It is found that porous copper powder was produced under optimum conditions. The specific surface area is over 6.74 m2?g-1, and average pore size in particles is about 30.3 nm. After comparison of SEM images, the final product Cu well inherits the morphology of the precursor, thus a mechanism of in-situ decomposition is proposed.

Jan 1, 2009

By Chonghe Li, Xionggang Lu, Wei Xiao, Xingli Zou, Weizhong Ding

The reduction degree and rate of the initial ilmenite concentrate and pre-oxidation samples by hydrogen were investigated by using thermogravimetric analysis system. H2-TPR was used to detected reduction properties of the pre-oxidation products which were oxidized at different temperatures. The phase transformations and micromorphology changes during pre-oxidation and hydrogen reduction were identified by XRD and SEM. The FeTiO3 was decomposed into TiO2 and Fe2O3 at the temperature below 900 oC. With the temperature rising, Fe2TiO5 was the only stable phase in high temperatures. The reduction of pre-oxidation ilmenite concentrate was faster than the natural sample, which was attributed to the micropores generated on the surface of ilmenite concentrate during oxidation. The main phases of the reduction product were metallic iron, ferrous pseuodbrookite.

Jan 1, 2014

By Tobias Dubberstein, Hans-Peter Heller

The viscosity of Fe-Cr-Mn-Ni TRIP/TWIP (Transformation Induced Plasticity, Twinning Induced Plasticity) steel with varied nickel content is investigated using a vibrating finger viscometer. The viscosity of the melt is calculated from the change in power input in the field coil by an immersed finger into the liquid steel to maintain a constant peak-to-peak amplitude of the sine wave of oscillator compared to the idle state. Nickel content in steel is varied from 3 wt% to 9 wt%. The dynamic viscosity (η) at 1600 °C for 3 wt% Ni is 3.73±0.14 mPas, for 6 wt% Ni 3.50±0.03 mPas, and for 9 wt% Ni 3.93±0.09 mPas. There is a kink from low to high nickel content in viscosity values of Fe-Cr-Mn-Ni alloys. This phenomenon can be explained by a change in coordination number in the melt, as reported for Fe-Ni binary system in literature. The availability of viscosity data delivers relevant input to model free fall atomization processes of FeCrMnNi alloys.

Jan 1, 2015

By Jianjun Wang, Jiaqing Peng, Lingen Luo, Zhenbang li, Yinghe Lin

Copper removal from ferronickel by FeS has been exploring studied. It is found that the decopperizing agent FeS makes the copper removal in ferronickel effectively. The effects of FeS addition amount, carbon content in ferronickel and experimental temperature were investigated. The results showed that the removal rate of copper in ferronickel increased with the amount of FeS increasing. When the dosage of FeS is 20% (mass percentage)，the removal rate of copper can reach higher than 11%. The rate of copper removal rises with the amount of carbon content increasing in ferronickel. When the amount of carbon content is 1.86%, the removal ratio of copper is 41.3%. Higher experimental temperature promotes the copper removal reaction in certain extent. The flux is acidity and weak oxidative can also promote the reaction of copper removal.

Jan 1, 2015

By Paul S. Korinko, Simona E. Hunyadi Murph

To address a radiological contamination event, a materials and process project was initiated. During the course of this project, processes and materials were developed that successfully captured zinc vapors physically and chemically, respectively. However, the physical traps were placed in an undesirable area and it was determined that the chemically captured zinc reactions was reversible. Consequently, advanced nanomaterials are being developed to capture zinc vapors. The current state of the art of the science and engineering of these materials and their efficacy for zinc capture and retention is discussed in this paper.

Jan 1, 2015

By Cong Wang, Siyang Long, Pengcheng Zhang, Haibin Zuo

The present study describes central segregation of the High-carbon steel billets of 150mm square and its heredity to the following hot-rolled wire rods, whose sizes are 10mm and 6.5mm in diameter separately. The relationship between center segregation of the billets and solute element distribution of rods, the mechanical properties and microstructure of rods were studied experimentally. The results show that segregation index of C is higher than that of Mn. With the increase of central segregation, the stability of the mechanical property of the rods becomes worse. The formation of carbide network and central martensite in the rolled products can be attributed to the heredity of the as-cast central segregation. The 6.5mm-diameter-rod has higher tensile strength than that of 10mm diameter which might be due to bigger reduction ratio. Thermo Mechanical Control Process (TMCP) should be used together with Billet Centersegregation- controlling (BCSC) to improve the overall properties of rolled products effectively.

Jan 1, 2016

By XING Xiangdong, Zhang Jianliang, MA Jinfang, WANG Zhenyang

The non-equilibrium reflux reaction behavior of phosphorus was studied with synthetic slags formed by using the AR chemical reagents and changing the initial condition of basicity, FeO, MgO and Al2O3. Due to increase of viscosity, the dephosphorization slag with high basicity inhibits the full contact of slag with iron, which leads to the low reaction rate in the early stage. However, since the high basicity improves the activity coefficient of CaO, the dephosphorization rate and phosphorus capacity goes up in late reaction stage. FeO promotes the increase of reaction rate in early dephosphorization stage. But the polarization force of Fe2+ is stronger than Ca2+, which hinders the reaction between phosphate ion and CaO and reduces the stability of PO4 3-. Thus, high content of FeO will adversely impact on dephosphorization reaction. In addition, MgO has a promoting effect to the dephosphorization, whereas Al2O3 has a negative influence.

Jan 1, 2016

By Jianguo Yin, Wenqiang Yang, Xiaoli Yuan, Juan An, Wentang Xia

Low grade iron ore with phosphorus (LGIOWP), a raw and wasted industrial solid material was used as an adsorbent to remove Pb(II) from wastewater. The effects of initial pH value, adsorptive time, initial Pb(II) concentration, adsorptive temperature and LGIOWP dosage on the Pb(II) removal efficiency were studied. The results show that the Pb(II) removal efficiencies exceed 99.4% and Pb(II) concentrations are less than 0.30 mg/L under the conditions of pH value 7.0, adsorptive temperature 50 oC, adsorptive time 30 min, initial Pb(II) concentration 100 mg/L, particle size <0.25 mm, adsorbent dosage 5 g/L and stirring speed 260 r/min. After Pb(II) removal reaction, the Pb(II) concentrations of wastewater completely accord with the requirement of national discharge standards of pollutants from lead and zinc industries (GB 25466-2010) (TPb= 0.5 mg/L) in China. Therefore, it can be concluded that LGIOWP is a new low-cost adsorbent which is suitable for the adsorption of Pb(II) from wastewater.

Jan 1, 2015

By Huimin Lu, Zhijiang Gao

Reduction reaction can happen among Al, V2O5 and TiO2 powders. Al can deoxidize metal V and Ti from the metal oxides. The electric igniter can be used to trigger the reduction. The reaction between Al and V2O5 is very intense and release large amounts of heat, but the heat which is needed to initiate the reaction between Al and TiO2 is not enough. These two reactions have been initiated first and V-Al and Ti-Al alloys can be obtained with a higher metal recovery percent. Through adjusting the ratio of Al, V2O5 and TiO2 powders, the system which combines these two reactions can ensured enough heat to react. KClO3 is added to the system, as the ignition agent, in order to make the reaction much complete. Finally, Ti-Al-V alloys can be obtained and need remelt to adjust the constituents.

Jan 1, 2016

By Lin Li, Wen Shi, Hua Wang

"Specimens of the ultra-low carbon bake hardening steel were soaked for 1 min to 5 min, and then cooled by water quenching. The internal friction experiments were carried out to detect the spectra of the specimens. Results show that Snoek peaks are present in all the specimens, however, an obvious Snoek-Koster peak is found only in the 5 min-annealed specimen. Besides, tensile results indicate that the bake hardening values increase with the annealing time prolonging from 1 min to 3 min, but decrease as the annealing time prolongs further to 5 min. The solute distributions in the specimens were characterized by three dimensional atom probe. Some segregated C and V are found in the 1 min-annealed specimen, and the C and V contents decrease as annealing time prolongs to 5 min.1. IntroductionAs an excellent member of automotive body panel materials, various types of bake hardening (BH) steels have been developed since 1980s. Bake hardening property, as one of the most important mechanical properties, has been studied by many researchers [ 1-5]. As is known, BH phenomenon is generally controlled by the interaction between solute C and dislocations. The Snoek peak of internal friction (IF) is very popular in the investigation of solute C [6-9]. However, result of internal friction cannot suggest the distribution pattern of solute C as well as its influence on BH phenomenon.Three dimensional atom probe (3DAP) can diagnose solute element atoms as well as nano-sized precipitates, and it is the only instrument that currently can identify the identities of individual atoms in a material and measure their spatial coordinates with the resolution close to 0.3 nm [10]. There have been a number of studies about using 3DAP to detect solute elements as well as nanometer sized precipitates [11-19]. For example, Hono et al. [16] used 3DAP to determine the solute elements in an age-hardened Mg-Ca-Zn alloy, and they also obtained the distribution patterns of the observed elements."

Jan 1, 2011

By K. M. Parida

The kinetics of dissolution of manganese dioxide in dilute sulphuric acid solution have been investigated using iron pyrites as a reductant. The dissolution rate of manganese is independent of the speed stirring but depends upon temperature, particle size, specific surface area of manganese ore, acid concentration, Fe(II) concentration and amount of pyrite. The activation energy is 43.6 KJ/mol and the linear relationship between the rate of dissolution and lido indicates that the reaction is chemically-controlled. The redox reactions of MnO2 with iron pyrites and Fe(II) are the rate-controlling reactions.

Jan 1, 1990

By Maria K. Kojo

The interaction between various slags and a nickel concentrate containing pyrite, pentlandite, and violarite were investigated by submerging concentrate pellets in molten slags. The slags were contained in MgO-A12O3 spinel crucibles. The slag oxidizes the iron sulfides in the concentrate, resulting in a nickel matte. The amount of S02 gas formed during reaction was measured to determine the oxidation reactivity of the slags. The experimental variables included temperature, the ferric/ferrous ratio of slag, and other slag properties such as the FeO/SiO2 ratio and the MgO and NiO contents. The reactivity of the slag depended in a complex manner on its oxidizing power, viscosity, and interfacial tension. The slag composition for the greatest reactivity was determined to be Fe3+/Fe2+ = 0.3, Fe/SiO2 = 1.3, and % MgO = 2. This slag, however, caused substantial foaming. Increasing the MgO content to 10% or replacing it by 5% MgO + 8% NiO eliminated at a slight decrease in reactivity. The implications of the findings from this work in the bath smelting of nickel sulfide concentrates are discussed.

Jan 1, 1995

By Nobuo Takahashi

Effective solvent extraction media have been investigated for purification of rare earths. At first, a quaternary ammonium compound was studied. The counter anions of rare earths and organic dielectric substances were tested to improve separation factors,. And second, crown ethers were selected for extractant. Several diluents of crown-adducts were tested to improve solubility and distribution coefficient as well as the counter anions of rare earths. Especially, in the presence of strong reducing agents, highly selective extraction of europium from other rare earths was observed. The third extactnts were ß -diketones. Presence of organic dielectric substances was very effective to improve separation factors. Though those. three groups of extractants were suitable for mutual separation of light rare earths, alkyl esters of alkyl-phosphonic acids were suitable for mutual separation of heavy rare earths because of their high separation factors. To keep proper pH value was necessary for acidic extractants, so control method of the solution pH was studied with high molecule insoluble amines or salts of those.

Jan 1, 1995

By Katsutoshi Inoue

Pectic acid gel crosslinked with epichlorohydrin was found to have very high selectivity to lead(II) and iron(III) ions over zinc(II) ion compared with commercial weakly cation exchange resins containing the same carboxylic functional groups, suitable for removing small amount of impurity metal ions from waste zinc plating solutions. In order to lower the cost, new adsorption gel was prepared from orange juice residue containing pectic acid by crosslinking with epichlorohydrin, which was also found to be suitable for removing these impurities. Further, very cheap adsorption gels was prepared not only from orange but also from apple juice residues by a simple method through just saponificating pectin substances contained in these residues into pectic acid by calcium hydroxide followed by water washing and drying. These adsorption gels exhibited excellent adsorption behaviors for removing the impurity metal ions away from zinc.

Jan 1, 2003

By Michael Altepeter

Big River Zinc Corporation, located in Sauget, Illinois, operates a neutral leach residue circuit. The residue produced in the circuit is sold to lead smelters for subsequent recovery of valuable metals. A research program was initiated several years ago to find a means of treating the residue at Big River Zinc to recover the valuable metals. The Ausmelt submerged lance reactor was selected as the best alternative for the first step of the process. Pilot scale tests were conducted at Ausmelt&apos;s facilities in Melbourne, Australia. Separations were excellent. 99%+ of the Zn, Pb, Cd, and Ag contained in the residue reported to the oxide fume. 99%+ of the SiO2,, Fe, Mg, and Ca in the residue reported to the slag which passed the EPA TCLP test. Subsequent leaching of the oxide fumes and purification of the leach solutions using conventional procedures produced solUtions suitable for zinc electrowinning and an upgraded lead sulfate cake for sale.

Jan 1, 1992