Search Documents

By P. Gaskell

The paper examines the development of rock movement between a longwall extraction horizon and the surface for a fully caved mining situation. Physical modelling has been used to examine the mechanics of ground movement and the propagation of fractures around the longwall working. The paper discusses dimensional analysis, model construction and measurement technique and data processing of the results into effective graphical forms for further study.

Jan 1, 1988

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By V. D. Jalevsky

A new methodology of an experimental-analytical approach has been developed. It is used in building an information geomechanic monitoring system for the modeling of geomechanic processes during coal seam working. The approach synthesizes experimental (in-situ) measurements of rock pressure manifestation in separate points, methods of numerical modeling of processes on rock boundaries with coal, and a seam analytical calculation of rock mass in a spatial strained state. One of the realizations of this approach is the developed theory and calculation method of adjoining rock surface shift (overhang) formation during underground working of sheet deposits and of rock mass geomechanic state determination. There are description algorithms of cavity configurations with broken lengths of faces during underground working of useful mineral sheet deposits. These algorithms have been used in computer modeling of formations of adjoining rock surface overhangs and abutment pressure upon rock mass in the area of coal faces with irrectilinear longwalls. Peculiarities of surfaces shifts and stress allocation are established for different face schemes. The use of theory and methods alloww working out techniques of automatic control to receive processing algorithms of RPM measurement results and calculate geomechanic situations within panels in the process of planning and development as well as during mining, i.e., to carry out long-term prediction, in-line control, and short-term prediction of rock pressure manifestations.

Jan 1, 1996

By N. P. Kripakov

Results of a complex three-seam interaction analysis in a western U.S. coal mine are presented. The physical situation simulated by the models represents the development of a set of entries underneath two previously mined seams with all three seams in proximity to each other. The layout and the geometry of the remnant pillars in the upper seams were nonuniform and not always directly superimposed over each other, creating a very challenging modeling problem. The U.S. Bureau of Mines' MULSIM/PC computer code was upgraded and enhanced to perform the required three-seam interaction calculations. Analysis was limited to simple linear-elastic assumptions as only peak stresses were required. Results clearly indicated that stress concentrations in the lower seam increased approximately 100 percent when compared to cases simulating no extraction in the two upper seams. These stress concentrations generally occurred in zones directly below points of highest abutment pressures in the upper seams. Overall, the model results compared favorably with actual documented observed behavior where roof failures were known to have occurred.

Jan 1, 1996

Knowledge of initial ground pressures or in-situ stresses and mechanical properties and geological conditions is of great importance in drivage and maintenance of a mine roadway. Field measurements of the in-situ stresses and the geological and mechanical properties have been carried out. However, these methods are really impractical in using in underground mines. Alternatively, back analysis method using measured displacements during drivage of roadway can be used. The paper presents discussion on some problems in applying inverse formulation of back analysis to a roadway driven in an in- homogeneous rock mass. The back analysis is formulated by 2-0 finite element method. The inverse procedure is carried out using a microcomputer, but for the multi-rock layer, a larger computer or a main-frame computer is used due to an iterative procedure.

Jan 1, 1990

By Robert G. Harris

During the last five years there have been significant improvements in face support monitoring techniques particularly in respect of face pressure. The measurement of support loading pressures was originally conceived as a maintenance aid for the hydraulic systems but recent work has also included geological loading displays of the complete face as well as individual supports. This paper briefly examines the means of obtaining this information, together with some examples of actual face data. Also included is a summary of the benefits of such monitoring and an outline of future development work.

Jan 1, 1993

By B Whittaker

The paper examines the role of chain pillars in longwall mining layouts as used in several countries. The application of chain pillars in relation to their expected design role is discussed. An important feature is the specification of the pillar design to meet strata loading conditions as imposed by the mining and geological setting. The paper relates longwall width and chain pillar configurations to pillar size to satisfy anticipated loading and strength expectations. Laboratory work is referred to which examines criteria for pillar stability. Comments are made regarding the application of the findings presented in the paper, to different situations involving the use of chain pillars in longwall and shortwall mining systems.

Jan 1, 1987

By Arun Kumar Singh

Wide variation in the nature of the coal seams and the surrounding rock mass of the Indian coalfields and very little information about the associated stress fields were observed to be the major hurdles in the straight forward application of a continuous miner (CM) based mechanised depillaring approach. Due to various techno-economic reasons, a considerably large number of coal seams have been developed and are standing on pillars in India. The development of pillars is done as per Indian coal mines regulation, which results in pillars of relatively large size. In fact, the large size of the pillars provides stiff natural support to control caving of the massive overlying strata. However, the size of these pillars is not conducive for the single pass pillar stripping technique and, therefore, there is a need for pillar splitting before pillar extraction/retreating. Splitting of the pillar may reduce the competency/stiffness of the pillar, which creates a chance of overriding during final extraction below a massive roof stratum. This paper first discusses the existing coal mining scenario in India followed by a brief presentation of geo-technical details of pillar extraction at the three sites where a CM has been introduced for depillaring/pillar retreating in the country to date. Based on past rock mechanics experiences with conventional depillaring faces, stability issues of the pillars, fenders, and stumps in and around the depillaring face are discussed. This may prove to be an important factor in the success of future CM faces. It is recognized that the application of the modern strata movement monitoring techniques may improve operation safety by providing valuable qualitative and quantitative information that can be used to improve the design of modern concepts like roof bolt based breaker line support during pillaring.

Jan 1, 2009

The basic objectives of mine roadways are to provide sufficient cross sections in order to meet the needs of accommodation of equipment, transport, personnel travel and ventilation. However, many roadways become damaged to the extent of needing maintenance, generally dinting, and in some cases requiring re-ripping. The damaging of a roadway is a result of several factors including geological properties of surrounding strata, method of roadway formation, type and spacing of support and so on. Among these factors, strata conditions play an important effect on the stability of roadway. Weak rocks cause excessive roadway closures and water softens some rocks and promotes the closure problem. In this paper, a scientific discussion on the effect of water on the stability of roadways is given on the basis of results obtained by means of in-situ investigation and laboratory rock tests.

Jan 1, 1996

By Jun Han

Coal has been mined in the Kailuan mining area for more than 130 years. The remaining reserves consist of, in large part, coals that would have been considered economically unminable or technically not feasible by the previous generations. Some of the current operations have to resort to overmining because the lower seams had been extracted in the past. This paper deals with the feasibility and proper layout of mining roadways of overmining carried out in the No. 5 seam of Qianjiaying coal mine of Kailuan mining area using numerical and physical simulation. FLAC2D was used to investigate the characteristics of stress and displacement in the overburden after extraction of the lower seams. It also analyzed the proper layouts of gateroads in the upper seams, i.e. locating them in the stress-relief zone of the gob so that their stability can be easily maintained. In addition, a two-dimensional physical model was constructed for investigation of damages to the upper seams due to mining of the lower seams. Finally, based on the results of investigations, proper gateroads layout was designed and successful extraction was implemented for panel 1357 in the No.5 seam.

Jan 1, 2009

By Kot F. Unrug

Strength of coal is one of the governing factors in size determination of mine pillars, and therefore affects the percentage of extraction and thus, utilization of reserves. Coal strength is also important from the subsidence control standpoint, where mine pillars with appropriate safety factors should be designed for long term stability. Determination of coal seam strength has been addressed through the extrapolation of the coal strength obtained from a small number of samples on the whole section of the seam. This procedure often gives unreliable results. Presented in this paper is a method of in-situ strength testing of coal, allowing for a realistic determination of seam strength. Results of a field case study dealing with the coal seam, where samples for the laboratory strength tests could not be obtained due to the dense cleat, are presented. However, in these conditions, the in-situ testing was successful. A comparison of both conventional and the in-situ penetrometer method was carried out. It was found that the penetrometer data not only improve the accuracy of strength determination of the entire seam, but also prove to be much more cost effective than the conventional method on a per test basis.

Jan 1, 1995

By Floyd D. Varley

Outbursts, the sudden and violent out- pouring of material into mine openings, is a ground control problem increasingly encountered in the United States as deeper seams are developed. Outbursts, caused by several mechanisms, are the result of the loading of ground support systems be- yond their designed capacity to failure, manifested in a violent release of stored energy. There are several types of outbursts typical to deep underground coal mines. - Outbursts of the coal face due to the presence of pressure abutments in close proximity to the face. These outbursts are usually accompanied by liberation of large amounts of methane. - Instantaneous convergence of the ribs and floor due to overloading and failure of ribs which lengthens the beam of floor strata sometimes resulting in a chain reaction failure of the mine floor. - violent failure of the confined core of a pillar due to rapid loading beyond the yield point of the pillar.

Jan 1, 1986

By Jian Wu

In this paper, the surrounding rocks and the supports in a longwall are taken as an integral, i.e. a system. The structural characteristics and behavior of the system are discussed based on in-situ observations. A set of equations, which describe the interaction among the support, immediate roof and main roof, are developed. These equations can be used to design the longwall powered supports more reasonably and economically.

Jan 1, 1989

By Guoqi He

Common offset seismic data collected over two active longwall panels at different stages of mining reveal that significant arrival time delays are produced in reflections from different levels within the mine cover. Mining-induced arrival time delays are also observed beyond the edges of the mine over unmined areas. Reflection arrival time delays increase with reflector depth and are laterally variable. The arrival time delays are produced by reductions of seismic velocity within the overburden. Reflection arrival time delays from a major strong unit located neutrally within the cover are proportional to subsidence, however, delays in other events are not.

Jan 1, 1989

By Bruce Hebblewhite

This paper recognises the 25th year of the Morgantown International Ground Control in Mining Conference, by offering a twenty five year review of ground control in the Australian mining industry ? primarily in underground coal. The paper provides an overview of the developments in ground control design methodologies, practices and products. It not only summarises what has been done, but attempts to highlight at least some of the major issues, significant developments, controversies and areas of contention, plus some of the continuing gaps in our understanding or capabilities as we go forward into the next 25 years. Some of the issues included are in relation to: the development of the high strength bolt and cable reinforcement practices widely adopted today and the contrast between stiff and soft systems; a focus on local detail, at the expense of understanding regional stability concerns; dramatic improvements in the use of, and systems available for underground geotechnical instrumentation and monitoring; some of the ground control management trends, including occupational health and safety concerns, availability of suitably trained staff and legislative requirements; the opposing approaches of the empiricists versus the numerical modellers ? is there some middle ground?

Jan 1, 2006

By V. M. Shick

With gentle bedding within the zone of support pressure the delamination in roof rocks may occur only on those stratification planes where cohesiveness of rock is close to zero. Unlike this, at dip angles of more than 30-35° disintegration of rock occurs on the surfaces with cohesion up to 5 MPa. Therefore, the delamination in roof rocks at inclined beds is greater than at gently dipping ones. The original disintegration along the pressure fissures with the formation of block structure at inclined strata is not typical, and it may be observed only in roofs with included thick rocks; in this case, the orientation of fractures depends on the angle of seam inclination. Deformation of roof roocks above the mined-out space is determined by anisotropy of layers stiffness (hardness). With the increase of dip angle the own bearing capacity of layers will rise in the direction of strike. It was emphasized that the natural and technological factors are of great importance for rock pressure manifestation in longwalls.

Jan 1, 1996

By G. C. Sun

Rock mechanics properties, i.e. uniaxial and triaxial compressive strength, indirect tensile strength shear strength, Young's modulus, and poisson's ratio were collected for coal and related strata from 50 coal seams in 90 mines. The methodology of data organization and retrieval is described in details. The values and .ranges of those properties are also discussed.

Jan 1, 1993

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

By P. M. Lin

A subsidence monitoring program over a longwall panel was established (1) to explore the impacts of dynamic subsidence on the ground surface and structures and (2) to correlate the movements between the structures and their corresponding points on the ground. The program consisted of a transverse line survey and a series of survey points around the structures on the ground surface and their corresponding survey points on the exterior walls of the structures. The vertical displacement of each point can be expressed as: where Si is subsidence at i point; Sif is the final subsidence at i point; F is face location in terms of distance from the i point and SD is seam depth. The development of subsidence can be divided into five stages. Damage to the structures starts at the beginning of the second stage, The maximum damage developed in the middle of the third stage. The relationship of the vertical displacement between ground surface and structures can be expressed as: G = aH + b where G is ground displacement, H is structures displacement, and a and b are constants. The relationship is linear. However, the strain is non-linear and more complicated because of the interaction of the ground surface and structure.

Jan 1, 1989

By Yi Luo

In the study of the topographical effects on surface movement due to underground longwall mining, the factors that affect the incremental horizontal displacements are identified using 10 collected cases. Based on this study, the angle of surface natural slope is the major contributor to the incremental horizontal displacement while the total movement is also playing an important role in some cases.

Jan 1, 1996