Search Documents

By Rak-Jun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEOs. Efficient blue light-emitting diodes (LEOs) were fabricated using InGaN/GaN triangular MQWs. The LEOs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEOs at 20 rnA and 20 "C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LEO, but decreased substantially in the rectangular one.

Jan 1, 2003

By E. F. Vegman, Ndabezinhle Dube

"In the practice of conventional sintering, production is always afflicted with the problem of being unable to get a uniform quality of produced sinter in the bed. Invariably the top layer of the sinter cake is composed of weak but highly sinter, while the bottom layer is over-fused, forming a sinter that is very strong but less reducible. These symptoms point to a variable distribution of the heat balance in the process of sintering which results in a deficit of heat in the top layers of the sinter bed and an excess of heat in the bottom layers, due to an increasing input of regenerated heat in the heat balance down the bed. This causes losses in the productivities of the sinter machine and the blast furnace.The current work was designed to improve on the solution to the above problem through the establishment of a more accurate combustion zone heat balance of the sintering process. This development is mostly on the method of determining the regenerated heat input in the overall heat balance. Previous methods were based on the assumption that the width and the velocity of the combustion zone remain constant through out its whole life, which is not the case since tests have shown that both its width and velocity increase as the combustion zone moves down the bed. In this work, these factors have been taken into account. Tests and calculations using the model were carried out for haematite and limonitic ores. The high sensitivity of the model to changes in the sinter mix composition and sintering conditions was demonstrated.The results present the following prospects:• The minimum theoretically possible coke breeze consumption during the sintering of any type of iron ore fines, under any sintering conditions, can be established.• The model can be used to control the metallurgical quality of the sinter in any point in the sinter bed since calculation data includes desired basicity, combustion zone temperature and FeO content in the sinter produced."

Jan 1, 2001

By B. C. Jena

Activities of carbon, cobalt and nickel were evaluated in the ternary systems iron-carbon-cobalt and iron-carbon-nickel for the temperature range 1300-1600°C for cobalt and 1300-1700°C for nickel. The carbon activities were determined from the knowledge of activities (1) in the binary system iron-carbon, (2) in the dilute ternary systems and (3) from the knowledge of carbon saturation data. The activities were mathematically expressed with the Taylor series expansion of Wagner's interaction parameter formalism modified to suit concentrated solutions. The cobalt and nickel activities were determined from the knowledge of carbon activities by applying the Gibbs-Schuhmann integration and from cobalt and nickel activities in the binary systems iron-cobalt and iron-nickel. Partial molar enthalpies of mixing were determined based on the temperature behaviour of the activity coefficients.

Jan 1, 1992

By L. M. Abrantes, A. P. Paiva

"A brief review of some innovative methods for the direct recovery of metals from loaded organic phases is presented; emphasis is given to electroreductive stripping and cementation, which are described and illustrated by examples: of current research. The recovery of silver using a two-phase electrolysis - by direct application of an electrical potential to a mixture of a metal loaded organic phase· containing Cyanex 471X, obtained by solvent extraction, and a stabilized sodium thiosulfate solution - is more extensively discussed. The overall efficiencies are analyzed and compared with data obtained by conventional stripping procedures. Some preliminary results achieved for the recovery of the precious metal using galvanic stripping, applied directly to similar organic solutions and involving zinc and iron powders as reducing agents, are also evaluated.Introductory ReviewThe application of hydrometallurgical methods to the recovery of metal values from ores and concentrates has been receiving a growing interest, either from researchers or from the mining industry [1].For the concentration / purification of the relatively low concentrated metallic solutions resulting from the leaching of those raw materials, solvent extraction (SX) is a well established technique [2]; the loaded organic solvent is then conventionally contacted with a suitable aqueous solution, the metal in its final form being usually recovered from this solution by electrowinning.As an efficient and / or selective stripping is sometimes difficult to achieve, depending on the specific characteristics of the system under consideration, some alternative procedures have been analyzed in order to overcome this problem. One of the chosen routes, mainly developed by Hirai and Komasawa, is to promote the reduction of the desired metal species in the organic phase, in such a way that the stripping stage becomes feasible; for the selective stripping of vanadium from a solvent containing a mixture of vanadium and molybdenum, the authors successfully used reductive [3], electro-reductive [4,5] and photo-reductive [6] techniques. The two latter methodologies have also been applied to the recovery of europium from a solvent containing europium, samarium and gadolinium [7,8].However, further processing is necessary to recover the metal in its solid state; therefore, methods causing the direct reduction of the metal species in the organic phase to their fmal metallic form would be of interest, as an intermediate step would be avoided"

Jan 1, 1997

By Tom Lewis

The metal finishing and electronic industries are searching for ways to recycle materials · and reduce costs. The areas of heavy metal waste and water recycling has gained new interests with the potential of impacting the operation's bottom line. Lewis Environmental Services, Inc. has completed numerous heavy metal recovery and effluent recycling projects with its ENVIRO-CLEAN PROCESS for government and private sector clients. This patented process utilizes a proprietary chemically treated granular activated carbon with enhanced heavy metal adsorption capabilities combined with electrolytic metal recovery to produce a saleable metallic product. The process generates no sludge or hazardous waste and the effluent meets EPA .limits. This paper covers several heavy metal removal projects, two fullcscale commercial installations, and one treatability case study.

Jan 1, 2000

By William Petruk

An investigation was conducted to determine whether mineral liberation data obtained by one image analysis technique are the same as data obtained by another image analysis technique. The liberated vs non-liberated, volume % and weight % techniques for measuring mineral liberations by image analysis were tested. The results show significant differences between the values obtained by the different techniques. The lowest liberation values were obtained by the liberated vs non-liberated technique and highest by the weight % technique. It is interpreted that the weight % technique produces the most realistic results. The weight % technique also produces data that can define mineral associations for the unliberated grains. These include (1) mineral quantities in particles that contain different amounts of unliberated mineral, (2) mineral quantities in particles that have different size ranges, and (3) mineral quantities and degrees of liberation for specific minerals in particles of different size ranges.

Jan 1, 1996

By Zeng Zheng, Liu Chen, Yu Xing-Fu, Tian Su-Gui, Zhang Chao

"Single crystal nickel-base superalloy is prepared by using the various withdrawing rates. By measuring creep properties and microstructure observation, the influence of the element segregation on creep properties of the superalloys is investigated. Results show that the dendrite spacing and the segregation extent of the elements decrease with the enhancing withdrawing rate. The superalloy with smaller dendrite spacing has lower segregation of the elements and better creep resistance. The dislocations climbing over the rafted y’ phase is thought to be the deformation mechanism of the alloy during steady state creep. In the later stage of creep, the fact that some dislocations shear into the rafted y’ phase may twist the rafted y’ phase. As the creep goes on, the initiation and propagation of the cracks occur up to occurring creep fracture, which is thought to be the fracture mechanism of the superalloy during creep.1. IntroductionSingle crystal nickel-based superalloys consist of high volume fraction of ?? strengthening phase and ? matrix, and possess the excellent high-temperature mechanical and creep properties, therefore, they have become the main material to make the blades of the advanced aeroengines[1-3]. Some literatures report that the temperature-bearing and creep-resistance properties of the single crystal nickel-based superalloys can be remarkably improved as the increases content of the refractory elements, such as W and Re[4-6]."

Jan 1, 2012

By Florian Kongoli

The behavior of cobalt as a by-product in the NilCu smelting and converting processes effects directly the quality of the final products as well as the revenues gained from the overall process. An effective way to evaluate and predict this important behavior is thermodynamic modeling which reduces the time and the cost of experimental investigation. In this work a thermodynamic model of cobalt-containing matte phase in NilCu smelting and converting processes is presented. The model predicts a priori the thermodynamic properties and phase relations of the ternary and multicomponent matte based solely upon the optimized parameters of the binary systems. This model can be used with other models such as those of slag, metal, gas etc. to predict various aspects of cobalt behavior such as matte- slag, metal-slag distribution, etc.

Jan 1, 1999

Proposed by outstanding electrochemist and electrometallurgist Prof. Raphael Agladze (191 1- 1989), process of copper and manganese co-electrowinning was enhanced to the pre- electrowinning stages: low,temperature co-leaching of copper and manganese containing materials, and to high-temperature co-roasting of the same materials with consecutive leaching. The report presents results of experimental investigations of the processes mentioned above, as well as results of thermodynamic investigations of co-roasting processes, and co- leaching processes computer modeling.

Jan 1, 1997

By Michael A. Lllga

Electrically Switched Ion Exchange (ESIX) is an approach for ion separation that combines Ion exchange (IX) and electrochemistry by utilizing electro active IX films to provide a selective, reversible, and economical separation method that greatly reduces secondary waste generation compared with conventional ion exchange. Studies on the development of films with improved stability and capacity and their use in continuous flow systems for ion separations will be. reported. Both technical and economic evaluations demonstrate ,the viability of once-through or batch recycle waste processing with ESIX.

Jan 1, 1999

By Jianxin Zhang

A process, in which arsenic in the residue is transformed directly into scorodite and copper dissolves into the solution simultaneously, was studied. The process was carried out in acidic ferrous sulfate solution under oxygen pressure. The optimum conditions of the process were determined as follows: the initial H2SO4 concentration of 10 g/L; liquid/solid ratio of 10; Fe/As molar ratio in the feedstock of 1; the addition of calcium lignosulphonate was 1% of sludge; oxygen pressure, temperature and reaction time were 1.5 MPa, 150 °C and 6 h, respectively. Under these conditions, arsenic transformed to crystalline scorodite in size of 5–10 μm, and the transformation efficiency reached 97.60%; meanwhile, the copper was leached with a high efficiency of 93.34%. The stability of the leaching residue was evaluated by TCLP testing, and the results indicated the concentration of arsenic in the leaching solution was extremely low as 0.04 mg/L and met the standard of safe stockpile.

By G. Coryell, S. Blaskovich

"A computer model has been developed to simulate the flash furnace and converter operations at the ASARCO Hayden Copper Smelter. The focus of the modeling was to optimize the converter operation to eliminate high matte level episodes in the flash furnace. These episodes (reducing feed to the furnace) resulted from the lack of converter operation scheduling. The model provided ""what if?"" scheduling scenarios that led to increased efficiency of the converter and flash furnace operations.This paper discusses alternatives studied to optimize the converter operation and the development of the computer modeling program, including implementation of the project. The discussion details the results of the project including the conversion from batch to a real time converter scheduling process. IntroductionASARCO's Hayden Smelter consists of a fluid bed drying system, an Inco oxygen flash smelting furnace, Peirce Smith converters, two anode furnaces and two casting wheels, gas cleaning plant, 2800 stpd sulfuric acid plant, 650 stpd oxygen plant and 200 gpm water treatment plant. The process flow sheet of the plant is shown in Figure 1.Over the past several years, the Hayden smelter has been involved in productivity improvement and cost reduction programs. This has been necessary to become a low cost copper producer in today's market. Part of the productivity improvement program was the use of process control to streamline the flash furnace and converter operations. Process control, through the use of computers and electronic controllers, has played an increasingly important role in optimizing processes in the Hayden Plant since the startup of the Inco flash furnace in 1983."

Jan 1, 1989

By Wenxian Zhu, Xuema Li, Patrick R. Taylor

"Experiments were performed in a non-transferred arc, thermal plasma flow reactor to investigate the synthesis of ultra fine boron nitride (BN) powder from the reaction system of boron oxide (Bz03), methane (CH4), ammonia (NH3) and hydrogen (H2). Argon (Ar) and nitrogen (N2) were used as plasma gases. The thermodynamics and kinetics of the synthesis reactions were examined and a chemical reaction mechanism was proposed. The powders produced under certain operating conditions had high purity and good conversions. All the products were extremely fine powders (< 30nm) and were uniform in size distribution. The powder products were analyzed by chemical and physical characterization. The effects of the reaction variables on the conversions from B203 to BN and the purity of the products were investigated.IntroductionIn the past few decades, boron nitride (BN) has attracted a great deal of interest because of its excellent thermal, chemical and electrical properties (1-4) It has a high thermal stability and thermal conductivity. Chemically, it is very stable and is not wetted by most molten metals and slag. It is also an excellent low loss insulator. Since hexagonal boron nitride (h-BN) is light in weight, strong and easily fabricated, it has applications in a variety of specialized high temperature areas, such as a high temperature lubricant, crucibles for molten metals, thermocouple protection tubes, break rings for horizontal continuous casting of steel, and friction reducing coatings. In cubic form, boron nitride is one of the hardest materials known, second only to diamond, and it is an excellent material for tools in which the use of carbon based materials is limited by oxidation or reaction with metals."

Jan 1, 1998

By Pekka Taskinen

The converter-less nickel matte smelting technology (DON) adopted more than 20 years ago in Boliden Harjavalta smelter has been since that applied successfully to the processing of large number of nickel sulphide concentrates of various Ni-to-Cu ratios and MgO contents. The operational point of the technology is far from the conventional primary nickel smelting in the smelting-converting route. Therefore, a careful scouting of distribution equilibria of the base and trace elements in the smelting conditions of DON process has been conducted, in order to obtain quantitative information about the equilibria and thermodynamic properties of the nickel mattes at low iron concentrations, less than 10 wt% [Fe] in matte. The series of investigations has included novel experimental and analytical techniques for increasing the reliability and sensitivity of the phase equilibria as well as the element distribution observations carried out in typical high-grade nickel matte smelting conditions.

By Shawn A. Cefalu, Matthew J. M. Krane, Kent J. VanEvery

"Segregation during electroslag remelting (ESR) of a nickel-chromium-molybdenum alloy (Ni-8 wt% Cr-25 wt% Mo) has been modeled. Features of the model include species transport and AC electromagnetic effects coupled with fluid flow, heat transfer, and solidification. The effect of varying ingot diameter and melt rate, on macrosegregation patterns, local solidification time, and liquid pool profiles obtained from this model are demonstrated. The results show that the macrosegregation in the ingots correlates to the filling velocity.IntroductionElectroslag remelting (ESR) is a secondary melting process used to refine the chemical composition and the microstructure of metals. Macrosegregation of solute elements causes defects in ESR ingots, including freckles and the maldistribution of phases. These defects are not correctable through heat treatment due to the large length scales over which they occur. However, the frequency and distribution of these defects may be minimized, or even prevented, through process control based on an understanding of the conditions that lead to their formation.In the past, studies have been conducted on the effect of the process parameters on the shape of the melt pool and the thickness of the mushy zone [1-7]. In these studies, the shape of the liquid pool is determined by consideration of the heat and fluid flow induced by electromagnetic (Lorentz) force and thermal buoyancy. The transport of solute and the resultant solutal buoyancy effects were not considered in these macroscopic models. Defect formation is tied to formation of secondary phases (e.g., freckling and white spots in nickel superalloys) [5,8]. In cases where secondary phase formation is calculated (e.g., [6]), phase fractions are determined using a micro-scale model given the local solidification time (LST) and local thermal history from the macroscale model.Using the local thermal history from the macroscopic transport model to predict microstructure increases the importance of the accuracy of those results. This investigation models the macrosegregation of molybdenum during the ESR of a Ni-Cr-Mo alloy. The effect of macrosegregation on pool shape and depth is demonstrated, along with its effect on the local solidification time. By comparing the relative effects of the melt rate and ingot radius, a better understanding of the factors that affect macrosegregation, and ultimately secondary phase formation may be obtained."

Jan 1, 2004

By P. Rooney

In due course, new smelters will have to be installed in order to meet the increasing worldwide demand for copper. This paper presents the results of a study made for the purpose of identifying the most desirable countries in the world in which to locate a new smelter. Both sociopolitical and economic factors were taken into account. Criteria developed and methods used to assess each possible location are described. The study indicated that the most interesting potential locations are Canada, -Chile, Portugal and the USA for new copper smelting complexes.

Jan 1, 1983

By Tuula Mäkinen

One of the latest applications of the Outokumpu Flash Smelting Technology is the direct smelting ,of nickel concentrates to metallised low-iron nickel mattes. Compared to the conventional nickel smelting, the new DON process needs a lower number of smelting vessels resulting in considerable economic and environmental benefits. Fundamentals of smelting nickel concentrates in one stage to low-iron mattes are presented. Properties of nickel. smelting slags with an emphasis of the slag fluidity at high MgO-levels are also discussed. Conditions prevailing in DON mattes at high oxidation degrees are presented as well as their influence on the behaviour of such mattes in the settler and on tapping the furnace. Distributions of elements in the direct smelting are presented and compared with the conventional process. A further comparison is made with pilot-plant data and the industrial scale.

Jan 1, 1998

By E. Allain

Extraction of basic metals from sulfides by conventional pyrometallurgical processing leads to the emission of SO2. To avoid this inconvenient, low temperature selective chlorination of sulfide concentrates could be an alternative. However, such process generates hazardous chlorides SxCly. A part of sulfur chlorides such as SCI2 can be recycled as a chlorinating agent of metal sulfides. Hydrolysis of sulfur chlorides, using a solution containing Na2S.9H2O, led to the recovery of more than 90 pct of elemental sulfur. Reduction of SxCly by hydrogen was investigated between 300 °C and 800 °C. About 70 and 90 pct of elemental sulfur were recovered from SC12 and S2C12, respectively. A flow sheet for the chlorination of metal sulfides and the treatment of sulfur chlorides was suggested.

Jan 1, 1998

By Shuqiang Guo, Xionggang Lu, Yuyang Bian, Weizhong Ding, Lan Jiang, Kai Tang, Changyuan Lu

For recovery of rare earth elements from the NdFeB based permanent magnet scraps, a high temperature process was used. Permanent magnets scraps were firstly oxidized in air. The optimal oxidation conditions under air are at temperature of 700oC holding for 30min. After the oxidation process, the oxides were reduced by graphite crucible at 1500oC under Ar atmosphere. By this way, the rare earth elements were recovered in the form of oxides, and Fe was separated to the metal phase. Boron distributed in both the rare earth oxides (REO) containing slag and the metal phase. In order to reduce the boron contents in the rare earth oxides, the carbon saturated iron bath and NdFeB added carbon saturated iron bath were used to refine the slag. By this process, the rare earth oxides with a comparatively high purity of 98.2% were gotten.

Jan 1, 2015

By I. M. Richardson, M. Janssen, I. J. Bennett, V. A. Popovich

The most critical processing step during the manufacture of screen-printed crystalline solar cells is firing aluminium and silver contacts, which generates residual stresses and solar cell bowing. In this paper, an alternative Ag contact formation mechanism is proposed and aspects related to electrical contact properties, residual stresses and layer delamination are investigated. It is found that there are two main processing parameters affecting the uniformity and delamination of the Ag/Si interface, namely the peak firing temperature and the silicon surface roughness. Silicon surface polishing gives a better wetting of the silicon surface by the glass layer, resulting in a good contact and lower incidence of large voids, compared to the case of highly textured surfaces. The non-uniformity in the glass layer and large voids at the Ag/Si interface (in the case of a textured surface) are expected to have a negative effect on the mechanical strength of the solar cell.

Jan 1, 2015