Search Documents

By Oscar Perales Perez, Atsuo Kasuya, Kazuyuki Tohji, Yoshiaki Umetsu

"The removal of iron and various heavy-metal ions by their incorporation into stable ferrite-type precipitates at 25°C is a promising alternative to clean up large volumes of polluted aqueous effluents. Our research work investigated the conditions to produce magnetite and various M-bearing ferrites (where M: Zn, Cu, Co, Ni, Cd, etc.) directly from aqueous solutions at 25°C by simultaneous control of the oxidizing conditions and pH. The formation of the solids was followed by monit9ring the oxidation-reduction potential (ORP) and rate of proton release during the aerial oxidation of the suspensions at constant pH (contact stage). Only mildly oxidizing conditions, represented by ORP values between -110 mV and -150 mV and a moderate oxidation rate of Fe(II) species were conducive to well-crystallized ferrites at ambient temperature.' It was also found that increasing the Fe/M mole ratio in starting· solutions enhanced the stability ·of the M-bearing ferrites at ambient temperature. When the formation of the ferrite was incomplete, aging of the sludges in their mother liquors at 25°C promoted the crystallinity of the precipitates. The mentioned conditions ·favored the suitable progress of the ferrite-forming reaction involving the oxidation of Fe(II) entities, subsequent hydrolysis of produced Fe(III) species and dehydration of the intermediate:· Furthermore,· the ferrite formation at· low temperature permits the elimination of iron and co-existing heavy metal ions to sufficiently low concentration.In tum, the characterization of the precipitates evidenced their magnetic nature (room-temperature saturation magnetization above 60 emu/g) as well as the effective incorporation of target metal ions into the ferrite structure."

Jan 1, 2000

By Ivan Imris

The iron production has generated many tonnes of very fine residues with high concentration of iron. In addition, during the recycling of galvanised steel scrap in the steel making processes the zinc and lead are largely concentrated in the dust. These kinds of dusts are usually dumped beside the metallurgical plants and cause environmental problems. Therefore the metal recovery from the metallurgical residues has become a major interest not only from the viewpoint of metals recycling but mainly from the viewpoint of environmental land protection. The thermodynamic analyses and laboratory experiments suggested that the metals could be recovered from metallurgical wastes by reduction roasting and by plasma smelting processes. The iron rich pellets with very high metallization may be obtained from metallurgical wastes by the reduction roasting and the inert slag and pig iron could be produced by plasma smelting processes. In both cases the iron rich products are suitable for the steel production. During the reduction roasting or plasma smelting the high volatile zinc and lead metals were removed and enriched as a secondary dust, Zn-Pb concentrate, which is suitable for processing in zinc and lead smelters. Suggested processes are commercially feasible and environmentally friendly without any solid or liquid waste.

Jan 1, 2003

By Du Sichen, S. Seetharaman, J. A. Bustnes

"The present study deals with the kinetic studies of reduction of some selected transition metal tungstates with hydrogen. The measurements were carried out by the isothermal thermogravimetric method. Shallow powder beds were employed in order to avoid the effects due to transport phenomena affecting the reaction rate. In this way, the chemical reaction rates could be selectively studied. The experiments were carried out in the temperature range 873 - 1173 K. From the experimental data, the activation energies were evaluated and were found to be around 88 kJ / mol in the case of both iron as well as cobalt tungstates indicating the similarities in W-O bonds in both cases. The activation energies obtained are discussed in the light of the position of the transition metal in the periodic table as well as the thermodynamic stabilities of the various tungstates.IntroductionThe tungsten containing hard metals, characterized by high density, belong to a class of two-phase metal matrix composites. While these types of materials have traditionally found their applications within the defence industry as armour-piercing projectiles, counterbalance in helicopters and military aircrafts, outer casings of hand-grenades, etc., commercial applications for this class of alloys also exist, including radiation shields, penetrators for the oil industry, turbines for turbo-jet engines and a wide range of sports related parts. A possible route to the production of these alloys is to reduce the tungstates such as FeW04, Co W04 and NiW04 using a reductant like hydrogen or carbon monoxide. In order to have a better understanding of the processes involved in the production, it is important to have a knowledge of the reduction kinetics for these tungstates. According to the knowledge of the present authors, while the reduction ofNiW04 by hydrogen gas has been investigated earlier in the present laboratorypl no systematic reduction study has been carried out previously for the tungstates of iron, cobalt."

Jan 1, 1996

By Yuri Gelfgat

"The report presents the results of theoretical and experimental investigations of the MHD method used for production of composite materials from immiscible melts, e.g., Al-Pb, Zn-Pb, Bi-Ga and others, which, when solidified, can be presumed as ""frozen emulsions""IntroductionThe searching of the methods for controlling the phase distribution in various liquid heterogeneous media is one of urgent tasks in modem material science. The studies [1-3] have revealed that in case of electrically conducting media the influence of electromagnetic body forces on the liquid can be a rather effective mean of such a control. The current paper investigates some physical conformities governing the behaviour of binary liquid metal systems with a immiscibility region under electromagnetic processing designated to produce ingots with homogeneous structure.The main idea of the proposed method rests upon a concept that the electromagnetic forces in the melt are similar to gravity forces due to buoyancy effects in space and have a selective ability to influence the melt components dependent on their conductivity. In crossed electric E and magnetic B fields (fig.I) each component of the medium is influence by the force density f = jXB, where the current density j is determined by the conductivity a of the component j = -oE. When this force is directed parallel or non-parallel to the gravity vector, the buoyancy of suspended particles can be controlled accordingly.This phenomenon allows one to create a situation in binary system, when the sums of all mass forces (gravity and electromagnetic) affecting every component are equal, and two components are under conditions of equilibrium with respect to each other. These conditions are called quasiweightlessness, which is generated in the melt by the electromagnetic forces."

Jan 1, 1998

By Hideo Nakae, Hideki Yamaura, Toshiaki Kimura

"In 1968 J. N. Reding et al. suggested processes for fabricating composites. According to their patent, decompression atmosphere, which occurs during the reaction between magnesium and oxygen and/or nitrogen in the closed system, causes the spontaneous infiltration of melt into narrow spaces such as ceramic preforms. However, they did not report the proof of this phenomenon or the industrial manufacturing method. Therefore, this research measured the pressure change among SiC particles surrounding molten aluminum. As a result, the pressure reduction during the Mg reaction was identified. Moreover, the existence of Mg3N2, which improves the wettability between Al alloy melt and SiC particles on the interface, was observed on the surface of particles. Applying these two phenomena, a new process for the manufacturing of cast discontinuously reinforced aluminum composites (DRA) was developed. This new method is expected to produce DRA without additional pressure.IntroductionWith the increasing demands for light-weight materials in the automotive and aerospace industry in recent years, ceramic particulate reinforced aluminum matrix composites called DRA (Discontinuously Reinforced Aluminum Composite) have been receiving significant attention because of its lightness, superior abrasion resistance, high heat conductivity and low thermal expansion [1-3]. Consequently, DRA was considered for electronic parts such as heat-sinks or a base for power semiconductors, and began to be applied for automotive parts including brake drums, discs, cylinder liners, pistons and so on [4- 6]. However, high machining cost is one of the significant barriers to widespread use ofDRA. One solution to this problem is the adoption of cast DRA that can be produce to near-net shape, reducing machining cost."

Jan 1, 2000

By Osamu Takai, Yoshiki Sato, Nobuhiro Tajima, Hiroyuki Sugimura

"Amorphous carbon thin films doped with nitrogen ( a-C:N) have been synthesized by means of shielded arc ion plating (SAIP). Their electron field emission properties, that is, threshold field strengths for electron emission and maximum emission current densities, were evaluated and compared with those of pure amorphous carbon (a-C) films prepared by the same SAIP apparatus. Among all of the fabricated a-C:N films, the a-C:N films with a N concentration of 23 %, which prepared using Nz arc plasm at a pressure of 1 Pa with applying a sample bias voltage of -100 V, showed the lowest threshold filed of 13.4 V/µm and the highest emission current density of 1.87 µAfcm2 at a field of20 V/µm. These field emission properties of the a-C:N film were much better than those of the a-C films. The best results obtained on the a-C film in this study were the lowest threshold filed of 15.5 V/µm and the highest emission current density of 0.052 µA/cm2 at a field of 20 V /µm. Nitrogen doping to aC was found to be effective for lowering threshold voltage for field emission and for increasing emission current density. The electron field emission characteristics of the a-C:N films depended not only on N concentration but also on chemical bonding state of nitrogen in the a-C:N films. The presence of the ~-C3N4-like phase, which contributes to improve wear resistance of a-C:N as well, distinguished by the NlsXPS peak at 400.5 eV is proved to be crucial in order to enhance field emission properties of a-C:N.IntroductionThere has been much interest in electron field emission from a cold cathode due to its potential applications in vacuum microelectronic devices including field emission displays which are expected as flat panel displays in next generation [l]. It is well known that efficient emission can be rather readily realized using tip-like shape cathodes, e.g., microfabricated three-dimensional electrodes [2], carbon nanotubes [3-5], etc. However, electron emission from planar surfaces is of particular importance since such a type of cathode is· simply fabricated and assembled into microelectronic circuits. Currently, amorphous carbon thin films doped with nitrogen (a-C:N) prepared by plasma processes have attracted attention because their threshold voltages of field emission are relatively low [6]. Among various methods for preparing a-C:N films, the process using arc plasma is of special interest since, in arc plasma, nitrogen is highly activated and new types of carbon nitride phase are expected to be synthesized. However, field emission properties of a-C:N prepared by arc plasma have been studied in less detail compared with that prepared by the other methods such as sputtering."

Jan 1, 2000

By Gong-yi Guo, Yu-li Chen

"A partially-stabilized zirconia powder was prepared by metalorganic precipitation process from technical-grade zirconium oxychloride and the effluent of an acrylic acid plant. The effluent contained low molecular weight carboxylic acids, i. e., acrylic acid and acetic acid. The· developed process is based on the selective precipitation of acrylic acid at suitable pH values by the addition of zirconium oxychloride to the effluent. The resulting precipitate is a precursor that can yield a pure, ultrafine, and partially-stabilized zirconia powder. The evolution of formation of the partially-stabilized zirconia in the present process was investigated using thermal analysis, infrared spectroscopy, and X-ray diffraction technique. Environmental, technological and cost advantages will make the present process feasible for manufacturing advanced zirconia ceramics.IntroductionIn recent years the superior mechanical, thermal, electrical and chemical properties of stabilized zirconia have become the focus of growing scientific and technological interest, and hence resulted in various structural and functional applications. The great potential of the material has given rise to numerous preparation approaches to obtain the material with the excellent properties; nevertheless, an extensive number of programmes are underway worldwide aimed at understanding and improving both the preparation and behavior of stabilized zirconia ultrafine powders. (1 – 8)."

Jan 1, 2000

By Sylwia Zymankowska-Kumon, Rafal Danko, Mariusz Holtzer, Artur Bobrowski, Michal Kubecki

"Moulding sands with furan resin constitute constantly growing part in technologies of producing castings from iron alloys. Due to the presence of harmful substances in resins such as furfuryl alcohol, phenol and formaldehyde, using those mould sands may be hazardous to the natural environment and workers. The general assessment of harmfulness of sands used for molds and cores encompasses 2 basic points: emission of hazardous substances during processes of preparing sands, pouring mold with liquid metals (high temperatures), cooling and shaking-out; possibility of washing out hazardous substances from used sands to the environment, during storage or economic use outside foundries. We present the results of research on the assessment of harmfulness of mould sands with furan resin in the scope of the above points. The research was conducted according to the original method prepared by the authors, which has been used for years in cooperation with various foundries (Poland, abroad).IntroductionSands are used by the foundry industry to create metalcasting moulds, where the individual sand grains are typically bound using bentonite clay and carbonaceous additives or resins. During the casting process, the moulds can be exposed to temperatures as high as 1500°C depending upon the metal being poured. The molten metal causes thermal decomposition of carbonaceous additives or resins, which results in the formation of potentially hazardous organics that are emitted to the atmosphere and condense in the moulding sand [1]. The moulding sands are reclaimed within the foundry, but part of them are eventually discarded in landfills, because it is not longer suitable to make metalcasting molds [2, 3]."

Jan 1, 2013

By Antti Roine

HSC Chemistry is a widely-used therniochemical tool in the chemical and metallurgical industries and in universities. The main reasons for it's popularity is the easy user interface and the large integrated thermochemical database. This paper summarizes the main properties of the new HSC Chemistry version 3.0, and gives a short review of the new features: Some metallurgical applications with the new features are also presented. HSC Chemistry 3:0 contains seven calculation modules and a thermochemical database with more than 11 ,000 chemical compounds. The new spreadsheet type table editor gives more control to the user, the new graphics routines have fewer limitations and more formatting properties. The capability and speed of calculation routines have also been improved.

Jan 1, 1998

By Rolando Campos

In August 1993, the operation of Refimet Chile's copper custom smelter commenced at La Negra, near Antofagasta in northern Chile. Design smelter throughput corresponded to 235 000 tonnes of concentrate, calcines and copper cements arising from suppliers in the north of the country to produce 90 000 t/y of blister copper. Refimet had initially gained experienced in building and operating leaching, roasting and a blast furnace facility at Rungue, near Santiago, followed by Roasting at La Negra. The initial smelter project was based on conventional reverb- smelting and Peirce-Smith converting and the majority of equipment was 'purchased second-hand and rehabilitated or modified. After only 3 years in production, the treatment capacity was significantly improved by introduction of technical improvements to the original plant operating scheme. Recently, the plant was further expanded to an annual smelting capacity in excess of 400 000 t/y feed, corresponding to around 160 000 t/y copper production. This expansion, referred to as Phase 2, was achieved by modification of the reverb to oxy-fuel firing, addition of a further (second-hand) acid plant, fire refining and anode casting facilities. Parallel development of concentrate injection into enlarged converters-also took place. Following successful commissioning of Phase 2 expansion, initial engineering studies for a third expansion phase have been completed. This aims to use leading technology based on bath smelting of bone-dry concentrates in a Continuous Reactor. This paper provides an overview of the relatively short plant history, its development and improvements together with operating indices achieved.

Jan 1, 1998

By J. D. Ecuyer, L&apos

he microstructure of galvanneal coatings formed on extra low carbon and interstitial free steel substrates has been characterized using electron microscopy (TEM and SEM) and x-ray diffraction. The coatings are found to consist of a mixture of gamma, delta and zeta phases, of which delta is the main constituent. The amounts of each phase influences the powdering resistance of the coating which was evaluated using reverse Olsen testing and 60" bending. For the three heat input conditions considered, IF coatings were always found to contain a significant amount of gamma and only those which retained zeta phase on the surface exhibited a satisfactory powdering resistance. In much the same way, ELC coatings with relatively thick gamma layers performed satisfactorily only when some zeta was retained. It was also found, however, that coatings with minimal zeta and gamma had an excellent powdering resistance. The latter coatings were produced under galvannealing conditions of lower relative heat input. These results indicate that in addition to the zinc bath composition, coating weight and galvanneal thermal cycle, the base steel chemistry also has an effect on the coating microstructure. Knowledge and control of all aspects of galvannealing is therefore essential to consistently produce acceptable coatings.

Jan 1, 1992

By Mikiya Tanaka, Mikio Kobayashi, Mansour A. S. A1Ghamdi, Kenji Tatsumi, Yukinori Saiki, Hirotaka Senba

"In order to recover nickel ion in a spent electroless nickel - phosphorus alloy plating bath and, at the same time, to remove impurities such as iron and zinc, the applicability of solvent extraction with LlX84I as the extractant has been investigated using actual spent solution. Although the extraction efficiency of nickel from the spent solution is considerably lower than that from the nickel sulfate-nitrate solution, nickel in the spent solution is selectively extracted with high efficiency at the pH of 6 - 7. The extracted nickel is effectively stripped by sulfuric acid at a pH of less .than· 3. On the basis of these results, a· flowsheet for recovering nickel from the spent solution is proposed Chemical equilibrium calculations of the spent solution has shown that the complex formations of nickel with anions such as lactate and phosphonate ions become predominant in the pH range between 2 and 6. This results in the depression of nickel extraction efficiency from the spent solution as compared with that from the .nickel sulfate-nitrate solution. By combining these aqueous equilibrium calculations with the· extraction model considering the extraction stoichiometry and the aggregation of the extractant in the organic phase, the extraction behavior of nickel is quantitatively predicted.IntroductionElectroless plating is indispensable for the recent advanced industries such as the electronic and mechanical industries. Electroless plating baths are repeatedly used by supplying the metal salts; however, the accumulation of the counter anions of the metal ions, the components formed by the oxidation of the reducing reagents in the plating baths, and the metal ions as impurities dissolved from the surface of the objective materials degrades the· quality of the plating. Thus, the baths are finally treated by a precipitation method to form a large amount of metal sludge, which is disposed in dumping sites. Therefore, from the standpoints of environmental protection and resource preservation, it is highly desired to establish a recycling process of the plating baths with minimum emission. Solvent extraction seems to be one of the 'suitable methods to recover metals from the spent electroless plating baths, because the concentration of the metal ion in the baths is relatively high, which is advantageous to solvent extraction as compared with the ion-exchange and adsorption methods. Some studies about the application of solvent extraction have already been carried out using simulated spe11t electroless plating baths [1-3]."

Jan 1, 2000

By G. Kugler, M. Tercelj

"The 1.2690 high alloyed tool steel is usually applied for cold working and is alloyed with carbide-forming elements Cr, V, W and Mo. It exhibits very poor hot deformability. Since there is no enough available data in literature for elucidation of this problem, hot workability and development of microstructure during hot deformation was studied. Hot compression tests were carried out in temperature range 850-1150 °C and strain rates range 0.001-6 s-1. SEM and OM were used for observation of microstructure. Results revealed very complex precipitation of carbides that depends on deformation temperature as well as on strain rate. It was found that especially at lower temperatures of hot working range the precipitation of carbides strongly depends on strain rate. Three different hot deformation behaviors’ were observed depending on temperature and strain rate range.IntroductionThe hot workability of highly alloyed high speed steels is usually described as relatively poor in comparison to other steels due to their tendency of cracking during hot working especially when inappropriate hot working conditions are applied. Alloying elements such as Cr, W, Mo and V in ledeburitic tool steels form carbides that improve hardenability, strength, hardness, wear resistance, etc., but they decrease hot workability and narrow hot working temperature range in comparison to conventional steels. The size, distribution, type and fraction of carbides, as well as the thermomechanical history of material and hot working parameters have major influence on the hot workability. The microstructure of ledeburitic tool steels during hot deformation can be characterized as a two-phase system consisting of an austenite matrix and a combination of ledeburitic carbides [1-4]. In the soft-annealed condition the total volume fraction of carbides is in the range 19-30% and in the quenched condition in the range 9-25%, depending on the chemical composition. During heating before deformation a large quantity of carbides dissolve, but non-dissolved carbides can have an extremely diverse influence on the hot workability due to variations in their composition, size, distribution, hardness and shape, and their different behavior during the deformation phase [5-7]."

Jan 1, 2011

By E. Açma

Sivas-Divrigi flotation plant has a capacity of 90,000 tpy. Beneficiation of the tailings of iron ore magnetic separator seems to be attractive, because of its Cu, Co, and Ni contents. In the experimental work, sulfidic flotation concentrate is produced from these tailings. A roasting-leaching-H2S precipitation procedure is used to treat this concentrate, containing 0.55% Cu, 0.51% Co, 0.74% Ni, and 0.027% Zn. Sulfatizing roasting is carried out in a rotary furnace at 690°C. Roasted product is leached with 10 gpl HzSOl at 70°C and 30% pulp density. For the precipitation of desired metal, H2S is bubbled through the concentrated solution of repeated leaching, under controlled temperature and pH. Final metal recoveries of 91% Cu, 91% Co, and 50% Ni, and 92% Zn are attained. Roasting gases with their 13% SO2 content are suitable for H2SO4 production and the leach residues can be integrated with the iron ore processing plant as they contain 57.4% Fe and very low non-ferrous metals.

Jan 1, 1993

By Cang Daqiang, Li Yu, Liu Xiaoming, Zong Yanbin

"Utilization of high-quality heat in melting slag is a great challenge for iron and steel industry. In the paper, a new method is put forward to concurrently utilize heat and slag by converting the melting slag directly into high valued materials, slag glass-ceramic. A glassceramic with a higher basicity of 0.7 than traditional basicity of 0.45 was prepared from steelmaking slag in order to utilize more hot melting slag. Effects of Alz03 on its crystallization processes were researched by XRF, DTA, XRD and SEM. Results show that Alz03 in glassceramic would have great effected on its property. When the Alz03 content ranges within 12%-15%, glass-ceramics with basicity of0.7 could reach the best performances. The change of dominant phase in glass ceramics from akermanite and wollastonite to akermanite and gehlenite would significantly degrade its mechanical property. An increase of Al2O3 content leads to a rise of the viscosity and crystallization activation energy of the glass, while results in increasing sintering temperature and crystallization temperature of glass, which contributed to its fully crystallization and densification process.IntroductionSteel slag is a by-product under a process of converting iron to steel at above 1600°C, and 0.1-0.15 ton molten steel slag would be discharged for producing per ton of steel in the process. The discharged steel slag at 1600°C has heat of 68 kgce/t. In 2012, China's steel output reached 716 million tons, and produces about 100 million tons of steel slag and 68,000 tee of heat in it [1,2]. But at present, utilization of both slag and its heat at 1600°C is a great challenge for iron and steel industry.Dry granulation of melting steel slag by air and then recovering the heat of the hot air are a traditional technology which have not yet been put into practice for very low heat conductivity of the slag and low efficient of heat exchange among the different processes [3,4]. Therefore, a new method for high efficient utilization of both steel slag and its high temperature sensible heat is put forward [5,6], which is on-line reducing and extracting iron from molten steel slag and then directly preparing glass-ceramic by use of the residual molten slag."

Jan 1, 2014

By Harrison Cooper, Stephen Pack

"Data from samples taken during rotary air blast and reverse circulation drilling are crucial to properly assessing economics of mineral deposits in the case of exploratory work, and are equally critical in accurately delineating ore and waste in execution of mine operation plans. Past studies of sampling procedures, comparing results of conventional splitting to more precise extraction of representative samples, illustrate the significant degree of error frequently encountered. Economic impact of error in mine blast hole sampling work can be shown to result in theoretical losses valued at millions of dollars annually in operating large scale mining projects. Results of past drill sampling studies are reviewed.Drill sampling technique can be improved by collecting coarse and fine particles together and extracting samples for assay from the complete flow of rock and dust simultaneously. This can be accomplished with a collection unit attached to the drill stem through which all except a small proportion of extreme fines are retained. The bulk mass can be static sampled as flow takes place through the collector when size reduction is not required. Alternately, collected mass with fines and coarse intermingled can be processed for increased accuracy through size reduction to obtain proportional samples."

Jan 1, 1999

By Mark Kramer

This paper is limited to treatment of bottom and fly ash waste resulting from WTE and RTE Cogeneration plants, commonly known as trash burners. The body of the paper defines waste generation and conventional treatment schemes. This paper does not identify a best treatment, however, it does offer a general perspective of the treatments to lead the reader to further investigation. Advantages and disadvantages of the ash treatments Is discussed in each treatment section.

Jan 1, 1996

By Ivan Imris

The iron production has generated many tonnes of very fine residues with high concentration of iron. In addition, during the recycling of galvanised steel scrap in the steel making processes the zinc and lead are largely concentrated in the dust. These kinds of dusts are usually dumped beside the metallurgical plants and cause environmental problems. Therefore the metal recovery from the metallurgical residues has become a major interest not only from the viewpoint of metals recycling but mainly from the viewpoint of environmental land protection. The thermodynamic analyses and laboratory experiments suggested that the metals could be recovered from metallurgical wastes by reduction roasting and by plasma smelting processes. The iron rich pellets with very high metallization may be obtained from metallurgical wastes by the reduction roasting and the inert slag and pig iron could be produced by plasma smelting processes. In both cases the iron rich products are suitable for the steel production. During the reduction roasting or plasma smelting the high volatile zinc and lead metals were removed and enriched as a secondary dust, Zn-Pb concentrate, which is suitable for processing in zinc and lead smelters. Suggested processes are commercially feasible and environmentally friendly without any solid or liquid waste.

Jan 1, 2003

By Dae Jin Ha

Sticking phenomenon occurring during hot rolling of two STS 430JlL ferritic stainless steels was analyzed by hot-rolling simulation tests. The sticking started from the initial nucleation stage in which the rolled materials were stuck onto the roll specimen surface, proceeded to the growth stage in which stuck fragments grew further, and reached the saturation stage. The modified 430JlL steel had a smaller number of sticking nucleation sites and slower growth rate than the conventional 430JlL steel because of higher high temperature hardness, thereby leading to less serious sticking. When the simulation test was conducted at 1070 °c, Cr oxides were formed on the surface of the rolled materials, and thus the sticking was drastically reduced because of the increased surface hardness of the rolled materials. In order to prevent the sticking, high-temperature properties of the rolled materials should be enhanced when rolled at 900°C or 1000 °C, and rolling conditions and alloying compositions, under which the oxide formation was promoted, were more important than high-temperature properties when rolled at higher temperatures than 1000 oC.

Jan 1, 2008

By Young-Sool Jin, Heung Nam Han, Hong Joon Kim, Jae Kon Lee

A mathematical model was developed considering non-symmetric cooling' and stress distribution in both thickness and width direction of strip on a run-out table of hot strip mill. In order to solve a transient heat transfer equation including the heat evolved from phase transformation, a finite element method coupled with thermodynamic and kinetic analyses was applied. The heat capacity of each phase and heat evolution due to phase transformation were obtained from the thermodynamic analysis of the Fe-C-Mn-Si system based on a sub lattice model. The phase transformation kinetics of the steels was derived by using an inverse additivity technique with continuous cooling experiments. Heat transfer coefficients of strips on the run-out table were, by applying an inverse method, determined from the actual mill data under various cooling conditions. As for the stress analysis, the density change of strip due to cooling and phase transformation, and the transformation superplasticity were considered. A 90nstitutive equation for the transformation superplasticity, which is related to the phase transformation kinetics and the internal stress due to the density change of strip, was applied. A finite element method was adopted to calculate the deformation behaviour of strip on a run-out table of hot strip mill. Using the models, the temperature-phase-deformation history and distribution of a strip on the run-outtable was calculated.

Jan 1, 2001