Search Documents

By B. Madelin

Over the last ten years, Minemet Recherche and Metaleurop have used an approach in order to investigate and improve the operation of its Smelting furnace and its lead blast furnaces. This approach gives importance- to three complementary means of investigation : - Probing campains in the industrial furnace (temperature and gas analysis profiles), - Chemical and physical modeling (coke combustion, sinter reduction modes, flows patterns, ?.) , - Staged mass and heat balances or kinetic model. This allows to define the limits of operation of each blast furnace and to predict the influence of operating parameters on the furnace performances. For the zinc Imperial smelting furnace, the probing results show the existence- of both an Isothermal reserve zone at 1015ºc and a chemical equilibrium between ZnO and gas which makes possible the use of a practical model for heat and material balances. In particular, very good prediction on the influences of operating parameters can be made. On the contrary, for lead blast furnaces, the probing results show that the thermal and chemical equilibria are not reached. Consequently, classical models for staged heat and mass balances are not sufficient. The use of the other means allows then to characterize the specific influences of operating parameters on the thermal instabilities of these furnaces and their allowed limits.

Jan 1, 1990

Numerical simulation of the fluid flow and heat transfer has been carried out for a waste-heat boiler in an Outokumpu type copper flash smelter. In this boiler, SO2-containing off-gas flows into the waste-heat boiler radiation section at about 1350°C. A fraction of cooler off-gas from the electrostatic precipitator at about 200°C was recirculated into the radiation section, and a small amount of ambient air was leaked into the boiler from the bottom. The computational results show that the flow is strongly recirculating and distinctly three dimensional in most of the boiler, particularly in the radiation section. The hot off-gas cooled down rapidly after entering the radiation section due to radiation. The predicted flow pattern and temperature distribution were in a good agreement with laboratory models and industrial measurements.

Jan 1, 1995

By John R. FitzPatrick

The separation and purification of uranium from either nitric acid or hydrochloric acid media tan be accomplished by using either solvent extraction or ion-exchange. Over the past two years at Los Alamos, emerging programs are focused on recapturing the expertise required to do limited, small-quantity processing of enriched uranium. During this period of time, we have been investigating ion-exchange as a method for extraction/purification of uranium from acidic media. In addition, waste stream polishing is associated with this effort in order to achieve more complete removal of the uranium prior to recycle of the acid. Extraction chromatography has been demonstrated' to further polish the uranium from both nitric and hydrochloric acid media thus allowing for a more complete recovery of the actinide material and creation of less waste during the processing steps. We will discuss contact experiments for evaluation of eleven different resins for uranium removal from nitric acid, the evaluation (again by contact experiments) of uranium elution from the ion-exchange media by various chemicals, and small-scale experiments for the removal of 235U from nitric acid. Larger-scale (100-gram) flow experiments using depleted uranium, were done after the small-scale evaluation Of the selected resin. A discussion is also included concerning the shortcomings of the contact experiments and how the flow experiments were modified in order to overcome these problems. We will also discuss the application of ion-exchange for some specific process needs at Los Alamos Contact experiments were used to evaluate some commercially available solvent-impregnated resins in addition to evaluation of several resins of this type synthesized in our laboratory. These experiments' involved both nitric and hydrochloric acid media. The data from these experiments will be used to determine the column size and' amount of resin required to polish the waste stream produced by the ion-exchange process described above. Small-scale flow experiments will be described and data given on the mass balances achieved using this two step process. Future work for evaluation of new ion-exchange and solvent-impregnated resins as well as the search for new eluants will be discussed. Other future experiments for both processes, including large-scale experiments, will be discussed in detail.

Jan 1, 1996

Segregation roasting tests were carried out on Zaire cobalt oxide ores assaying about 2% Co and 3.5 to 6.5% Cu. The major parameters tested during the laboratory investigations were temperature, dosage and type of reducing agent, dosage and type of chloridizing agent, and particle size. Results showed that standard conditions suited to the segregation of copper ores, i.e. low temperature and low dosages of reducing and chloridizing agents, resulted in the segregation of copper only, while conditions suited to the segregation of lateritic nickel, i.e. higher temperature and increased dosages of reducing and chloridizing agents, led to a successful segregation of both copper and cobalt. Under the best conditions, 88% of the cobalt and 98% of the copper could be recovered in a concentrate assaying 32.5% Cu and 8.5% Co. Alternatives to process such a concentrate are briefly reviewed.

Jan 1, 1993

By P. K. N. Raghavan

This paper identifies potential technologies for Carbon dioxide abatement from the mining and metal industry with special reference to the Aluminium industry. Mine reclamation could contribute to this effort to successfully reach the greenhouse gas (GHG) emissions reduction commitments for a nation. An overview of GHG production by the mining and metal industry together with a review of principles used to set the context in which specific options for GHG reduction are described. Options for GHG reduction in the mining and metal industry include reforestation, Addition of soil amendments or neutralizing agents, CO2 capture and storage, initiatives towards energy reduction, waste heat recovery and alternative energy use. An analysis and quantification of the potential GHG reduction of potential carbon sinks and sequestration options for the mining and metal industry are provided. Cost estimates for different options are provided. The paper also identifies sources that could fund research regarding GHG reduction options. The paper concludes with recommendations.

Jan 1, 2011

By Sergey Shabala

Green leaf tissues convert solar energy into the energy of chemical bonds of sugar molecules during the process of photosynthesis. The efficiency of this conversion can be much higher than efficiency of any of the currently known silicon-based solar panels. Importantly, vast amounts of CO2 are assimilated during this process. The efficiency of photosynthesis is critically dependent on the availability of a large number of nutrients, among which metal cations such as K, Ca, Mg, Cu, Zn, Fe, Mn, and Ni play a key role. In this paper I summarize basic requirements and major functions for each of these essential nutrients in plant photosynthesis, both at the whole-plant and molecular level. I will talk about how these requirements may be affected by the global climate trends and discuss the prospects of creating artificial photosynthetic “bioreactors” for efficient energy conversion and CO2 assimilation.

Jan 1, 2009

By P. M. Tyroler

Inco operates a hydrometallurgical plant to treat the residue from the pressure carbonylation process. The main constituent in the residue is cop¬per. The residue is leached under pressure in an acid sulphate solution in two stages and the copper is recovered via electrowinning. The electrowinning tankhouse is fully integrated into the overall plant flowsheet as spent elect¬rolyte is required in upstream leaching steps. In recent years, the amount of residue had increased and copper removal capacity became the rate limiting factor for the entire plant. Consequently, a major program was undertaken to upgrade the tankhouse with regards to capacity, efficiency, cathode quality, working environment and structual integrity and appearance. This paper will describe current facilities and operation, and detail progress in our up¬grading efforts.

Jan 1, 1987

By Batric Pesic

Reactions of metallic iron were studied in several different aqueous solution systems: water, medium salt solution used for the growth of T ferrooxidans, ferric iron solution and solution containing T ferrooxidans. Each system was studied under abiotic and biotic conditions in the presence of T ferrooxidans and as a function of pH, particle size of iron powder, temperature, ferrous and ferric iron concentrations. It was found that metallic iron reacts with water differently than does with ferric iron in water. Surprisingly, T ferrooxidans were non-functional in the dissolution of metallic iron. Also, the reactions of metallic iron with pure water were indistinguishable from the reactions with water containing medium salts for bacterial growth. The reactions with ferric iron were also independent of medium culture compounds. The mechanisms of metallic iron reactions with ferric ions are different from the mechanisms of metallic iron reactions with water.

Jan 1, 2001

By W. G. Davenport

This chapter examines three minor influences on flash smelting's industrial oxygen and oil requirements, i.e.: (a) recycle of molten converter slag to the flash furnace (b) gangue oxides and carbonates (e,g, Ah03, CaC03) in the flash furnace feed (c) minor sulfides (e.g. NiS} in the flash furnace feed. It then examines the. sensitivity of our flash furnace calculations to previously ignored aspects of smelting chemistry -Cu, S and Fe304 in slag and 0 in matte.

Jan 1, 2001

By S. Yuan

Oxygen ion conducting yttria-stabilized zirconia (YSZ) tube was used to remove oxygen from molten Cu at 1373K. Outer surface of the tube was in contact with the melt and the inner surface containing a thin layer of porous Ni-ZrO2 cermet electrode was in contact with a reducing gas. The migration of oxygen species (O2-) from the Cu melt through the YSZ tube is accompanied by an equal and opposite flux of electrons maintaining electroneutrality. Without applying an external EMF, the fluxes are maximized by short circuiting the melt with the cermet electrode. For efficient oxygen removal, the YSZ tube must be thin, contact resistances should be negligible, and the electrodes must be porous and cover the entire electrolyte surface for charge transfer. This refining process is environmentally sound, can use reducing gases such as H2, CH4 and CO without running the risk of increasing H or C content of the melt.

Jan 1, 1993

By G. Van Weert

Refractory gold ores and auriferous concentrates containing silver tend to form refractory silver jarosites during pressure oxidation. Earlier work with pure Ag2S has shown that the addition of iodine species to the autoclave feed yields cyanide soluble iodargyrite (Agl) instead. Near complete silver extractions from the autoclave product were obtained at a I-/Ag+ ratio of 5 or more. This paper reports on the pressure oxidation and cyanide leaching of two industrial refractory (arseno) pyritic silver-bearing concentrates: 1. from Peru (sulphosalts) and 2. from the USA (pyrite, with acanthite occlusions). While using a I-/Ag+ mol ratio of only 1 in the feed, it has been possible to obtain 98 and 97% Ag extraction from the two autoclave products by cyanide leaching, respectively. This compares to 11 and 54% Ag extraction from the as-received concentrates and 4 and 15% Ag extraction, respectively, after pressure oxidation without KI present. The results of the testwork are discussed in terms of concentrate mineralogy and pressure oxidation conditions.

Jan 1, 1994

By Mark Tjerkstra

In ,1993, the WMC Resources Ltd.-owned Kalgoorlie Nickel Smelter, underwent a capacity upgrade. This capacity increase was offset by .air quality control restrictions limiting the smelter's availability to 80%. As the direct. result of this limitation, WMC Resources Ltd commissioned a double absorption contact ,acid ,plant for the desulphurisation of furnace waste gas in August 1996. The history and the impact of the acid plant on S02 emissions and air quality is reviewed. General descriptions of the other aspects of the Kalgoorlie Nickel Smelter's Environmental Project are also included in the paper. Information on 'the design features? and operating practices that relate to or contrast with practices at operations visited by KNS personnel prior to acid plant commissioning provide the paper's focus. Smelter operation has changed markedly from unstable operation prior to 1997 to continuous" operation with little down time due to mechanical or process failures resulting in increased smelter availability to more than 90%

Jan 1, 1998

By Mark Jolly

"Instead of using the traditional batch casting process, the CRIMSON [1] (Constrained Rapid Induction Melting Single Shot Up-Casting) method employs a high-powered furnace to melt just enough metal to fill a single mould in a closed crucible. The crucible is transferred to a station for computer-controlled counter gravity filling of the mould for optimum filling and solidification. The CRIMSON method therefore holds the liquid aluminium for a minimum of time drastically reducing the energy losses attributed to holding the metal at temperature. With the rapid melting times achieved, of the order of minutes, there isn’t a long time at temperature for hydrogen to be absorbed or for thick layers of oxide to form. The metal is never allowed to fall under gravity and therefore any oxide formed is not entrained within the liquid. Thus higher quality castings are produced leading to a reduction in scrap rate and reduced overall energy losses.IntroductionEngineers at the University of Birmingham, England, with local company, NTec, have invented a new casting process that will reduce the energy costs of light-metal foundries. The technology, entitled CRIMSON, means that foundries need only heat the quantity of metal required to fill a single mould rather than large batches that use unnecessary energy and create waste. The complete concept of CRIMSON requires a change of philosophy in the approach to casting and requires the user to think holistically in order to reap the full benefits from the process. This paper will discuss the various aspects of energy wastage within the foundry sector and discusses the processes whereby the energy can be reduced. Primarily the author focuses on the aluminium sector but CRIMSON can be applied to many of the non-ferrous “light” alloys. Ferrous materials and non-ferrous “heavy” alloys can also benefit from some of the ideas but not necessarily directly from the application of CRIMSON."

Jan 1, 2010

By D. L. Jones

The leaching of natural chalcopyrite was studied in both ferric sulfate and ferric chloride solutions. The chemistry of the two reactions is quite different, with substantial sulfur oxidation occurring only in sulfate solutions. Ferric chloride is a more effective reagent, for the leaching rate is greatly increased with finer particles and higher (Fe+++), and unaffected by high (Fe++); none of these advantages are found with ferric sulfate. In addition, the morphology of leaching appears to be different, with ferric sulfate leaching preferentially along fissures or grain boundaries. The kinetics were found to be linear over an extended period, rather than parabolic as reported elsewhere. An explanation of the observed phenanena is proposed using the electrochemical theory of leaching, and experimental measurement of the mixed potential of the mineral during leaching.

Jan 1, 1976

By Rolando Campos

Until 1970, the Caletones Smelter of CODELCO-CHILE, División El Teniente, operated under the conventional pyrometallurgical process used by most of copper smelters. The annual copper production varied around 165.000 tons. The failure in the commissioning of the "oxygen smelting" technology in Peirce- Smith converters (1970-1972), forced further introduction of transcendental changes in the Caletones smelter operating scheme. Implemented technological innovations were based on wide studies and research works performed by División El Teniente. This paper presents a summary of technological modifications introduced, their impact on production and energetic performances, and short and medium terms improvement plans.

Jan 1, 1993

By Zhijing Zhang

A thermodynamic structure model for alkali borate melts is developed to describe the distribution of structural groups in the alkali borate melts as a function of compositions. Fractions of threefold coordinated boron atoms and fourfold coordinated boron atoms in the potassium borate melt are calculated for the entire composition range and compared with results reported in the literature. The model has been used for structural interpretation for the borate anomaly in viscosity, which regards the borate anomaly as a manifestation of the various antithetical effects caused by the introduction of alkali oxide into boric oxide. It has been found that the viscosities of alkali borate melts increase or decrease according to the changes in rigidity and spatial connectivity of the glass network structure, which is a function of temperature and composition.

Jan 1, 2001

By Dolf Gielen

This paper discusses the results of a Western European energy and materials systems engineering study that analyses the impact of greenhouse gas (GHG) emission reduction on the future of the steel and aluminum industry. he technology selection will be significantly affected by future CO2 policies. The avail- ability of C02 removal and storage technology and the social acceptance of this strategy for GHG emission reduction is of key importance for the strategy selection. The use of coal based smelting reduction technologies is optimal in case of weak C02 policies or in case of strong C02 policies and low CO2 removal and storage costs. The selection of CCF or Corex technology depends on the penalty regime. However, if C02 removal proves to be problematic, CCF development fails and strong C02 policies are introduced, the gas based DRI production processes will become more attractive. In both cases, the energy efficiency of the iron and steel industry will further increase in the next decades. The impact of GHG emission reduction on aluminum prices and aluminum use can be significant. However contrary to common notions the aluminum production will be positively affected by GHG emission reduction, notwithstanding the currently high emissions in aluminum production. A combination of emission mitigation in production and significant GHG emission reduction effects further down the product chain cause this effect. A significant potential exists for improved materials efficiency. This potential is generally neglected in energy efficiency and CO2 reduction studies. However improved steel qualities are of similar importance for C02 emission reduction as increased energy efficiency. It remains to see if this potential will be used to its full extent in the next decades. Model calculations indicate that the impact of C02 policies on the competition with other materials will be limited. Greenhouse gas emission mitigation will have much more impact on materials production and waste handling than on materials consumption.

Jan 1, 1999

By Andreas Nolte

This paper includes a comprehensive report about the metallurgical utilisation of reusable products from electronic scrap recycling, car shredding industry, used glasses an various waste products, such as slimes and flue dusts, generated in a secondary copper smelter. Depending on the copper content, the type of copper compounds and the characteristics of accompanying substances, the materials are treated by smelting in furnaces, operating under reducing or oxidizing conditions. HKs pyro- and hydrometallurgical processes, blast furnaces, converters anode furnaces, tin lead alloy plant and tankhouse will be outlined. The reusable products are categorized according to the origin of the materials and then presented in the form of quantity and quality balances. Processing methods, process able quantities and quality requirements of inputs are described. The utilization degree of the most important metals (copper, tin, lead and zinc) is described with graphics. The report is rounded by information on operating licence according to the environmental regulations of the Federal Republic of Germany and data concerning supply and contracts

Jan 1, 1997

By F. D. S. Marquis

An investigation of the mechanisms of formation of two types of porosity-primary and secondary-their characterization, evolution during processing, and effects on the mechanical behavior (fracture, fatigue, and failure) of 7X50 and 2X24 alloys has been conducted. The mechanisms of formation of three forms of primary or cast porosity were investigated, and each form was characterized: (a) macroscopic shrinkage porosity-MSP); (b) microscopic interdendritic porosity (MIP); and (c) hydrogen gas porosity (HGP) or primary hydrogen porosity (PHP). The mechanisms of formation of four forms of secondary or thermal/thermomechanical porosity were investigated, and each form of porosity was characterized: (a) high temperature oxidation (HTO). internal hydrogen precipitation (IHP), or secondary hydrogen precipitation (SHP); (b) preheating blistering porosity (PBP); (c) eutectic melting porosity (EMP);and, (d) dissolution micro void formation (DMF). The evolution and interactions of the primary and secondary types of porosity (w.ith special emphasis on PHP and SHP) during industrial and laboratory processing and their effects on the fracture and failure behavior of both types of alloys (with special focus on fatigue crack initiation and propagation) were investigated.

Jan 1, 1996

By S. G. Kumar

The performance of nickel based high temperature materials is directly related to their microstructure, which is controlled by the various processing steps. Nickel base alloys are melted and refined by a variety of processes that include Vacuum Induction Melting (VIM), Vacuum Arc Remelting (VAR) and Electroslag Remelting (ESR). The limitation of VIM is that the metallrefractory reactions lead to the disintegration of the crucible and hence contamination of the product due to macrosegregation. This macrosegregation is alleviated to some extent by controlling the solidification in VAR. The main attraction of ESR is its ability to produce a clean product by controlling the deleterious inclusions. In recent years Electron Beam Melting (EBM) is emerging as an alternative to the VIM, VAR and ESR. This paper reviews the current status of these processes and outlines the scope for further improvements in the processing technology.

Jan 1, 1993