Search Documents

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Furnace refractories are in most cases chemically incompatible with smelter slag, which leads to a steady erosion in their thickness over time. Once too thin, refractory walls become mechanically unstable and catastrophic failure can result. Historically, external shell cooling was applied to generate a freeze lining of slag and thus prevent refractory erosion. Many modern high intensity smelting furnaces instead maintain their physical integrity by the use of internally cooled wall panels, plates or finger coolers. An initial refractory lining is often installed inside of the coolers, such that the furnace originally operates with a temperature (insulated) rather than a heat flux (freeze lined) boundary condition. This paper examines the change in slag-wall heat transfer coefficient and slag superheat as a function of process intensity. The implications of the changes in heat transfer on residual brick thickness are explored using analytical modelling.

Jan 1, 2016

By C. Acuna

The standard procedure of fire refining consists of sulphur removal via air injected through tuyeres, arsenic slagging via soda-lime flux and oxygen reduction by air or oxygen deficient air or a steam fuel mixtures. The use of porous plugs to stir with an inert gas has been mainly considered as a surface renewing agent that increases the product quality and shorten the refining cycle. In the present study the effect of the bottom stirring by nitrogen gas injection through porous plugs for the treatment of the crude copper in the range of 400-150 ppm sulphur, 3,000?2,000 ppm arsenic and 14,000-7,000 ppm oxygen content was investigated. The combined effect stirring-reducing, by the use of air or a steam fuel mixtures through tuyeres for oxygen removal, follows a kinetics of first order where the constant, K, can be represented by the following polynomial expression: K = A .* R2 + B * R + C Where A, Band C are constants that depend on the nitrogen flow rate and R is the air-fuel ratio or the steam-fuel used in the reducing step. Depending on the optimization of the flow of nitrogen and the air-fuel or steam-fuel mixture and only if just the oxidation, complexing and reducing steps are considered, the process cycle might be shortened by 45%.

Jan 1, 2003

By Cissé Kane, Klaus Hieronymi, Mathias Schluep, Gerry Newson, Susanne Dittke

"E-waste is currently the fastest growing waste stream in South Africa as well as in many other African countries. Informal collectors, dismantlers and recyclers based in Africa play an increasingly larger role in the processing of e-waste under generally unacceptable social and environmental conditions. In direct response to this trend, and as part of Hewlett Packard’s international Extended Producer Responsibility, the project “e-Waste Management in Africa” was started in 2007 in cooperation with the Global Digital Solidarity Fund (DSF) and the Swiss Federal Laboratories for Materials Testing and Research (Empa). This project is investigating the e-Waste situation in various African Countries, including South Africa, while actively supporting the development of practical, socially just and environmentally acceptable local e-waste management solutions. To this end, the project has been funding the development of a pilot project in Cape Town, South Africa since February 2008, supporting the start-up of a low tech/highly labour intensive material dismantling and recovery facility (MRF) for the pre-processing of e-waste. The aim is to test the feasibility of an integrated value adding local e-Waste management system, designed to maximize the potential of refurbishment, repair, re-use, dismantling and recycling of equipment, with environmentally responsible disposal as a last resort only. The project also seeks to incorporate the current informal e-waste processing activities, by transforming them into sustainable and environmentally sound operations. The MRF acts as a nucleus, raising awareness, and providing training and education to previously disadvantaged individuals as a means of creating opportunities for entrepreneurship in the technical maintenance, dismantling and waste-to-art project sectors."

Jan 1, 2008

By E. T. de Groot, D. L. Verhelst

With the successful start-up of Cominco's new KIVCET smelter, the final key component is now in place for Trail Operations to operate efficiently as a modern integrated zinc-lead facility. Unique metallurgical, operational, planning and management issues apply to this operation. Along with presenting the current flowsheet for Trail Operations, this paper discusses issues such as the impact of recycles, operational re-stabilization following significant process changes, plant operation with just-in-time inventories, real-time process optimization, and management philosophy.

Jan 1, 2000

By M. Neises, M. Roeb, C. Sattler, S. Stenger

"A two-step thermo-chemical cycle process has been developed and investigated. It is based on metal oxide redox pair systems, which can split carbon dioxide as well as water molecules by extracting oxygen atoms and reversibly incorporating them into their lattice. If concentrated solar radiation is used as the heat source, a promising method exists to produce synthesis gas from water and CO2. An easy way of operation is gained by the combination of a ceramic substrate as the absorber structure, which can be heated to high temperatures with concentrated solar radiation, and of a metal oxide coating which is capable to carry out the redox reactions. The performance and kinetics of a ferrite based redox material coated on ceramic substrates were investigated in a laboratory set-up. CO2 could be reduced with significant conversions. In addition, several side reactions were observed like the formation of carbon and like the Boudouard reaction.IntroductionThe search for alternative energy carriers and for processes able to reuse carbon dioxide stimulates the research for sustainable routes of alternative fuel production. In the scope of this search thermo-chemical processes combined with sources of concentrated solar energy have become more and more attractive. Ideally, the only raw materials for such processes are water (H2O) and carbon dioxide (CO2) enabling not only a process free of emissions, but also allow to reduce emissions of other processes by reusing CO2 to provide synthesis gas, which itself can be applied to produce chemical commodities or even better synthetic fuels like methanol or petrol.In contrast to the direct splitting of those raw materials, thermochemical cycles split water and CO2 in several steps and enable hydrogen (H2) and carbon monoxide (CO) generation at temperatures controllable by today’s technical equipment. One of the most interesting thermochemical cycles is a two-step process using metal oxide based redox systems. During the first step of this cycle (the regeneration step) the metal oxide is reduced setting some of its lattice oxygen free according to reaction (1). In the next step (the splitting) the reduced and activated material is oxidised by withdrawing oxygen from water and CO2 and at the same time hydrogen and CO is set free according to reactions (2a) and (2b) respectively."

Jan 1, 2011

By G. Glinski, K. A. Pericleous

"Recent advances in new computational modelling techniques such as Lattice-Boltzmann and Dissipative Particle methods offer the prospect of simulating complex fluids such as colloidal and dense suspensions in industrial processes. They are referred to as mesoscopic methods since they lie between molecular dynamics at a microscopic atomistic scale «lO-9m) and traditional macroscopic CFD methods (> 1O-2m). The models behave like a 'coarse-grained' gas consisting of fictitious interacting particles, which are much larger than the real molecules of the actual fluid they represent. Inter-particle forces are set so that the collisions collectively mimic the phenomenological transport properties and flow of the underlying fluid at a macroscopic scale.Much of the developmental work to date has focused on laying theoretical foundations based on thermodynamic and kinetic theory. Successful applications include predictions of macroscopic transport properties of complex fluids and flows in porous media and filters. With the constant increase in computational power, these mesoscopic methods are now sufficiently developed to determine their suitability to simulate complex fluid flows in real industrial processes. This work describes the application of meso scopic methods to the stencil printing of solder pastes in the assembly of electronic components. The aim of this work is to assess the ability of these methods to study the transport mechanisms of individual solder particles suspended in the flux solvent as they enter and fill the micro-apertures of a stencil. This paper demonstrates the coupling of such mesoscopic methods to continuum CFD methods to predict the flow of dense suspensions (i.e. solder paste) in industrial processes."

Jan 1, 2001

By Zhang Duomo

A novel homogenous precipitation method, including microwave heating, solution conductivity controlling and freeze drying, was developed for the preparation of US nanoparticles. The effects of the precipitation conditions on the structure and morphology of CdS particles were discussed individually. It was found that under the experimental conditions the particle sizes were controllable in the range of 14nm to 100nm. Blend-type CdS was obtained from nitrate or sulphate solution and the more stable wurtzite-type US was obtained from chloride solution, which was ascribed to the coordination of C1 and Cd2+ altering the supersaturation of the solution as well as the different growth units and their connecting patterns, In the precipitation process the surface of US nanoparticles were surface modified with CH3CHSCOOH. The results demonstrate that the bifunctional thiols of thioglycolic acid modified the surface through Cd-S coordination bonding and the induced counter ion AOT-SO3 as the balance charge further increased the stability and dispersity of US nanoparticles. This surface-modified US nanoparticles had been used to prepare nonlinear optics and self-assemble catalysts.

Jan 1, 2003

By Murali Thirukkonda, Rahul Shah, Srinivas Tangrila, Shankar Rachakonda, Jan Kajuch, Arthur Gurson

"High-temperature superconductors have potential for a variety of applications such as power generators, superconducting magnets for mine sweepers or ship propulsion motors, and magnetic levitation transportation systems. Interest in the use of superconducting wires and tapes increased dramatically after the discovery of high-critical-temperature (high-Tc) oxide superconducting compounds, which offer operating temperatures above that of liquid nitrogen. Several techniques have been proposed to produce commercially viable high-Tc oxide based superconducting wires. One of the promising methods involves multi-pass powder-in-tube (PIT) wire drawing followed by rolling and heat treatment. This work focuses on the development of a numerical model to simulate the PIT drawing process for fabrication of long lengths of silver sheathed Bi-2212 superconducting wires. The finite element based model was used to predict densification of the oxide powder, wire drawing forces, and silver sheath thickness during drawing. A cap-type pressure dependent constitutive equation was implemented in the model to simulate the powder behavior. The model incorporated experimentally obtained material data for the silver and powder. Results indicate that powder densification is increased by decreasing the initial silver thickness and increasing the silver strength. Data from wire drawing experiments were used to verify model predictions. IntroductionSuperconducting wires and tapes can be used to carry large dc currents with no measurable loss due to resistivity. When used in superconducting magnets for power generators, motors, levitation devices, magnetic detectors, or energy storage devices, they could potentially result in significantly reduced energy losses. In the past, most prototypes were tested in liquid helium at 4.2K [1]. However, the necessity to provide liquid-helium cooling systems proved to be a serious limitation in commercialization. In 1986 high-critical-temperature (high-Tc) oxide superconductors were discovered [2], which could allow for higher operating temperatures above liquid nitrogen (77 K). Since then, both academia and industry have concentrated their efforts on the development of high-Tc oxide superconducting wires, tapes and coils. As yet, large scale fabrication of long lengths of these wires with the required current carrying capacity and mechanical properties remains an enormous challenge."

Jan 1, 1994

By Ravi Vancheeswaran

The consolidation of ceramic fiber reinforced metal matrix composites is a key process step in the synthesis of high performance composite systems. A simulation tool has recently been developed for predicting the evolution of the composites internal state microstructural variables (eg. relative density, fiber microbendinglfracture, and chemical reaction layer thickness at the fiber-matrix interface) during the consolidation processing of spray deposited composite mono-tapes. A Generalized Predictive Control (GPC) scheme is used in conjunction with the simula-tion tool to design near optimal process paths that minimize fiber damage and reaction product thickness while simultaneously maximizing the composites relative density. The microstruc-tural evolution depends nonlinearly on the process conditions and therefore the scheme uses a constantly updated linearization of the model to optimize the input process variable vector. A control simulation is presented to illustrate the performance of the design scheme and to assess the feasibility of its use for the achievement of goal state microstructures at the completion of consolidation cycles.

Jan 1, 1996

By Joël P. T. Kapusta, Romeo U. Pagador, Noparut Wachgama, Chumnoom Khuankla

"Thai Copper Industries (TCI) is a custom copper smelter and refinery in Rayong, Thailand, with an annual capacity of 165,000 tons of cathodes. It employs the El Teniente Technology as the primary smelting reactor to produce white metal from copper concentrates. The white metal is further treated in Hoboken Siphon Converters to produce blister copper then refined in anode furnaces before being cast into anodes for electro-refining in the on-site tankhouse.Thai Copper Industries is the first copper smelter to install and successfully operate on a commercial scale with the Air Liquide Shrouded Injection (ALSI™) Technology in the Hokoben converters with sonic injection of oxygen enriched air and nitrogen for cooling of the injector tip areas. Following commissioning and the establishment of operating practices, the performance of the Hoboken converters with ALSI™ Technology produced outstanding results. The unique combination of an El Teniente and Hoboken siphon converters, both of which are bath smelting operations, offers very high blowing and oxygen efficiencies. As a consequence, reverts recycling was accelerated with minimal build up on the mouth, end-plates or even below the siphon that is typical in Hoboken converters.These outstanding results in the Hoboken Siphon Converters with ALSI™ Technology helped the TCI Plant reach a production of about 75% of its capacity within four months despite the fact that the TCI staff is quite young and its converter know-how and experience are not yet fully developed."

Jan 1, 2009

By D. Doungdeethaveeratana

The extraction kinetics in a novel solvent extraction process have been investigated. In this process, the liquid-liquid emulsion is generated by bottom gas injection into countercurrently flowing aqueous and organic phases. This process has a number of advantages over the mixer-settler unit or the spray column in terms of simple equipment configuration, without any mechanical moving parts, and the ease of cleaning and process control, while providing a sufficiently large interfacial area for rapid mass transfer. The overall rate increased with increasing gas injection rate and height of the aqueous phase but decreased with increasing injector diameter at the same gas injection rate. The variation of the overall rate constant was correlated against a set of dimensionless numbers, representing the operating conditions. Extraction rates and efficiencies comparable to those in a mechanically generated emulsion were attained in this new process.

Jan 1, 1998

By Akira Yazawa

Experimental results for the distribution ratios of various elements between the slag, matte and/or copper in the silica-saturated copper smelting system were summarized. The experiments were carried out under an oxidative smelting condition with S02 gas flow, and also a reductive smelting condition equilibrating with metallic copper or iron. To evaluate the results thermodynamically, the availability of one atom cation base expression for the constituent compounds is emphasized from both of theoretical and practical standpoints. Both of oxidic and sulfidic dissolutions in slag are postulated for some elements such as copper, nickel and lead., and the experimental results are reasonably explained thermo-dynamically. The results for the mutual solubility between matte and ferrite slag and the distribution of minor elements between liquid copper and ferrite slag are also discussed.

Jan 1, 1983

By R. E. Brewer

Pilot scale flotation tests were conducted with a l?ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pet of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated. The tailings were first water leached at approximately 60? C, and the water-leached tailings, containing approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH' and sodium sulfide addition on gold flotation recovery and redox potentials were examined. Maximum gold flotation recovery, 36 pct, was achieved at pH 8,5 with a sodium sulfide addition of 0.18 Ib/st. Overall gold recovery by leaching and flotation was in the range of 70 to 80 pet.

Jan 1, 1989

By Walter Curlook

An atmospheric acid leaching process for leaching nickel and cobalt from highly-serpentinized saprolitic fractions of nickel laterite deposits has been developed and patented [I]. The process involves leaching the highly-serpentinized saprolitic portion of the nickel laterite ore profile in strong sulphuric acid solutions at atmospheric pressure and temperatures between 80°C and 100°C, essentially autogenously, to extract over 85% of its contained nickel content and a large proportion of its cobalt content after leaching times of about one hour. The amount of sulphuric acid used in the leaching process is between 80% and 100% by weight of the finely ground highly-serpentinized saprolite ore on a dry weight basis. The metal values are recovered as intermediate products. Key words: Atmospheric Leaching; Nickel Oxide Ores; Laterites

Jan 1, 2004

By L. A. Bertram, F. J. Zanner

"The goal of this paper is to present a tool to simulate transient melting of the electrode tip. This capability is needed to develop and test furnace control algorithms since experimental determination is difficult and expensive. Simulation incorporates parameters (including arc voltage, arc current, electrode gap and furnace pressure) from previous quasi steady experiments with 460 mm diameter Inconel 718 electrodes.Cathode heating rates (determined by classical as well as experimental arc models) are linked to these independent variables. After radiative loss adjustments to the heating, transient one dimensional melting is computed. IntroductionThe vacuum arc remelting (VAR) process attempts to improve the physical and chemical homogeneity of a static-cast electrode by remelting and solidification in a quasisteady manner. To achieve steadiness of furnace operation requires automatic controls based on inputs measuring physically relevant state variables of the process. Previous industrial scale VAR studies (1,2,3) involving stainless steels, superalloys, and other alloys have provided a basis on which control strategies of some generality can be proposed (4). Of these measurements, the data for Inconel 718 is the most complete, so discussion in this paper is restricted to this alloy.Studies of the In 718 alloy subjected to the VAR process have established that melt rate M (kg/hr) depends not only on the melt current 1m (kA) supplied to the furnace, but also on ambient gas pressure of CO, PCO (micron), and electrode gap ge (mm) as well (1):"

Jan 1, 1986

By A. Mezei

A process has been developed to recover cobalt, gold and bismuth from the NICO deposit in Canada. The process consists of a bulk rougher flotation followed by an optional separation by flotation to produce a bismuth concentrate and a cobalt concentrate, grading on average 12.8 % Bi and 1.8% Co, respectively. Cobalt is leached by pressure oxidation at 97% efficiency, producing a pregnant solution suitable for further processing. Before optimization, about 38% of the bismuth is recovered in the selective concentrate, wherefrom it is recovered by ferric chloride leaching followed by cementation, at overall efficiencies exceeding 98%. The gold is recovered from the cobalt and bismuth leach residues by cyanidation, at 95% efficiency. Previous work described the results of the leaching of the concentrates, recovery of gold (Part I) and the recovery of bismuth (Part 11). This work describes the results of the cobalt recovery testwork and the resulting conceptual flowsheet. The sulfur dioxide-oxygen system was the most efficient for the oxidationlprecipitation of iron and arsenic from cobalt bearing pregnant leach solutions, producing purified solutions assaying <1 mg/L As and <8 mg/L Fe. The efficiency of cobalt solvent extraction (from the resulting purified PLS containing about 1 g/L Co) ranged from 9 1 to 98%; the co-extractions ranged from 88 to 100% for copper, from 28 to 33% for magnesium, from 6 to 7% for calcium and from 96 to 98% for zinc. Sulphide precipitation processes (using either sulfur dioxidelelemental sulfur or sodium sulfide) produced residual copper concentrations in the cobalt strip solution ranging from 0.1 to 2 mg/L Cu. About 90% of the calcium and magnesium were separated by scrubbing the organic with cobalt sulfate, producing residual concentrations of 12 mg/L Ca and from 180 to 330 mg/L Mg in typical feed solutions directed to cobalt carbonate precipitation tests. Cobalt carbonate precipitation efficiencies ranged from 75 to 78% when calcium and magnesium co- precipitations were restricted from 8 to 17% and 0.3 to 0.4%, respectively. The limits required by most stringent specifications on commercial grade cobalt carbonate products were met or exceeded.

Jan 1, 2002

By A. M. Strachan

Capper Pass & Son Limited Was, until its recent closure, the world&apos;s largest producer of tin from secondary materials including solder drosses, non-ferrous smelter flue dusts, tin based metal alloys, residues and slags. Polonium-210, an alpha emitting radionuclide, was present in varying concentrations in some of the numerous feed materials processed by the smelter and refiner. The polonium-210 followed a complex path through the process flowsheet. This paper discusses the behaviour of polonium, both from its arisings in other smelters&apos; process streams and through the entire Capper Pass smelting and refining circuit. The consequential personnel safety and environmental precautions necessarily taken in some areas of the process operation are outlined.

Jan 1, 1992

By K. D. Mondale

The chemical and physical properties of samples from ten sedimentary zeolite deposits. (representing chabazite, clinoptilolite, erionite and mordenite types), have been determined as a prelude to the development of a wet beneficiation process. The mineralogical composition of each deposit and such properties as morphology, size, apparent density, surface area, pore volume, relative hardness and zeta potential in solution have been determined. Some of these properties, especially apparent density and relative hardness, were found to differ significantly from textbook values. Based on differences in properties between the zeolites and their associated gangue minerals, a wet beneficiation process has been developed which makes use of selective grinding, sizing, sorting and gravity concentration. Additionally, an alternative upgrading process using flotation has been developed for one of the deposits.

Jan 1, 1988

By S. q. Honingh, G. Van Weert

Currently produced zinc-enriched blast furnace dust is stored on site at CORUS IJmuiden. To end this practise, a research program was started in 1996. Four technologies were studied: oxidative autoclave leaching in a chloride medium, fluid bed pyrohydrochloridisation (pyrohydrolysis) to yield lead-zinc-free (hematite) calcine, EAF (plasma) smelting/zinc fuming, and incorporation of the dust in 'iron foundry cupola charges. All aim to remove zinc and lead, recycle the iron residue internally, and produce a saleable zinc-lead product.

Jan 1, 2000

By A. René Silva

The separation of Fe(III) from simulated Ni(II) solutions using different ion exchange resins was studied. The resins tested included cation exchangers with sulfonic and carboxylic groups and chelating resins with iminodiacetic, aminophosphonic, and mixed sulfonic and phosphonic groups. The dosage of resins was varied from 0.1 to 0.5 g/mL to study the impact of resin type and dosage on iron separation from simulated nickel leach solution containing 25 g/L Ni(II) and 25 g/L Fe(III) at pH 1.5. Also, the effects of different metal ion concentrations, Fe (III):Ni(II) ratios in solution, pH, and adsorption times were investigated. Experimental results demonstrate that all the chelating resins selected favored the adsorption of Fe(III) over Ni(II) with high Fe(III) loading. Soft cation exchange resins also favored the adsorption of Fe(III) over Ni(II), but no significant Fe(III) loading was observed. In contrast, strong cation exchange resins did not show adsorption preferences. The most efficient separation was observed using resin with aminophosphonic groups at resin dosage of 0.2 g/mL, having a Fe(III) adsorption over 94% and Ni(II) adsorption below 5%.