Search Documents

By Tristan H. Jones

Beginning in 1987, miniature dataloggers approved by the Mine Safety and Health Administration (MSHA) were publicly available for sale. The principal among these was the model CR21XQM, manufactured by Campbell Scientific, Inc. These dataloggers had been tested and were deemed permissible by MSHA and thus could be installed in the return air of an underground coal mine. In 1996, production of all permissible Campbell Scientific dataloggers ceased due to lack of sales. Data collection with these dataloggers has been a staple of ground control research in the United States for decades, and, without them, or a replacement, the capability to monitor ground behavior is severely impacted. Since that time, any party requiring a permissible datalogger has needed to borrow one that was purchased during the production years. In order to fill this technology gap and ensure its own data-gathering capabilities, the National Institute for Occupational Safety and Health (NIOSH) has developed and refined its own miniature data acquisition system (MIDAS). On February 16, 2010, MSHA deemed the MIDAS to be permissible and approved it for use in the return air of an underground coal mine. The MIDAS is an intrinsically safe, 16- or 24-bit datalogger, compatible with a wide range of resistive, single-ended, and differential-type instrumentation. It contains enough data storage memory to operate for over a year with typical data rates and is efficient enough to do this on a single C-sized alkaline battery for that entire period. It is menu-driven and requires no programming knowledge to operate. It supports wireless or hardwired communication for datalogger setup and data download. This paper describes the design, field and laboratory testing, and capabilities of the MIDAS datalogger. While not as fully -functioned as the CR21XQM, it is the only new permissible datalogger available, and there is intent to make it available to the mining industry for purchase.

Jan 1, 2012

By Dennis R. Dolinar

Screen material in the form of welded wire mesh and geogrids are used in underground coal mines to prevent the fall of small pieces of rock from the roof between roof bolts. Further, if the screen is installed during the production cycle, roof fall injuries can be reduced significantly. Therefore, the National Institute for Occupational Safety and Health (NIOSH), because of the safety implications, conducted an evaluation of screen materials commonly used in U.S. coal mines to determine their support characteristics and identify the parameters that could affect their performance with respect to controlling the fall of rock from the roof surface. To evaluate the load and stiffness characteristics of the screen, a test frame was designed and installed in the Mine Roof Simulator (MRS) at the NIOSH Pittsburgh Research Laboratory (PRL). With this test set up, the screen is bolted at four corners of the frame and a center load is applied. The test set up allows for up to 20 in of screen deflection while the load and screen defection are continuously recorded. A series of tests were conducted to evaluate the effects of various parameters such as bolt tension, the type of load bearing surface and the size of bearing plates on welded screen performance. The most common screen material used in U. S. coal mines is an 8-gauge wire welded in a 4-by-4-in spacing or aperture. The peak screen load was normally limited by wire breakage. The conditions at the bearing plate influence the nature of the wire breakage. However, the screen stiffness was controlled by slippage at the bearing plates, and by weld and wire failure. The size of the bearing plate had a significant effect on the performance of the welded screen. Therefore, the design capacity of the 8-gauge screen is evaluated based on plate size. For a 6-by-6-in bearing plate the average peak load is 2,900 lb with a stiffness of 250 lb/in. For an 8-by-8-in bearing plate, the average peak load is 4,500 lb with a stiffness of 430 lb/in. These test results are based on a 4-by-4-ft bolt spacing. A geogrid mesh was also tested.

Jan 1, 2006

By Srinivasulu Tadisetty

The productivity and safety of Indian longwall operations are insignificant because of complex geomechanical conditions. Therefore, the continuous monitoring and forecasting of abnormalities is imperative. Authors developed an innovative real time system and implemented in one of the Indian longwall mines. The real time system was successfully acquired data from underground chock shields and classified the behaviour in real time as per the standard norms. Furthermore, it forecasted the abnormal behaviour of chock shields promptly. The management was implemented appropriate precautionary measures based on real time forecast. Subsequently, the longwall operations were successfully completed with enhanced productivity and safety. This paper discuss the impact of the innovative system on productivity of experimental longwall mine.

Jan 1, 2006

By Bill Stormes

This paper will discuss implementation of the Hilti OneStep rock anchor technology to improve face bolting operations during the May 2008 longwall move; increase rock anchor installation capacity; and improve safety by reducing employee exposure periods by utilizing the Hilti OneStep rock anchors.

Jan 1, 2008

By W. J. Mcgaughey

A crosshole seismic imaging (tomography) experiment has been carried out in an underground mine in order to delineate waste rock within a massive sulphide ore body. Data comprising 1526 travel time measurements were inverted to yield a compressional wave speed image consistent with, and adding to, knowledge of the extent of the waste inclusions. An effective method of resolving travel time discrepancies measured on reversed ray paths is presented.

Jan 1, 1989

By Holger Witthaus

Beside the traditional geomechanical evaluation methods the geotechnical parameters are recognized as important facts of the planning work for multiple seam mining. Standards for applied monitoring and investigation methods for geotechnical determination of drill cores, laboratory rock-tests and observation of roadheadings are the basics for rock mechanics classification and support design. The geomechanical classification is in this context an essential element. The planning procedure, as it is becoming more and more detailed, beginning with the panel layout up to the technical instructions of roadway development and design of roadheading machinery, nowadays uses a lot of geotechnical information that also are expanding to include quantitative determination of more parameters. The current monitoring system includes the description of separation planes using drill cores and roadheading observation as well as laboratory tests of rock-strength and geophysical borehole examinations. This information is analyzed within the geomechanical standard-classification. The re-engineering process of comparison the predicted support success to the actual monitoring results provides the opportunity for continuous optimization of the planning work und support design. This way of empirical analysis is used for basic planning work in Germany for decades. But using the technical standard of information technology and a centralized database now it is possible to reach quick-win effects in implementing research results on the one hand and actual experiences on the other hand.

Jan 1, 2006

By Hideki Shimando

Periodic weighting and windblast which are caused by the dynamic effects of overburden in a longwall panel significantly affect longwall mining This study describes past experience with wind blast at Miike Colliery, proposes a new loosening system using hydraulic fracturing and moistening, and also discusses strength deterioration in hard-to-collapse roof rocks due to water in order to solve the problems caused by the effects of dynamic roof rocks behavior in a longwall face

Jan 1, 1998

By Dave Minney

The South African mines health and safety regulations require that mine management establish a quality management system for rock support material. Quality control of resin capsules used as a support medium in South Africa is specified under SA National Standards No 1534. Experience has shown that this specification, while addressing the chemical and physical aspects of the products, but does not address the required performance criteria. In order to address this shortcoming, the industry has put a lot of emphasis on short encapsulation pull tests, performed insitu, in the underground workings of the mine. This is also fraught with many shortcomings, particularly as regards site availability, cost and repeatability of results. To try and address these issues, the Department of Mechanical and Aeronautical Engineering at Pretoria University were approached to develop equipment and machinery that could produce reliable, repeatable results in a laboratory environment which reasonably simulates installation practice underground. The test method is based on the ASTM F432-95 Strength Index test, but modified to use push test rather than pull tests. The paper describes development of the test method and the preliminary results and findings of the work.

Jan 1, 2007

By Jun Lu

There are many factors affecting the strength of pillar, including width-to-height (W/H) ratio, mechanical properties of coal and surrounding rocks, property of partings in the coal, and the interface property between coal seam and the roof/floor. In this paper, the effect of varying pillar?s width-to-height ratio (W/H=3, 5, 7, and 10) and coal/rock interface cohesion (Cj =50 psi, 150 psi, and 300 psi) on pillar strength has been studied. The confinement effect of W/H ratio and interface shear strength is investigated by studying their effects on the average minimum principal stress developed in the pillar. The deformation behavior of the coal pillar is investigated. It is found that the pillar?s transition from strain softening to strain hardening behavior depends on its W/H ratio and the interface shear strength.

Jan 1, 2008

By Xinzhi Du

Coal strength is essential to analyze the stability of excavation in coal. It is well known that the strength of coal tested in the laboratory is size-dependent, and different size specimens will produce different strength. Many researchers have studied the uniaxial compressive strength of coal and developed a number of empirical formulae to describe the strength variation with specimen size. According to a comprehensive data base that includes most of the laboratory testing results in the last century in U.S. and South Africa, the size effect and shape effect were reviewed and analyzed. The results show that different groups of coal specimens have different size effect on the compressive strength. The critical size for the size effect from the data analysis is about 40 in. The shape (W/H) of the specimens has a large effect on the compressive strength. The pillar strength formulae obtained from the data regression have a larger strength than all other existing formulae. Most pillar strength formulae have their own place in coal pillar design field. In order to analyze the difference of those formulae, twelve design formulae have been selected to compare using the Pittsburgh coal seam. The intention is not to determine the preferred formulae, but only to compare them, and see how do the W/H ratio, width, length, angle, cross-section area and effective width affect different pillar strength formulae?

Jan 1, 2008

By S. P. Singh

Drifts are an integral component of underground mining. They provide access for men and material, means for transporting ore and rock and serve as air passageways. In view of their importance on the overall safety, economy and productivity of mines, empirical guidelines for controlled blasting design in drifts have been developed in this study. The application of the proposed concept was described by generating blast hole patterns for a mine with the help of a computer program. The mechanism of blast damage and the need for controlled blasting to alleviate ground control problems in underground mines have been outlined in this paper. The economic analysis between normal-and controlled blasting was performed based on the information from an operating mine. In addition, the review of drift blasting practices and problems in Canadian mines was also carried out in this study.

Jan 1, 1990

By Christopher Mark

Pillar recovery continues to be one of the more hazardous activities in underground coal mining. Safety requires that the roof above the intersection remain stable until after the pillar has been extracted. Artificial supports (timbers and Mobile Roof Supports) arc essential to roof stability, but so is the final remnant stump or pushout. Traditional mining practices usually called for the complete extraction of the final stump, but the recent trend (both in the U.S. and internationally) seems to be towards mining plans that leave a remnant stump. For this study, a sample of roof control plans from the Mine Health and Safety Administration (MSHA) Coal Districts were analyzed to determine current pillar recovery practices. Both full- and partial- extraction plans were included. Special attention was paid to whether plans require that a final stump be left, and whether requirements regarding the dimensions of the remnant stump are included. Foreign experience with final stumps is also summarized. It seems that the risk of major pillar falls can often be reduced by leaving final stumps that are large enough to protect the intersection, but small enough that they do not inhibit the caving of the gob. Because final stumps are often irregular in shape, a new approach for estimating their strength is described. Analyses were conducted to assess the effect of seam height and depth of cover on the potential variation in the size of remnant stumps.

Jan 1, 2001

By Thomas M. Barczak

The resultant load vector is the representation of the forces applied to a longwall roof support element by caving strata into a single, quantifiable measure of support resistance. The relatively complex kinematics of the shield support prohibit a determination of support resistance simply by summation of leg forces. A method is being investigated by the Bureau of Nines to determine the resultant load vector by instrumenting supports with pressure transducers and strain gages to measure leg, canopy capsule, and lemnisoate link forces. This concept has been laboratory tested in the Bureau's Nine Roof Simulator. Functional relationships among variables have been assessed, and confidence intervals have been established for prediction of the resultant load vector parameters.

Jan 1, 1984

By André C. Zingano

The coal pillars in room-and-pillar mining method are subjected to vertical stress due to overburden rock mass and horizontal stress relieve due to entries excavation around them. Some coal mining companies are applying rock bolts and steel straps to improve the pillar strength, consequently to reducing the pillar size and increasing coal recovery. This kind of approach deserves some discussion, whether it is pillar reinforcement or just rib support. The efficiency of pillar reinforcement (or rib support) is directly related to the initial load capacity of coal pillar, the type of excavation, and the width to high ratio of the pillar. The objective of this paper is to understand the mechanism of pillar reinforcement (or rib support) using rock bolts and steel straps on pillar ribs. Numerical simulation taking into account the relations listed above. The results showed that the increase of coal pillar strength is very short, and there is no influence on improvement of load capacity of pillar. However, the rib support avoids block falling, rib failure, and displacement, reducing the pillar failure propagation into the pillar center. Keywords: coal, pillar reinforcement, room and pillar.

Jan 1, 2006

By Ihsan Berk Tulu

In the Analysis of Retreat Mining Pillar Stability (ARMPS) program, the magnitude of the abutment loading adjacent to a gob area is calculated using an ?abutment angle? concept. The extent of the abutment loading is determined solely as a function of depth from an empirically derived equation. In the recommended calibration method for LaModel, it was believed that the empirical equations for calculating the magnitude and extent of the abutment load, as used in ARMPS, were the best available methods for determining these critical overburden loading values. Therefore, similar calculations were implemented in the LaModel calibration method. However, the latest in situ stress measurements of abutment loading performed in the United States and Australia have shown that there can be significant deviations in the measured abutment magnitude and extent as compared to the predicted values from the empirical formulas used in ARMPS and LaModel. It seems reasonable that the overburden geology, depth, extraction panel width, and mining height should have a significant effect on the extent and magnitude of the abutment load. However, the current empirical formulas do not incorporate many of these significant parameters into determining the abutment load on the pillars. In this paper, stress measurements from US and Australian mines were back-analyzed by using analytical and numerical methods to investigate the measured abutment extent and loading. Ultimately, it was determined that the original empirical abutment extent formula in conjunction with the original ALPS square-decay stress distribution function was supported by the case histories in this paper. Also, for depths less than 900 ft, the average 21° abutment angle was supported by the case histories; however, at depths greater than 900 ft, the abutment angle was found to be significantly less than 21° and should be calculated with a new proposed equation.

Jan 1, 2012

By Kot F. v. Unrug

The present combination of coal market prices and reserves, situated in the Central Appalachian Coal Field, is such that mining of smaller coal reserve blocks has become economically attractive. In above drainage deposits, and particularly under mountain ridges, overburden depth can be changing within a wide range. Mines operating in these deposits are usually developing mains along the center of the ridge, with panels projecting from the mains towards the outcrop. Due to changing topography, proximity of the outcrop, and related cover depth, the panels have various lengths. In this reported case study, a mine in Pike County, Kentucky, along the Kentucky ?West Virginia border, difficult ground conditions were encountered, during the development of the mains, under shallow cover, along a narrow mountain ridge. An area having unusual density of vertical joints was encountered. Mining operations were suspended because of roof stability concerns. The ground conditions were studied, analyzed, and control measures proposed to ensure safe passage through the difficult roof area of the mine. The advancement of the mains, through this area of challenging ground conditions, was successfully completed. In this paper, ground conditions are described, with an explanation of the geologic process contributing to their formation. It is interesting to note that similar locations were predicted by the authors, to be encountered in the same mine, based upon the experience gathered from studying conditions of the case described within this paper. When approaching the predicted locations, stability problems appeared to be even more challenging than those encountered previously. Due to changes in the coal market, mine management chose to move the affected mining section to another area of the mine having better coal quality. The advancement of the mains, through the difficult ground conditions, was temporarily postponed. Based upon the analysis of a probable kinematical mechanism of blocks in the mine roof, ground control measures were proposed. The actual application of these principles proved to be appropriate, ensuring safe passage through the difficult ground conditions encountered in the mine.

Jan 1, 2006

By Witold M. Pytel

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in-mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer prediction.

Jan 1, 1992

By John Popovich

The MICON RokLok binder system including component and consolidation processes and safety and its first aide are described. The implementation procedures and selection of injection parameters are discussed. Finally a case example of recovering a 30-ft. long roof fall in mainline haulage entry is used to illustrate the economic potential of preventive measures by RokLok injection.

Jan 1, 2001

By K. H. Brandt

A standard planning system for the development of roadways was adopted for German coal mines based on the results of geotechnical and rockmechanical investigations. Its goal is to provide for sufficient support systems under conditions of multiple seam mining at great depth. The report points out the required determination of geotechnical parameters and the basis for achieving a high level of planning reliability and resulting high performance in roadway development and longwall mining. The instrumentation and the planning procedure for selecting the support design most appropriate for the geotechnical conditions are described and demonstrated by examples.

Jan 1, 2004

By David C. Oyler

The Bureau of Mines conducted research at the 9-Right Section of the Olga Mine to determine the cause of bumps and aid in the development of appropriate control techniques. The purpose of this paper is to identify the factors which affect the occurrence of bumps at the Olga Mine. These factors have been broken down into two categories, in situ and mining related. The in situ factors include those conditions which exist prior to mining, such as variations in lithology and overburden, presence of jointing, the composition and the physical properties of the rock, and the original stress field existing in the coalbed and adjacent strata. The mining factors include the mining sequence, changes in stress in the coalbed and adjacent strata during mining, rates of convergence, and the pattern of failure of the coal and adjacent strata. The factors which appeared to have the greatest effect on bumping were the overburden, the lithology of the roof and floor rock and the physical properties of the rock. The roof rock is generally a massive, stiff sandstone which does not break until coal pillar extraction is complete. The immediate floor is a strong shale which generally grades into siltstone and then into sandstone. The overburden at 9-Right ranged from 990 to 1,600 ft. Secondary factors appeared to be the in situ (pre-mining) stress and the mining sequence. When barrier pillars were split., pressures measured in hydraulic cells (Borehole platen flatjacks) located in those barriers showed large pressure increases, and the incidence of bumps increased, especially when the barriers were near old gob areas. The pillar extraction system used at Olga, where three rows of pillars are mined concurrently, appears to reduce pillar loads at the face areas, thereby reducing the exposure of men and equipment to the risks of bumps during mining operations. The horizontal components of in situ stresses at Olga were found to be nearly the same as those at 5 other mines in southern WV, where humps were not common, so it appears that horizontal in situ stress alone is not a major influence on bumping at the Olga Mine.

Jan 1, 1987